Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “emission lines”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Multi-energy calibration of a PILATUS3 CdTe detector for hard x-ray measurements of magnetically confined fusion plasmas

A multi-energy hard x-ray pin-hole camera based on the PILATUS3 X 100K-M CdTe detector has been developed at the Princeton Plasma Physics Laboratory for installation on the Tungsten Environment in Steady State Tokamak. This camera will be employed to study thermal plasma features such as electron temperature as well as non-thermal effects such as fast electron tails produced by a lower hybrid radiofrequency current drive and the birth of runaway electrons. The innovative aspect of the system lies in the possibility of setting the threshold energy independently for each of the ~100k pixels of the detector. This feature allows for the measurement of the x-ray emission in multiple energy ranges with adequate space and time resolution (~1 cm, 2 ms) and coarse energy resolution. In this work, the energy dependence of each pixel was calibrated within the range 15 keV–100 keV using a tungsten x-ray tube and emission from a variety of fluorescence targets (from yttrium to uranium). The data corresponding to pairs of K α emission lines are fit to the characteristic responsivity (“S-curve”), which describes the detector sensitivity across the 64 possible energy threshold values for each pixel; this novel capability is explored by fine-tuning the voltage of a six-bit digital-analog converter after the charge-sensitive amplifier for each of the ~100k pixels. Here, this work presents the results of the calibration including a statistical analysis. It was found that the achievable energy resolution is mainly limited by the width of the S-curve to 3 keV–10 keV for threshold energies up to 50 keV, and to ≥20 keV for energies above 60 keV.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Improved imaging using Mn He- α x rays at OMEGA EP

In this paper, we report on a crystal based x-ray imaging system fielded at the OMEGA EP laser facility. This new system has a pointing accuracy of +/100 μm, a temporal resolution down to 100 ps (depending on backlighter characteristics), variable magnification, and a spatial resolution of 21.9 µm at the object plane at a magnification of 15×. The system is designed to use a crystal along the crystal plane that satisfies the Bragg condition for the x ray of interest. The thin crystal is then bent into a spherical geometry and attached to a glass backing substrate to hold it in the diagnostic, and the x rays are imaged onto a charge coupled device. We report on data acquired with the new Los Alamos National Laboratory supplied spherical quartz crystal to image the Mn He-α 6.15 keV line emission.

Fiedler Kawaguchi, C. (ORCID:0000000175522370)↗
DOE OSTI2021

The design of a photoionization front experiment using the Z-Machine as a driving source and estimated measurements

Radiation-driven heat fronts are present in the early universe during reionization, the circumstellar medium of supernovae, and in high-energy-density physics experiments. Dedicated experiments to observe and diagnose the behavior of these types of heat fronts can improve our understanding of these phenomena. A simulation study of photoionization fronts using the HELIOS-CR radiation hydrodynamics code provides an experimental design for the Z-Machine at Sandia National Laboratory using a measurement-calibrated input radiation flux to drive the photoionization front. The simulations use detailed atomic physics and non-diffusive radiation transport in 1D to determine an optimal gas pressure of 0.75 atm for an experiment in N gas as well as the effects of increasing the thickness of the window that seals the gas cell. Post-processing of these simulations demonstrates that ratios of atomic rate coefficients place the heat front in a physics regime where photoionization dominates the energy deposition. Here, to see the sensitivity of the simulations to changes in the model and spatial grid, this analysis performed resolution, atomic model detail, and radiation transport angular grid studies showing less than 10% deviation from the nominal model for increased complexity, when possible. An effort to emulate 3D geometric effects on the radiation flux using an artificial attenuation scheme has shown that, even for conservative estimates of the flux, simulations still produce a photoionization front. Estimations of a streaked, visible spectroscopy measurement using SPECT3D showed that line emission measurements are present early in time and that later in time thermal emission should become dominant.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Experimental observations of detached bow shock formation in the interaction of a laser-produced plasma with a magnetized obstacle

