SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Investigation was made to optimize selection of insulation materials for reusable space vehicles which will be repeatedly operated over periods of up to ten years. Results of study are summarized in two reports. Volume I describes tests and significant findings. In Volume II, extensive test data obtained are organized in handbook form.
Ten materials were evaluated for mechanical and dielectric properties following long term vacuum exposure. Data obtained for these materials is presented in tabular form.
The effects of prolonged spacecraft materials were determined and the results compared with predicted behavior. The adhesion and dielectric properties of poly-thermaleze and therm-amid magnet wire insulation were studied. The tensile properties of Lexan, polyurethane, polyethelyne, lucite, and nylon were studied well as the flexure and tensile characteristic of Adlock 851, a phenolic laminate. The volume resistivity of Cho-seal, a conductive elastomer was also a examined. Tables show the time exposed at thermal vacuum, and the high, low, and average MPA and KSI.
Information on materials and structures for use in space is given in viewgraph form. Information is given on the Materials and Structures Division of NASA's Office of Aeronautics and Space Technology. The Division's space research and development budget is given. Further information is given on space materials and structures, space environmental effects, radiation effects, high temperature materials research, metal matrix composites, SiC fiber reinforced titanium alloys, structural dynamics, and control of flexible structures.
Two assemblies of laboratory equipment developed for use in testing abilities of polymers, paints, and other materials to withstand ultraviolet radiation and charged particles. One is vacuum ultraviolet source built around commercial deuterium lamp. Other exposes specimen in partial vacuum to both ultraviolet radiation and brush corona discharge. Either or both assemblies used separately or together to simulate approximately combination of solar radiation and charged particles encountered by materials aboard spacecraft in orbit around Earth. Also used to provide rigorous environmental tests of materials exposed to artificial ultraviolet radiation and charged particles in industrial and scientific settings or to natural ultraviolet radiation and charged particles aboard aircraft at high altitudes.
This report focuses on the development of an operational Rutherford backscattering spectrometry (RBS) system and shows the application of such a system on a space environmental test. Thin films of aluminum and tantalum were deposited on diamond substrates. These films were anodized and preexposure characterization spectra obtained using RBS and total hemispherical reflectance. The samples were exposed to energetic protons then postexposure characterization spectra was obtained using the same techniques. Conclusions based on the comparison of preexposure and postexposure spectra are presented. RBS comparison spectra show no change in the metal/metal oxide interface, while the comparison reflectance data indicate change. Explanations for this reflectance change are presented in this report.
A methodology for enhanced heat transport and storage that uses a new two-component fluid mixture consisting of a microencapsulated phase change material (microPCM) for enhanced latent heat transport is outlined. SBIR investigations for NASA, USAF, SDIO, and NSF since 1983 have demonstrated the ability of the two-component microPCM coolants to provide enhancements in heat transport up to 40 times over that of the carrier fluid alone, enhancements of 50 to 100 percent in the heat transfer coefficient, practically isothermal operation when the coolant flow is circulated in an optimal manner, and significant reductions in pump work.
In the design of new aerospace materials, developmental testing is conducted to characterize the behavior of the material under severe environmental conditions of high stress, temperature, and vibration. But to test these materials under extreme conditions requires sensors that can perform in harsh environments. Current sensors can only monitor high temperature test samples using long throw instrumentation, but this is inherently less accurate than a surface mounted sensor, and provides no means for fabrication process monitoring. A promising alternative is the use of sapphire optical fiber sensors. Sapphire is an incredibly rugged material, being extremely hard (9 mhos), chemically inert, and having a melting temperature (over 2000 C). Additionally, there is a extensive background of optical fiber sensors upon which to draw for sapphire sensor configurations.
PM304 is a NASA-developed composite powder metallurgy material that is being developed for high temperature applications such as bushings in high temperature industrial furnace conveyor systems. My goal this summer was to analyze and evaluate the effects that heat exposure had on the PM304 material at 500 C and 650 C. The material is composed of Ni-Cr, Ag, Cr2O3, and eutectic BaF2-CaF2. PM304 is designed to eliminate the need for oil based lubricants in high temperature applications, while reducing friction and wear. However, further investigation was needed to thoroughly examine the properties of PM304. The effects of heat exposure on PM304 bushings were investigated. This investigation was necessary due to the high temperatures that the material would be exposed to in a typical application. Each bushing was cut into eight sections. The specimens were heated to 500 C or 650 C for time intervals from 1 hr to 5,000 hrs. Control specimens were kept at room temperature. Weight and thickness measurements were taken before and after the bushing sections were exposed to heat. Then the heat treated specimens were mounted and polished side by side with the control specimens. This enabled optical examination of the material's microstructure using a metallograph. The specimens were also examined with a scanning electron microscope (SEM). The microstructures were compared to observe the effects of the heat exposure. Chemical analysis was done to investigate the interactions between Ni-Cr and BaF2-CaF2 and between Cr2O3 and BaF2-CaF2 at high temperature. To observe this, the two compounds that were being analyzed were mixed in a crucible in varied weight percentages and heated to 1100 C in a furnace for approximately two hours. Then the product was allowed to cool and was then analyzed by X-ray diffraction. Interpretation of the results is in progress.
