SEARCH · Engineering Papers

Results for “resonance structures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

All sources NASA NTRS DOE OSTI

NASA NTRS1975

Airloads near the open port of a one-meter airborne telescope

An infrared telescope is mounted in a cavity in the fuselage of a C-141 airplane. The cavity is sealed off from the rest of the fuselage and can be opened to the outside for viewing. A retractable porous spoiler is installed ahead of the opening to inhibit cavity resonance. The paper presents the mean pressures, pressure fluctuations, spectra, phase, and coherence of the pressures in the cavity and on the fuselage near the cavity, along with pertinent acceleration and torque information for the aircraft structure and telescope. It is shown that a moderate spoiler extension controls resonance in normal flight attitudes and produces a cavity environment with approximately the same turbulence intensity as an attached turbulent boundary layer.

Buell, D. A.↗

NASA NTRS1980

Helicopter theory

A comprehensive presentation is made of the engineering analysis methods used in the design, development and evaluation of helicopters. After an introduction covering the fundamentals of helicopter rotors, configuration and operation, rotary wing history, and the analytical notation used in the text, the following topics are discussed: (1) vertical flight, including momentum, blade element and vortex theories, induced power, vertical drag and ground effect; (2) forward flight, including in addition to momentum and vortex theory for this mode such phenomena as rotor flapping and its higher harmonics, tip loss and root cutout, compressibility and pitch-flap coupling; (3) hover and forward flight performance assessment; (4) helicopter rotor design; (5) rotary wing aerodynamics; (6) rotary wing structural dynamics, including flutter, flap-lag dynamics ground resonance and vibration and loads; (7) helicopter aeroelasticity; (8) stability and control (flying qualities); (9) stall; and (10) noise.

Johnson, W.↗

NASA NTRS1991

Optically addressed asymmetric Fabry-Perot modulator

A low power, high contrast optically addressed modulator, operating with normal incidence, has been fabricated. Optically controlled reflection modulation is achieved through optically induced absorption modulation in a periodically delta-doped InGaAs/GaAs multiple quantum well structure inserted in an integrated asymmetric Fabry-Perot resonator. A contrast ratio over 60:1 was measured using a spectrally matched low power InGaAs/GaAs quantum well laser to generate the write (control) signal. The insertion loss for the normally off modulator is 4.6 dB at the highest write signal power (30 mW) used. The device lends itself to the fabrication of arrays for optically addressed spatial light modulation.

Larsson, A.↗

NASA NTRS1992

Chaotic scattering of pitch angles in the current sheet of the magnetotail

The modified Harris field model is used to investigate the process of pitch angle scattering by a current sheet. The relationship between the incoming asymptotic pitch angle alpha(in) and the outgoing asymptotic pitch angle alpha(out) is studied from first principles by numerically integrating the equation of motion. Evidence that charged particles undergo chaotic scattering by the current sheet is found. For fixed alpha(in), it is shown that alpha(out) exhibits sensitive dependence on the energy parameter in certain energy ranges. For a fixed energy parameter value in the same energy ranges, alpha(out) sensitively depends on alpha(in). For other energy values, alpha(out) does not show sensitive dependence on alpha(in) for most phase angles. A distribution of alpha(in) is mapped from the asymptotic region to the midplane, and it is found that the resulting particle distribution should have beam structures with well-collimated pitch angles near each resonance energy value. Implications for the particle distribution functions in the earth's magnetotail are discussed.

