Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “high temperature operation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Investigation of defects in melt and solution grown perovskite CsPbBr 3 single crystals

Recently, there has been considerable interest in x-ray and gamma ray detectors with large volume and high energy resolution that operate at room temperature. To improve detector energy resolution, the carrier mobility-lifetime product needs to be increased, and the electronic trap state concentration needs to be minimized. Defect concentrations in the part per billion range can alter the charge transport and carrier recombination lifetime. In this work, thermally stimulated current spectroscopy measurements were systematically carried out in bulk halide perovskite single crystals of CsPbBr 3 over a temperature range of 80–320 K. The origins and trap parameters of CsPbBr 3 crystals from the solution growth and melt growth procedures were determined and compared. Trap concentrations were ranged from 1 × 10 11 to 1 × 10 16 cm –3 . Appreciable detector performance was observed for CsPbBr3 crystals with trap concentrations less than 1 × 10 14 cm –3 . The comparison of spectral responses of crystal samples grown using two different methods shows that, after purification, solution-grown crystals are comparable to melt-grown crystals in terms of low defect concentration and improved detector performance. Finally, for an improved mobility-lifetime product and enhanced spectral response to high energy radiation from fissile materials, trap states in either type of a crystal ingot must be reduced closer to 10 11 cm –3 .

36 MATERIALS SCIENCE↗
DOE OSTI2022

Water-gas shift reaction in ceramic-carbonate dual-phase membrane reactor at high temperatures and pressures

Water-gas-shift (WGS) reaction is a critical step in integrated gasification combined cycles (IGCC) power plants with CO 2 capture. Membrane reactors made with a CO 2 -permselective ceramic-carbonate dual-phase (CCDP) membrane offers the potential to enhance hydrogen yield with simultaneous CO 2 capture for WGS reaction. The present work studies operation of WGS reaction in a tubular membrane reactor made of samarium-doped ceria infiltrated with lithium/sodium molten carbonate mixture. The WGS reaction was performed in the membrane reactor with and without a high-temperature WGS catalyst at 800–850 °C, feed pressure of 7 bar, the space velocity of 150–3000 h –1 , and a feed gas mixture of 45.7/13.1/41.3 mol% CO/CO 2 /N 2 with steam to carbon ratio of 4. The results show that the catalyst-free membrane reactor can convert 92% of carbon monoxide into CO 2 and H 2 and recover 29% CO 2 at 850 °C and a space velocity of 150 h –1 . However, in the catalyst-free membrane reactor, a significant amount of unwanted carbon deposition is observed. The side reactions can be minimized by reducing the operating pressure and increasing the operating temperature and space velocity, and completely avoided using a high-temperature catalyst at space velocity>500 h –1 . The membrane reactor with a WGS catalyst achieves CO conversion of about 85%, above the equilibrium conversion, and 40% CO 2 recovery without carbon deposition at high temperature and pressure. Finally, the membrane remains in the same structure and gas-tightness after the WGS reaction tests.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2021

Highly Integrated Wide Bandgap Power Module for Next Generation Plug-In Vehicles (Final Report)

Wide bandgap devices are key enablers for high power density traction inverters. A highly integrated wide bandgap (WBG) power module enables higher temperature operation, higher inverter efficiency and overall smaller die area with the same power delivery. However, it requires careful design of the power module to take advantage of all the superior material properties that silicon carbide (SiC) provides over conventional silicon (Si) Insulated Gate Bipolar Transistor (IGBT) based design. This project developed an efficient and densely packed SiC power module for an automotive traction inverter application. Extensive study was performed to select the best performing SiC die considering a wide range of temperature variation, suitability to integrate into target packaging, robust body diode performance and overall high electrical efficiency. Multiple design ideas were explored to achieve lower stray inductance for both power loop and signal loop, uniform current distribution, compact form factor, and very high thermal performance. The final power module package includes all six inverter switches in the same module (six-pack) with die sintered at both bottom and top surfaces utilizing high performance substrate to achieve high electrical and thermal performance. Two power module variants were developed using 900 V and 1200 V devices for operating at two different high voltage levels (> 600 V HV battery). Both power modules were comprehensively characterized, and high efficiency operation of the inverter was confirmed through analysis. Finally, a complete functional inverter was built with the 1200V power modules using other essential components (HV capacitors, gate driver board, controller board, current sensor, connectors etc.) and tested using GM’s standard test procedure. There are several challenges associated with adopting WBG devices for high voltage operation. In order to assess and mitigate those challenges, GM and subrecipients of this project have conducted multiple detailed studies. This includes phase current reconstruction using integrated Rogowski coil, device junction temperature estimation using on-state gate resistance, modeling and testing the effect of high voltage and fast switching on motor insulation and bearings, partial discharge inception voltage measurement under different environmental conditions. Findings of all these studies are summarized in this report.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2023

