Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “packaging materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25

Instrumentation for Measurement of Gas Permeability of Polymeric Membranes

A mass spectrometric 'Dynamic Delta' method for the measurement of gas permeability of polymeric membranes has been developed. The method is universally applicable for measurement of the permeability of any gas through polymeric membrane materials. The usual large sample size of more than 100 square centimeters required for other methods is not necessary for this new method which requires a size less than one square centimeter. The new method should fulfill requirements and find applicability for industrial materials such as food packaging, contact lenses and other commercial materials where gas permeability or permselectivity properties are important.

Upchurch, Billy T.↗

Dielectrics for Power Electronics Applications

This presentation discusses the role of dielectric materials in power electronic packages. Two dielectric technologies - a dielectric material film-based substrate for insulation and a dielectric coolant - are discussed. The thermal performance benefits of dielectric film-based substrate in comparison with traditional direct-bond-copper substrates are studied through finite element analysis. Also, a novel cooling concept based on dielectric liquids that can contact electrically active surfaces are presented.

30 DIRECT ENERGY CONVERSION↗

Synthesizing, Compounding, and Characterizing a Heat Labile Foam (SRNL-STI-2025-00653)

Degradable polyurethane foams can be an attractive material to use for packaging, transporting, and dispositioning of nuclear materials. This LDRD project explored the possibility of finding a suitable polyol component that would achieve the intended results. Significant improvements were made on the initial findings of a three month Visiting Faculty Program.

Kranjc, Mark D. [Savannah River National Laborator↗

Fuel Matrix Degradation Model Development Update: Alloy Corrosion Rates and Hydrogen Generation

This work is being performed as part of the DOE NE Spent Fuel and Waste Science and Technology Campaign, Argillite and Crystalline Rock R&D work packages: SF-19AN01030101 and SF-19AN01030201. This document meets the milestone M4SF-19AN010301013 for Argillite R&D and the milestone M4SF-19AN010302013 for Crystalline R&D. The fuel matrix degradation (FMD) model calculates the degradation rate of spent UO2 fuel based on fundamental electrochemical theory and thermodynamics. The model provides the quantitative basis for radionuclide source term predictions in the generic disposal system analysis (GDSA) performance assessment (PA) model. The FMD model has been implemented in a manner that facilitates its integration with the GDSA-PA code and a preliminary, integrated FMD-GDSA model has been successfully tested (Jerden et al., 2017). The specific focus of on-going work is to accurately and quantitatively represent the generation of H2 in a breached waste package and its effect on the spent fuel degradation rate so that this key process can be accurately represented in PA models. It has been shown experimentally that millimolar concentrations of dissolved H2 in contact with spent fuel will inhibit oxidative dissolution and decrease the fuel degradation rates by as much as three orders of magnitude (e.g., Röllin et al., 2001, Ollila, 2008). This will lead to a significant decrease in the radionuclide source term values used in repository PA models. Sensitivity studies using the FMD model have shown that the dissolved H2 concentration is the dominant environmental variable affecting the UO2 spent fuel dissolution rate as long as a source of H2 persists in the breached waste package (Jerden et al., 2015). Therefore, on-going experimental and modeling efforts focus on H2 production, accumulation and interfacial reactions within a breached waste package. The anoxic corrosion of metallic engineering materials within a breached waste package will be the main source of H2 in crystalline and argillite rock repository systems. The most important H2-producing alloys present within a waste package include stainless steel, carbon steel, and aluminum alloys and the Zircaloy fuel cladding. A steel corrosion module was added to the FMD model to account for these H2 sources and couple the H2 generation rate with fuel degradation processes (Jerden et al., 2017). As discussed below, there is a need for experimental data from electrochemical corrosion tests to quantify the H2 generation rates due to the corrosion of these waste package alloys as a function of key environmental variables (Eh, pH, groundwater chemistry). This report presents results from series of electrochemical corrosion tests with materials present in waste packages that provide information needed to parameterize and validate the FMD model. The alloys tested include 316L stainless steel (316SS), AISI 4320 carbon steel (C-steel) and Zircaloy-4 fuel cladding (unirradiated). Potentiodynamic polarization and potentiostatic polarization tests were performed in buffer solutions at pH 4, 7 and 10 with NaCl concentrations of 0, 4 and 100 millimolar (mM). The potentiostatic tests were performed at voltages varying from 0.5 volts down to -0.66 volts, vs the standard hydrogen electrode (SHE), and all tests were performed at laboratory ambient temperatures (~22 °C). The corrosion rates measured during the electrochemical tests were used as direct input to a new FMD/in-package chemistry model that is being developed to provide accurate long-term spent fuel degradation rates as chemical conditions (Eh, pH, speciation) evolve within a breached waste package. This new model was developed by coupling the FMD model with the reactive transport code X1t, which is a module within the Geochemist’s Workbench (GWB) reaction path modeling code (Jerden et al., 2019). The reactive transport model consists of a 1D domain discretized with 21 reaction diffusion cells and includes a single waste packag

