Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TEMPERATURE DEPENDENCE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
NASA NTRS2001

Temperature Effects in Varactors and Multipliers

Varactor diode multipliers are a critical part of many THz measurement systems. The power and efficiencies of these devices limit the available power for THz sources. Varactor operation is determined by the physics of the varactor device and a careful doping profile design is needed to optimize the performance. Higher doped devices are limited by junction breakdown and lower doped structures are limited by current saturation. Higher doped structures typically have higher efficiencies and lower doped structures typically have higher powers at the same operating frequency and impedance level. However, the device material properties are also a function of the operating temperature. Recent experimental evidence has shown that the power output of a multiplier can be improved by cooling the device. We have used a particle Monte Carlo simulation to investigate the temperature dependent velocity vs. electric field in GaAs. This information was then included in a nonlinear device circuit simulator to predict multiplier performance for various temperatures and device designs. This paper will describe the results of this analysis of temperature dependent multiplier operation.

East, J.↗
NASA NTRS1998

Doubled CO2 Effects on NO(y) in a Coupled 2D Model

Changes in temperature and ozone have been the main focus of studies of the stratospheric impact of doubled CO2. Increased CO2 is expected to cool the stratosphere, which will result in increases in stratospheric ozone through temperature dependent loss rates. Less attention has been paid to changes in minor constituents which affect the O3 balance and which may provide additional feedbacks. Stratospheric NO(y) fields calculated using the GSFC 2D interactive chemistry-radiation-dynamics model show significant sensitivity to the model CO2. Modeled upper stratospheric NO(y) decreases by about 15% in response to CO2 doubling, mainly due to the temperature decrease calculated to result from increased cooling. The abundance of atomic nitrogen, N, increases because the rate of the strongly temperature dependent reaction N + O2 yields NO + O decreases at lower temperatures. Increased N leads to an increase in the loss of NO(y) which is controlled by the reaction N + NO yields N2 + O. The NO(y) reduction is shown to be sensitive to the NO photolysis rate. The decrease in the O3 loss rate due to the NO(y) changes is significant when compared to the decrease in the O3 loss rate due to the temperature changes.

Rosenfield, J. E.↗
NASA NTRS1990

Electrical transport measurements on polycrystalline superconducting Y-Ba-Cu-O films

The current-voltage, I-V, characteristics of polycrystalline Y-Ba-Cu-O films have been measured as a function of temperature. The I-V characteristics are interpreted using a model based upon an array of weak links with a statistical distribution of critical currents. In addition, evidence is found that the supercurrents flow in nearly independent filaments near Tc. Various criteria are discussed with respect to the definition of the transport critical current, Ic, in these films. A temperature dependence for Ic has also been deduced from the I-V data by appealing to an empirical scaling law. It is proposed that this temperature dependence is representative of the weaker links within the critical current distribution.

Stan, M. A.↗
NASA NTRS1986

Photo Hall-effect characterization of closely compensated Ge:Be

The temperature dependence of the free-carrier concentration in germanium doped with the double acceptor Be has been investigated using the photo Hall-effect technique and found to be strongly temperature dependent when the residual shallow impurities are closely compensated. Close compensation of shallow levels was achieved by controlling the concentration of a beryllium-hydrogen acceptor complex A(Be,H) which is present in crystals grown under a H2 atmosphere. This complex can be removed with high-temperature annealing. An increase of up to two orders of magnitude in free-carrier lifetime as a function of temperature is found to occur between 5 and 11 K in closely compensated material due to the population inversion of ionized centers created by optical pumping.

Germer, T. A.↗
NASA NTRS1987

Magnetic studies of high Tc superconducting (La0.9Sr0.1)2CuO4-y

The magnetic moment of La(0.9Sr0.1)2CuO4-y was measured as a function of temperature and magnetic field, and the onset of superconductivity was found to occur at a temperature of 35 K. At 2 K, the dc magnetic susceptibility was found to reach 83 percent of perfect diamagnetism. Field studies have shown that the sample is a type-II superconductor and that the temperature dependences of the critical fiedls are anomalous. Its critical fields, kappa, and lambda(eff) are much larger than those for (La0.9Ba0.1)2CuO4-y, and their temperature dependences cannot be explained in terms of BCS theory.