Research tool development for catalyst, catalyst/ionomer, and ionomer characterization above 100°C (CRADA Final Report)

There is a need to develop experimental tools that address the catalyst and ionomer interface under high-temperature proton-exchange-membrane (HT-PEM) operating conditions (dry, >100°C). These conditions mean traditional water-based measurements for membrane and ionomer properties are insufficient; new ex-situ techniques are required to address and characterize expected novel materials. In this project we develop a microelectrode cell for high temperature kinetics and gas transport properties and ex-situ ionomer thin-film characterization under these conditions. We use baseline Nafion and phosphoric-acid imbibed membranes as prototype materials for measuring the membrane/acid/ionomer systems with Pt microelectrodes and demonstrate feasibility of the tools.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Regulatory Considerations Regarding Potential High Temperature Fluid Releases in Advanced Reactor Designs

The current effort is supported by the U.S. Department of Energy (DOE), Advanced Reactor Demonstration Program (ARDP) Regulatory Development, Regulatory Framework Modernization area, which seeks to address potential regulatory challenges for advanced reactor vendors that are currently or will soon be initiating the licensing process. In pursuit of this goal, this effort seeks to aid the advanced reactor industry and regulatory bodies in understanding and addressing the potential occurrence of high-temperature fluid releases in advanced reactor designs as part of licensing and regulatory oversight of operation. Improving the awareness and understanding of the behavior and potential consequences associated with high-temperature fluid release events can ensure that they are appropriately considered and addressed.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

ULTIMATE Phase I project: Development of Niobium-based alloys for Turbine Applications

Current Ni-based alloys used in turbine blade applications are operating at 1100°C which is approximately 90% of the solidus of Ni-based alloys. Further increases in temperature can be achieved only through the use of alloys with higher solidus temperatures such as refractory alloys which include Mo, Nb, W, Ta alloys. Niobium has a unique combination of physical properties that include a high melting point (2468°C), lowest density (8.57 g/cc), and the lowest modulus amongst refractory alloys, a good thermal conductivity that increases from 45 W/mK at room temperature to 62 W/mK at 1093°C, good ductility with fabricability using traditional techniques, high strength, good creep resistance, and general chemical inactivity. Hence niobium alloys offer many advantages for use at the desired temperature of 1300°C. One of the major deterrents to the use of niobium and its alloys at high temperatures is achieving good oxidation resistance. In addition, achieving balanced properties of room temperature strength, ductility, fracture toughness, high temperature strength, and creep resistance required for 1300°C operation at a density of 9 g/cm 3 is extremely challenging since the addition of W which is a potent strengthener increases the density of the alloy. This project seeks to enable the development of a tri-layered turbine blade that can operate continuously at 1300°C with the core of the turbine blade providing good creep resistance, the second layer providing improved oxidation resistance over the core layer, and the third layer being an environmental barrier providing oxidation resistance. The objective of this Phase 1 project was to use computational modeling and advanced characterization tools to develop two classes of Nb alloys which could be used as the core layer and the transition layer. The first class of alloys developed in this project was a Nb-alloy designed to serve as the turbine blade core with excellent room temperature strength, ductility, and high temperature strength and creep resistance required for 1300°C operation. These alloys were designed to contain sufficient solute solution strengthening elements (W, Mo) but constrained by the density of alloy, along with the addition of elements such as Zr, Hf, Ta, C, and N to achieve a combination of primary and secondary carbide precipitation. A total of 38 “creep-resistant” alloys were designed and cast during the duration of the project. Processing techniques were developed to keep the oxygen contents as low as possible with typical oxygen contents less than 250 ppm. One alloy with a density of < 9.5 g/cc was successful in meeting the Phase 2 intermediate project mechanical property milestone requirements of room temperature ductility greater than 1.0%, 1200°C creep strain of less than 3% at 150 MPa and 100 hours in vacuum, and with solidus temperature greater than 1500ᵒC. The second class of alloys was designed to be a Nb-rich alloy with improved oxidation resistance when compared to the core layer and was designed specifically to be compatible with the core layer and the outer environmental barrier coating. This Nb- alloy will be specifically designed to be microstructurally stable at these temperatures when in contact with the core alloy and provide protection against catastrophic failure of the barrier coating. Two alloys were cast and processed but further development was discontinued to focus on the development of the creep resistant alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Analysis of buffer-IPyC separation in TRISO fuel particles

