Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “laser manufacturing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 451 records · Page 25
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Comparison of powder bed fusion and directed energy deposition for tailoring mechanical properties of traditionally brittle alloys

The mechanical performance of an Fe-Co intermetallic alloy processed by laser powder bed fusion (L-PBF) and laser directed energy deposition (L-DED) additive manufacturing is compared. L-PBF material was characterized by high strength (500–550 MPa) and high ductility (35%) in tension, corresponding to a ~250% increase in strength and an order-of-magnitude improvement in ductility relative to conventional material. Conversely, L-DED material exhibited similarly poor tensile properties to the conventional wrought alloy, with low strength (200–300 MPa) and low ductility (0–2.7%). Finally, the disparity in properties between L-PBF and L-DED material is discussed in the context of the fundamental differences between manufacturing methods.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Precipitation hardening of laser powder bed fusion Ti-6Al-4V

Here, the laser powder bed fusion (PBF-L) additive manufacturing (AM) community has dedicated significant efforts into process optimization and control for defect-free Ti-6Al-4V. As defects become less of an issue for PBF-L Ti-6Al-4V, the processing-structure-properties (PSP) relationships between AM microstructures can now be explored to optimize mechanical properties. Lower temperature aging treatments around 550 °C in wrought Ti-6A-4V have been historically understood to precipitation harden the α phase with an ordered, hexagonal close packed (HCP) α 2 phase. The α 2 phase existed as nanoscale Ti 3 Al precipitates coherent with the parent α phase. The goal of the present investigation was to implement a vacuum heat treatment of 545 °C for 100 hours on PBF-L Ti-6Al-4V. This vacuum heat treatment took place after an initial hot isostatic pressure (HIP) treatment that decomposed the as-built, martensitic microstructure. The vacuum aging successfully produced nanoscale precipitates of α 2 phase within α-laths, confirmed via atom probe tomography (APT). Microstructural-length scale and quasi-static mechanical properties were investigated by nanoindentation and uniaxial tensile tests of miniaturized test specimens. Given the sensitivity of Ti-6Al-4V mechanical properties to small changes in chemistry, all test specimens originated from the same build. The α 2 precipitation resulted in significantly harder α-laths (≈ 2 GPa) as measured via nanoindentation, as well as a relative yield and ultimate tensile strength increase of 60 MPa and 38 MPa, respectively. Analysis of Variance (ANOVA) of the datasets revealed no statistical differences in total elongation between the HIPed and HIPed + aged specimens, indicative of the aging treatment producing a net benefit of strength with no loss in ductility.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Laser Welded Burst Disk Weld Tooling

A production run of 5550 hermetically sealed cylinder assemblies with precision pressure relief burst discs will be assembled and laser welded at a manufacturing lab at Sandia National Labs. Production of these cylinder assemblies requires many steps, including piece part machining, geometric inspection, cleaning, subassembly, complete assembly via laser welding, and finally leak checking. While this production run is large enough to invest in process optimization and specialized tooling, it is not quite large enough to dedicate new lab space and specify equipment specifically for this job. This study will investigate process parameters and their effects on quality and process flow time, as well as a fixturing design study with the goal of reducing process time while maintaining quality requirements.

42 ENGINEERING↗
DOE OSTI2020

Grain boundary engineering for additive manufacturing

In one embodiment, a method of manufacturing a metal part using a laser or electron beam during a powder bed additive manufacturing process includes melting each of a number of layers of metal powder of the metal part with an effective amount of energy using the laser or electron beam to form the metal part such that at least one or more portions of the metal part have a critical amount of residual strain. The method also includes performing a heat treatment on the metal part that transforms the residual strain into substantially distributed coincidence site lattice (CSL) grain boundaries, low angle grain boundaries, or both in the metal part.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Influence of defects on the femtosecond laser damage resistance of multilayer dielectric gratings

Multilayer dielectric (MLD) gratings with high diffraction efficiency and a high laser-induced damage (LID) threshold for pulse compressors are key to scaling the peak and average power of chirped pulse amplification lasers. However, surface defects introduced by manufacturing, storage, and handling processes can reduce the LID resistance of MLD gratings and impact the laser output. The underlying mechanisms of such defect-initiated LID remain unclear, especially in the femtosecond regime. In this Letter, we model dynamic processes in interactions of a 20-fs near-infrared (NIR) laser pulse and a MLD grating design in the presence of cylindrically symmetrical nodules and particle contaminants and cracks at the surface. Utilizing a dynamic model based on a 2D finite difference in time domain (FDTD) field solver coupled with photoionization, electron collision, and refractive index modification, we study the simulation results for the damage site distribution initiated by defects of various types and sizes and its impact on the LID threshold of the grating design.

