SEARCH · Engineering Papers

Results for “Conducting polymers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

All sources NASA NTRS DOE OSTI

DOE OSTI2022

Selective Plasticization of Poly (ethylene oxide) (PEO) Block in Nanostructured Polystyrene– PEO– Polystyrene Triblock Copolymer Electrolytes

The plasticization of a polymer electrolyte usually promotes its ionic conductivity but decreases its storage modulus due to the increased polymer chain flexibility. Herein, we show that such a tradeoff between the ionic conductivity and the mechanical robustness of the polymer electrolyte can be alleviated by selective plasticization of the ion-conductive block, such as poly(ethylene oxide) (PEO) in a polystyrene (PS)– PEO–PS block copolymer (SEO) electrolyte using an ether type plasticizer, tetraethylene glycol dimethyl ether (TEGDME). In this work, at maximum plasticizer loading, the room temperature ionic conductivity increases by up to 3 orders, whereas the storage modulus, G' reduces to half, is still on the order of 10 2 MPa. At above the melting temperature of the PEO block, the dynamic storage modulus, G' of the plasticized membrane surpasses its dry PS-PEO-PS counterpart. Such a phenomenon results from that, a) TEGDME co-crystallizes with PEO to promote its crystallinity and hence the storage modulus, b) TEGDME swells the amorphous PEO phase to enhance the polymer chain segmental mobility and hence ionic conductivity, and c) the PS phase remains intact from TEGDME to keep the SEO elastic.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS2006

Electrical Conductivity in Textiles

Copper is the most widely used electrical conductor. Like most metals, though, it has several drawbacks: it is heavy, expensive, and can break. Fibers that conduct electricity could be the solutions to these problems, and they are of great interest to NASA. Conductive fibers provide lightweight alternatives to heavy copper wiring in a variety of settings, including aerospace, where weight is always a chief concern. This is an area where NASA is always seeking improved materials. The fibers are also more cost-effective than metals. Expenditure is another area where NASA is always looking to make improvements. In the case of electronics that are confined to small spaces and subject to severe stress, copper is prone to breaking and losing connection over time. Flexible conductive fibers eliminate that problem. They are more supple and stronger than brittle copper and, thus, find good use in these and similar situations. While clearly a much-needed material, electrically conductive fibers are not readily available. The cost of new technology development, with all the pitfalls of troubleshooting production and the years of testing, and without the guarantee of an immediate market, is often too much of a financial hazard for companies to risk. NASA, however, saw the need for electrical fibers in its many projects and sought out a high-tech textile company that was already experimenting in this field, Syscom Technology, Inc., of Columbus, Ohio. Syscom was founded in 1993 to provide computer software engineering services and basic materials research in the areas of high-performance polymer fibers and films. In 1999, Syscom decided to focus its business and technical efforts on development of high-strength, high-performance, and electrically conductive polymer fibers. The company developed AmberStrand, an electrically conductive, low-weight, strong-yet-flexible hybrid metal-polymer YARN.

Source record↗

NASA NTRS1994

Photocured Gelled Electrolytes For Secondary Li Cells

Class of photocured polymers exhibiting lithium-ion conductivities greater than those of well-studied polymers based on polyethylene oxide (PEO) show promise as polymeric electrolytes in rechargeable lithium cells. Increase in conductivity occasioned by use of electrolytes, coupled with amenability of electrolytes to formation into uniform thin (less than 25 micrometers thick), wide films, expected to result in cells with power densities greater than 100 W h/kg and charge/discharge rates exceeding currents equal, in amperes, to ampere-hour ratings. All-solid-state lithium batteries containing these electrolytes used as high-power, high-rate rechargeable power sources in commercial and aerospace applications.

Nagasubramanian, Ganesan↗

DOE OSTI2025

Lightweight, Flexible Electromagnetic Shielding Composite Films Reinforced with Recycled Carbon Fibers and Carbon Nanofillers