During High Temperature Gas-cooled Reactor (HTGR) operation, and due to the neutron irradiation in the reactor core, damage of the nuclear fuel coating layers occurs. The mechanism of damage formation in the TRISO fuel is explored by the Advanced Gas Reactor (AGR) Fuel Development and Qualification Program, in which the debonding process between coating layers was also investigated. The purpose of this paper is to report simulation results for two models. Firstly, the debonding restricted model, where no gap formation between buffer and IPyC layers is permitted. Secondly, a debonding enabled model, where the gap between those layers is created. The simulations were performed with the Bison code. The inputs of the simulated models are based on data from the AGR-1 experiment. Further, the research included simulations on spherical and aspherical fuel types. The simulations match results obtained by the AGR-1 experiment, which as such shows that the Bison code is a good computational method for simulating the behavior of the gap between buffer and IPyC layers in TRISO fuel. Based on the irradiation experiments, and the Bison simulations, it was concluded that the most common scenario is a gap formation along the buffer-IPyC interface, while the least possible scenario is the situation where there is no gap formation at the buffer-IPyC junction. The computational results confirmed that the sphericity of the fuel influences the thickness of the gap that occurs at the buffer-IPyC junction, in a way that with increasing aspect ratio the gap thickness increases. In addition, the fuel sphericity does not influence the Weibull failure probability. The results obtained for spherical and aspherical fuel are nearly identical.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Measurement of Helium and Xenon Knudsen permeability in graphite IG-11

Here, understanding the flow and diffusion (transport) of gases through nuclear graphite is of interest in both the prismatic and pebble bed high-temperature gas reactors (HTGRs), for normal operation and under accident conditions, for example, as related to graphite oxidation. Both the laminar and turbulent gaseous transport are of interest. It has also been noted that nuclear graphite can have pore sizes that can possibly lead to non-continuum transport, as the pore size can be comparable to the gaseous mean free path. We report measurements and analyzes of experiments performed with IG-11 graphite in the pressure range of 10 Pa to 14,700 Pa, 293 K, using Helium, and research grade xenon (99.999%), respectively. These values are in fair agreement with those reported for different graphites and gases by other investigators, but are also higher by six orders of magnitude than those reported for Kr permeability in a developmental very low permeability graphite-HXT-90. Our measured ratio of the Helium and Xenon permeabilities is about 4, different from $\sqrt{\frac{m_{Xe}}{m_{He}}}$ ≈ 5.72 that corresponds to diffuse reflection at the graphite surface for both gases. Simple analysis indicates that the two gases have slightly different accommodation coefficients (about 25%) with the graphite surface. However, there could also be other reasons, such as experimental uncertainties or the need for a more detailed analysis.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Molecular dynamics study of interstitial He clusters in nickel

This study presents a molecular dynamics analysis focusing on the behavior of interstitial helium (He) clusters in nickel (Ni), examining their formation, stability, and migration energetics. Consistent with previous research, we found that the binding energies of interstitial helium within a helium cluster are positive and increase with the cluster size, indicating a preference for helium atoms to cluster together. However, our findings also reveal that while the formation energy increases monotonically with cluster size, the increase in binding energy is non-monotonic. Importantly, small He clusters were observed to be thermally unstable at reactor operational temperatures (approximately 600 K), with the He 2 cluster exhibiting instability even at room temperature. With a binding energy of 0.49 eV for a He 4 cluster, we hypothesize that for helium bubbles to form via homogeneous nucleation (i.e., through trap mutation) at reactor operating temperatures, the helium concentration must be high enough to facilitate the formation of helium clusters of at least size 4 or larger. As expected, interstitial helium and small helium clusters are highly mobile. This mobility was observed not only at room temperature but also at temperatures as low as approximately 200 K. Furthermore, the mean squared displacement method has been utilized to determine the migration barriers and the corresponding prefactors for clusters ranging from He 1 to He 6

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Results of the AGR-5/6/7 UCO TRISO fuel irradiation test in the Advanced Test Reactor