A process of waterproofing alumina-rich or silica-rich fibrous thermal insulation material, the process including the steps of: (a) providing an alumina-rich or a silica-rich fibrous material; (b) providing a waterproofing solution including: (1) a carrier solvent selected from the group consisting of aliphatic alcohols having from 1C to 6C, water, and mixtures thereof; and (2) an alkoxysilane defined by the formula R.sub.4-x -Si-(O-R').sub.x where x is 1-3 and R is selected from the group consisting of alkyl groups having from 1C to 10C, hydrogen, or fluorocarbon groups having from 1F to 15F; and where O-R' is an alkoxy group having from 1C to 5C, or a mixture of alkoxysilanes defined by the above formula R.sub.4-x -Si-(O-R').sub.x ; and optionally (3) modifiers including acids, such as acetic acid or nitric acid, or bases, such as ammonium hydroxide, RNH.sub.2, R.sub.2 NH, or R.sub.3 N, or MOH, where R is selected from the group consisting of alkyl groups having from 1C to 10C or hydrogen, and where M=Na, Li, or K; (c) contacting the fibrous material with the waterproofing solution for a sufficient amount of time to waterproof the fibrous material; and (d) curing the coated fibrous material to render it sufficiently waterproof. A chemical solution for waterproofing alumina-rich or silica-rich fibrous thermal insulation materials, the solution including: (a) a carrier solvent selected from the group consisting of aliphatic alcohols having from 1C to 6C, water, and mixtures thereof; and (b) an alkoxysilane defined by the formula R.sub.4-x -Si-(O-R').sub.x where x is 1-3 and R is selected from the group consisting of alkyl groups having from 1C to 10C, hydrogen, or fluorocarbon groups having from 1F to 15F; and where O-R' is an alkoxy group having from 1C to 5C, or a mixture of alkoxysilanes defined by the above formula R.sub.4-x -Si-(O-R').sub.x ; and optionally (c) modifiers including acids, such as acetic acid or nitric acid, or bases, such as ammonium hydroxide, RNH.sub.2, R.sub.2 NH, or R.sub.3 N, or MOH, where R is selected from the group consisting of alkyl groups having from 1C to 10C or hydrogen, and where M=Na, Li, or K.
In support of the design of wind turbine generator airfoils/blades utilizing Douglas Fir/West System Epoxy laminated composite material, a program was undertaken to define pertinent material properties utilizing small scale test specimens. Task 1 was the development of suitable monotonic tension, compression, short beam shear and full reversed cyclic specimen designs and the companion grips and testing procedures. Task 2 was the generation of the material properties at two environmental conditions utilizing the specimens and procedures developed in Task 1. The monotonic specimens and procedures generated results which compare favorably with other investigators while the cyclic results appear somewhat conservative. Adding moisture and heat or scarf joints degraded the monotonic performance but had a more nebulus effect with cyclic loading.
Ytterbium disilicate (Yb2Si2O7) is a state-of-the-art topcoat material used in environmental barrier coatings (EBCs) to protect SiC-SiC composites from water vapor corrosion in gas turbine engines. However, it’s degradation by thermochemical and thermomechanical particle interactions may limit its use in next generation engine systems. Several static furnace tests have been performed on Yb2Si2O7 to elucidate methods of degradation, although dynamic testing in an engine-relevant environment has not been carried out. Ultimately, testing and evaluation of materials that incorporates all environmental damage modes will allow for an accurate assessment of long-term durability and operating lifetime. This work details the investigation of particle-induced erosion and corrosion of Yb2Si2O7 in NASA Glenn’s Erosion Burner Rig Facility. Coating durability was investigated as a function of test temperature, particle size, and deposition rate. Thermal cycling was also incorporated into testing to determine the interplay of heating/cooling cycles with particle degradation. Overall, these analyses will be used to determine coating robustness in an engine relevant environment.
Ytterbium disilicate (Yb2Si2O7) is a state-of-the-art topcoat material used in environmental barrier coatings (EBCs) to protect SiC-SiC composites from water vapor corrosion in gas turbine engines. However, it’s degradation by thermochemical and thermomechanical particle interactions may limit its use in next generation engine systems. Several static furnace tests have been performed on Yb2Si2O7 to elucidate methods of degradation, although dynamic testing in an engine-relevant environment has not been carried out. Ultimately, testing and evaluation of materials that incorporates all environmental damage modes will allow for an accurate assessment of long-term durability and operating lifetime. This work details the investigation of particle-induced erosion and corrosion of Yb2Si2O7 in NASA Glenn’s Erosion Burner Rig Facility. Coating durability was investigated as a function of test temperature, particle size, and deposition rate. Thermal cycling was also incorporated into testing to determine the interplay of heating/cooling cycles with particle degradation. Overall, these analyses will be used to determine coating robustness in an engine relevant environment.
