Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Dislocation structure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Structural and optical properties of cubic GaN on U-grooved Si (100)

Cubic GaN epitaxy on large-area U-grooved silicon (100) dies is demonstrated by metalorganic chemical vapor deposition, and its structural and optical properties are reported. Scanning electron, atomic force, and transmission electron microscopy studies reveal that cubic GaN shows no discernible threading dislocations and a low stacking fault density of 3.27 ± 0.18 × 10 4 cm –1 . Temperature-dependent photoluminescence studies reveal as-grown cubic GaN band edge emission internal quantum efficiency as 25.6% ± 0.9%. Selective etching of the low-temperature AlN buffer layer, SiO 2 sidewalls, and hexagonal-phase GaN is demonstrated, which increases the cubic GaN band edge emission internal quantum efficiency to 31.6% ± 0.8%. This increase is attributed to the decrease in the radiative recombination lifetime via the removal of defective hexagonal-phase GaN. Altogether, cubic GaN on U-grooved silicon with high structural and optical quality is reported, promising its suitability for next-generation devices.

36 MATERIALS SCIENCE↗
NASA NTRS1991

Hydride structures in Ti-aluminides subjected to high temperature and hydrogen pressure charging conditions

The distribution and chemistry of hydrides produced in single and dual phase alloys with a composition near TiAl have been investigated by using a combination of TEM and X-ray diffraction techniques. The alloys were exposed at 650 C to 13.8 MPa of gaseous H2 for 100 h. In the single-phase gamma alloy, large hydrides preferentially nucleated on the grain boundaries and matrix dislocations and a population of small hydrides was distributed throughout the matrix. X-ray and electron diffraction patterns from these hydrides indicated that they have an fcc structure with a lattice parameter of 0.45 nm. EDAX analysis of the hydrides showed that they were enriched in Ti. The hydrides were mostly removed by vacuum annealing at 800 C for 24 h. On dissolution of the hydrides, the chemistry of hydride-free regions of the grain boundary returned to the matrix composition, suggesting that Ti segregation accompanied the hydride formation rather than Ti enrichment causing the formation of the hydride.

Legzdina, D.↗
DOE OSTI2020

Structural damage and phase stability of Al 0.3 CoCrFeNi high entropy alloy under high temperature ion irradiation

In this study, an initially single phase high entropy alloy (HEA) Al 0.3 CoCrFeNi was irradiated by 3 MeV Au ions to a fluence of 6 × 10 15 cm –2 (~31 dpa at damage peak) at four different temperatures ranging from 250 °C to 650 °C. Transmission electron microscopy (TEM) and Atom probe tomography (APT) were employed to study the evolution of structural damage and phase stability with irradiation temperature. Al 0.3 CoCrFeNi exhibited a similar evolution of irradiation-induced defects with temperature as compared with conventional FCC alloys. At 250 °C and 350 °C, most of the visible irradiation-induced defects were faulted 1/3$\langle{111}\rangle$ dislocation loops. As the irradiation temperature increased to 500 °C, perfect 1/2$\langle{110}\rangle$ dislocation loops were observed along with the faulted loops. At the highest irradiation temperature 650 °C, only dislocation lines and networks could be observed. Regarding phase stability, the 3 MeV Au irradiation was observed to suppress the precipitation of (Ni, Al)-enriched nano clusters and the L12 ordered structure at irradiation temperatures 250 °C to 500 °C whereas precipitation of the B2 ordered structure was accelerated at 650 °C. This resulted in qualitatively opposite precipitation behavior between the ion irradiated damage region and unirradiated region at 500 °C and 650 °C. The opposite phase stability of the ion-irradiated damage region and unirradiated region at different temperatures is attributed to the competing effects of ballistic dissolution vs irradiation enhanced diffusion on precipitation.