AGR-5/6/7 was the last in a series of irradiation experiments sponsored by the U.S. Department of Energy in support of the development and qualification of TRISO coated particle fuel for use in a high-temperature gas-cooled reactor. This experiment was conducted to verify the performance of the reference-design TRISO-coated low-enriched UCO fuel for modular high-temperature gas-cooled reactor normal operating conditions and to explore fuel performance at temperatures substantially beyond those typical of normal operation. A total of 194 UCO fuel compacts in five capsules were irradiated in the Advanced Test Reactor for 360.9 effective full-power days, achieving final burnup ranging from 5.66% to 15.26% fissions per initial heavy metal atom and fast neutron fluence ranging from 1.62 × 10 25 to 5.55 × 10 25 n/m 2 (E > 0.18 MeV). Calculated time-averaged fuel temperatures ranged from 467 °C to 1432 °C, with a peak fuel temperature of 1536 °C. During the first five irradiation cycles (∼180 effective full-power days), 85m Kr fission gas release-rate-to-birth-rate ratios were 10 −7 –10 −6 , indicating no particle failures. Near the end of the sixth cycle, a substantial number of in-pile particle failures occurred in Capsule 1. The fission gas release from this capsule impacted the readings from the other four capsules and led to unreliable fission gas release measurements for all capsules during the last four cycles. A preliminary post-irradiation examination of Capsule 1 fuel and internal components revealed the in-pile particle failures resulted from operational issues with the capsule, not subpar performance of the fuel particles.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Mitigating humidity interference in chemiresistive hydrogen sensors through hydrophobic surface functionalization

Chemiresistive gas sensors based on semiconductor metal oxides, such as tin dioxide (SnO₂), are indispensable for detecting and monitoring toxic gases and pollutants, making them critical components in industrial and environmental applications. To enhance their performance, the metal oxides are loaded with noble metals such as palladium (Pd). However, ambient humidity poses a significant challenge to their performance. The presence of adsorbed water molecules on the oxide surface can considerably impair sensor sensitivity and overall performance. To address this issue, in this paper, we report on the application of an ultrathin, hydrophobic layer of hexamethyldisilazane to the surface of a Pd/SnO 2 sensor. This study investigates the influence of hydrophobic surface modifications on the metal oxide interface, focusing on their impact on sensor sensitivity and selectivity. The resulting sensor exhibits superior hydrogen sensing capabilities, operating effectively at low temperatures even in high humidity environments. Furthermore, the hydrophobic modification reduces the sensor’s susceptibility to interfering gases, thus enhancing its selectivity. The combined enhancements in moisture resistance and selectivity achieved through HMDS surface modification, along with the superior sensitivity of Pd/SnO₂ sensors, facilitate the development of gas sensors with enhanced humidity tolerance and broader applications.

Chemiresistive gas sensors↗
DOE OSTI2022

Bonded Interfaces for High-Temperature Power Electronics

Wide-bandgap devices have pushed the operational limit of semiconductor devices in automotive power electronics packages to higher temperatures (>200 degrees C). While a higher efficiency can be achieved through the use of wide-bandgap devices, the entire package must be re-designed with components that can withstand the higher temperature limits. Sintered silver and transient liquid phase bonds are potential candidates as bonded materials for use in higher temperatures however, the underlying mechanics of deformation under thermal loads and the resulting failure mechanisms in these materials are not well understood. Furthermore, thermomechanical modeling plays a key role in understanding the degradation behavior of bonded interface materials and for design optimization of power electronics packages.

ADVANCED PROPULSION SYSTEMS,DIRECT ENERGY CONVERSI↗
DOE OSTI2024

Buffer-IPyC separation process in TRISO fuel particles simulated with Bison code

During High Temperature Gas-cooled Reactor (HTGR) operation, tristructural isotropic (TRISO) coated-particle fuel undergoes irradiation-induced changes in morphology and thermomechanical properties. Experimental results from the Advanced Gas Reactor (AGR) Fuel Development and Qualification Program show, among other things, the mechanism of gap formation between the buffer and inner pyrolytic carbon (IPyC) layers, which could be explored further via computational simulations using the Bison code. Two simulation models were developed, the debonding restricted model, where no gap formation between buffer and IPyC layers is permitted, and the debonding enabled model, where the gap between those layers is created. The inputs of the simulated models are based on the irradiation conditions from the AGR-1 experiment. The research included simulations on spherical and aspherical fuel types. Under the specific temperatures and fluences of the AGR-1 irradiation experiment, and the Bison simulations, it was concluded that the most common scenario is a gap formation along the buffer-IPyC interface, while the least possible scenario is the situation where there is no gap formation at the buffer-IPyC junction. The computational results confirmed that the sphericity of the fuel influences the thickness of the gap that occurs at the buffer-IPyC junction, in a way that with increasing aspect ratio the gap thickness increases. The results obtained for spherical and aspherical fuel are nearly identical. Finally, performed simulations match conclusions observed from the AGR-1 experiment, which as such shows that the Bison code is a good computational method for simulating the TRISO fuel. Future simulations will include the validation of performed research and comparison of the results between Bison and PARFUME codes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