Burkhart, G. R.↗

NASA NTRS1995

HTS thin films: Passive microwave components and systems integration issues

The excellent microwave properties of the High-Temperature-Superconductors (HTS) have been amply demonstrated in the laboratory by techniques such as resonant cavity, power transmission and microstrip resonator measurements. The low loss and high Q passive structures made possible with HTS, present attractive options for applications in commercial, military and spacebased systems. However, to readily insert HTS into these systems improvement is needed in such areas as repeatability in the deposition and processing of the HTS films, metal-contact formation, wire bonding, and overall film endurance to fabrication and assembly procedures. In this paper we present data compiled in our lab which illustrate many of the problems associated with these issues. Much of this data were obtained in the production of a space qualified hybrid receiver-downconverter module for the Naval Research Laboratory's High Temperature Superconductivity Space Experiment 2 (HTSSE-2). Examples of variations observed in starting films and finished circuits will be presented. It is shown that under identical processing the properties of the HTS films can degrade to varying extents. Finally, we present data on ohmic contacts and factors affecting their adhesion to HTS films, strength of wire bonds made to such contacts, and aging effects.

Miranda, F. A.↗

NASA NTRS1995

HTS Thin Films: Passive Microwave Components and Systems Integration Issues

The excellent microwave properties of the High-Temperature-Superconductors (HTS) have been amply demonstrated in the laboratory by techniques such as resonant cavity, power transmission and microstrip resonator measurements. The low loss and high Q passive structures made possible with HTS, present attractive options for applications in commercial, military and space-based systems. However, to readily insert HTS into these systems, improvement is needed in such areas as repeatability in the deposition and processing of the HTS films, metal-contact formation, wire bonding, and overall film endurance to fabrication and assembly procedures. In this paper, we present data compiled in our lab which illustrate many of the problems associated with these issues. Much of this data were obtained in the production of a space qualified hybrid receiver-downconverter module for the Naval Research Laboratory's High Temperature Superconductivity Space Experiment II (HTSSE-II). Examples of variations observed in starting films and finished circuits will be presented. It is shown that under identical processing the properties of the HTS films can degrade to varying extents. Finally, we present data on ohmic contacts and factors affecting their adhesion to HTS films, strength of wire bonds made to such contacts, and aging effects.

Miranda, F. A.↗

NASA NTRS1999

Diode Laser Velocity Measurements by Modulated Filtered Rayleigh Scattering

The ability of solid-state lasers to be tuned in operating frequency at MHz rates by input current modulation, while maintaining a relatively narrow line-width, has made them useful for spectroscopic measurements. Their other advantages include low cost, reliability, durability, compact size, and modest power requirements, making them a good choice for a laser source in micro-gravity experiments in drop-towers and in flight. For their size, they are also very bright. In a filtered Rayleigh scattering (FRS) experiment, a diode laser can be used to scan across an atomic or molecular absorption line, generating large changes in transmission at the resonances for very small changes in frequency. The hyperfine structure components of atomic lines of alkali metal vapors are closely spaced and very strong, which makes such atomic filters excellent candidates for sensitive Doppler shift detection and therefore for high-resolution velocimetry. In the work we describe here we use a Rubidium vapor filter, and work with the strong D(sub 2) transitions at 780 nm that are conveniently accessed by near infrared diode lasers. The low power output of infrared laser diodes is their primary drawback relative to other laser systems commonly used for velocimetry. However, the capability to modulate the laser frequency rapidly and continuously helps mitigate this. Using modulation spectroscopy and a heterodyne detection scheme with a lock-in amplifier, one can extract sub-microvolt signals occurring at a specific frequency from a background that is orders of magnitude stronger. The diode laser modulation is simply achieved by adding a small current modulation to the laser bias current. It may also be swept repetitively in wavelength using an additional lower frequency current ramp.

Mach, J. J.↗

NASA NTRS2000

High-Q X-Band and K-Band Micromachined Spiral Inductors for Use in Si-Based ICs

A micromachined structure with reduced parasitics is proposed to enhance the resonant frequency and the quality factor (Q) of a spiral inductor. Inductors with various etch depths have been fabricated on a high resistivity Si substrate. Two-port S-parameters measurement is taken to characterize the performance of the inductors. With an etch depth of 20 micron, a fabricated 1.8 nH spiral inductor achieves a maximum resonant frequency of 25.6 GHz and a maximum Q of 20.2 at 14.5 GHz. This technology is compatible with SiGe/Si HBT technology, and the spiral inductors are especially suitable for Si-based monolithic microwave integrated circuit (MMIC) applications.

