Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Coupled Simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Forecasting Dynamic Line Rating with Spatial Variation Considerations

Dynamic line rating (DLR) is a technology that allows the ampacity of an electrical conductor to be calculated using real-time or forecasted weather conditions. Historically, the ampacity of a conductor has been determined using a static line rating method which assumes conservative weather assumptions. Therefore, not only can DLR give a more accurate measurement of the true ampacity of a conductor, but it can also increase its ampacity during weather conditions with greater thermal mitigations. The two primary cooling factors in the ampacity calculations are wind speed and direction. In complex terrain, wind speed and direction can have large variations over short distances. Therefore, accurately identifying the limiting span of a transmission line requires high spatial resolution of the wind along its path. One solution is to install dense weather stations along their path, though this can become costly over long distances. Therefore, researchers have investigated the use of Computation Fluid Dynamic (CFD) simulations to accurately compute the wind field along the path of a transmission line and use these results to identify the limiting section of the conductor. This work presents a case study that evaluates the coupling of CFD simulations and forecasted weather simulations using the High-Resolution Rapid Refresh (HRRR) model points over a 2-year span within a region in south eastern Idaho. The primary goal of the work is the evaluation of the number of HRRR model points used, i.e., weather stations, along the path of the line and the accuracy of the resulting DLR ampacity. This was done using 4, 10, 17, 26, and 35 HRRR model points along two transmission line paths. The results indicate that as the number of model points are increased, the DLR ampacity of the lines decrease, yet converge as more points are added and demonstrate little change with additional HRRR points. It is expected that these results can help transmission line operators identify the number of weather stations that must be installed when coupled with CFD simulations and DLR ampacity to ensure accurate ratings and safe operations.

17 WIND ENERGY↗
DOE OSTI2020

Chirality transfer and chiral turbulence in gauge theories

Chirality transfer between fermions and gauge fields plays a crucial role for understanding the dynamics of anomalous transport phenomena such as the Chiral Magnetic Effect. In this proceeding we present a first principles study of these processes based on classical-statistical real-time lattice simulations of strongly coupled QED (e 2 N f = 64). Furthermore, our simulations demonstrate that a chirality imbalance in the fermion sector triggers chiral plasma instabilities in the gaugefield sector, which ultimately lead to the generation of long range helical magnetic fields via an self-similar turbulent cascade of the magnetic helicity.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2021

Spin-lattice dynamics of surface vs core magnetization in Fe nanoparticles

Magnetization of clusters is often simulated using atomistic spin dynamics for a fixed lattice. Coupled spinlattice dynamics simulations of the magnetization of nanoparticles have up to now neglected the change in the size of the atomic magnetic moments near surfaces. We show that the introduction of variable magnetic moments leads to a better description of experimental data for the magnetization of small Fe nanoparticles. To this end we divide atoms into a surface-near shell and a core with bulk properties. Here, it is demonstrated that both the magnitude of the shell magnetic moment and the exchange interactions need to be modified to obtain a fair representation of the experimental data. This allows for a reasonable description of the average magnetic moment versus cluster size, and also the cluster magnetization versus temperature.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2025

Optimization of simulated high-field side lower hybrid current drive coupling using machine learning predictions of scrape-off layer density

Lower hybrid current drive (LHCD) is a potential source of non-inductive off-axis current drive (CD) for tokamaks. Although LHCD has been successfully deployed on a number of tokamaks, it is highly sensitive to the scrape-off layer (SOL) conditions local to the LHCD launcher. Large gaps between the launcher and plasma core, SOL turbulence, or edge density perturbations due to edge-localized modes can hamper CD or cause large reflected power. These coupling issues in part motivated the installation of an LHCD launcher on the high-field side (HFS) of DIII-D. On the HFS, the SOL is less turbulent and more controllable compared to the low-field side. This quiescence may result in more predictable edge conditions and thus a more predictable CD. Here, in this work, HFS SOL reflectometry measurements are predicted from global plasma parameters using machine learning models. The SOL predictions coupled with the full-wave simulation of the LHCD launcher allow for the prediction of reflected power, directivity, and arcing risk before the discharge. Launcher performance is then optimized using multi-objective Bayesian optimization, finding the shot parameters that result in an optimal SOL density that maximizes CD while minimizing the risk of arcing. The predictions and optimizations of LHCD performance are then accelerated using a surrogate model of the full-wave LHCD simulation.