The magnetic field produced by planets with active dynamos, like the Earth, can exert sufficient pressure to oppose supersonic stellar wind plasmas, leading to the formation of a standing bow shock upstream of the magnetopause, or pressure-balance surface. Scaled laboratory experiments studying the interaction of an inflowing solar wind analog with a strong, external magnetic field are a promising new way to study magnetospheric physics and to complement existing models, although reaching regimes favorable for magnetized shock formation is experimentally challenging. This paper presents experimental evidence of the formation of a magnetized bow shock in the interaction of a supersonic, super-Alfvenic plasma with a strongly magnetized obstacle at the OMEGA laser facility. The solar wind analog is generated by the collision and subsequent expansion of two counterpropagating, laser-driven plasma plumes. The magnetized obstacle is a thin wire, driven with strong electrical currents. Hydrodynamic simulations using the FLASH code predict that the colliding plasma source meets the criteria for bow shock formation. Spatially resolved, optical Thomson scattering measures the electron number density, and optical emission lines provide a measurement of the plasma temperature, from which we infer the presence of a fast magnetosonic shock far upstream of the obstacle. Proton images provide a measure of large-scale features in the magnetic field topology, and reconstructed path-integrated magnetic field maps from these images suggest the formation of a bow shock upstream of the wire and as a transient magnetopause. Finally, we compare features in the reconstructed fields to two-dimensional MHD simulations of the system.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Development of an x-ray radiography platform to study laser-direct-drive energy coupling at the National Ignition Facility

A platform has been developed to study laser-direct-drive energy coupling at the National Ignition Facility (NIF) using a plastic sphere target irradiated in a polar-direct-drive geometry to launch a spherically converging shock wave. To diagnose this system evolution, eight NIF laser beams are directed onto a curved Cu foil to generate Heα line emission at a photon energy of 8.4 keV. These x rays are collected by a 100-ps gated x-ray imager in the opposing port to produce temporally gated radiographs. The platform is capable of acquiring images during and after the laser drive launches the shock wave. A backlighter profile is fit to the radiographs, and the resulting transmission images are Abel inverted to infer radial density profiles of the shock front and to track its temporal evolution. Here, the measurements provide experimental shock trajectories and radial density profiles that are compared to 2D radiation-hydrodynamic simulations using cross-beam energy transfer and nonlocal heat-transport models.

47 OTHER INSTRUMENTATION↗
DOE OSTI2022

Design study of an edge current density diagnostic using new high-performance single-channel beam emission spectrometers at DIII-D

A novel Motional Stark Effect spectroscopy system has been designed for application at the DIII-D tokamak. The system is optimized for studies of the poloidal and toroidal magnetic field in the plasma pedestal region with frame rates of up to 10 kHz. Further, light from an existing high-photon-throughput collection lens is analyzed using four single-channel f/2.8 Czerny–Turner spectrometers that use custom-made lens systems instead of mirrors. Each spectrometer has two separate outgoing legs and is operated in a positive grating order, which allows for simultaneous observations of D-alpha and D-beta spectra. Forward modeling using the code FIDASIM shows a radial resolution of the system close to 0.6 cm and sufficiently good spectral resolution when masking the high throughput light collection lens in the horizontal direction to avoid overly strong Doppler broadening of beam emission lines. Moreover, a detailed sensitivity study considering realistic levels of readout and photon noise shows that the poloidal and toroidal magnetic field strengths can be inferred with an uncertainty of less than 1%, which will allow the inference of changes of the plasma current during transient events.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Fundamental optical transitions in hexagonal boron nitride epilayers

Fundamental optical transitions in hexagonal boron nitride (h-BN) epilayers grown on sapphire by metal–organic chemical vapor deposition (MOCVD) using triethylboron as the boron precursor have been probed by photoluminescence (PL) emission spectroscopy. The low temperature (10 K) PL spectrum exhibits two groups of emission lines. The first group includes the direct observation of the free exciton and impurity bound exciton (BX) transitions and phonon replicas of the BX transition, whereas the second group is attributed to the direct observation of the band-to-band transition and its associated phonon replicas. The observations of zero-phonon lines of the band-to-band and exciton transitions, which are supposedly forbidden or “dark” in perfect h-BN crystals, result from a relaxed requirement of momentum conservation due to symmetry-breaking in the presence of high concentrations of impurities/defects and strain, which in turn provided more deterministic values of the energy bandgap (E g ), exciton binding energy (E x ), and binding energy of impurity bound excitons (E BX ) in h-BN epilayers. Excitonic parameters of h-BN epilayers grown by MOCVD, carbon-free chemical vapor deposition, and high purity h-BN bulk materials are compared and discussed. The present results, together with available information in the literature, represent a significant improvement in the understanding of the fundamental optical properties and excitonic parameters of h-BN ultrawide bandgap semiconductors.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Quantum fluctuations in dense plasma simulations

