SEARCH · Engineering Papers
Results for “Graphite Properties”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Properties of Low-Expansion Laminates
Laminate elastic constants and coefficients of thermal expansion calculated for near-zero-expansion graphite/aluminum and graphite/ magnesium composites. Report presents results in graphic form for these properties as function of laminate angle and fiber volume fraction for four high-modulus continuous-pitch fiber.
On the thermal oxidation of nuclear graphite relevant to high-temperature gas cooled reactors
Thermal oxidation of nuclear graphite components is highly undesirable because it can cause structural and property degradation that negatively affect a reactor's intended operation. In this work, the body of knowledge of nuclear graphite oxidation is highlighted, including when O 2 , H 2 O, and/or CO 2 are the oxidant. Oxidation conditions relevant to high-temperature gas-cooled reactors (i.e., when oxidation could occur either as an acute or chronic phenomenon) are emphasized. Here, the objective is to summarize graphite oxidation data in a practical and accessible way to inform future research and regulatory requirements. Although each grade of nuclear graphite is different, the oxidation mechanism has underlying commonalities. Although oxidation behavior is grade dependent, the general temperature dependence is well described by a sequence of elementary steps which become rate limiting. Because the regime transition temperature depends on sample microstructure, size, and oxidant supply rate, extrapolating results beyond the experimental range should be done cautiously. Gravimetric oxidation rate measurements generally replicate well. However, caution must be exercised when rates are estimated by other methods or for samples that deviate significantly in size. Air oxidation data for IG-110, NBG-18, and PCEA graphite is critically reviewed to emphasize this point. Despite the amount of experimental data, gaps remain. Sample size and shape effects are not fully explained. Data on the oxidant penetration depth are insufficient. Analytical assessments demonstrate that lower temperature oxidation does not necessarily imply that oxidation is uniform throughout the bulk. Oxidation occurs faster at higher temperature but is more localized to the exposed surface. Paradoxically, at equal mass loss percentage, low temperature oxidation leads to greater property degradation than at high temperature. The isolated effect of oxidation is important; however, a gap remains in the systematic understanding of any potential effect of neutron irradiation on graphite structure and reactivity.
A Study of Space Environment Effect on Highly Thermally Conductive Hybrid Carbon Fiber Polymer Composites
A set of novel highly thermally conductive hybrid carbon fiber (CF) polymer composites has been developed for lightweight thermal radiator applications in space missions. This study investigates the effects of the space environment on these materials following exposure in low-Earth orbit (LEO) during the Materials International Space Station Experiment (MISSE)-17 flight mission, where samples experienced 159 days of combined atomic oxygen (AO), ultraviolet (UV) radiation, high vacuum, space radiation and thermal cycling. Post-flight characterization included weight loss, surface morphology, thermo-optical properties, molecular structures, glass transition temperature, thermal degradation and thermal conductivity analyses. The pyrolytic graphite sheet (PGS) samples exhibited negligible weight loss, stable thermo-optical property, and only minor oxidation signature on the exposed surface. Although AO erosion of the epoxy polymer matrix was evident, carbon nanotube (CNT)-infused PGS/CF epoxy composites retained high thermal emissivity and preserved their high thermal conductivities. These results demonstrate that the novel highly thermally conductive hybrid CF composites possess strong environmental resilience and are promising candidates for lightweight thermal radiators and thermal management components in future space exploration missions.
Progress Towards a Titanium-Zirconium-Molybdenum Alloy Coreblock Prototype Using Powder Bed Fusion
Microreactor designs make use of a coreblock for structural stability allowing for these devices to provide powder generation while being portable and inherently safe. In order to maximize energy output of the microreactors, materials must be able to withstand high temperature without melting and without substantial decreases in mechanical properties. As simultaneous projects looking at steels, graphite, and other materials are on-going, this work package will investigate titanium – zirconium – molybdenum alloy (TZM) as it allows for potentially higher microreactor operating temperatures than traditional reactor materials such as stainless steel. Notably, this alloy was developed in the 1960s for use in rockets and has a very high melting point (2623°C) but is difficult to form, machine and join. With limited needs in aerospace, literature is appropriately sparce in looking at the AM of TZM (examples include [1,2]). However, the properties appear to be an excellent match for the needs of the microreactor coreblock leading to the current project. In addition, small washers form the bulk of TZM parts needed in aerospace while the microreactor community was looking at larger, more complex parts. Therefore, AM of TZM is being explored to enable near – net shape of components with the needed complexity to impact the nuclear energy field.
