Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fatigue testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Hydrogen effects on low-cycle fatigue of the single-crystal nickel-base superalloy CMSX-2

The effects of hydrogen on the low-cycle fatigue behavior of CMSX-2 (001)-oriented single crystals were examined. Fatigue tests were conducted under constant plastic strain amplitude control. Cyclic stress-strain curves and fatigue life data at different plastic strain amplitudes were determined for hydrogen-free and hydrogen-charged specimens. Two charging procedures, leading to different hydrogen concentrations, were applied. Hydrogen was found to decrease significantly the number of cycles to failure under the various experimental conditions. The increasing hydrogen concentration and ratio of the hydrogen to nonhydrogen-containing volume were found to shorten fatigue life in hydrogen-charged specimens. Based on the analysis of cyclic stress-strain curves and optical and transmission electron microscopy, it was established that hydrogen enhanced strain localization and promoted crystallographic stage I cracking, leading to embrittlement.

Dollar, M.↗
NASA NTRS1991

Characterization of multiaxial warp knit composites

The objectives were to characterize the mechanical behavior and damage tolerance of two multiaxial warp knit fabrics to determine the acceptability of these fabrics for high performance composite applications. The tests performed included compression, tension, open hole compression, compression after impact and compression-compression fatigue. Tests were performed on as-fabricated fabrics and on multi-layer fabrics that were stitched together with either carbon or Kevlar stitching yarn. Results of processing studies for vacuum impregnation with Hercules 3501-6 epoxy resin and pressure impregnation with Dow Tactix 138/H41 epoxy resin and British Petroleum BP E905L epoxy resin are presented.

Dexter, H. Benson↗
NASA NTRS1940

Creep Strength of Stabilized Wrought-aluminum Alloys

Rohn-type equipment has been mounted on rubber blocks, for the purpose of damping the vibrations of the ground and of rendering the plastic yielding of the test bars less subject to outside interferences. New equipment also included three shockproof creep-testing machines with the Martens mirror instruments for recording the strain curve of the fatigue-tested specimens.

Muller, W↗
DOE OSTI2021

Quantitative Non-Destructive Evaluation of Fatigue Damage Based on Multi-Sensor Fusion

Based on sensor fusion and machine learning, this project developed a novel non-destructive evaluation (NDE) methodology, which consists of a remaining useful life (RUL) prediction framework and regression models for predicting residual stress and full width at half maximum (FWHM). A series of fatigue testing experiments were conducted using 5052-H32 aluminum alloy specimens. All specimens were measured using linear ultrasonic (LU) and nonlinear ultrasonic (NLU) testing methods non-destructively. Machine learning models were developed to use LU and NLU measurements to predict loading condition, fatigue level, residual stress, and FWHM. It was demonstrated that the developed methodology could distinguish new and fatigue specimens with an accuracy of 97.53%. Also, the prediction errors for residual stress and FWHM were as low as 4.73% and 1.62%, respectively. An interactive database was created to publicly share the data generated from the project. It is envisioned that the developed NDE technology will equip manufacturers with a responsive screening system for incoming used metallic components, and potentially lead to a significant increase in using used metallic components for remanufacturing.

42 ENGINEERING↗
DOE OSTI2024

Very high cycle fatigue characteristics of laser beam powder bed fused AlSi10Mg: A systematic evaluation of part geometry

This study explores the influence of geometry and part size on defect distribution, melt pool size, and mechanical characteristics in laser beam powder bed fused (LB-PBF) AlSi10Mg. Five distinct geometries—hourglass, small rod, small block, large block, and large rod—were fabricated under identical process parameters. Fully reversed ultrasonic fatigue testing, operating at a frequency of 20 kHz, was conducted to assess the very high cycle fatigue properties. The findings indicated that part geometry had a major impact on the fatigue properties of the material in the very high cycle fatigue regime. Specimens machined from large rods and large blocks had the lowest porosity and highest fatigue resistance. Microstructural analysis indicated that hourglass, small rod, and small block specimens had shallower melt pools and overlap depths compared to other geometries. This observation suggests a higher cooling rate in specimens with smaller cross-sectional areas, leading to the increased presence of entrapped gas pores and a lack of fusion defects. Understanding the relationship between part geometry and fatigue properties in LB-PBF components offers insights for optimizing design and manufacturing processes in additive manufacturing applications.