Molecular dynamics (MD) simulations are a powerful tool for modeling warm and hot dense matter. Density functional theory (DFT) MD simulations are often preferred in dense plasmas in order to accurately model quantum electronic structure. However, DFT-MD simulations neglect interaction effects due to fluctuations in excited states. In this work, we present an MD approach that uses excited state method pseudoatoms to run dense plasma simulations with many different core-electron configurations at classical MD speeds. We also allow for transitions between different configurations in our simulations and find that these fluctuations are especially important for highly excited states. Our results suggest that finite configuration lifetimes that are comparable to the inverse ion plasma frequency need to be accounted for in order to accurately model ion distributions in dense plasma simulations. We also demonstrate that excited state fluctuations have a direct impact on ion plasma microfields, generate different plasma microfields for different excitation levels, and thereby induce absorption–emission line shape asymmetries even in steady-state plasmas.

36 MATERIALS SCIENCE↗
DOE OSTI2024

The Electron Spectro-Microscopy (ESM) Beamline at NSLS-II

Photoelectron spectroscopy is a primary tool for the study of the electronic structure of materials and the chemical composition of surfaces. High-resolution angle-resolved photoemission spectroscopy (ARPES) has the unique ability to map the energy bands in momentum space. Furthermore, going beyond the single particle picture, the self-energy corrections caused by correlations in solids can be extracted from the analysis of the emission line shape. The current level of refinement, in terms of energy and angular resolution (ΔE < 1 meV, Δθ < 0.1°), makes the technique sensitive to the lowest energy excitations and the dynamics of electrons, which in turn virtually determine all the macroscopic properties of any system and govern the chemical, electrical, magnetic, and physical processes. Similarly important, X-ray photoelectron microscopy (XPEEM), combined with the low-energy electron microscopy (LEEM), is indispensable in probing the complexity of chemical, structural, electronic and magnetic properties of surfaces and shallow interfaces, with the spatial resolution of few tens of nanometer (nm). The Electron-Spectro-Microscopy beamline (ESM) has been recently commissioned at NSLS-II and is now in operation. The primary spectroscopic technique is photoemission, performed over a wide energy range with control of light polarization and in a variety of flux/resolution conditions. The beamline has two experimental end stations that allow to perform ARPES and XPEEM/LEEM, separately. The ARPES end station focuses on high energy-resolution work, with spot-size of a few microns. The XPEEM/LEEM end station is a full-field microscope (XPEEM) operating either with the synchrotron generated X-rays (XPEEM), or with an internal electron gun (LEEM). Spatial resolution is crucial in studies of newly synthesized complex materials since they are often initially available only as small specimens (typically micron size). Furthermore, chemical inhomogeneities on surfaces are often an integral part of surface chemical processes. Finally, the ESM beamline with X-ray spots of few microns is optimized to study the electronic structure of novel materials with microscopy capabilities.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Reconfiguration of an Electrothermal-Arc Plasma Source for In Situ PMI Studies

An electrothermal-arc plasma source (ET-Arc) has been developed to produce transient plasma heat and particle fluxes similar to those produced by edge localized modes onto divertor plasma-facing components in tokamaks. The ET-Arc utilizes a capacitive discharge to send current through a 4-mm-diameter, 9-cm-long capillary source liner. The liner material is ablated to form a high-velocity plasma jet that impacts the target downstream. With the current discharge circuit configuration, pulse lengths are 1 to 2 ms in duration and deliver heat fluxes of 0.25 to 2.1 GW m-2. The plasma was previously characterized with optical emission spectroscopy (OES) on helium emission lines. The He I line ratios were interpreted with collisional radiative analysis to calculate ne and Te. The electron temperature and electron density ranged from Te = 1 to 5 eV and ne = 1022 to 1028 electrons/m3, respectively.