The flight and retrieval of the National Aeronautics and Space Administration's Long Duration Exposure Facility (LDEF) provided an opportunity for the study of the low-Earth orbit (LEO) environment and long-duration space environmental effects (SEE) on materials that is unparalleled in the history of the U.S. Space Program. The remarkable flight attitude stability of LDEF enables specific analyses of various individual and combined effects of LEO environmental parameters on identical materials on the same space vehicle. This paper provides an overview of the interim LDEF materials findings of the Principal Investigators and the Materials Special Investigation Group. In general, the LDEF data is remarkably consistent; LDEF will provide a 'benchmark' for materials design data bases for satellites in low-Earth orbit. Some materials were identified to be encouragingly resistant to LEO SEE for 5.8 years; other 'space qualified' materials displayed significant environmental degradation. Molecular contamination was widespread; LDEF offers an unprecedented opportunity to provide a unified perspective of unmanned LEO spacecraft contamination mechanisms. New material development requirements for long-term LEO missions have been identified and current ground simulation testing methods/data for new, durable materials concepts can be validated with LDEF results. LDEF findings are already being integrated into the design of Space Station Freedom.
We present a supervised machine learning (ML) framework to automatically identify new particle formation (NPF) events and analyze key atmospheric factors associated with their occurrence and growth. We applied ML to detect NPF events using start time and particle concentrations across size ranges, while identifying atmospheric variables including ambient temperature, relative humidity, solar radiation intensity (SRI), wind speed, wind direction, boundary layer height, total organics, sulfate, nitrate, total surface area concentration, sulfur dioxide, and turbulent kinetic energy (TKE). We analyzed a 6-year data set from the Atmospheric Radiation Measurement at the Southern Great Plains (SGP) site in Oklahoma, USA. Using long-term ground-based measurements, we identified NPF events and applied Random Forest Classifiers, which achieved 90%–95% prediction accuracy. Feature importance analysis highlighted SRI, relative humidity, and ambient temperature as the most influential variables, contributing normalized importances of 28%, 17%, and 10%. Partial Dependence Plots (PDPs) indicated that higher SRI and lower relative humidity were critical in promoting NPF formation at SGP. Seasonally, NPF events were more frequent in winter (42.1%) and spring (35.5%), and least in summer (4.0%). Particle growth rates also exhibited a seasonal variation, with the lowest in winter (below 2 nm hr −1 ) and highest in late spring and early summer (exceeding 5 nm hr −1 ). Temperature, turbulent kinetic energy, and aerosol properties were the primary factors of growth rate variability. This study advances predictive modeling of NPF, offers insights for future campaign deployments, and demonstrates the effectiveness of ML in understanding the formation and growth of atmospheric aerosols.
Alkaline cleaners used to process aluminum substrates have contained chromium as the corrosion inhibitor. Chromium is a hazardous substance whose use and control are described by environmental laws. Replacement materials that have the characteristics of chromated alkaline cleaners need to be found that address both the cleaning requirements and environmental impacts. This report will review environmentally friendly candidates evaluated as non-chromium alkaline cleaner replacements and methods used to compare those candidates one versus another. The report will also list characteristics used to select candidates based on their declared contents. It will also describe and evaluate methods used to discriminate among the large number of prospective candidates.
These proceedings describe the application of LDEF data to spacecraft and payload design, and emphasize where space environmental effects on materials research and development is needed as defined by LDEF data. The LDEF six years of exposure of materials has proven to be by far the most comprehensive source of information ever obtained on the long-term performance of materials in the space environment. The conference provided a forum for materials scientists and engineers to review and critically assess the LDEF results from the standpoint of their relevance, significance, and impact on spacecraft design practice. The impact of the LDEF findings on materials selection and qualification, and the needs and plans for further study, were addressed from several perspectives. Many timely and needed changes and modifications in external spacecraft materials selection have occurred as a result of LDEF investigations.
Aeronautics research at NASA Glenn Research Center includes development, characterization and modeling of high temperature, lightweight materials and fabrication processes for aircraft propulsion systems with increased efficiency and reduced emissions, fuel burn and noise. Current propulsion materials research includes Ceramic Matrix Composites and Environmental Barrier Coatings, Polymer Matrix Composites and Additive Manufacturing processes. This presentation will summarize recent progress and plans in these areas.