Zirngiebl, E.↗
NASA NTRS2003

New Examination of the Traditional Raman Lidar Technique II: Evaluating the Ratios for Water Vapor and Aerosols

In a companion paper, the temperature dependence of Raman scattering and its influence on the Raman and Rayleigh-Mie lidar equations was examined. New forms of the lidar equation were developed to account for this temperature sensitivity. Here those results are used to derive the temperature dependent forms of the equations for the water vapor mixing ratio, aerosol scattering ratio, aerosol backscatter coefficient, and extinction to backscatter ratio (Sa). The error equations are developed, the influence of differential transmission is studied and different laser sources are considered in the analysis. The results indicate that the temperature functions become significant when using narrowband detection. Errors of 5% and more can be introduced in the water vapor mixing ratio calculation at high altitudes and errors larger than 10% are possible for calculations of aerosol scattering ratio and thus aerosol backscatter coefficient and extinction to backscatter ratio.

Whiteman, David N.↗
NASA NTRS1983

Spatial variation of corn canopy temperature as dependent upon soil texture and crop rooting characteristics

A soil plant atmosphere model for corn (Zea mays L.) together with the scaling theory for soil hydraulic heterogeneity are used to study the sensitivity of spatial variation of canopy temperature to field averaged soil texture and crop rooting characteristics. The soil plant atmosphere model explicitly solves a continuity equation for water flux resulting from root water uptake, changes in plant water storage and transpirational flux. Dynamical equations for root zone soil water potential and the plant water storage models the progressive drying of soil, and day time dehydration and night time hydration of the crop. The statistic of scaling parameter which describes the spatial variation of soil hydraulic conductivity and matric potential is assumed to be independent of soil texture class. The field averaged soil hydraulic characteristics are chosen to be representative of loamy sand and clay loam soils. Two rooting characteristics are chosen, one shallow and the other deep rooted. The simulation shows that the range of canopy temperatures in the clayey soil is less than 1K, but for the sandy soil the range is about 2.5 and 5.0 K, respectively, for the shallow and deep rooted crops.

Choudhury, B. J.↗
NASA NTRS1992

Dependence of the cathodoluminescence of diamond films on deposition temperature

The deposition temperature dependence of the cathodoluminescence (CL) of diamond thin films grown by microwave-plasma-assisted chemical vapor deposition has been investigated. Depositions were made in the temperature range of 400 to 750 C at a pressure of 10 Torr, with a gas mixture of 5 percent CH4 and 5 percent O2 in hydrogen. The intensity of the luminescent peak at 430 nm was used as a measure of diamond quality for the film. This peak was found to be a maximum above 600 C. Examination of the intensities of CL emissions associated with nitrogen and silicon impurities at 530, 560, and 740 nm indicate incorporation of these impurities is more efficient at temperatures above 600 C. Film quality was thus found to be an optimization of competing mechanisms, i.e., improvement of diamond quality as evidenced by the intensity of the 430 nm peak, with the apparent activation of impurities and vacancy defects at elevated temperatures.

Shing, Y. H.↗
NASA NTRS1987

Comparative performance of diffused junction indium phosphide solar cells

A comparison is made between indium phosphide solar cells whose p-n junctions were processed by open tube capped diffusion, and closed tube uncapped diffusion, of sulfur into Czochralski grown p-type substrates. Air mass zero, total area, efficiencies ranged from 10 to 14.2 percent, the latter value attributed to cells processed by capped diffusion. The radiation resistance of these latter cells was slightly better, under 1 MeV electron irradiation. However, rather than being process dependent, the difference in radiation resistance could be attributed to the effects of increased base dopant concentration. In agreement with previous results, both cells exhibited radiation resistance superior to that of gallium arsenide. The lowest temperature dependency of maximum power was exhibited by the cells prepared by open tube capped diffusion. Contrary to previous results, no correlation was found between open circuit voltage and the temperature dependency of Pmax. It was concluded that additional process optimization was necessary before concluding that one process was better than another.