Zhang, Simin (ORCID:0000000174948230)↗
DOE OSTI2023

3D Printing of Solar Absorber Tube with Internal/External Structures for Heat Transfer Enhancement and Temperature Leveling using Additive Manufacturing Technology

In this project, to tackle the technical obstacles, we utilized Laser Additive Alloying (LAA), an additive manufacturing (AM) technology, to 3D print the entire absorber tube with optimized helical fins to improve heat transfer at the expense of minimized pressure drop increase. The 3D printed absorber tubes can increase the uniformity of circumferential temperature distribution, reduced the thermal stresses, decrease the heat loss, and reach the target receiver thermal efficiency.

14 SOLAR ENERGY↗
DOE OSTI2024

High Temperature Additive Architectures for 65% Efficiency (Final Technical Report)

This project aimed to develop advanced high-temperature additive components that contribute towards the DOE’s goal for advanced gas turbines that are capable of at least 65% efficiency in combined cycle application. The objective was to leverage state-of-the-art additive manufacturing to develop an innovative stage 1 turbine nozzle (S1N) that can provide cooling flow savings while maintaining the component durability expected in today’s gas turbines. The program had two phases. Phase I was a conceptual phase for novel advanced cooling designs enabled by additive manufacturing, as well as proposals for validation. Phase II included execution of the Phase I conceptual design, including manufacturing of prototype hardware and validation within an environment that is similar to engine operation. During Phase I of the program, the team devised a concept to reduce cooling air usage. The cooling air used in the side walls is filmed out along the side walls, while the cooling air used in the airfoil is eventually directed to near-wall channels and exits holes along the airfoil trailing end. During this program, the team performed additive trials to analyze the geometric limitations of additive manufacturing. This helped the team understand minimum wall thicknesses, hole sizes, and cooling channel dimensions among other limits. Phase II of this program pushed GE Vernova beyond its previous experience of designing and manufacturing an additively manufactured hot gas path component. Modern hot gas path components utilize material chemistries that are traditionally hard to weld, such as cast Renè 108, and exhibit solidification cracking when additively manufactured using Direct Metal Laser Melting (DMLM). Note that AM108 is a powder form of Renè 108. A S1N with advanced cooling is larger and more complex than parts previously built by additive manufacturing and required new learnings to resolve risks around solidification cracking. Finally, the team validated the design in a combustion rig that replicated operation in a gas turbine. In order to properly quantify the benefits of the new additive design, a baseline was also tested in the rig and operated under the same conditions. In addition, an uncertainty analysis was done to quantify any sources of error that could impact the results. At the end of the validation effort, it was determined that the additive nozzle exceeded the 15% reduction in cooling flow goal even with the worst-case assumptions for uncertainty.

03 NATURAL GAS↗
NASA NTRS2026

Evaluation of Superalloy 718 Additively Manufactured Lattice Blocks

Lattice block structures made up of high temperature superalloys could offer advantages in density, efficiency, and tailored properties. Three candidate lattice designs were screened through additive manufacturing of superalloy 718. Laser powder bed fusion was applied with 718 powder to produce lattice blocks for three-dimensional octahedral unit cell designs of three heights. As-designed versus additively manufactured 718 lattices were compared, including structural dimensions, densities, defects, grain structures, crystallographic texture, and surface residual stresses. Manufactured lattice I diverged the most from its design, with both corner and center nodes merged into continuous columns. Manufactured lattice III came closest to its design, though the actual nodes and struts were still larger in cross section than in the design. Only modest grain coarsening and negligible chemical segregation were observed for all three designs, suggesting uniform thermo-physical and mechanical properties are possible. Significant tensile residual stresses were present at the surface of the manufactured blocks, with highest stresses in the building direction. Current findings indicate this concept could produce useful superalloy structures for high-temperature-capable static components requiring tailored density, and thermo-physical/mechanical properties.

super alloys↗
DOE OSTI2020

Evolution of AISI 304L stainless steel part properties due to powder recycling in laser powder-bed fusion