Zeolites interactions with microwaves during methane non-oxidative coupling
Microwave-zeolite interactions during direct non-oxidative reactions of methane were studied using three H-ZSM-5 zeolites with different concentrations of Bronsted acid sites. The formation of C 2 and aromatic hydrocarbons increased with increasing surface acidity. When compared to conventional heating, the microwave reaction produced less carbon with higher thermal stability. The increase in diffraction shifts and the decrease in its surface area of microwave-reacted zeolite suggested that the carbon started depositing inside the micropores rather than on the external surfaces. Inhomogeneous carbon deposits with filamentous carbon whiskers were observed under microwave compared to homogeneous spherical carbon deposits on the conventionally reacted sample. The dielectric properties and Raman analysis suggested that the graphitic nature and the thermal stability of deposited carbon increased with zeolite surface acidity under microwave. We believe that this is a very important study for designing microwave active zeolite-based catalysts with a low affinity towards carbon formation.
Prospective Life Cycle Assessment of Synthetic Graphite Manufactured via Electrochemical Graphitization
Lithium-ion batteries (LIBs) are expected to play a crucial role in meeting many of the clean energy-related goals. Due to its electrical properties such as good conductance, chemical inertness, and corrosion resistance, graphite is a very popular anode for LIBs. Traditional methods of producing battery-grade graphite (high purity >99%) include processing naturally mined graphite or manufacturing synthetic graphite via the Acheson process, which converts soft amorphous carbons such as petroleum coke into graphite by subjecting it to high temperature (up to 3000 °C) for prolonged periods of times (3–5 days). However, due to a lack of abundant high purity natural graphite sources, synthetic graphite is the preferred choice for many LIBs. A new synthetic electrochemical graphitization method that subjects the amorphous carbon precursor submerged in a molten salt mixture to a constant cathodic polarization (against a graphitic anode) has been discovered that has significantly lower graphitization temperatures (~800 °C) and reduced graphitization time (3–6 h). Furthermore, the method can accept a higher variety of carbon precursors compared to the Acheson process. A prospective life cycle assessment (LCA) is conducted on this new method and compared against the traditional processes. The laboratory-scale demonstration of the method is used to build an inventory, which through various assumptions is scaled up to a commercial scale. An additional scenario is also considered with a biomass-derived carbon precursor for the graphite. The results from the LCA show that while the laboratory scale process is similar to the Acheson process and natural flake graphite in terms of impact, the scaled-up process is drastically better than the Acheson process in all environmental categories. Using a coconut shell-derived biomass precursor has a higher impact due to its manufacturing in Indonesia, as the Indonesian energy grid is highly fossil fuel dependent. Therefore, the biomass carbon may have a higher impact than petroleum coke dependent on the location of production of biomass-derived carbon black. The LCA has identified the molten salt—CaCl 2 —as a potential hotspot and suggests other salts should be considered. Accordingly, the new method shows promise in this early stage LCA in improving the environmental performance of graphite (and by relation LIBs) and therefore needs to be explored more in terms of its commercial viability.
Utilization of Carbon Supply Chain Wastes and Byproducts to Manufacture Graphite for Energy Storage Applications
This project explored how coal and waste coal can be transformed into high-value graphite used in batteries for electric vehicles and power grids. A manufacturing technique that converts coal into carbon foam and subsequently graphite was developed and refined to improve the thermal and mechanical properties of the resulting materials. Cost-effectiveness and environmental impacts were also evaluated. Coal-derived graphite, especially when processed at high temperatures, was shown to perform comparably to commercial graphite in battery tests. Advanced computer simulations were used to model battery behavior and predict long-term performance, demonstrating that coal-based graphite has the potential to support electric vehicle deployment while reducing reliance on imported materials. This work offers a promising pathway for cleaner energy storage solutions and creates economic opportunities for coal-reliant communities by generating new uses for mining byproducts.