FFTF HT9 Cladding Microstructure Characterization

The sodium-cooled fast reactor (SFR) is a promising candidate for next generation nuclear reactors, operating at extreme conditions which include high temperatures (>500?C core outlet temperature) and significant neutron damage. High-Cr martensitic HT9 steel is an excellent candidate for SFR cladding and duct material due to its compatibility with liquid sodium, good thermal conductivity, resistance to void swelling, and strong creep rupture strength [1-4].However, the harsh in-core environment of SFRs can cause complex microstructural changes and mechanical property degradation in HT-9. Ensuring the safe use of HT9 cladding for metallic fuel requires both a thorough understanding of its mechanical response to microstructure evolution as well as reliable microstructure-sensitive modeling predictions. Microstructure-sensitive modeling of high temperature creep behavior in HT9 cladding for SFR applications currently lack experimental data to model the phenomena accurately. To fill this need, methods to perform microstructural characterization have been developed and performed on HT9.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Significance and complications of drilling fluid rheology in geothermal drilling: A review

The harsh downhole conditions of high pressure and high temperature (HPHT) encountered in geothermal wells make the drilling operation challenging. Drilling in such environments requires a special drilling mud formulation with high thermal stability and good rheological properties to fulfill the drilling fluid functions. Therefore, great efforts should be put into selecting the suitable drilling fluid, optimize and monitor the drilling fluid properties throughout drilling operations, and predicting its performance under downhole conditions. Rheological properties significantly impact many drilling parameters such as hole cleaning, fluid and wellbore stability, wellbore hydraulics, torque and drag, and other drilling issues. This paper discusses water-based drilling fluids' flow behavior under HPHT conditions and highlights the significance of fluid rheology in geothermal drilling. The common challenges and complications related to fluid rheology encountered in geothermal drilling are addressed in this paper, such as hole cleaning, wellbore hydraulics, and drilling fluid stability. This article also reviews the recent advances in drilling mud systems, rheology enhancement, and rheological properties measurements at surface and subsurface conditions. Furthermore, the rheology models of drilling fluid at elevated temperatures are reviewed to fully understand their flow behavior and establish a method for drilling engineers to optimize fluid formulations for geothermal drilling.

58 GEOSCIENCES↗
DOE OSTI2022

Development of Cast Valve Bodies For High Temperature Service

Gen 3 Concentrating Solar-Thermal Power (CSP) system components are required to operate at 750°C - 800°C to achieve the Sunshot target of 6 cents/kWh. Haynes ® 282 and IN ® 740H are preferred alloys for the construction of these components due to their high tensile and creep strengths for service at temperatures greater than 750°C. There is significant motivation to lower the cost of materials and components so that the capital costs can be minimized. One approach to reduce costs is to fabricate castings at the lowest possible cost. To obtain the lowest cost in castings, there is a significant need to maximize yields in castings by decreasing rejects due to casting defects and to minimize wastage in material lost in the gating systems. However, very little work has been performed to develop cast products using Haynes ® 282. Although preliminary work has established the feasibility of casting Haynes ® 282 using investment and sand casting, there are no commercial cast components available. In particular, there is significant interest in the development of casting design and process technology for the fabrication of components such as valve bodies using Haynes ® 282.

14 SOLAR ENERGY↗
DOE OSTI2024

High-Temperature Freeze & Leak-Resistant Advanced Molten Salt Valve (Final Project Report)

The overall goal of this investigation was to develop an innovative high-temperature chloride molten salt flow control valve capable of operation up to 750 °C. The team developed an integrated active and passive thermal management system to ensure robust design for freeze-thaw cycles, with either a bellows-sealed configuration, a high-temperature stuffing box, or combination of the two. The STM system is unique in the industry.

14 SOLAR ENERGY↗