Bayesian optimization↗
DOE OSTI2025

Simulations of Radiation Hydrodynamics in Strongly Coupled Plasmas (Final Report)

Radiation propagates throughout the Universe and is often the only information we have from distant astronomical objects. Additionally, radiation plays a key role in systems ranging from the interior of stars to the establishment of shocks at the edges of forming galaxies to neutron star mergers. Here radiative processes, absorption, emission, and scattering, are fundamental to transport of momentum and energy, as well as, the overall evolution of these and other astrophysical systems. In some cases, radiation-dominant systems are also sufficiently dense and ionized, such that, the ions are strongly coupled (ie electrostatic energy >> thermal energy or Γ >> 1), which will affect radiative processes and the transport of radiation. During this project, we developed a computational ray-tracing algorithm to study radiation transport through a simulated neutron star capsule implosion under conditions relevant to Omega-60 laser experiments.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2022

Simulation of runaway electron production with CQL3D coupled to NIMROD

Abstract A coupling between two distinctly different codes—one magnetohydrodynamic (MHD) and another kinetic—is achieved and applied for simulation of runaway electron (RE) production. The 3D initial value MHD code NIMROD simulates a DIII-D pure neon shattered pellet injection plasma quench including the propagation and ablation of the fragments, ionization and recombination of the impurities, and the radiated and transported energies. The field data from NIMROD is then used by the bounce-averaged Fokker–Planck Collisional QuasiLinear 3D (CQL3D) kinetic code to simulate the production of REs and their radial transport. The coupling procedure involves mapping of data between different grids and adjustment of the NIMROD toroidal electric field when REs appear. It is shown that without the radial transport, a large RE current is generated, up to 30% of the pre-pellet ohmic current. However, when the radial transport is included in CQL3D, the RE current is reduced to undetectable level, consistent with experiment. Various forms of the radial diffusion are surveyed to determine conditions when the fast electrons would not have time to be accelerated to relativistic energies before they are lost to chamber wall.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Coupled radiation transport and plasma physics for ICF simulations [Slides]

Describing high-temperature plasmas requires inclusion of several nonlinear coupled physics, including ion kinetics - for each isotope species present in the plasma, electron kinetics, thermal radiative transfer (TRT), electromagnetic description, and nuclear reactions (fusion burn). Simulating plasmas in ICF hohlraums aims to solve kinetic ions (particles), fluid electrons, energetic electrons, electromagnetics, kinetic radiation (MG DP solver), and laser-plasma interactions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

A coupled fluid-mechanical workflow to simulate the directed energy deposition additive manufacturing process

Simulation of additive manufacturing processes can provide essential insight into material behavior, residual stress, and ultimately, the performance of additively manufactured parts. In this work, we describe a new simulation based workflow utilizing both solid mechanics and fluid mechanics based formulations within the finite element software package SIERRA (Sierra Solid Mechanics Team in Sierra/Solid Mechanics 4.52 User’s Guide SAND2019-2715. Technical report, Sandia National Laboratories, 2011) to enable integrated simulations of directed energy deposition (DED) additive manufacturing processes. In this methodology, a high-fidelity fluid mechanics based model of additive manufacturing is employed as the first step in a simulation workflow. This fluid model uses a level set field to track the location of the boundary between the solid material and background gas and precisely predicts temperatures and material deposition shapes from additive manufacturing process parameters. Next, the resulting deposition shape and temperature field from the fluid model are then mapped into a solid mechanics formulation to provide a more accurate surface topology for radiation and convection boundary conditions and a prescribed temperature field. Solid mechanics simulations are then conducted to predict the evolution of material stresses and microstructure within a part. By combining thermal history and deposition shape from fluid mechanics with residual stress and material property evolutions from solid mechanics, additional fidelity and precision are incorporated into additive manufacturing process simulations providing new insight into complex DED builds.

36 MATERIALS SCIENCE↗
DOE OSTI2023

kynema-driver [SWR-23-10]

Kynema-driver (FKA: exawind-driver) is a C++ code that is part of the kynema software stack. It is a driver for coupled Kynema-SGF/UGF simulations. It was designed to couple and drive hybrid-solver computational fluid dynamics (CFD) simulations where NLR'S kynema-sgf (SWR-20-85) software and NLR'S kynema-ugf (SWR-20-27) CFD codes are run simultaneously and are two-way coupled via overset meshes and the TIOGA overset-mesh library.

Rood, Jonathan↗
DOE OSTI2022

Simulations for HEP with SQMS Quantum Hardware (Snowmass2021 - Letter of Interest)

The Superconducting Quantum Materials and Systems (SQMS) Center, a Fermilab lead NQI center, will develop and deploy a beyond state of the art quantum computers. These systems will exhibit long coherent times, and a high degree of connectivity. We are interested in exploring the utility of these devices to address computational challenges in HEP, such as the simulation of strongly coupled quantum field theories. A progression of toy models and simulations can begin to chart a course towards simulating QCD-like systems.