Lightweight, flexible polymer composites are widely adopted in modern electronic devices and systems for high-efficiency electromagnetic interference (EMI) shielding. Reinforcing polymer composites with conductive fillers offers a promising alternative to conventional metal-based shielding material thanks to their low density, tunable properties, and flexibility. Herein, lightweight, flexible ultra-high molecular weight polyethylene composite films reinforced with recycled carbon fibers (rCFs) and carbon-based nanofillers, including graphene nanoplatelets (GNPs) and carbon nanotubes, are reported for EMI shielding applications. The incorporation of these nanofillers significantly reduces the required content of rCFs and improves processability while maintaining comparable shielding effectiveness. The addition of these nanofillers with rCFs enhances the EMI shielding effectiveness by up to 15 dB. Incorporating 1 wt% GNPs can replace 5 wt% rCFs and achieve comparable EMI shielding performance, while 5 wt% of either nanofillers can substitute for 10 wt% rCFs. Numerical modeling of electromagnetic wave transmission reveals that increasing nanofiller concentrations enhances both reflection and absorption losses, with absorption consistently dominating across all levels. Furthermore, this study not only provides insight into the synergistic contributions of rCFs and carbon nanofillers to shielding effectiveness but also paves the way for the design of sustainable, lightweight EMI shielding composite films for applications in electric vehicles, medical equipment, and portable electronics.

carbon nanofiller↗

DOE OSTI2020

Dichlorinated Dithienylethene-Based Copolymers for Air-Stable n-Type Conductivity and Thermoelectricity

Here, two donor-acceptor polymers were obtained by coupling difluoro- and dichloro-substituted forms of the electron-deficient unit BDOPV and the relatively weak donor moiety dichlorodithienylethene (ClTVT). The conductivity and power factors of doped devices are different for the chlorinated and fluorinated BDOPV polymers. High electron conductivity of 38.3 and 16.1 S cm -1 were obtained from the chlorinated and fluorinated polymers with N-DMBI, respectively, and 12.4 and 2.4 S cm -1 were obtained from the chlorinated and fluorinated polymers with CoCp 2 , respectively, from drop-cast devices. The corresponding power factors are 22.7, 7.6, 39.5 and 8.0 μW m -1 K -2 , respectively. Doping of PClClTVT with N-DMBI results in excellent air-stability; the electron conductivity of devices with 50 mol% N-DMBI as dopant remained up to 4.9 S m -1 after 222 days in the air, the longest for an n-doped polymer stored in air, with a thermoelectric power factor of 9.3 μW m -1 K -2 . However, the conductivity of PFClTVT-based devices can hardly be measured after 103 days. These observations are consistent with morphologies determined by grazing incidence wide angle X-ray scattering (GIWAXS) and atomic force microscopy (AFM). The results demonstrate that chemical structures leading to dense and ordered packing can enhance electron conductivity and air stability of n-type donor-acceptor polymers.

30 DIRECT ENERGY CONVERSION↗

DOE OSTI2022

Tin sensitization and silver activation on indium tin oxide surfaces

Adhesion of electrical contacts on electronic and optoelectronic devices is important for reliable device operation. Sn-sensitization is a widely used process that improves uniformity and adhesion of plated metals to glass and polymer surfaces. Electrically conductive substrates can significantly benefit from improved uniformity, adhesion, and contact resistance to metallic contact layers. In this study, we investigate the process of Sn-sensitization and Ag-activation on indium tin oxide (ITO) surfaces—a dominant transparent conducting oxide used in optoelectronic devices. Here, our results show that ITO films exposed to Sn-sensitization solutions with HCl concentrations below 10 mM effectively modify the surface termination through the process of Sn-sensitization (Sn-bonding at the surface hydroxide sites) without etching the ITO film. However, the subsequent Ag-activation on an ITO surface does not seem to follow the typical response on a glass substrate, suggesting that Ag-activation of an ITO surface is likely limited by the Ag ion size relative to the area density of surface hydroxide sensitization sites.

42 ENGINEERING↗

DOE OSTI2021

Modeling of crystallization fouling on a horizontal-tube falling-film evaporator for thermal desalination

Scale formation within horizontal-tube falling-film evaporators is an important issue for thermal desalination, because of the deterioration of heat transfer performance and added maintenance costs. Predicting the fouling process is crucial for desalination plant design, operation, and maintenance. In this paper, a model is developed to predict the crystallization fouling process during seawater falling-film flow over a horizontal tube bundle. The scaling is estimated based on deposition theory, with couple heat transfer including the in-tube steam condensation, conduction through the tube wall and the scale layer, and falling-film evaporation. The spatial and temporal variations of temperature, heat transfer coefficient, and scale thickness are predicted, and the effects of variations in process parameters of steam, feed seawater, and tube properties on the scale thickness, evaporation rate, and heat transfer coefficient for falling-film evaporation are analyzed. Comparisons to existing experimental data show the scaling layer thickness falls in the general range of reported measurements, with a slight overestimation due to neglecting the delay of scaling onset under real conditions. The scale layer thickness increases dramatically as the in-tube steam pressure is increased or the seawater flow rate is decreased. In general, the scaling layer becomes thicker on the lower tubes in the tube bundle, due to the heat and mass transfer of the falling film. The effect of tube material on scaling appears mainly dependent on thermal conductivity; thus, using polymer rather than a stainless steel tube decreases scaling and evaporation rate 96% and 88%, respectively. Finally, this work has potential to guide thermal desalination plant design, material selection, and operating parameter optimization.