Weinberg, I.↗
NASA NTRS2006

Air-Broadening of H2O as a Function of Temperature: 696 - 2163 cm(exp -1)

The temperature dependence of air-broadened halfwidths are reported for some 500 transitions in the (000)-(000) and (010)-(000) bands of H2(16)O using gas sample temperatures ranging from 241 to 388 K. These observations were obtained from infrared laboratory spectra recorded at 0.006 to 0.011 cm(exp-1) resolution with the McMath-Pierce Fourier transform spectrometer located at Kitt Peak. The experimental values of the temperature dependence exponents, eta, were grouped into eight subsets and fitted to empirical functions in a semi-global procedure. Overall, the values of eta were found to decrease with increasing rotational quantum number J. The number of measurements (over 2200) and transitions (586) involved exceeds by a large margin that of any other comparable reported study.

Toth, R. A.↗
NASA NTRS1973

Excess junction current of silicon solar cells

The current-voltage characteristics of n(plus)-p silicon solar cells with 0.1, 1.0, 2.0, and 10 ohm-cm p-type base materials have been examined in detail. In addition to the usual I-V measurements, we have studied the temperature dependence of the slope of the I-V curve at the origin by the lock-in technique. The excess junction current coefficient (Iq) deduced from the slope at the origin depends on the square root of the intrinsic carrier concentration. The Iq obtained from the I-V curve fitting over the entire forward bias region at various temperatures shows the same temperature dependence. This result, in addition to the presence of an aging effect, suggest that the surface channel effect is the dominant cause of the excess junction current.

Wang, E. Y.↗
NASA NTRS1981

Muon hyperfine fields in iron and its dilute alloys

The temperature dependence of the interstitial magnetic field, B, as determined by the rotation of the spin of the muon, has been measured for dilute polycrystalline iron alloys with Mo, Ti, and Nb additions over a temperature range of 240 to 633 K. In all cases the behaviors differ from one another and from the Fe(Al) alloys previously studied. B, which is negative with respect to the magnetization, is increased in magnitude by Al and Mo, and decreased greatly by Ti. The addition of Nb creates a two-phase alloy from which the role of heterogeneity and/or strain on B in iron can be assessed. If the temperature dependence of the hyperfine field extracted from B for Fe(Mo) alloys is interpreted on the model previously used to discuss the Fe(Al) data, then the muon must be attracted to the Mo atom while repelled by the Al atoms as the temperature decreases.

Stronach, C. E.↗
NASA NTRS2007

High-Temperature Properties of Piezoelectric Langatate Single Crystals

Langasite type crystals belong to non-polar point group of 32 and do not show any phase transformations up to the melting temperature. Langatate (La3Ga(5.5)Ta(0.5)O14) demonstrates piezoelectric activity better than quartz and possesses attractive properties for high temperature sensors, resonators and filter applications. High-quality and colorless langatate crystals were grown by the Czochralski technique. The electromechanical and electrical properties of langatate crystals in different crystallographic directions were characterized at elevated temperature. The piezoelectric coefficient along x-axis was 7 pC/N as measured by a Berlincourt meter for a plate geometry with an aspect ratio of 10:1. The dielectric constant did not exhibit any significant temperature dependence (K33 approx. 21 at 30 C and K33 approx. 23 at 600 C). Loss tangent at 100 kHz remained <0.003 up to 300 C and <0.65 at 600 C. The dielectric properties along the y-axis were similar and its temperature dependence was analogous to the x-axis. Electromechanically, the inactive z-axis exhibited no resonance with K33 approx. 84 at room temperature, decreasing down to approx. 49 at 600 C. Resistivity of these crystals along x-axis decreased from approx. 6x10(exp 11) omega-cm at room temperature, to approx. 1.6x10(exp 6) omega-cm at 600 C.

Sehirlioglu, Alp↗
NASA NTRS1982

Shock tube measurements of growth constants in the branched chain formaldehyde-carbon monoxide-oxygen system

Exponential free radical growth constants were measured for formaldehyde carbon monoxide-oxygen systems by monitoring the growth of oxygen atom concentration as manifested by CO flame band emission. Data were obtained over the temperature range of 1200 to 2000 K. The data were analyzed using a formaldehyde oxidation mechanism involving 12 elementary reaction steps. The computed growth constants are roughly in accord with experimental values, but are much more temperature dependent. The data was also analyzed assuming formaldehyde is rapidly decomposed to carbon monoxide and hydrogen. Growth constants computed for the resulting carbon monoxide hydrogen oxygen mixtures have a temperature dependence similar to experiments; however, for most mixtures, the computed growth constants were larger than experimental values.