42 ENGINEERING↗
DOE OSTI2021

Non-degenerate parametric mixing and Q-enhancement in ALN Lamb wave resonator

In this Letter, we explore a non-degenerate phase independent parametric quality factor (Q)-enhancement technique for aluminum nitride (AlN) Lamb wave resonators. Unlike other active Q-enhancement techniques which require precise phase control of the electronic feedback loop, this technique is implemented by parametrically pumping AlN material stiffness to realize a negative resistance seen at the signal path. The negative resistance is dependent on the nonlinear material modulation and multi-resonance coupling in the device. A nonlinear circuit model is developed to simulate the parametric coupling of each resonance and extract the nonlinearity of AlN from experimental data. With proper pump frequency and pump power, the device quality factor is boosted in both simulation and experiment. The demonstrated Q-enhancement method is simple to implement and can be applied to other types of resonators that have nonlinear behavior and support multi-resonance operation.

42 ENGINEERING↗
DOE OSTI2025

Selective Recovery of Critical Minerals from Simulated Electronic Wastes Via Reaction‐Diffusion Coupling

Abstract Atom‐ and energy‐efficient chemical separations are urgently needed to meet the surging demand for critical materials that has strained supply chains and threatened environmental damage. In this study, we used reaction‐diffusion coupling to separate iron, neodymium, and dysprosium ions from model feedstocks of permanent magnets, which are typically found in electronic wastes. Feedstock solutions were placed in contact with a hydrogel loaded with potassium hydroxide and/or dibutyl phosphate, resulting in complex precipitation patterns as the various metal ions diffused into the reaction medium. Specifically, we observed the precipitation of up to 40 mM of iron from the feedstock, followed by the enrichment of 73 % dysprosium, and the extraction of >95 % neodymium product at a further distance from the solution‐gel interface. We designed a series of experiments and simulations to determine the relevant ion diffusivities, D Nd =5.4×10 −10 and D Dy =5.1×10 −10 m 2 /s, and precipitation rates, k Nd =1.0×10 −5 and k Dy =5.0×10 −3 m 9 mol −3 s −1 , which enabled a numerical model to be established for predicting the distribution of products in the reaction medium. Our proof‐of‐concept study validates reaction‐diffusion coupling as an effective and versatile approach for critical materials separations, without relying on ligands, membranes, resins, or other specialty chemicals.

Wang, Qingpu [Physical and Computational Sciences ↗
DOE OSTI2022

A Simulation-based Method for Correcting Mode Coupling in CMB Angular Power Spectra

Modern cosmic microwave background (CMB) analysis pipelines regularly employ complex time-domain filters, beam models, masking, and other techniques during the production of sky maps and their corresponding angular power spectra. However, these processes can generate couplings between multipoles from the same spectrum and from different spectra, in addition to the typical power attenuation. Within the context of pseudo-C ℓ based, MASTER-style analyses, the net effect of the time-domain filtering is commonly approximated by a multiplicative transfer function, F ℓ , that can fail to capture mode mixing and is dependent on the spectrum of the signal. To address these shortcomings, we have developed a simulation-based spectral correction approach that constructs a two-dimensional transfer matrix, ${J}_{{\ell }{\ell }^{\prime} }$, which contains information about mode mixing in addition to mode attenuation. We demonstrate the application of this approach on data from the first flight of the Spider balloon-borne CMB experiment.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2022

Reliability estimation of an advanced nuclear fuel using coupled active learning, multifidelity modeling, and subset simulation

Tristructural isotropic (TRISO)-coated particle fuel is a robust nuclear fuel and determining its reliability is critical for the success of advanced nuclear technologies. However, TRISO failure probabilities are small and the associated computational models are expensive. Here we used coupled active learning, multifidelity modeling, and subset simulation to estimate the failure probabilities of TRISO fuels using several 1D and 2D models. With multifidelity modeling, we replaced expensive high-fidelity (HF) model evaluations with information fusion from two low-fidelity (LF) models. For the 1D TRISO models, we considered three multifidelity modeling strategies: only Kriging, Kriging LF prediction plus Kriging correction, and deep neural network (DNN) LF prediction plus Kriging correction. While the results across these multifidelity modeling strategies compared satisfactorily, strategies employing information fusion from two LF models called the HF model least often. Next, for the 2D TRISO model, we considered two multifidelity modeling strategies: DNN LF prediction plus Kriging correction (data-driven) and 1D TRISO LF prediction plus Kriging correction (physics-based). The physics-based strategy, as expected, consistently required the fewest calls to the HF model. However, the data-driven strategy had a lower overall simulation time since the DNN predictions are instantaneous, and the 1D TRISO model requires a non-negligible simulation time.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Simulations of the Large Surface Explosion Coupling Experiment (LSECE)

The Large Surface Explosion Coupling Experiment (LSECE) project will include two surface energetic events (chemical explosions) conducted as close as possible to ground zero (GZ) of the Source Physics Experiment (SPE) Phase II Dry Alluvium (DAG) site in Yucca Flat at the Nevada National Security Site (NNSS). Seismic and acoustic data from these events will complement DAG buried source data and improve interpretation of speed-of-sound signals from explosions for national security programs. A satellite image of the region near GZ along with some of the recording stations that we will use for the far- eld simulation is shown in Figure 1. The working design of the HE package is shown in the Figure 2 and is roughly a cube of C-4 bricks.