42 ENGINEERING↗

DOE OSTI2025

Interface-engineered (AlMnCoNiZn) 3 O 4 @PPy nanocomposites for superior lithium storage: Mechanism and performance

The practical application of graphite anodes in lithium-ion batteries (LIBs) is constrained by low specific capacity (372 mAh g -1 ) and sluggish kinetics. Here, to address these limitations, our present study focuses on high-entropy oxides (HEOs), which offer high theoretical capacity and structural stability. We synthesized spinel-structured (AlMnCoNiZn) 3 O 4 nanoparticles via a solution combustion method and fabricated an (AlMnCoNiZn) 3 O 4 @polypyrrole (PPy) nanocomposite through in-situ polymerization. Our electrochemical tests demonstrate that the PPy modification significantly enhances performance. While the pristine (AlMnCoNiZn) 3 O 4 delivered 445 mAh g −1 after 100 cycles at 100 mA g −1 and 350 mAh g −1 after 1000 cycles at 1000 mA g −1 , the (AlMnCoNiZn) 3 O 4 @PPy composite achieved 695 mAh g −1 after 100 cycles and maintained 675 mAh g −1 after 1000 cycles. Furthermore, the composite improved rate capacity at 1000 mA g −1 from 211 mAh g −1 to 403 mAh g −1 . This work highlights how conductive and flexible polymer modifications can dramatically improve the electrochemical properties of HEOs. The developed (AlMnCoNiZn) 3 O 4 @PPy composite provides a promising direction for designing advanced anodes to meet next-generation energy storage demands.

Anodes material↗

DOE OSTI2024

Structure–performance relationships of lithium-ion battery cathodes revealed by contrast-variation small-angle neutron scattering

Lithium-ion battery cathodes are porous composites of active material, conductive carbon, and polymer binder. Controlling the cathode microstructure is key to achieving high energy density and cycling stability. Current characterization techniques lack the nanoscale resolution over representative volumes necessary to relate cathode microstructure to cycling performance. To address this challenge, we utilize contrast-variation small-angle neutron scattering to quantify the chemical and structural features of cathodes wet by dimethyl carbonate, representing a relevant solvent environment. Using neutron scattering measurements, we identify an expansion in carbon and polymer structures that arises after calendering and wetting with solvent. Further, we deconvolute the carbon and binder phases to obtain the solvent-accessible carbon black surface area, which we correlate to diminished capacity retention driven by electrolyte decomposition on exposed carbon. This technique provides nanoscale insight into composite cathode microstructures and resulting cycling performance, promising future applications to a broad range of porous materials that exist in energy storage systems.

25 ENERGY STORAGE↗

DOE OSTI2022

Air-to-Liquid Heat Exchanger Fabricated Using Deposition-Based Additive Manufacturing Processes

Abstract This work describes the use of deposition-based additive manufacturing (AM) techniques to fabricate air-cooled, two-fluid heat exchangers. The project focused on a Heating, Ventilation and Air Conditioning application and used an industry-standard copper/aluminum heat exchanger manufactured with conventional technology as the basis for assessing performance. The manufacturing constraints associated with using deposition-based AM technology for this application include the need for a continuous tool path within each build layer that allows uninterrupted extrusion and therefore defect-free water channel walls that correspond to a reliably leak-tight heat exchanger. A geometry that respects these constraints was developed, simulated, optimized and finally manufactured and tested. The material used was a composite of polymer filled with conductive flakes in order to provide high conductivity in the direction that heat must flow in this heat exchanger, across the wall separating the fluids. The measured performance for several test coupons matched the predicted performance and the test coupons exhibited performance that approach and in some cases exceeds conventional technology

Engineering↗

NASA NTRS1975

Synthesis and development of low cost, high temperature N-arylene polybenzimidazole foam material

Polymer (and foam) studies followed two basic routes: (1) formation of high molecular weight uncyclized polyamide followed by subsequent fusion and cyclodehydration to yield NABI (foam) and (2) polymer and foam formation by reaction of diphenyl esters (or anhydrides) with the tetramine. The latter route was found much more attractive since considerable versatility in both basic polymer structure and crosslinkability is achievable. Preliminary studies on BAB, phthalic anhydride (PA), and 3, 3 (prime), 4, 4(prime) benzo pheno netetracarboxylic acid dianhydride (BTDA) as crosslinked polymer precursors were conducted. Nonmelting rigid char forming foams with densities as low as 2.7 lb/cubic ft. were achieved. The program was successful in the preparation of a potentially low cost, low density, high char yield, high temperature foam material.