36 MATERIALS SCIENCE↗
DOE OSTI2023

In-Situ X-Ray Imaging High Strain Rate Compression of Laminate Al-Graphene Composite and Mechanical Property Characterization

Owing to the opaque nature of the laminated structures, traditional high-speed optical camera cannot be used to detect the dynamic process of sub-surface deformation. In this article, we report a study of using high speed X-ray imaging to study the high strain rate deformation in laminated Al structures. We used a Kolsky bar apparatus to apply dynamic compression and a high-speed synchrotron X-ray phase contrast imaging (PCI) setup to conduct the in situ X-ray imaging study. The in situ X-ray imaging captures the shock wave propagation in the laminated structures. After shock compression, we characterized the microstructures by using transmission electron microscopy (TEM), which demonstrates an increase of dislocation density. In conclusion, the micro-pillar compression tests show that the yield strength at 0.2% offset of laminated Al-graphene composite has a significant increase of 67%, from 30 to 50 MPa, compared to laminate Al after shock loading.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Dislocation-induced stop-and-go kinetics of interfacial transformations

Most engineering materials are based on multiphase microstructures produced either through the control of phase equilibria or by the fabrication of different materials as in thin-film processing. In both processes, the microstructure relaxes towards equilibrium by mismatch dislocations (or geometric misfit dislocations) across the heterophase interfaces (1-5) . Despite their ubiquitous presence, directly probing the dynamic action of mismatch dislocations has been unachievable owing to their buried nature. In this work, using the interfacial transformation of copper oxide to copper as an example, we demonstrate the role of mismatch dislocations in modulating oxide-to-metal interfacial transformations in an intermittent manner, by which the lateral flow of interfacial ledges is pinned at the core of mismatch dislocations until the dislocation climbs to the new oxide/metal interface location. Together with atomistic calculations, we identify that the pinning effect is associated with the non-local transport of metal atoms to fill vacancies at the dislocation core. These results provide mechanistic insight into solid-solid interfacial transformations and have substantial implications for utilizing structural defects at buried interfaces to modulate mass transport and transformation kinetics.

25 ENERGY STORAGE↗
NASA NTRS1990

InAs/Ga(1-x)In(x)Sb superlattices for infrared detector applications

The successful growth of InAs/Ga(1-x)In(x)Sb superlattices and their optical and structural characterization is discussed. Samples were grown by molecular beam epitaxy at fairly low substrate temperatures (less than 400 C). Structural quality was assessed by reflection high energy electron difrraction, transmission electron microscopy, and x ray diffraction. Excellent structures were achieved for growth on thick, strain relaxed GaSb buffer layers on GaAs substrates, despite a residual threading dislocation density of 10(exp 9)cm(exp -2) originating at the GaSb/GaAs interface. Despite a lattice mismatch of 1.7 percent, InAs/Ga(0.75)In(0.25)Sb superlattices are observed to be free of misfit dislocations at the thicknesses examined here, owing to the close lattice match between the superlattice and GaSb, which evenly distributes compressive and tensile stresses between the InAs and Ga(0.75)In(0.25)Sb layers. Photoluminescence and photoconductivity measurements indicate that the energy gaps of the strain-layer superlattices are smaller than those of InAs/GaSb superlattices with the same layer thicknesses, and are in agreement with the theoretical predictions of Smith and Mailhiot. Energy gaps of 80 to 250 meV (15 to 5 microns) have been measured for InAs/Ga(0.75)In(0.25)Sb superlattices with 45 to 25 A/25 A layer thickness. Results demonstrate that far-infrared cutoff wavelengths are compatible with the thin superlattice layers required for strong optical absorption in type-II superlattices.

Miles, Richard H.↗
NASA NTRS1991

High resolution electrolyte for thinning InP by anodic dissolution and its applications to EC-V profiling, defect revealing and surface passivation

An extensive experimental study was conducted using various electrolytes in an effort to find an appropriate electrolyte for anodic dissolution of InP. From the analysis of electrochemical characteristics in the dark and under different illumination levels, x ray photoelectron spectroscopy and SEM/Nomarski inspection of the surfaces, it was determined that the anodic dissolution of InP front surface layers by FAP electrolyte is a very good choice for rendering smooth surfaces, free of oxides and contaminants and with good electrical characteristics. The FAP electrolyte, based on HF, CH3COOH, and H2O2 appears to be inherently superior to previously reported electrolytes for performing accurate EC-V profiling of InP at current densities of up to 0.3 mA/sq cm. It can also be used for accurate electrochemical revealing of either precipitates or dislocation density with application to EPD mapping as a function of depth, and for defect revealing of multilayer InP structures at any depth and/or at the interfaces.