Jerden, James↗

Reliability of emerging bonded interface materials for large-area attachments

In this study, conventional thermal interface materials (TIMs), such as greases, gels, and phase change materials, pose bottlenecks to heat removal and have long caused reliability issues in automotive power electronics packages. Bonded interface materials (BIMs) with superior thermal performance have the potential to be a replacement to the conventional TIMs. However, due to coefficient of thermal expansion mismatches between different components in a package and resultant thermomechanical stresses, fractures or delamination could occur, causing serious reliability concerns. These defects manifest themselves in increased thermal resistance in the package. In this paper, the results of reliability evaluation of emerging BIMs for large-area attachments in power electronics packaging are reported. Thermoplastic (polyamide) adhesive with embedded near-vertical-aligned carbon fibers, sintered silver, and conventional lead solder (Sn 63 Pb 37 ) materials were bonded between 50.8 mm x 50.8 mm cross-sectional footprint silicon nitride substrates and copper base plate samples, and were subjected to accelerated thermal cycling until failure or 2500 cycles. Damage in the BIMs was monitored every 100 cycles by scanning acoustic microscopy. Thermoplastic with embedded carbon fibers performed the best with no defects, whereas sintered silver and lead solder failed at 2300 and 1400 thermal cycles, respectively. Besides thermal cycling, additional lead solder samples were subjected to thermal shock and thermal cycling with extended dwell periods. A finite element method (FEM)-based model was developed to simulate the behavior of lead solder under thermomechanical loading. Strain energy density per cycle results were calculated from the FEM simulations. A predictive lifetime model was formulated for lead solder by correlating strain energy density results extracted from modeling with cycles-to-failure obtained from experimental accelerated tests. A power-law-based approach was used to formulate the - redictive lifetime model.

30 DIRECT ENERGY CONVERSION↗

Fiberboard Properties and Degradation Rates for Storage of 9975 Shipping Package in KAC (2020 Status Report)

Savannah River Site (SRS) stores plutonium materials within model 9975 shipping packages in the K-Area Complex (KAC). The 9975 shipping package consists of a 35 gallon stainless steel drum, Celotex fiberboard insulation, lead shield, and primary and secondary containment vessels. The 9975 shipping package design, performance, and analysis for safe transport of radioactive material are described in the Safety Analysis Report for Packaging (SARP). Celotex fiberboard provides three safety functions: thermal insulation to limit internal temperature during a fire, criticality control, and resistance to package crushing. The fiberboard material must retain its dimensions and density within certain ranges to provide the required impact resistance, criticality control, and fire resistance. The SRS Surveillance Program monitors material performance to establish a basis for service life and ensures the continued integrity of 9975 packages. Fiberboard samples, taken from multiple fiberboard assemblies fabricated from cane and softwood fiberboard, have been conditioning in elevated temperature environments since 2005. The samples are periodically examined to monitor thermal, mechanical, and physical properties, and assess degradation trends. Fiberboard properties of interest that are evaluated to demonstrate acceptable long-term performance include dimensional stability, density, compressive strength, thermal conductivity, and specific heat capacity. Duplicate samples from multiple package sources have been tested to identify the range of variability in fiberboard properties and degradation rates. Baseline and long-term testing of fiberboard material properties have been reported previously; reference 6 summarized experimental results of cane and softwood fiberboard through May 2019 and presented degradation models for the measured properties. This report presents the cumulative data collected through June 2020 and the corresponding updated aging models.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Simulated Gamma Doses to Coating Materials for Use in High Level Waste Packages