Lindquist, Elizabeth G.↗
DOE OSTI2021

Contamination of argon x-ray spectra by tungsten and other elements commonly found in tokamaks

Here, emission lines which appear in the spectral ranges of ground state transitions from n> = 2 levels in He- and H-like argon ions are discussed. X-ray transitions from elements commonly found in tokamaks (tungsten, molybdenum, iron and sulphur) which radiate in the wavelength range from 3700–4000 mÅ are identified by comparison with atomic structure calculations. Individual lines from tungsten charge states in the vicinity of Zn-like W 44+ are documented, along with B-like Mo 37+ . The behaviour of line ratios as a function of electron temperature is examined, in support of the identifications.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Estimation of mean electron energy in helium surface ionization waves on dielectric substrates

Abstract The determination of basic plasma parameters in atmospheric pressure discharges is critical to advancing their use in applications. Atmospheric pressure plasma jets have found use in the fields of medicine, agriculture, material modification and others. Atmospheric pressure plasma jets often generate plasma surface ionization waves (SIW) which interact with and propagate over surfaces. Electrical diagnostics are challenging in SIW due to high collision frequencies and small scale of the plasma discharge. This work employs a passive optical emission line ratio technique to estimate the mean electron energy in SIW over planar dielectric substrates. The method uses an intensity ratio of two helium triplet lines: He( 3 3 S ) at 706.5 nm and He( 3 3 D ) at 587.56 nm. A collisional-radiative model is used to correlate line ratio to mean electron energy and determine dependencies on electron density and He/air gas mixture. Mean electron energies ranging from 3–8 eV are determined in He/air mixtures and are found to remain constant as the surface wave propagates radially. This work provides a 2D, time-resolved, mean electron energy diagnostic for surface ionization wave propagation and validation of numerical modeling in atmospheric pressure systems with spatially varying He/air gas mixtures. The model in question is designed for use with any He line ratio in the n = 3 excitation level.

Morsell, Joshua (ORCID:0000000331073002)↗
DOE OSTI2020

The effect of metastable atomic levels in neutral tungsten for erosion and impurity transport applications

Long-lived metastable states in neutral tungsten are shown to potentially impact measurements of tungsten erosion from plasma facing components. Time-dependent collisional radiative modeling of neutral tungsten is used to analyze the role of these states in tungsten emission and ionization. The large number of non-quasistatic atomic states in neutral tungsten can take on the order of milliseconds to reach equilibrium, depending on plasma conditions, causing erosion measurements to be affected by the metastable populations. Previous measurements using the 400.88 nm tungsten emission line could be affected by these non-quasistatic metastable effects. Therefore, a scheme for measuring the relative metastable fractions is proposed through simultaneous observation of multiple ultraviolet spectral lines of neutral W. The accuracy of gross erosion measurements could potentially be increased by inclusion of these previously unconsidered metastable effects.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

The achievement of the T e,div feedback control by CD 4 seeding on EAST

A multi-function divertor feedback control system has been built on Experimental Advanced Superconducting Tokamak (EAST) to treat the divertor heat load issue. With the real-time data of the Langmuir probes and the impurity seeding, the divertor electron temperature (T e,div ) is well controlled to achieve the partial detachment phase. The first trial of the CD 4 seeding for the T e,div reduction has been achieved on EAST long-pulse discharge. In the seeding phase, the T e,div was maintained close to 5 eV, and the surface temperature of the target plate (T surface,div ) had a reduction of about 150° C. The plasma stored energy had a reduction in the control phase, so it is necessary to find a way to keep the good plasma confinement in the next step. The CD 4 injection also mitigated the low hybrid wave coupling rate in some degree. The big volume of the CD 4 injection lifted the Greenwald density fraction from ~0.4 to ~0.7, which made the SOL into high recycling state. As a result, most of the injected carbon particles were in the high ionized state, and with the lower of the T e,div , the tungsten line emission was suppressed obviously.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Comparison of Doppler back-scattering and charge exchange measurements of E × B plasma rotation in the DIII-D tokamak under varying torque conditions

Measurements of the E × B toroidal angular velocity, $\omega_{E \times B}\,=\,E_\mathrm{r}/RB_\theta$ ($E_\mathrm{r}$ is the radial electric field, B θ is the poloidal magnetic field), are made using the Doppler back-scattering (DBS) and charge-exchange recombination (CER) spectroscopy diagnostics. DBS uses the Doppler shift of wavenumber-resolved density fluctuations while CER uses the Doppler shift of impurity emission lines to independently measure plasma parameters for calculating the local radial electric field. DBS and CER profiles of $\omega_{E \times B}$ as a function of normalized toroidal flux (ρ) are compared at various levels of neutral beam applied torque on the plasma. Under standard neoclassical theory $\omega_{E\times B}$ is a flux surface quantity, making it appropriate to compare across diagnostics. DBS and CER generally show good agreement when comparing $\omega_{E \times B}$ profiles at different levels of neutral beam injection-applied torque. Furthermore, the DBS values have close to the same precision as CER values when averaged over a similar time-scale and effects, such as prompt-torque are considered. DBS is able to observe the rapid ($\lt$10 ms) modification of the $E_\mathrm{r}$ profile by the diagnostic neutral beam 'blips'. This modification is most pronounced when the blip applies a large relative change in torque on the plasma. Overall, these results could have implications on transport analysis and suggests using DBS and CER in conjunction to constrain values of the E × B-shear (sometimes called $\gamma_{E \times B}$).