58 GEOSCIENCES↗
DOE OSTI2022

Cryogenic energy storage: Standalone design, rigorous optimization and techno-economic analysis

Energy storage allows flexible use and management of excess electricity and intermittently available renewable energy. Cryogenic energy storage (CES) is a promising storage alternative with a high technology readiness level and maturity, but the round-trip efficiency is often moderate and the Levelized Cost of Storage (LCOS) remains high. The complex flowsheets with intricate thermodynamics at cryogenic temperatures as well as the presence of multiple loops and refrigeration cycles pose considerable challenges for rigorous model-based design and optimization of CES systems. We present an optimization strategy that couples rigorous process simulation and Bayesian optimization with flowsheet decomposition and identification of hidden coupling constraints to optimally design standalone CES systems. Further refinement is done via a local search using the limited-memory Broyden–Fletcher–Goldfarb–Shanno algorithm. Here our results indicate that it is possible to achieve more than 52% round-trip efficiency and an LCOS of $153/MWh for a standalone 100 MW/400 MWh CES system limited to short-term storage with daily charging–discharging. However, a detailed techno-economic assessment reveals that the LCOS considering total capital investment may exceed $267/MWh when all direct and indirect costs of installation and operation are considered.

25 ENERGY STORAGE↗
DOE OSTI2021

Development and Demonstration of a Reduced-Order PWR Power Dispatch Simulator

This report describes the development, modeling, and results of a reduced-order thermal power dispatch pressurized water reactor (RO-TPD-PWR) power plant simulator that incorporates coupled electrical and thermal power dispatch to an industrial process. The simulator is built on models that have been developed in previous work, including a Rancor Microworld model previously developed by INL and the University of Idaho [Ref] and reactor core and secondary system models that have been published previously [Ref]. The simulator also includes a scalable model of a high temperature electrolysis (HTE) system that has been developed at INL. A particular benefit of the Rancor Microworld model is that it is compatible with a human-system interface (HMI) that has already been developed by the Human System Simulation Laboratory (HSSL) at INL that can emulate the control room of a PWR for realistic human-in-the-loop studies with mock nuclear power plant operating procedures. The results of these human-in-the-loop tests will be compared with similar tests using a commercial full-scope generic PWR (GPWR) simulator that has been modified to include thermal power dispatch, referred to as the TPD-GPWR [ , ]. The simplicity of the RO-TPD-PWR helps to better understand and verify the results of the TPD-GPWR, which employs >1,000 variables and has much greater complexity. A second key purpose of the RO-TPD-PWR simulator is that its relative simplicity allows it scale between lab-size equipment (~100 kW) and full-scale nuclear power plants (~1 GW) by adjusting only a few parameters in the models, such as fluid masses and heat exchanger areas. The RO-TPD-PWR simulator will be used to guide the controls of lab tests, so that equipment in those tests, such as the Thermal Energy Distribution System (TEDS) and pilot-scale high temperature electrolysis (HTE) units at scales of 50-250 kW, may operate in a manner that is relevant to full-scale PWR operations.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2024

Simulation of Microcapsule Transport in Fractured Media Using Coupled CFD‐DEM

Geothermal energy is sustainable and gaining momentum as a solution to energy crises and environmental issues. However, challenges like production temperature and thermal breakthrough can impact geothermal project efficiency. One innovative solution to alleviate the thermal breakthrough is to inject polymer-based materials that are encapsulated in microcapsules into fractures to modify fracture permeability and prevent preferential flow. In our study, we utilized a coupled computational fluid dynamics and discrete element method to simulate the transport of microcapsules under various scenarios controlled by microcapsule size, microcapsule concentration, and fracture roughness. For a smooth fracture, the results indicate that small microcapsules can travel through a smooth fracture regardless of their concentrations. Large microcapsules can transport through a smooth fracture when present in lower concentrations. However, medium and mixed-size microcapsules tend to cause the sealing of a smooth fracture, irrespective of their concentrations. For a rough fracture, the transport of microcapsules is complicated by their interactions with the rough fracture walls. The presence of two sealing positions in a rough fracture adds further complexity to this transport phenomenon. The size and concentration of microcapsules control one sealing location, while the rough fracture walls determine the other sealing location. The rough walls substantially affect microcapsule transport, rendering the role of microcapsule size and concentration less significant. The simulation results suggest that complex fracture surfaces significantly elevate the occurrence of sealing behavior. To mitigate sealing behavior within more complex fractures, it would be beneficial to use smaller and lower concentrations of microcapsules.

15 GEOTHERMAL ENERGY↗