An outer shield barrier for spent nuclear fuel is being developed in order to improve dry cask performance under mechanical, chemical, and radiological degradation and stresses. The materials proposed for the outer shield barrier are titanium nitride (TiN), a composite oxide layer consisting of ZrO{sub 2}, TiO{sub 2}, and Al{sub 2}O{sub 3}, and a final layer of molybdenum disulfide (MoS{sub 2}). The ultimate aim of this research is to develop a multi component shield material either as multiple layers or a multi material composite that will improve the performance of steel used in long-term storage casks. Two approaches are being examined through this research effort: multilayer and composite. The composition of the oxide layer is crucial to optimizing the shield's properties and performance. At equal oxide compositions the mixture of these specific oxides is commonly known as zirconolite. This material has been shown to provide a water barrier and to provide substantial corrosion resistance to the dry cask. In order to optimize the radiological performance of this layer the compositions of each oxide have been varied and analyzed for chemical, mechanical, and radiological effects on performance. Through the course of this research effort materials performance changes after gamma and neutron exposure as well as gamma and neutron attenuation of the potential shield materials have been measured and correlated to coating composition. As it is particularly difficult to design a novel, five component material with the goal of improving corrosion, wear behavior, heat tolerance, radiation tolerance, and general survivability, it is necessary to understand which coating components contribute to each property enhancement, and which are critical to design and eventual coating survivability. To compliment the experimental research effort, a study of gamma radiation doses using the relevant zirconolite constituent oxides and assorted combinations off all three, ZrO{sub 2}-TiO{sub 2}-Al{sub 2}O{sub 3}, has been conducted in order to gain insight into which, if any, ratios of the three constituent oxides may provide optimal gamma radiation shielding. Analyzing and comparing the oxides to each other it is apparent that the outer shield barrier with no zirconia has the highest absorbed dose rate at 4.88 E6 mrad/hr. The simulations run with no alumina and no titania are remarkably similar in absorbed dose rates. Alumina and titania compositions increase the absorbed dose rate increase. This is to be expected as during these simulations the zirconia composition is decreasing.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

BNFL 3013 Containers for Radioactive material Transportation

The DOE Standard, Stabilization, Packaging, and Storage of Plutonium-Bearing Materials, DOE-STD-3013-1994 — i.e., the 3013 Standard — was issued in December 1994, by the DOE weapons complex for the stabilization, packaging and safe storage of excess plutonium-bearing metal and oxides. Based on the 3013 Standard, the BNFL container was designed and developed to remove excess plutonium material from the Hanford and Rocky Flats Sites. The BNFL 3013 containers were put into certified transportation packages and sent to the Savannah River Site for storage and later disposition.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Survey Report on Commercial Off-The-Shelf (COTS) Tracking Tools

Radioactive/nuclear (R/N) materials are integral parts of many business sectors such as medicine, industry, and research. In the United States alone, approximately 3 million packages containing R/N materials are shipped annually via highways, rail, air, and water. These materials are utilized in medical diagnostics and treatments, industrial radiography, and scientific research. The secure and efficient transportation of R/N materials is paramount to public safety and national security. Recent incidents involving the loss of R/N materials during transportation highlight significant security and safety concerns. For instance, in December 2024, a package containing four encapsulated Selenium-75 sources was reported lost in transit from the Czech Republic to Madrid, raising alarms about the security of such shipments. Similarly, a Germanium-68 pin source was reported lost in transit in New Jersey in December 2024, underscoring the risks associated with transporting radioactive materials.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗

Fast and bright scintillators for ultrafast materials dynamics using 4th generation synchrotron

We present recent advances in fast and bright scintillators for ultrafast X-ray phase contrast imaging of dynamic materials experiments at the upgraded Advanced Photon Source (APS-U), a fourth generation synchrotron. APS-U enables hard X-ray imaging at frame rates of at least 13 MHz (corresponding to 77 ns or shorter interframe intervals), creating a new need for scintillators with faster response and higher light output than lutetium yttrium oxyorthosilicate (LYSO). For indirect imaging and diffraction with ultrafast cameras, commercial lanthanum bromide (LaBr3) and cerium bromide (CeBr3) are promising candidates. These materials exhibit decay times approximately a factor of two shorter than LYSO (around 40 ns) and lutetium oxyorthosilicate (LSO), while maintaining comparable light yield per incident X-ray photon. However, their implementation at APS-U requires addressing several challenges, including material limitations due to hygroscopicity, efficient optical coupling to imaging systems, and high quantum efficiency for conversion of scintillation light, predominantly at wavelengths below 400 nm, into detectable electronic signals. We report results from material characterization, detector integration and packaging, and beamline experiments of materials with impact. In addition, emerging scintillator classes, including perovskites and high-entropy materials, are discussed as potential alternatives for next-generation ultrafast X-ray diagnostics.

