Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “failure detection”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Feasibility of an on-line fission-gas-leak detection system

Calculations were made to determine if a cladding failure could be detected in a 100-kW zirconium hydride reactor primary system by monitoring the highly radioactive NaK coolant for the presence of I-131. The system is to be completely sealed. A leak of 0.01 percent from a single fuel pin was postulated. The 0.364-MeV gamma of I-131 could be monitored on an almost continuous basis, while its presence could be varified by using a longer counting time for the 0.638-MeV gamma. A lithium-drifted germanium detector would eliminate radioactive corrosion product interference that could occur with a sodium iodide scintillation detector.

Lustig, P. H.↗
NASA NTRS1982

The P-POD Project

The programmable pilot oriented display (P-POD), a multiprocessor based flight information processing and display unit, is discussed. Communication protocols between the three Z-80 processors inside P-POD are reviewed. The interface between the video processor, P2, and the main processor, P1, was tested. Hardware and software were revised. Data flow between P1 and P2 is illustrated. While running diagnostic routines to exercise the P1/P2 interface at maximum speed an intermittent failure was observed. A check of possible noise sources or race conditions in the hardware did not reveal the source of this failure. Possible software timing problems were also fully investigated. To eliminate the effects of this type of failure a performance monitor routine was used to detect these occasional failures and correct them. The data transmission cycle between P1/P2 is either allowed to continue normal operation or is re-initialized and restarted when an error is detected.

Littlefield, J. A.↗
NASA NTRS1990

Framework for a space shuttle main engine health monitoring system

A framework developed for a health management system (HMS) which is directed at improving the safety of operation of the Space Shuttle Main Engine (SSME) is summarized. An emphasis was placed on near term technology through requirements to use existing SSME instrumentation and to demonstrate the HMS during SSME ground tests within five years. The HMS framework was developed through an analysis of SSME failure modes, fault detection algorithms, sensor technologies, and hardware architectures. A key feature of the HMS framework design is that a clear path from the ground test system to a flight HMS was maintained. Fault detection techniques based on time series, nonlinear regression, and clustering algorithms were developed and demonstrated on data from SSME ground test failures. The fault detection algorithms exhibited 100 percent detection of faults, had an extremely low false alarm rate, and were robust to sensor loss. These algorithms were incorporated into a hierarchical decision making strategy for overall assessment of SSME health. A preliminary design for a hardware architecture capable of supporting real time operation of the HMS functions was developed. Utilizing modular, commercial off-the-shelf components produced a reliable low cost design with the flexibility to incorporate advances in algorithm and sensor technology as they become available.

Hawman, Michael W.↗
NASA NTRS1983

Models of human problem solving - Detection, diagnosis, and compensation for system failures

The role of the human operator as a problem solver in man-machine systems such as vehicles, process plants, transportation networks, etc. is considered. Problem solving is discussed in terms of detection, diagnosis, and compensation. A wide variety of models of these phases of problem solving are reviewed and specifications for an overall model outlined.

Rouse, W. B.↗
NASA NTRS2010

Data-Driven Anomaly Detection Performance for the Ares I-X Ground Diagnostic Prototype

In this paper, we will assess the performance of a data-driven anomaly detection algorithm, the Inductive Monitoring System (IMS), which can be used to detect simulated Thrust Vector Control (TVC) system failures. However, the ability of IMS to detect these failures in a true operational setting may be related to the realistic nature of how they are simulated. As such, we will investigate both a low fidelity and high fidelity approach to simulating such failures, with the latter based upon the underlying physics. Furthermore, the ability of IMS to detect anomalies that were previously unknown and not previously simulated will be studied in earnest, as well as apparent deficiencies or misapplications that result from using the data-driven paradigm. Our conclusions indicate that robust detection performance of simulated failures using IMS is not appreciably affected by the use of a high fidelity simulation. However, we have found that the inclusion of a data-driven algorithm such as IMS into a suite of deployable health management technologies does add significant value.