Faur, Maria↗
DOE OSTI2020

Effect of grain structure and strain rate on dynamic recrystallization and deformation behavior: A phase field-crystal plasticity model

Herein, a phase field (PF)-crystal plasticity (CP) model has been developed to study the effects of initial grain structures, recrystallized grain orientation, and strain rates on dynamic recrystallization and deformation behavior under stress states typical of the Shear Assisted Processing and Extrusion (ShAPE) process. The model takes the geometrically necessary dislocation density as the nucleation criterion for recrystallization and minimizes the deformation energy as the driving force of recrystallized grain growth. Using this model, the effects of grain orientations and strain rates on dynamic recrystallization and deformation behavior were simulated. The results demonstrate that (1) a polycrystalline structure with the texture observed in ShAPE process has the lowest yield stress under the ShAPE stress conditions, (2) the recrystallized grains with the texture observed in ShAPE process largely soften the materials, and (3) higher shear strain rate or rotation speed results in larger magnitude of material softening.

36 MATERIALS SCIENCE↗
NASA NTRSDate not supplied

TPSAS-NF1676L-13792-DND

Extreme structural requirements of future aerospace vehicles motivate the development of new, ultra-durable materials and game-changing methodologies for material certification and sustainment. Computational simulations spanning many orders of magnitude in length and time scales—from the nanoscale of underlying damage processes to the larger scales of continuum cracks—are being developed to support these requirements. Results of these simulations are used to deduce key aspects of material response to loads and environments, including: - The microstructural mechanics that govern metal fatigue crack initiation and growth - The variety and complexity of the dislocation-precipitate interac- tions that underpin plastic behavior and damage evolution - The energetic principles that govern the interaction of water with crack surfaces within a structural component - The mechanics of grain boundary separation Modeling the physics behind these metal fatigue behaviors is extremely complex, and requires intensive, high-fidelity simulations. The knowledge gained through these simulations, however, is forming the keystone for advanced material design and will enable development of more capable, reliable structures for aerospace vehicles.

Jacob Hochhalter↗
DOE OSTI2021

Tailoring plasticity mechanisms in compositionally graded hierarchical steels fabricated using additive manufacturing

Abstract While there exists in nature abundant examples of materials with site-specific gradients in microstructures and properties, engineers and designers have traditionally used monolithic materials with discrete properties. Now, however, additive manufacturing (AM) offers the possibility of creating structures that mimic some aspects of nature. One example that has attracted attention in the recent years is the hierarchical structure in bamboo. The hierarchical architecture in bamboo is characterized by spatial gradients in properties and microstructures and is well suited to accommodate and survive complex stress states, severe mechanical forces, and large deformations. While AM has been used routinely to fabricate functionally graded materials, this study distinguishes itself by leveraging AM and physical metallurgy concepts to trigger cascading deformation in a single sample. Specifically, we have been successful in using AM to fabricate steel with unique spatial hierarchies in structure and property to emulate the structure and deformation mechanisms in natural materials. This study shows an improvement in the strength and ductility of the nature-inspired “hierarchical steel” compared with conventional cast stainless steels. In situ characterization proves that this improvement is due to the sequential activation of multiple deformation mechanisms namely twinning, transformation-induced plasticity, and dislocation-based plasticity. While significantly higher strengths can be achieved by refining the chemical and processing technique, this study sets the stage to achieve the paradigm of using AM to fabricate structures which emulate the flexibility in mechanical properties of natural materials and are able to adapt to in-service conditions.

36 MATERIALS SCIENCE↗
NASA NTRS1984

Brittleness of ceramics

The main characteristics of mechanical properties of ceramics are summarized and the causes of their brittleness, especially the limited mobility of dislocations, are discussed. The possibility of improving the fracture toughness of ceramics and the basic research needs relating to technology, structure and mechanical properties of ceramics are stressed in connection with their possible applications in engineering at high temperature.