AlSi10Mg↗
NASA NTRS1973

Correlation of magnetic perturbation inspection data with rolling element bearing fatigue results

A magnetic perturbation technique was used to nondestructively detect subsurface nonmetallic inclusions in the inner races of 207-size, deep groove ball bearings. The bearings were fatigue tested at 2750 rpm under a radial load of. The inner races were subsequently sectioned at fatigue spall locations and at magnetic perturbation signal locations. Analyses of the data indicated good correlation between magnetic perturbation signals and inclusion size and location. Exclusion of those bearings that had significant magnetic perturbation signals did not alter the statistical life of the bearings.

Parker, R. J.↗
NASA NTRS1976

Fatigue-crack initiation and growth in notched 2024-T3 specimens monitored by a video tape system

Fatigue-crack initiation and early stages of growth in notched 2024-T3 aluminum alloy sheet specimens were monitored during constant-amplitude fatigue tests conducted for a range of stress ratios. A video tape system was developed to detect fatigue cracks 0.1 mm in length on the sheet surface and to monitor their growth. Fatigue cracks initiated either at the notch corner or on the notch surface. Most of the first fatigue cracks started as notch-corner cracks, and the crack-initiation period was defined as the number of cycles for which the crack was 0.1 mm in length on the sheet surface. For each of the stress ratios used, the results showed that at the low stress levels, the crack-initiation period constituted at least 90 percent of the fatigue lives. However, for the negative stress ratios at the high stress levels, cracks started as early as at about 40 percent of the fatigue lives.

Sova, J. A.↗
NASA NTRS1976

Joint aircraft loading/structure response statistics of time to service crack initiation

A reliability analysis for predicting the statistical distribution of time to fatigue crack initiation for aircraft structures in service is presented. The present analysis utilizes the statistical data of the specimen fatigue tests, the full-scale structure tests, and the statistical dispersion of aircraft service loads. The statistical distribution of the time to fatigue crack initiation of the full-scale structure under laboratory loading spectrum is assumed to be Weibull. The service loads for gust turbulences are modeled as Poisson processes for transport-type aircraft, while the maneuver loads are modeled as compound Poisson processes for fighter and training aircraft. It is found that the statistical distribution of time to fatigue crack initiation for aircraft structures in service is not Weibull and that the prediction on the basis of the Weibull distribution is unconservative, in particular in the early service time.

Yang, J.-N.↗
NASA NTRS1979

Design, durability and low cost processing technology for composite fan exit guide vanes

A lightweight composite fan exit guide vane for high bypass ratio gas turbine engine application was investigated. Eight candidate material/design combinations were evaluated by NASTRAN finite element analyses. A total of four combinations were selected for further analytical evaluation, part fabrication by two ventors, and fatigue test in dry and wet condition. A core and shell vane design was chosen in which the unidirectional graphite core fiber was the same for all candidates. The shell material, fiber orientation, and ply configuration were varied. Material tests were performed on raw material and composite specimens to establish specification requirements. Pre-test and post-test microstructural examination and nondestructive analyses were conducted to determine the effect of material variations on fatigue durability and failure mode. Relevant data were acquired with respect to design analysis, materials properties, inspection standards, improved durability, weight benefits, and part price of the composite fan exit guide vane.

Blecherman, S. S.↗
NASA NTRS1985

Flight service evaluation of composite helicopter components

An assessment of composite helicopter structures, exposed to environmental effects, after four years of commercial service is presented. This assessment is supported by test results of helicopter components and test panels which have been exposed to environmental effects since late 1979. Full scale static and fatigue tests are being conducted on composite components obtained from S-76 helicopters in commercial operations in the Gulf Coast region of Louisiana. Small scale tests are being conducted on coupons obtained from panels being exposed to outdoor conditions in Stratford, Connecticut and West Palm Beach, Florida. The panel layups represent S-76 components. Moisture evaluations and strength tests are being conducted, on the S-76 components and panels, over a period of eight years. Results are discussed for components and panels with up to four years of exposure.