Lu, Liang-Hung↗

NASA NTRS2001

Seismic Study of the Dynamics of the Solar Subsurface from SoHO Observations

In collaboration with Dr. Baudin, we have developed and refined the new observational methodology for local helioseismology known as time-distance analysis. Global helioseismology study the solar oscillations as a superposition of resonant modes, whose properties (mode frequencies) reflect the global structure of the sun (sound speed stratification, rotation rate, etc). In contrast, local helioseismology look at the solar oscillations as wave packets whose propagation will be affected by perturbations of the media sampled. These local perturbations (sound speed or velocity flows) will modify the propagation time, that in turn can be used as a diagnostic tool for a given region. From a data reduction perspective, the processing of solar dopplergrams that result in time-distance maps, i.e. propagation times as a function of distance between bounces at the surface, is radically different from the methodology used for global mode analysis. We have, in a first step, further develop the programs needed to carry out such analysis. We have then applied them to NMI data set, and explore the trade-off between various averaging and filtering approaches - steps required to improve the signal-to-noise ratio of correlation maps - and the resulting stability and precision of the fitted propagation times. While excessive averaging (whether over space, propagation distance, or time) will reduce the diagnostic potential of the method, insufficient averaging lead to unstable fits, or uncertainties so large as to hide the information we seek. In a second phase, we have developed the analysis methodology required to infer local properties from perturbation in time propagation. Namely, we have developed time-distance inversion techniques, with an emphasis on inferences of velocity flows from time anomalies. Note also that during the period covered by this grant, all the investigators on this proposal (i.e., Drs. Baudin, Eff-Darwich, Korzennik, and Noyes) took part in the organization of the SOHO 6 /GONG 99 Workshop: Structure and Dynamics of the Interior of the Sun and Sunlike Stars, held on June 1-4 1999 at the Boston Park Plaza Hotel in Boston, Massachusetts, USA. it was very well attended by more than 160 participants from 26 countries from all over the world. The proceedings were published in two volumes as ESA SP-418, with Sessions I-III in Volume 1, and Sessions IV-VI in Volume 2 (1,000 pages in total). The complete contents are also included in digital form on a CD-ROM included with Volume 1. This CD-ROM also contains additional multi-media material that complements some of the contributions.

Korzennik, Sylvain G.↗

NASA NTRS2005

Measurement of absolute cross sections for excitation of the 2s(2) S-1 -> 2s2p P-1 degrees transition in O+4

Experimental cross sections are reported for the 1s(2)2s(2) S-1 -> 1s(2)2s2p P-1(o) transition in O+4 located at 19.689 eV. Use is made of the electron energy-loss method, using a merged electron-ion beam geometry. The center-of-mass interaction energies for the measurements in the S-1 -> P-1(o) transition are in the range 18 eV ( below the threshold) to 30 eV. Data are compared with other previous electron energy-loss measurements and with results of a 26 term R-matrix calculation that includes fine structure explicitly via the Breit-Pauli Hamiltonian. Clear resonance enhancement is observed in all experimental and theoretical results near the threshold for this S-1 -> P-1(o) transition.

atomic processes↗

NASA NTRS1999

Left-handed Z-DNA: structure and function

Z-DNA is a high energy conformer of B-DNA that forms in vivo during transcription as a result of torsional strain generated by a moving polymerase. An understanding of the biological role of Z-DNA has advanced with the discovery that the RNA editing enzyme double-stranded RNA adenosine deaminase type I (ADAR1) has motifs specific for the Z-DNA conformation. Editing by ADAR1 requires a double-stranded RNA substrate. In the cases known, the substrate is formed by folding an intron back onto the exon that is targeted for modification. The use of introns to direct processing of exons requires that editing occurs before splicing. Recognition of Z-DNA by ADAR1 may allow editing of nascent transcripts to be initiated immediately after transcription, ensuring that editing and splicing are performed in the correct sequence. Structural characterization of the Z-DNA binding domain indicates that it belongs to the winged helix-turn-helix class of proteins and is similar to the globular domain of histone-H5.