Kroupa, F.↗
DOE OSTI2022

Investigation of crossed-twin structure formation in magnesium and magnesium alloys

In this work, the effect of alloying addition on the propensity for twin-twin interactions to transform into crossed-twin structures in magnesium alloys is investigated. A full-field elasto-viscoplastic fast Fourier transform (EVP-FFT) framework combined with a discrete twin model and dislocation density-based hardening law for slip strengths is used to calculate the micromechanical fields in the crystalline matrix around the interacting twins. AZ31 and MgLi alloys are selected along with pure Mg to study the influence of plastic anisotropy in connection with alloying elements. These alloys were selected since their plastic anisotropy measure, which is defined as the ratio between the critical resolved shear stress for pyramidal $\langle$c +a$\rangle$ and basal $\langle$a$\rangle$ slip modes, spanned a wide range. To quantify the role of twin thicknesses, we probe a range of impinging twin thicknesses while fixing the recipient twin thickness. The analysis reveals that: (i) the local driving stress for crossed twin structure formation generated from the interaction of the two twins is lower in a low plastically anisotropic material, like a MgLi alloy, than a high plastically anisotropic material like pure Mg and (ii) the critical impinging twin thickness needed to form the crossed twin structure in pure Mg, AZ31 and MgLi alloys is ~0.5, ~0.75 and ~1.5 times the recipient twin thickness. We propose a relationship between the tendency for crossed twin structure formation and the experimentally observed higher ductility in MgLi alloys compared to pure Mg. Finally, one key implication of the findings is that crossed- twin structure formation can be hindered and the ductility of magnesium alloy thereby improved by properly choosing alloying elements that lower the slip strength for pyramidal $\langle$c + a$\rangle$ slip.

36 MATERIALS SCIENCE↗
NASA NTRS1982

The structure of 110 tilt boundaries in large area solar silicon

The models of Hornstra and their connection to the repeating group description of grain boundaries (7-10) are discussed. A model for the Sigma = 27 boundary containing a zig-zag arrangement of dislocations is constructed and it is shown that zig-zag models can account for the contrast features observed in high resolution transmission electron micrographs of second and third order twin boundaries in silicon. The boundaries discussed are symmetric with a 110 tilt axis and a (110) boundary plane in the median lattice (the median plane). The median lattice is identical in structure and halfway in orientation between the crystal lattices either side of the boundary.

Ast, D. G.↗
DOE OSTI2025

Modification of Ni-20Cr corrosion dealloying behavior in molten fluorides via cold work induced plastic deformation

The corrosion dealloying behavior of cold-worked (CW) Ni20Cr alloy (wt%) was studied in molten LiF-NaF-KF (or FLiNaK) salts at 600 °C, equal to a homologous temperature (TH) of 0.52. Alloys were cold-rolled to achieve reductions of thickness of 10%, 30%, and 50% introducing plastic deformation and a high density of dislocations. Potentiostatic holds (Eapplied) were applied in two different electrode potential regimes. At 1.75VK+/K$${\text{V}}_{{\text{K}}^{+}/{\text{K}}}$$, Cr dealloying to Cr(II) and Cr(III) is predominant, while at 1.90 VK+/K$${\text{V}}_{{\text{K}}^{+}/{\text{K}}}$$, both Ni and Cr are oxidized in molten FLiNaK at 600 °C. In these potential regimes, dealloyed Ni20Cr displayed bicontinuous porosity within the grain interior and at grain boundaries, driven by the high driving force for Cr dissolution and sustained by defect mediated outward solid state diffusion of Cr in parallel with surface diffusion of Ni. The bicontinuous porous structure developed was observed to undergo further coarsening and densification of the Ni-rich ligaments at a higher electrode potential. The main effect of CW observed is the introduction of plastic deformation and dislocation substructures that serve as short-circuit paths for Cr solid state diffusion to surfaces exposed to FLiNaK. This modified the evolution of the bicontinuous porous structure which increased with CW substantially. Kinetic analysis reveals that the Cr dealloying at +1.75 VK+/K$${\text{V}}_{{\text{K}}^{+}/{\text{K}}}$$ and 1.90 VK+/K$${\text{V}}_{{\text{K}}^{+}/{\text{K}}}$$ is initially charge transfer controlled, except for the 50% CW condition at 1.90 VK+/K$${\text{V}}_{{\text{K}}^{+}/{\text{K}}}$$, where the process becomes limited by slow Cr defect mediated bulk diffusion. The rate determining factors are explored and compared to experimental results.