Harrison, E. S.↗

NASA NTRS1977

The physics of gridded and conductive coated dielectrics for spacecraft

Theoretical aspects of electrostatic control and design of gridded and conductive film bonded polymers, for spacecraft Thermo-optical blankets are considered. Brief commentaries relative to the salient features of the primarily developed facility for and characterization of said polymers is also considered.

Okress, E. C.↗

NASA NTRS1983

Synthesis and thermal stability of carborane containing phosphazenes

Carborane substituted polyphosphazenes were prepared by the thermal polymerization of phenyl-carboranyl penta chlorocyclotriphosphazene. Successive isothermal vacuum pyrolyses were conducted on the polymer and examined for structural changes by infrared spectroscopy. The degradation products were ascertained by gas chromatography-mass spectrometric analysis. It was found that the presence of the carborane group improves the thermal stability of the polymer by retarding the ring chain equilibrium processes of decomposition.

Fewell, L. L.↗

NASA NTRS1983

Synthesis and thermal stability of carborane-containing phosphazenes

Carborane-substituted polyphosphazenes were prepared by the thermal polymerization of phenyl-carboranyl pentachlorocylotriphosphazene. Successive isothermal vacuum pyrolyses were conducted on the polymer and examined for structural changes by infrared spectroscopy. The degradation products were ascertained by gas chromatography-mass spectrometric analysis. It was found that the presence of the carborane group improves the thermal stability of the polymer by retarding the ring-chain equilibrium processes of decomposition. Previously announced in STAR as A83-21034

Fewell, L. L.↗

NASA NTRS1992

Orbital transfer rocket engine technology program: Soft wear ring seal technology

Liquid oxygen (LOX) compatibility tests, including autogenous ignition, promoted ignition, LOX impact tests, and friction and wear tests on different PV products were conducted for several polymer materials as verification for the implementation of soft wear ring seals in advanced rocket engine turbopumps. Thermoplastics, polyimide based materials, and polyimide-imide base materials were compared for oxygen compatibility, specific wear coefficient, wear debris production, and heat dissipation mechanisms. A thermal model was generated that simulated the frictional heating input and calculated the surface temperature and temperature distribution within the seal. The predictions were compared against measured values. Heat loads in the model were varied to better match the test data and determine the difference between the measured and the calculated coefficients of friction.

Lariviere, Brian W.↗

NASA NTRS1993

Method of continuously determining crack length

The determination of crack lengths in an accurate and straight forward manner is very useful in studying and preventing load created flaws and cracks. A crack length sensor according to the present invention is fabricated in a rectangular or other geometrical form from a conductive powder impregnated polymer material. The long edges of the sensor are silver painted on both sides and the sensor is then bonded to a test specimen via an adhesive having sufficient thickness to also serve as an insulator. A lead wire is connected to each of the two outwardly facing silver painted edges. The resistance across the sensor changes as a function of the crack length in the specimen and sensor. The novel aspect of the present invention includes the use of relatively uncomplicated sensors and instrumentation to effectively measure the length of generated cracks.

Prabhakaran, Ramamurthy↗

NASA NTRS1987

Lanthanide-containing polyimides

The preparation of a variety of lanthanide-containing polyimide films is described, and results of their characterization are presented. The properties investigated include the glass transition temperature, thermooxidative stability, magnetic susceptibility, and electrical conductivity of the polymer. Films containing lanthanide chlorides, fluorides, and sulfides are flexible, but those containing lanthanide nitrates are extremely brittle. The addition of lanthanide acetates and acetylacetonates caused immediate gelation of two of the synthesis-mixture ingredients. It was found that, in general, the addition of lanthanide to the polyimide increases the density and glass transition temperature of the polymer but slightly decreases the thermooxidative stability.

Stoakley, D. M.↗

NASA NTRS2007

Flexible carbon-based ohmic contacts for organic transistors

The present invention relates to a system and method of organic thin-film transistors (OTFTs). More specifically, the present invention relates to employing a flexible, conductive particle-polymer composite material for ohmic contacts (i.e. drain and source).

Brandon, Erik↗