Wang, Zhehui [Los Alamos] (ORCID:0000000178264063)↗

Thermo-Mechanical Properties of Injection Molded Components Manufactured by Engineered Biodegradable Blends

Engineering of ductile, tough and thermal resistant PLA-based materials requires blending of PLA with other constituents by reactive twin-screw co-rotating extrusion to achieve compounds with adequate thermo-mechanical properties. Then, the compound of the polymeric blends must be melt processed to the final shape with an additional technology, namely the injection molding. The two-stage process the polymeric blends must undergo and the different rheological properties the blends must feature to be suitable to the different processing steps make extremely difficult to engineer the material. Extrusion compounding requires high viscous materials low melt flow index (MFI), while injection molding requires materials with low viscosity (high MFI). To overcome these shortcomings, this manuscript deals with the design of novel biodegradable PLA-based blends that rely on mixing PLA grades with different MFI (i.e. very low for extrusion and high for injection molding), each chosen to feature the rheological characteristics needed for each step of the two-stage transformation process. The ratio of the two PLA-grades inside the blends was the matter of the present investigation. The blends were subsequently tested for the manufacturing of single-use biodegradable and thermal resistant injection molded small cups, specifically designed for brewing of hot beverages. Lastly, the thermo-mechanical performance of the as-is and annealed cups were studied. Experimental evidences show blending of two-different grades of PLA is a promising route to formulate low impact polymeric materials suitable for demanding packaging solutions.

36 MATERIALS SCIENCE↗

Terrestrial Planet Evolution

The goals of this proposal involved constructing 1:5M scale geologic maps of V-23 (Niobe Planitia) and V-24 (Greenaway) quadrangles, and ancillary materials to be submitted to USGS as part of the VMAP project. Complete geologic maps and packages of ancillary materials for V-23 and V-24 have been submitted to USGS and are currently under review. In addition to these products, we have published or submitted various manuscript and/abstracts detailing the results of our research that has grown out of the proposed work. We presented our maps in various stages of construction at NASA Planetary Geology and Geophysics Mappers' meeting each year. We have also presented talks or posters summarizing our work at various conferences including: he Lunar and Planetary Science Conference, and the National Geological Society of America meeting. The work resulted in exciting developments of Venus lowland resurfacing. The products and publications resulting from this work are listed below.

Hansen, Vicki L.↗

The future of RADCALC- the radioactive material and waste transportation software program - 15154

This paper provides a thorough review of RADCALC, the U.S. Department of Energy (DOE)-developed software tool to assist DOE sites in making radioactive material and waste packaging and transportation determinations in compliance with applicable Federal regulations and DOE Orders and Standards. There are more than 400 registered users of the RADCALC tool across the DOE complex. DOE has also authorized a limited number of users from certain universities and foreign countries. DOE periodically upgrades the software consistent with changing domestic and international requirements, as well as needs unique to DOE. Due to recent changes in regulatory requirements by the Department of Transportation (DOT), it is necessary that the current version of RADCALC should be updated in a timely manner. Prior to investing funds in software upgrades, DOE decided to evaluate the nature of changes required and level of operational support and looked for alternatives for meeting sites' operational needs. DOE formed a joint review team consisting of experts from Energy Facility Contractors Group (EFCOG) sites, commercial waste treatment facilities and the National Laboratories. This team evaluated the RADCALC software, commercially available software packages, and internal DOE site-developed programs against an established set of criteria. The team also reviewed and prioritized regulatory changes and user-recommended enhancements. Based on extensive review, the team recommended that DOE continue to support RADCALC noting that RADCALC is a cost-effective, technically robust tool that can perform complicated radioactive material shipping determinations. The tool promotes accuracy, consistency, and completeness between shipments by a single shipper, between shippers at a given site, and between sites. The isotopic coverage, decay algorithm and the range of calculations are without compare either within DOE or in industry in a tool of this kind. The team also recommended that DOE should actively promote RADCALC use throughout the DOE complex and consider cooperative arrangements with the Department of Defense or other government entities that may have similar needs. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

MO-H-19A-03: Patient Specific Bolus with 3D Printing Technology for Electron Radiotherapy

Purpose: Bolus is widely used in electron radiotherapy to achieve desired dose distribution. 3D printing technologies provide clinicians with easy access to fabricate patient specific bolus accommodating patient body surface irregularities and tissue inhomogeneity. This study presents the design and the clinical workflow of 3D printed bolus for patient electron therapy in our clinic. Methods: Patient simulation CT images free of bolus were exported from treatment planning system (TPS) to an in-house developed software package. Bolus with known material properties was designed in the software package and then exported back to the TPS as a structure. Dose calculation was carried out to examine the coverage of the target. After satisfying dose distribution was achieved, the bolus structure was transferred in Standard Tessellation Language (STL) file format for the 3D printer to generate the machine codes for printing. Upon receiving printed bolus, a quick quality assurance was performed with patient resimulated with bolus in place to verify the bolus dosimetric property before treatment started. Results: A patient specific bolus for electron radiotherapy was designed and fabricated in Form 1 3D printer with methacrylate photopolymer resin. Satisfying dose distribution was achieved in patient with bolus setup. Treatment was successfully finished for one patient with the 3D printed bolus. Conclusion: The electron bolus fabrication with 3D printing technology was successfully implemented in clinic practice.

60 APPLIED LIFE SCIENCES↗