Chan, Ho Lun↗
DOE OSTI2020

Hardening in Au-Ag nanoboxes from stacking fault-dislocation interactions

Porous, nano-architected metals with dimensions down to ~10 nm are predicted to have extraordinarily high strength and stiffness per weight, but have been challenging to fabricate and test experimentally. Here, we use colloidal synthesis to make ~140 nm length and ~15 nm wall thickness hollow Au-Ag nanoboxes with smooth and rough surfaces. In situ scanning electron microscope and transmission electron microscope testing of the smooth and rough nanoboxes show them to yield at 130 ± 45 MPa and 96 ± 31 MPa respectively, with significant strain hardening. A higher strain hardening rate is seen in rough nanoboxes than smooth nanoboxes. Finite element modeling is used to show that the structure of the nanoboxes is not responsible for the hardening behavior suggesting that material mechanisms are the source of observed hardening. Molecular dynamics simulations indicate that hardening is a result of interactions between dislocations and the associated increase in dislocation density.

42 ENGINEERING↗
DOE OSTI2024

Development of a MOOSE-based crystal plasticity model with irradiation defect evolution for irradiation creep in 316

Irradiation creep and irradiation swelling are two of the lifetime limiting factors for structural materials in nuclear reactors. These mechanical effects are driven by irradiation defect evolution and the interaction of those defects with dislocations in the microstructure. We present here a coupled cluster dynamics – crystal plasticity approach to model irradiation swelling and creep behavior in 316 SS. The time-dependent evolution of irradiation defects is calculated with a cluster dynamics approach and passed to the crystal plasticity model to compute the dislocation evolution. We show the impact of the irradiation defect evolution on the stress state in the material, which drives inelastic deformation through dislocation motion. The inelastic deformation in the 316 SS is dependent on the dose rate, where the inelastic deformation driven by the early-stage irradiation defect evolution determines the mechanical behavior of the 316 SS.

316 Stainless Steels↗
DOE OSTI2025

Creep Property of Intermetallic Dispersive Steels for Nuclear Applications

To meet the materials performance demands of next-generation nuclear and high-temperature energy systems, a new class of intermetallic-dispersive steels (IDS) has been designed through integrated computational thermodynamics and alloy design strategies. The IDS alloys incorporate coherent L1₂ (γ′-Ni₃Al) nanoprecipitates within an Fe–Ni–Cr austenitic matrix, engineered to achieve both high temperature strength and thermodynamic stability while suppressing the formation of detrimental δ-Ni₃Nb and η-Ni₃Ti phases. Initial creep testing of Ti-IDS and TiTa-IDS alloys demonstrates rupture lives comparable to or exceeding those of Inconel 718 and ODS steels, despite being fabricated through conventional ingot metallurgy. Step-load creep tests identified a stress threshold near 300–350 MPa for the onset of tertiary creep, and in-situ neutron diffraction experiments on Ti-IDS revealed clear load partitioning between the matrix and γ′ precipitates: elastic strain is shared by both phases, while plastic strain localizes in the matrix. These results confirm that stable γ′–matrix interfaces play a dominant role in retarding dislocation motion and enhancing creep resistance. In FY26, the program will conduct repeat creep rupture testing of TiTa-IDS at 650 °C/400 MPa, initiate long-term rupture testing of TiNb-IDS, and perform TEM-based microstructural characterization to elucidate dislocation–precipitate interactions and microstructural stability. Collectively, these efforts will establish the mechanistic foundation for next-generation high-temperature structural materials based on the IDS concept.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