Selective laser melting (SLM) is a powder-bed fusion process in Additive Manufacturing (AM) that uses a laser beam to selectively fuse layers of powder into near net-shape components with little porosity. However, inconsistencies in the part properties due to the presence of defects in as-built components has hindered the widespread adoption of SLM for industrial applications forcing researchers to study the sources of variation for quality control purposes. A critical area suspected of creating variation in the part properties is the feedstock, where batch-to-batch differences as well as changes in the powder properties with reuse have the potential to affect performance. During processing, laser spatter and condensate eject from the melt pool and deposit into the powder-bed surrounding the parts. These particulates, more commonly known as ejecta, differ morphologically and chemically from the virgin powder compromising its reusability. In this study, 304L stainless steel powder was recycled for a total of 5 times through a systematic approach aimed at accelerating powder degradation to reveal the influence on both the tensile and impact toughness properties. Through analysis of variance (ANOVA), it was found that tensile properties did not change with reuse, while the impact toughness showed a steady decline illustrating the differences in static and dynamic part properties due to powder recycling.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Hybrid manufactured dynamometer for cutting force measurement

This paper describes a two-step (additive + subtractive) hybrid manufacturing approach for a laser powder bed fusion 316L stainless steel constrained-motion cutting force dynamometer (PBF CMD). The purpose of the research is to produce a near-net shape metallic dynamometer via additive manufacturing (AM) with post-processing by machining and wire-EDM to achieve the desired surface finish and performance. A cutting force comparison is presented with a commercially-available dynamometer.

36 MATERIALS SCIENCE↗
NASA NTRSDate not supplied

Evaluations of Additively Manufactured Superalloy Lattice Blocks

Cast lattice block structures made up of high-temperature superalloys were previously shown to offer advantages in density, efficiency, and tailored properties. However, inconsistencies in casting die-fill, composition, and microstructure were identified as persistent issues with the casting process path. Three candidate lattice designs were screened through additive manufacturing of a superalloy. Laser powder bed fusion was applied with superalloy powder to produce lattice blocks for three-dimensional octahedral unit-cell designs of three heights. Properties of the structural designs versus additively manufactured lattices were compared, including structural dimensions, densities, defects, grain structures, crystallographic texture, and surface residual stresses. Findings indicate this concept could produce useful superalloy structures for high-temperature-capable static components requiring tailored density, and thermophysical and mechanical properties.

superalloy↗
DOE OSTI2025

A mechanistic study on environment gas in laser powder bed fusion

A variety of protective or reactive environmental gases have recently gained growing attention in laser-based metal additive manufacturing (AM) technologies due to their unique thermophysical properties and the potential improvements they can bring to the build processes. However, much remains unclear regarding the effects of different gas environments on critical phenomena in laser AM, such as rapid cooling, energy coupling, and defect generation. Through simultaneous high-speed synchrotron x-ray imaging and thermal imaging, we identify distinct effects of two environmental gases in laser AM and gained a deeper understanding of the underlying mechanisms. Compared to the commonly used protective gas, argon, it is found that helium has a negligible effect on cooling the part. However, helium can suppress unstable keyholes by decreasing effective energy absorption, thus mitigating keyhole porosity generation and reducing pore size under certain processing conditions. In conclusion, these observations provide guidelines for the strategic use of environmental gases in laser AM to produce parts with improved quality.

36 MATERIALS SCIENCE↗
NASA NTRS2024

Correlations of Additive Manufacturing Model-Based Process Metrics With Spatter-Induced Porosity in the Powder Bed Fusion-Laser Beam/Metallic Process

Components fabricated using the powder bed fusion laser beam metallic (PBF-LB/M) additive manufacturing (AM) process comprise a multitude of sequential weld passes. Qualifying materials for components in critical applications requires a thorough understanding of pertinent processing-microstructure-property relationships. Porosity defects have a strong adverse effect on the mechanical properties of a material. The morphology of porosity defects created by lack of fusion in PBF-LB/M often exhibit high aspect ratios that can act as stress concentrators and become crack initiation sites. The occurrence of spatter induced porosity is studied using synchronized AM model-based process metrics and porosity measured by high-resolution X-ray computed tomography. A novel AM process metric is introduced to quantify the relative exposure to spatter ejecta impacts and incorporation throughout the sequence of the PBF-LB/M process. Further characterization using optical metallography and scanning electron microscopy indicated that both keyhole and lack of fusion porosity correlated statistically with the spatter ejecta impact field of the PBF-LB/M process. Both keyhole and lack of fusion porosity can be predicted by the spatter exposure process metric, which can be exploited to control the fusion sequence.

Additive Manufacturing↗