Rich, M. J.↗
NASA NTRS1984

Constitutive modeling for isotropic materials

A state-of-the-art review of applicable constitutive models with selection of two for detailed comparison with a wide range of experimental tests was conducted. The experimental matrix contained uniaxial and biaxial tensile, creep, stress relaxation, and cyclic fatigue tests at temperatures to 1093 C and strain rates from .0000001 to .001/sec. Some nonisothermal cycles will also be run. The constitutive models will be incorporated into the MARC finite element structural analysis program with a demonstration computation made for advanced turbine blade configuration. In the code development work, particular emphasis is being placed on developing efficient integration algorithms for the highly nonlinear and stiff constitutive equations. Another area of emphasis is the appropriate and efficient methodology for determing constitutive constants from a minimum extent of experimental data.

Lindholm, U. S.↗
NASA NTRS1989

Test methods and design allowables for fibrous composites. Volume 2

Topics discussed include extreme/hostile environment testing, establishing design allowables, and property/behavior specific testing. Papers are presented on environmental effects on the high strain rate properties of graphite/epoxy composite, the low-temperature performance of short-fiber reinforced thermoplastics, the abrasive wear behavior of unidirectional and woven graphite fiber/PEEK, test methods for determining design allowables for fiber reinforced composites, and statistical methods for calculating material allowables for MIL-HDBK-17. Attention is also given to a test method to measure the response of composite materials under reversed cyclic loads, a through-the-thickness strength specimen for composites, the use of torsion tubes to measure in-plane shear properties of filament-wound composites, the influlence of test fixture design on the Iosipescu shear test for fiber composite materials, and a method for monitoring in-plane shear modulus in fatigue testing of composites.

Chamis, Christos C.↗
NASA NTRS1989

Two-dimensional high temperature strain measurement system

Two-dimensional optical strain measurements on high temperature test specimens are presented. This two-dimensional capability is implemented through a rotatable sensitive strain axis. Three components of surface strain can be measured automatically, from which the first and second principal strains are calculated. One- and two-dimensional strain measurements at temperatures beyond 750 C with a resolution of 15 microstrain are demonstrated. The system is based on a one-dimensional speckle shift technique. The speckle shift technique makes use of the linear relationship between surface strain and the differential shift of laser speckle patterns in the diffraction plane. Laser speckle is a phase effect that occurs when spatially coherent light interacts with an optically rough surface. Since speckle is generated by any diffusely reflecting surface, no specimen preparation is needed to obtain a good signal. Testing was done at room temperature on a flat specimen of Inconel 600 mounted in a fatigue testing machine. A load cell measured the stress on the specimen before and after acquiring the speckle data. Strain components were measured at 0 C (parallel to the load axis) and at plus or minus 45 C, and plots indicate the calculated values of the first and second principal strains. The measured values of Young's modulus and Poisson's ratio are in good agreement with handbook values. Good linearity of the principal strain moduli at high temperatures indicate precision and stability of the system. However, a systematic error in the high-temperature test setup introduced a scale factor in the slopes of the two-dimensional stress-strain curves. No high temperature effects, however, have been observed to degrade speckle correlation.

Lant, Christian T.↗
NASA NTRS1991

Structural integrity of future aging airplanes

A multitude of design considerations is involved in ensuring the structural integrity of Boeing jet transports that have common design concepts validated by extensive analyses, tests, and three decades of service. As airplanes approach their design service objectives, the incidences of fatigue and corrosion may become widespread. Continuing airworthiness of the aging jet fleet requires diligent performance from the manufacturer, the airlines, and airworthiness authorities. Aging fleet support includes timely development of supplemental structural inspection documents applicable to selected older airplanes, teardown inspections of high-time airframes retired from service, fatigue testing of older airframes, and structural surveys of more than 130 airplanes operated throughout the world. Lessons learned from these activities are incorporated in service bulletin recommendations, production line modifications, and design manual updates. An overview of traditional Boeing fleet support activities and the anticipated benefits for future generations of commercial airplanes based on the continuous design improvement process are presented.