Graphite and ablative material response to CO2 laser, carbon-arc, and xenon-arc radiation
The behavior was investigated of graphite and several charring ablators in a variety of high-radiative heat-flux environments. A commercial-grade graphite and nine state-of-the-art charring ablators were subjected to various radiative environments produced by a CO2 laser and a carbon arc. Graphite was also tested in xenon-arc radiation. Heat-flux levels ranged from 10 to 47 MW/sq m. Tests were conducted in air, nitrogen, helium, and a CO2-N2 mixture which simulated the Venus atmosphere. The experimental results were compared with theoretical results obtained with a one-dimensional charring-ablator analysis and a two-dimensional subliming-ablator analysis. Neither the graphite nor the charring ablators showed significant differences in appearance or microstructure after testing in the different radiative environments. The performance of phenolic nylon and graphite was predicted satisfactorily with existing analyses and published material property data. Good agreement between experimental and analytical results was obtained by using sublimation parameters from a chemical nonequilibrium analysis of graphite sublimation. Some charring ablators performed reasonably well and could withstand radiative fluxes of the level encountered in certain planetary entries. Other materials showed excessive surface recession and/or large amounts of cracking and spalling, and appear to be unsuitable for severe radiative environments.
Carbon-rich ceramic composites from ethynyl aromatic precrusors
A number of polyfunctional aromatic acetylenes thermally polymerize at low temperatures (180 C) and pyrolyze with greater than 90 char yield. In nonoxidizing environments, they are thermally stable to 1450 C. These monomers were chosen as the basis of a model system to study the fabrication and mechanical properties of continuous filament ceramic matrix composite. Composites were fabricated from aryl poly(acetylenes), SiC particulate filler and graphite, Avco SiC, Nicalon and Nextel fibers. Microstructure, physical and mechanical properties are reported.
The influence of buoyant forces and volume fraction of particles on the particle pushing/entrapment transition during directional solidification of Al/SiC and Al/graphite composites
Directional solidification experiments in a Bridgman-type furnace were used to study particle behavior at the liquid/solid interface in aluminum metal matrix composites. Graphite or silicon-carbide particles were first dispersed in aluminum-base alloys via a mechanically stirred vortex. Then, 100-mm-diameter and 120-mm-long samples were cast in steel dies and used for directional solidification. The processing variables controlled were the direction and velocity of solidification and the temperature gradient at the interface. The material variables monitored were the interface energy, the liquid/particle density difference, the particle/liquid thermal conductivity ratio, and the volume fraction of particles. These properties were changed by selecting combinations of particles (graphite or silicon carbide) and alloys (Al-Cu, Al-Mg, Al-Ni). A model which consideres process thermodynamics, process kinetics (including the role of buoyant forces), and thermophysical properties was developed. Based on solidification direction and velocity, and on materials properties, four types of behavior were predicted. Sessile drop experiments were also used to determine some of the interface energies required in calculation with the proposed model. Experimental results compared favorably with model predictions.
ASME Code Development - Nonmetallics
ASME Code Development - Nonmetallics slides to include behavior models, licensing & code, graphite R&D Program, As-Fab'd Properties, Mechanisms and Analysis, and Irradiation. Discussion on where these fit into Irradiation behavior, Ceramic Composites, Design, and Component Failure.
Research on graphite reinforced glass matrix composites
A broad group of fibers and matrices were combined to create a wide range of composite properties. Primary material fabrication procedures were developed which readily permit the fabrication of flat plate and shaped composites. Composite mechanical properties were measured under a wide range of test conditions. Tensile, flexure mechanical fatigue, thermal fatigue, fracture toughness, and fatigue crack growth resistance were evaluated. Selected fiber-matrix combinations were shown to maintain their strength at up to 1300 K when tested in an inert atmosphere. Composite high temperature mechanical properties were shown to be limited primarily by the oxidation resistance of the graphite fibers. Composite thermal dimensional stability was measured and found to be excellent.