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

The effectiveness of D 2 pellet injection in reducing intra-ELM and inter-ELM tungsten divertor erosion rates in DIII-D during the Metal Rings Campaign

Abstract Edge localized modes (ELMs) in H-mode plasmas erode plasma-facing components (PFCs) and lead to impurities in the core, reducing confinement. This study analyzes D 2 pellet injection on the DIII-D fusion experiment used as an ELM mitigation technique applied during the 2016 tungsten Metal Rings Campaign to reduce W erosion during ELMs. The 400.9 nm photon wavelength line emission intensity of tungsten atoms (WI) filterscope channels and Langmuir probes were used to infer the gross erosion rate of tungsten-coated tiles installed in the divertor of DIII-D. D 2 mass injection rates ranging from 34 to 41 arbitrary units (A.U.) and no D 2 injection resulted in a similar total W erosion rate during ELMs (intra-ELM). On average, results show a 29% increase in the total gross W erosion rate with intermediate mass injection rates (∼13–23 A.U.) compared to the no pellets and the highest injection rate cases. On average, the fast D 2 mass injection rate cases had 15% less erosion in the inter-ELM phase than the case with no pellets. Generally, higher D 2 mass injection rates increased the ELM frequency, and the highest injection rates reduced the average erosion per ELM and fractional carbon impurities at the top of the pedestal by nearly 40% when compared to the no-pellet case. As expected, a higher D 2 pellet injection rate led to a higher plasma density and lower plasma temperature in the divertor. Additionally, an increasing divertor inter-ELM plasma electron density directly correlated to more frequent pellet injection and a decrease in both the average gross intra-ELM W erosion and the total gross intra-ELM W erosion rate. Simulations of intra-ELM erosion using the ‘free-streaming plus recycling model’ (FSRM) underestimate W erosion during pellet injection by about 30% on average. The discrepancies between the experimental measurements and the FSRM intra-ELM W erosion predictions are postulated to be due to C/W material mixing. A simple analytic mixed-material model is presented and results in better agreement with the experimental data. These results highlight the importance of incorporating the effects of a mixed-material layer in the analysis of PFC erosion.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Novel soft x-ray multi-energy camera to study thermal plasmas on WEST

A multi-energy soft x-ray (SXR) pinhole camera has been built, calibrated and deployed on the WEST tokamak to aid the study of thermal plasmas. This novel imaging diagnostic technique employs a 2D pixelated x-ray detector in which the lower energy threshold for photon detection can be adjusted independently on each pixel. This innovation allows the simultaneous measurement of x-rays with space, time and energy resolution. Measurements at lower energy (2–6 keV) dominated by tungsten line emission are used to estimate the tungsten concentration and the plasma ΔZ eff . Measurements at higher energy (11–18 keV), where only continuum emission is present, are employed to infer the plasma electron temperature. Other applications of this powerful diagnostic include the determination of the plasma SXR centroid vertical position, characterization of tungsten UFOs and various real-time measurements.

electron temperature↗
DOE OSTI2020

Dual wavelength operation of the GaSb-based Y-branch distributed Bragg reflector lasers near 2.1 μ m

The GaSb-based diode lasers operating simultaneously at two wavelengths near 2.1 μm have been designed and fabricated. The Y-branch devices used the 6th order distributed Bragg reflectors (DBR) to provide spectrally selective feedback. The laser active region contained two asymmetric quantum wells with allowed optical transitions between two lowest electron (e1 and e2) and top hole (hh1) subbands. The laser emission lines loosely matched the e1-hh1 and e2-hh1 optical transitions with separation corresponding to ~3.1 THz. Finally, the 10 μm wide deeply etched straight ridge DBR lasers demonstrated stable single mode operation with more than 50 mW of output power.

77 NANOSCIENCE AND NANOTECHNOLOGY↗