Martin, Rodney A.↗
NASA NTRS1990

Real-time diagnostics of the reusable rocket engine using on-line system identification

A model-based failure diagnosis system has been proposed for real-time diagnosis of SSME failures. Actuation, sensor, and system degradation failure modes are all considered by the proposed system. In the case of SSME actuation failures, it was shown that real-time identification can effectively be used for failure diagnosis purposes. It is a direct approach since it reduces the detection, isolation, and the estimation of the extent of the failures to the comparison of parameter values before and after the failure. As with any model-based failure detection system, the proposed approach requires a fault model that embodies the essential characteristics of the failure process. The proposed diagnosis approach has the added advantage that it can be used as part of an intelligent control system for failure accommodation purposes.

Guo, T.-H.↗
NASA NTRS2011

Accelerated Aging Experiments for Prognostics of Damage Growth in Composite Materials

Composite structures are gaining importance for use in the aerospace industry. Compared to metallic structures their behavior is less well understood. This lack of understanding may pose constraints on their use. One possible way to deal with some of the risks associated with potential failure is to perform in-situ monitoring to detect precursors of failures. Prognostic algorithms can be used to predict impending failures. They require large amounts of training data to build and tune damage model for making useful predictions. One of the key aspects is to get confirmatory feedback from data as damage progresses. These kinds of data are rarely available from actual systems. The next possible resource to collect such data is an accelerated aging platform. To that end this paper describes a fatigue cycling experiment with the goal to stress carbon-carbon composite coupons with various layups. Piezoelectric disc sensors were used to periodically interrogate the system. Analysis showed distinct differences in the signatures of growing failures between data collected at conditions. Periodic X-radiographs were taken to assess the damage ground truth. Results after signal processing showed clear trends of damage growth that were correlated to damage assessed from the X-ray images.

composites↗
NASA NTRS1993

Performance consequences of automation-induced 'complacency'

The effect of variations in the reliability of an automated monitoring system on human operator detection of automation failures was examined in two experiments. For four 30-min sessions, 40 subjects performed an IBM PC-based flight simulation that included manual tracking and fuel-management tasks, as well as a system-monitoring task that was under automation control. Automation reliability - the percentage of system malfunctions detected by the automation routine - either remained constant at a low or high level over time or alternated every 10 min from low to high. Operator detection of automation failures was substantially worse for constant-reliability than for variable-reliability automation after about 20 min under automation control, indicating that the former condition induced 'complacency'. When system monitoring was the only task, detection was very efficient and was unaffected by variations in automation reliability. The results provide the first empirical evidence of the performance consequences of automation-induced 'complacency'. We relate findings to operator attitudes toward automation and discuss implications for cockpit automation design.

Parasuraman, Raja↗
NASA NTRS2020

In-Flight Detection of Vibration Anomalies in Unmanned Aerial Vehicles

Owing to the frequency of occurrence and high risk associated with bearings, identification and characterization of bearing faults in motors via nondestructive evaluation (NDE) methods have been studied extensively, amongst which vibration analysis has been found to be a promising technique for early diagnosis of anomalies. However, a majority of the existing techniques rely on vibration sensors attached onto or in close proximity to the motor in order to collect signals with a relatively high SNR. Due to weight and space restrictions, these techniques cannot be used in unmanned aerial vehicles (UAVs), especially during flight operations since accelerometers cannot be attached onto motors in small UAVs. Small UAVs are often subjected to vibrational disturbances caused by multiple factors such as weather turbulence, propeller imbalance or bearing faults. Such anomalies may not only pose risks to UAV's internal circuitry, components or payload, they may also generate undesirable noise level particularly for UAVs expected to fly in low-altitudes or urban canyon. This paper presents a detailed discussion of challenges in in-flight detection of bearing failure in UAVs using existing approaches and offers potential solutions to detect overall vibration anomalies in small UAV operations based on IMU data.

Portia Banerjee↗
NASA NTRS1976

A dual-mode generalized likelihood ratio approach to self-reorganizing digital flight control system design

Analytic techniques have been developed for detecting and identifying abrupt changes in dynamic systems. The GLR technique monitors the output of the Kalman filter and searches for the time that the failure occured, thus allowing it to be sensitive to new data and consequently increasing the chances for fast system recovery following detection of a failure. All failure detections are based on functional redundancy. Performance tests of the F-8 aircraft flight control system and computerized modelling of the technique are presented.