Brabbs, T. A.↗
NASA NTRS2015

Analytic Thermoelectric Couple Modeling: Variable Material Properties and Transient Operation

To gain a deeper understanding of the operation of a thermoelectric couple a set of analytic solutions have been derived for a variable material property couple and a transient couple. Using an analytic approach, as opposed to commonly used numerical techniques, results in a set of useful design guidelines. These guidelines can serve as useful starting conditions for further numerical studies, or can serve as design rules for lab built couples. The analytic modeling considers two cases and accounts for 1) material properties which vary with temperature and 2) transient operation of a couple. The variable material property case was handled by means of an asymptotic expansion, which allows for insight into the influence of temperature dependence on different material properties. The variable property work demonstrated the important fact that materials with identical average Figure of Merits can lead to different conversion efficiencies due to temperature dependence of the properties. The transient couple was investigated through a Greens function approach; several transient boundary conditions were investigated. The transient work introduces several new design considerations which are not captured by the classic steady state analysis. The work helps to assist in designing couples for optimal performance, and also helps assist in material selection.

Seebeck Effect↗
NASA NTRS1992

CN radical reactions with hydrogen cyanide and cyanogen - Comparison of theory and experiment

The method of laser photolysis/laser-induced fluorescence is used to obtain absolute rate constants for CN radical reactions with HCN and C2N2. The rate constants were found to be temperature-dependent in the range 300-740 K and pressure independent in the range 100-600 Torr. Rice-Remsperger-Kassel-Marcus theory for both reactions employing the transition state parameters obtained by the BAC-MP4 method are made. These calculations yielded reasonable results for the CN + HCN reaction, predicting both the temperature dependence and pressure independence. No pressure effect was observed in the pressure range 100-1000 Torr at temperatures below 900 K, confirming the experimental results.

Yang, D. L.↗
NASA NTRS1990

Enhanced ultrasonic attenuation of Tl-Ca-Ba-Cu-O at the superconducting transition

Temperature-dependent ultrasonic attenuation measurements have been performed on polycrystalline samples of Tl-Ca-Ba-Cu-O at various frequencies. An attenuation anomaly was observed close to the superconducting transition temperature T(c) (103 K) whose temperature position was frequency-independent. The attenuation decreased exponentially with temperature in the superconducting state for both transverse and longitudinal waves. It was also found that the temperature-dependent sound velocity showed a slope change around T(c).

Sun, K. J.↗
NASA NTRS1998

Thermal Effects Modeling Developed for Smart Structures

Applying smart materials in aeropropulsion systems may improve the performance of aircraft engines through a variety of vibration, noise, and shape-control applications. To facilitate the experimental characterization of these smart structures, researchers have been focusing on developing analytical models to account for the coupled mechanical, electrical, and thermal response of these materials. One focus of current research efforts has been directed toward incorporating a comprehensive thermal analysis modeling capability. Typically, temperature affects the behavior of smart materials by three distinct mechanisms: Induction of thermal strains because of coefficient of thermal expansion mismatch 1. Pyroelectric effects on the piezoelectric elements; 2. Temperature-dependent changes in material properties; and 3. Previous analytical models only investigated the first two thermal effects mechanisms. However, since the material properties of piezoelectric materials generally vary greatly with temperature (see the graph), incorporating temperature-dependent material properties will significantly affect the structural deflections, sensory voltages, and stresses. Thus, the current analytical model captures thermal effects arising from all three mechanisms through thermopiezoelectric constitutive equations. These constitutive equations were incorporated into a layerwise laminate theory with the inherent capability to model both the active and sensory response of smart structures in thermal environments. Corresponding finite element equations were formulated and implemented for both the beam and plate elements to provide a comprehensive thermal effects modeling capability.

Lee, Ho-Jun↗