Review↗

NASA NTRSDate not supplied

Development of an Additively Manufactured Turbine Blade Tuned Mass Absorber

An innovative concept using a tuned mass absorber for resonant response reduction of turbine blades that is integrally fabricated into the blades using additive manufactured has been developed. Avoiding high resonant response and resulting high cycle fatigue failure is a major concern of the $100B worldwide turbine industry, which encompasses power generation, jet engines and rocket engine turbomachinery. Blade failure is potentially catastrophic, and although preventative measures using dampers do exist, these solutions are extremely expensive to develop and are not always effective. In addition, many of the existing techniques do not work for newer integrally bladed disks (or blisks), where there is no inherent damping in the assembly. The proposed concept, in which a tuned mass absorber re-arranges the structural dynamics and moves energy from the blade to the absorber, is designed specifically for blisks, and is intentionally linear, enabling accurate response prediction during design. Single blade prototypes have been analyzed, fabricated, and tested, and different absorber concepts have shown a reduction in response of up to 60%. After an extensive commercialization and prior art search, MSFC determined the innovation merited the generation and submission of a patent application in August ’21. Funding is now being sought to fabricate a 20-bladed blisk which would be spun at operational speeds with substantially higher and more realistic pressure loads in a special spin facility. Successful completion of this program would raise the TRL from 3/4 to 6/7, significantly improving the viability for adoption of the concept not only in rocket engines but other industrial applications as well.

Turbine Blades↗

NASA NTRS1982

An observation of LHR noise with banded structure by the sounding rocket S29 Barium-GEOS

The measurement of electrostatic and obviously locally produced noise near the lower hybrid frequency made by the sounding rocket S29 Barium-GEOS is reported. The noise is strongly related to the spin of the rocket and reaches well below the local lower hybrid resonance frequency. Above the altitude of 300 km the noise shows banded structure roughly organized by the hydrogen cyclotron frequency. Simultaneously with the banded structure, a signal near the hydrogen cyclotron frequency is detected. This signal is also spin related. The characteristics of the noise suggest that it is locally generated by the rocket payload disturbing the plasma. If this interpretation is correct we expect plasma wave experiments on other spacecrafts, e.g., the space shuttle to observe similar phenomena.

Koskinen, H. E. J.↗

NASA NTRS1986

Resonance ionization mass spectrometry for isotopic abundance measurements

Resonance ionization mass spectrometry (RIMS) is a relatively new laser-based technique for the determination of isotopic abundances. The resonance ionization process depends upon the stepwise absorption of photons from the laser, promoting atoms of the element of interest through progressively higher electronic states until an ion is formed. Sensitivity arises from the efficiency of the resonant absorption process when coupled with the power available from commercial laser sources. Selectivity derives naturally from the distinct electronic structure of different elements. This isobaric discrimination has provided the major impetus for development of the technique. Resonance ionization mass spectrometry was used for analysis of the isotopic abundances of the rare earth lutetium. Isobaric interferences from ytterbium severely effect the ability to measure small amounts of the neutron-deficient Lu isotopes by conventional mass spectrometric techniques. Resonance ionization for lutetium is performed using a continuous-wave laser operating at 452 nm, through a sequential two-photon process, with one photon exciting the intermediate resonance and the second photon causing ionization. Ion yields for microgram-sized quantities of lutetium lie between 10(6) and 10(7) ions per second, at overall ionization efficiencies approaching 10(-4). Discrimination factors against ytterbium greater than 10(6) have been measured. Resonance ionization for technetium is also being explored, again in response to an isobaric interference, molybdenum. Because of the relatively high ionization potential for Tc, three-photon, two-color RIMS processes are being developed.