Source record↗
NASA NTRS1985

Techniques for accommodating control effector failures on a mildly statically unstable airplane

Commercial airplanes are becoming increasingly more sophisticated, placing an increasing burden on pilots to detect and resolve the exhaustive set of possible control effector failures. Automatic techniques are needed to either reconfigure an existing control law or restructure a new control law after failure. A discrete control law has been designed for the longitudinal channel of a mildly statically unstable commercial airplane, to track the glideslope during the approach to landing phase of flight. Single effector failures with time delays for failure detection and identification are analyzed for both the reconfigured and restructured control laws, and results are compared with those from previous research using a statically stable airplane. Strategies considered include reconfiguration and restructuring with new flight conditions. Validation of all cases is made using a 6 DOF nonlinear airplane simulation.

Ostroff, A. J.↗
NASA NTRS1977

Elastrostatic-discharge damage to semiconductors

Failure mechanisms, test techniques, and quality control procedures for difficult-to-detect class of failures have been devised. Test circuit provides electrostatic discharge similar to those encountered in production situation and assists in evaluation of susceptibility of specific circuits and devices

Freeman, E. R., Jr.↗
NASA NTRS1988

Generating parity relations for detecting and identifying control system component failures

The monitoring of control system sensors and actuators for failures is presently undertaken by means of an exceptionally simple form of generalized parity relations based on a discrete-time model of the dynamics of linear, time-invariant systems. These generalized parity relations are constructed by recourse to a transfer matrix-description of the system that is additionally useful in the interpretation of their properties. Attention is given to a novel method for constructing the parity relation of minimum length that depends on the output of only a single sensor.

Vander Velder, Wallace E.↗
NASA NTRS1996

Effects of adaptive task allocation on monitoring of automated systems

The effects of adaptive task allocation on monitoring for automation failure during multitask flight simulation were examined. Participants monitored an automated engine status task while simultaneously performing tracking and fuel management tasks over three 30-min sessions. Two methods of adaptive task allocation, both involving temporary return of the automated engine status task to the human operator ("human control"), were examined as a possible countermeasure to monitoring inefficiency. For the model-based adaptive group, the engine status task was allocated to all participants in the middle of the second session for 10 min, following which it was again returned to automation control. The same occurred for the performance-based adaptive group, but only if an individual participant's monitoring performance up to that point did not meet a specified criterion. For the nonadaptive control groups, the engine status task remained automated throughout the experiment. All groups had low probabilities of detection of automation failures for the first 40 min spent with automation. However, following the 10-min intervening period of human control, both adaptive groups detected significantly more automation failures during the subsequent blocks under automation control. The results show that adaptive task allocation can enhance monitoring of automated systems. Both model-based and performance-based allocation improved monitoring of automation. Implications for the design of automated systems are discussed.

Task Performance and Analysis↗
NASA NTRS1989

SSME Propellant Path Leak Detection

The complicated high-pressure cycle of the space shuttle main engine (SSME) propellant path provides many opportunities for external propellant path leaks while the engine is running. This mode of engine failure may be detected and analyzed with sufficient speed to save critical engine test hardware from destruction. The leaks indicate hardware failures which will damage or destroy an engine if undetected; therefore, detection of both cryogenic and hot gas leaks is the objective of this investigation. The primary objective of this phase of the investigation is the experimental validation of techniques for detecting and analyzing propellant path external leaks which have a high probability of occurring on the SSME. The selection of candidate detection methods requires a good analytic model for leak plumes which would develop from external leaks and an understanding of radiation transfer through the leak plume. One advanced propellant path leak detection technique is obtained by using state-of-the-art technology infrared (IR) thermal imaging systems combined with computer, digital image processing, and expert systems for the engine protection. The feasibility of IR leak plume detection is evaluated on subscale simulated laboratory plumes to determine sensitivity, signal to noise, and general suitability for the application.

Roger Crawford↗
NASA NTRS1976

Electrostatic discharge in microcircuits

The largest number of electrostatic discharge (ESD) failures have occurred in linear microcircuits employing one or more MOS capacitors. The detection of ESD failures is considered. The phenomena involved in the generation of static charge are examined and a description is provided of approaches which can be used to protect microcircuits from ESD hazards. It is pointed out that ESD failures can virtually be eliminated if the procedural guidelines of protecting static-sensitive devices are implemented and conscientiously observed.

Trigonis, A. C.↗