Aging Aircraft↗
NASA NTRS2014

Data Fusion Tool for Spiral Bevel Gear Condition Indicator Data

Tests were performed on two spiral bevel gear sets in the NASA Glenn Spiral Bevel Gear Fatigue Test Rig to simulate the fielded failures of spiral bevel gears installed in a helicopter. Gear sets were tested until damage initiated and progressed on two or more gear or pinion teeth. During testing, gear health monitoring data was collected with two different health monitoring systems. Operational parameters were measured with a third data acquisition system. Tooth damage progression was documented with photographs taken at inspection intervals throughout the test. A software tool was developed for fusing the operational data and the vibration based gear condition indicator (CI) data collected from the two health monitoring systems. Results of this study illustrate the benefits of combining the data from all three systems to indicate progression of damage for spiral bevel gears. The tool also enabled evaluation of the effectiveness of each CI with respect to operational conditions and fault mode.

health monitoring↗
NASA NTRS1981

Fatigue degradation in compressively loaded composite laminates

The effect of imbedded delaminations on the compression fatigue behavior of quasi-isotropic, T300/5208, graphite/epoxy laminates was investigated. Teflon imbedments were introduced during panel layup to create delaminations. Static and constant amplitude (R=10, omega = 10 Hz) fatigue tests were conducted. S-N data and half life residual strength data were obtained. During static compression loading, the maximum deflection of the buckled delaminated region was recorded. Under compression fatigue, growth of the imbedded delamination was identified as the predominant failure mode in most of the test cases. Specimens that exhibited others failures had a single low stiffness ply above the Teflon imbedment. Delamination growth during fatigue was monitored using DIB enhanced radiography. In specimens with buried delaminations, the dye penetrant (DIB) was introduced into the delaminated region through a minute laser drilled hole, using a hypodermic needle. A low kV, microfocus, X-ray unit was mounted near the test equipment to efficiently record the cyclic growth of buried delaminations on Polaroid film.

Ramkumar, R. L.↗
NASA NTRS1998

High-Temperature Slow Crack Growth of Silicon Carbide Determined by Constant-Stress-Rate and Constant-Stress Testing

High-temperature slow-crack-growth behaviour of hot-pressed silicon carbide was determined using both constant-stress-rate ("dynamic fatigue") and constant-stress ("static fatigue") testing in flexure at 1300 C in air. Slow crack growth was found to be a governing mechanism associated with failure of the material. Four estimation methods such as the individual data, the Weibull median, the arithmetic mean and the median deviation methods were used to determine the slow crack growth parameters. The four estimation methods were in good agreement for the constant-stress-rate testing with a small variation in the slow-crack-growth parameter, n, ranging from 28 to 36. By contrast, the variation in n between the four estimation methods was significant in the constant-stress testing with a somewhat wide range of n= 16 to 32.

Choi, Sung H.↗
NASA NTRS1976

Rolling-element fatigue lives of AISI 52100 steel balls with several synthetic lubricants

Rolling-element fatigue tests were run with three synthetic lubricants with and without antiwear additives and with a paraffinic mineral oil at race temperatures of 336 to 353 K (146 146 to 175 F). The five-ball fatigue tester was used with steel balls to evaluate the relative fatigue lives with each of six lubricant-additive combinations. The tests were run at 5,520 MPa (800,000psi) maximum Hertz stress, 10,000 rpm shaft speed, and 30 deg contact angle. The lubricants tested have similar kinetic viscosities at 372 K (210 F) ranging from 0.034 to 0.089 sq cm/sec (3.4 to 8.9 cS). At these conditions, the mode of failure in the five-ball fatigue tester was classical subsurface rolling-element fatigue. The baseline for comparison of fatigue life was the paraffinic mineral oil without additives. The effects of the synthetic lubricants and their additives, which are useful for boundary lubrication, oxidation or foam inhibition, were evaluated.

Parker, R. J.↗