Miller, C. M.↗

NASA NTRS2004

Modeling of a Variable Focal Length Flat Lens Using Left Handed Metamaterials

Left Handed Metamaterials (LHM) were originally purposed by Victor Veselago in1968. These substances would allow a flat structure to focus electromagnetic (EM) waves because they have a negative index of refraction. A similar structure made from conventional materials, those with a positive index of refraction, would disperse the waves. But until recently, these structures have been purely theoretical because substances with both a negative permittivity and negative permeability, material properties necessary for a negative index of refraction, do not naturally exist, Recent developments have produced a structure composed of an array of thin wires and split ring resonators that shows a negative index of refraction. area smaller than a square wavelength. How small the area is can be determined by how perfectly the lens is polished and how pure the substance is that composes the lens. These lenses must also be curved for focusing to occur. The focal length is determined by the curvature of the lens and the material. On the other hand, a flat structure made from LHM would focus light because of the effect of a negative index of refraction in Snell s law. The focal length could also be varied by simply adjusting the distance of the lens from the source of radiation. This could create many devices that are adjustable to different situations in fields such as biomedical imaging and communication. the software package XFDTD which solves Maxwell s equations in the frequency domain as well as the time domain. The program used Drude models of materials to simulate the effect of negative permittivity and negative permeability. Because of this, a LHM can be simulated as a solid block of material instead of an array of wires and split ring resonators. After a flat lens is formed, I am to examine the focusing effect of the lens and determine if a higher resolution flat lens can be developed. Traditional lenses made from conventional materials cannot focus an EM wave onto an My goal was to model LHMs and create a flat lens from them. This was to be done using

Reinert, Jason↗

NASA NTRS1997

Glycolonitrile oligomerization: structure of isolated oxazolines, potential heterocycles on the early earth

A study of glycolonitrile polymerization has led to the isolation and characterization of two 2,5-dihydro-4-aminooxazoles, 4 and 5. Previous reports have misassigned these structures as s-triazines or pyrimidines. X-ray diffraction analysis of crystals of 4 and an acetylated oxazole derivative of 5 (6) confirm the proposed structures. Ab initio computations are used to assess the relative thermodynamic stability of three trimer isomers (an s-triazine, an aminohydroxypyrimidine, and an aminooxazoline), and the results indicate that 4 is a novel kinetic product. Mechanistic considerations rationalize kinetic oxazole formation over the more customary triazine or pyrimidine trimers.

Non-NASA Center↗

NASA NTRS1979

Field resonance propulsion concept

A propulsion concept was developed based on a proposed resonance between coherent, pulsed electromagnetic wave forms, and gravitational wave forms (or space-time metrics). Using this concept a spacecraft propulsion system potentially capable of galactic and intergalactic travel without prohibitive travel times was designed. The propulsion system utilizes recent research associated with magnetic field line merging, hydromagnetic wave effects, free-electron lasers, laser generation of megagauss fields, and special structural and containment metals. The research required to determine potential, field resonance characteristics and to evaluate various aspects of the spacecraft propulsion design is described.

Holt, A. C.↗

NASA NTRS2002

Evaluation of Mechanical Modal Characteristics Using Optical Techniques

In this paper the sensitivity of embedded fiber optic sensors to changes in modal characteristics of plates is discussed. In order to determine the feasibility of embedded fiber Bragg gratings for the detection of modal shapes and modal frequencies, a comparison of holographically imaged modes and the detected dynamic strain from embedded fiber optic Bragg gratings is made. Time averaged optical holography is used for the detection of mechanical defects, or damage, in various aerospace components. The damage is detected by measuring an alteration in structural dynamics, which is visually apparent when using time-averaged holography. These shifts in the mode shapes, both in frequency of the resonance and spatial location of vibration nodes, are caused by changes in parameters that affect the structure's mechanical impedance, such as stiffness, mass and damping, resulting from cracks or holes. It is anticipated that embedded fiber optic sensor arrays may also be able to detect component damage by sensing these changes in modal characteristics. This work is designed to give an initial indication to the feasibility of damage detection through the monitoring of modal frequencies and mode shapes with fiber optic sensors.

Lekki, John↗