Viewing is understanding: Graphite microstructure effects on infiltrated molten salt distribution revealed by 3D neutron tomography
Molten salt infiltration in the pore network of nuclear graphite may cause unwanted changes to graphite's local structure and mechanical and thermal properties. A detailed and comprehensive understanding of molten salt intrusion (distribution across sample cross section and penetration depth) is needed to assess its effects. Here, in this work, we report on an improved methodology for the use of neutron imaging (computed tomography) to evaluate salt penetration and distribution of a wide range of graphite grades with diverse microstructures. Neutron tomography data were acquired on the same graphite sample before and after salt intrusion; the 3D reconstructed volumes were digitally co-registered and subtracted. The difference in neutron attenuation coefficient represents direct visualization of FLiNaK (LiF–NaF–KF) salt distribution in the salt-impregnated graphite samples. This improved methodology was applied to investigate the effect of exposure times (12 h and 336 h) and of graphite microstructure when exposed to FLiNaK at 750 °C and 3 bar (gauge) pressure, starting from flowing argon at near atmospheric pressure. The results show that medium-grained and fine-grained graphites evolve to equilibrium at significantly different rates: fast salt uptake in medium-grained graphites produces salt deposits throughout the volume of graphite specimens, whereas salt infiltration in fine-grained graphites is much slower and limited to exposed surfaces.
Metallization of diamond
Experimental discovery of ultralarge elastic deformation in nanoscale diamond and machine learning of its electronic and phonon structures have created opportunities to address new scientific questions. Can diamond, with an ultrawide bandgap of 5.6 eV, be completely metallized, solely under mechanical strain without phonon instability, so that its electronic bandgap fully vanishes? Through first-principles calculations, finite-element simulations validated by experiments, and neural network learning, we show here that metallization/demetallization as well as indirect-to-direct bandgap transitions can be achieved reversibly in diamond below threshold strain levels for phonon instability. We identify the pathway to metallization within six-dimensional strain space for different sample geometries. We also explore phonon-instability conditions that promote phase transition to graphite. These findings offer opportunities for tailoring properties of diamond via strain engineering for electronic, photonic, and quantum applications.
Preparation of Mesophase Pitch Feedstock for Carbon Fiber
A filtration process of the low cost mesophase pitch developed by Advanced Carbon Products, LLC (ACP) was developed. The mesophase pitch was melt spun into fiber at the University of Kentucky Center for Applied Energy Research (UKY), and converted to carbon fiber. The melt spinning process was moderately stable, but resulted in some void structure in the green fibers. The tensile properties of the resulting carbon fibers, after graphitization heat treatment, were tested yielding a modulus value of approximately 560 GPa or 81 MSI. This demonstrated that a high modulus graphitic carbon fiber is certainly possible from the ACP 20 mesophase pitch. For future work, a better balance between the softening point temperature, the spinning temperature, and filtering must be met to reduce the volatiles generated in the pitch during spinning. This would reduce voids in the fiber, facilitate spinning, and generate finer, higher performance graphitic fiber.
Graphite fiber composites at cryogenic temperatures
Graphite fiber resin composites physical and mechanical properties at ambient and cryogenic temperatures, discussing unidirectional ring and bar specimens and filament wound pressure vessels
Infrared emission from ultracompact H II regions
Models of circumstellar dust shells around ultracompact (UC) H II regions were constructed that accurately fit the observed IR flux distributions. The models assume spherically symmetric dust shells illuminated by stars whose bolometric luminosity is inferred from the integrated FIR flux densities. Assuming ionization by a single zero age main sequence (ZAMS) star, the relations of Panagia were used to infer the stellar radius and effective temperature for a given luminosity. The grain mixture in the dust shell consists of bare graphite and silicate grains with the optical properties of Draine and Lee and the size distribution of Mathis et al. The computer code of Wolfire et al was used to solve the radiative transfer equations through a spherical dust shell. The model provides monochromatic luminosities, dust temperatures, and opacities through the shell. Aside from the stellar and dust properties, the only other input parameters to the model are the distance to the shell, the form of its density distribution, and its outer radius. Predictions of the model are compared with observations of a typical UC H II region and the run of dust temperature with radius and the optical depth with frequency are discussed.