Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Barrier materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Integrated TBC/EBC for SiC Fiber Reinforced SiC Matrix Composites for Next Generation Gas Turbines (Final Report)

In this ambitious project, a significant challenge preventing widespread use of ceramic matrix composites in hot section components of gas power generating turbines was addressed. Hot section components made from SiC fiber reinforced SiC matrix composites (SiC/SiC composites), have the potential to achieve a combined cycle energy efficiency of above 65%. To achieve this efficiency, the temperature of the combustion gases on the turbine component surface is expected to reach as high as ~1700ºC (3100ºF). However, SiC/SiC composites suffer from volatilization at high temperature under high velocity steam environment – typical in a turbine hot chamber. This integrated collaborative project, between two research groups at Clemson University and a team of engineers and scientists at GE Gas Power, focused on design, fabrication and evaluation of a new graded environmental barrier coating. Using the excellent compositional tailorability of polymer derived ceramics (PDCs), we developed an integrated EBC/BC that smoothly transitions from bottom SiC/SiC bond interface to hermetic sesquioxide (Y 2 O 3 ) top surface. This smooth compositional transition avoided the sharp CTE mismatch at interfaces to greatly reduce the thermal stress. The developed EBC is compatible with and bonds well with the bond coat that GE uses. The top hermetic oxide surface ensures low oxygen transportation and volatilization rates under the high velocity steam environment. The graded microstructure with increasing sesquioxide concentration also decreases the amount of Si and C elements near the top hermetic sesquioxide layer. Coatings made using a process suitable for manufacturing – atmospheric plasma spraying was demonstrated. The microstructure of coatings made using this process were fully characterized. Finally, the performance of these coatings was investigated under the most demanding conditions for this application. Specifically, high temperature, high velocity steam exposure; thermal shock test; and thermal cycling tests. The graded coatings performed exceptionally well in all these tests. Specific suggestions for future development in this area have also been identified. In addition to the excellent technical progress, this project helped initiate a robust collaboration between the research groups at Clemson and GE Gas Power. It also provided a high-quality learning and mentoring opportunity for the three post-doctoral research associates and two UG students at Clemson University who worked on this project. All proposed tasks, sub-tasks were completed, and all milestones achieved.

03 NATURAL GAS↗
DOE OSTI2022

Tunneling full-wave infrared rectenna

A rectenna is used for full-wave rectification of infrared radiation to produce electricity. In the rectenna, a metallic grating overlies a semiconductor body. A tunnel barrier is interposed between each grating element and the semiconductor body. Each of the grating elements overlies a bridge pair consisting of a region of n+-doped semiconductor and a region of p+-doped semiconductor, both of which are embedded in more lightly doped host semiconductor material. Each of the two regions that compose the bridge pair forms a rectifying tunnel junction through a tunnel barrier to at least one overlying grating element. Each of the two regions also forms a semiconductor junction with the host semiconductor material.

Davids, Paul↗
DOE OSTI2020

2D Electrets of Ultrathin MoO 2 with Apparent Piezoelectricity

Since graphene, a variety of 2D materials have been fabricated in a quest for a tantalizing combination of properties and desired physiochemical behavior. 2D materials that are piezoelectric, i.e., that allow for a facile conversion of electrical energy into mechanical and vice versa, offer applications for sensors, actuators, energy harvesting, stretchable and flexible electronics, and energy storage, among others. Unfortunately, materials must satisfy stringent symmetry requirements to be classified as piezoelectric. Here, 2D ultrathin single-crystal molybdenum oxide (MoO 2 ) flakes that exhibit unexpected piezoelectric-like response are fabricated, as MoO 2 is centrosymmetric and should not exhibit intrinsic piezoelectricity. However, it is demonstrated that the apparent piezoelectricity in 2D MoO 2 emerges from an electret-like behavior induced by the trapping and stabilization of charges around defects in the material. Arguably, the material represents the first 2D electret material and suggests a route to artificially engineer piezoelectricity in 2D crystals. Specifically, it is found that the maximum out-of-plane piezoresponse is 0.56 pm V -1 , which is as strong as that observed in conventional 2D piezoelectric materials. The charges are found to be highly stable at room temperature with a trapping energy barrier of ≈2 eV.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Minimized aging of isocyanurate-based rigid cellular foams for buildings through tailored barrier facers and optimized formulation

The thermal resistivity (h·ft 2 ·°F/Btu/in.) of closed-cell rigid foam insulation materials significantly decreases over time. Diffusion-tight facers are designed to significantly enhance initial thermal resistivity and long-term thermal performance by preventing gas diffusion into the foam cells and inhibiting the escape of low thermal conductivity blowing agents. In addition to the gas diffusion property of the facer film, adhesion between the foam and the facer is crucial for achieving diffusion-tight bonding. Here, this study addresses the challenge of thermal aging by investigating how facer film properties and foam formulation influence the durability of thermal performance. A systematic evaluation was conducted to understand the effects of polymeric barrier films, surface treatments, facer coverage, and foam matrix rigidity on thermal resistivity over time. Key findings reveal that diffusion-tight facers, particularly those with metallized layers and compatible heat seal layers, significantly reduce gas exchange and improve foam-facer adhesion. The optimized system, incorporating barrier facers and a tailored polyisocyanurate foam formulation, achieved initial and aged thermal resistivity values after 200 days of approximately 8.3 and 7.4 h ft 2 ·°F/Btu/in., respectively representing only a 10 % reduction compared to a 17 % reduction observed in control samples without facers. Notably, polyurethane spray foams with facers exhibited only a 4 % reduction in thermal resistivity, compared to a 23 % decrease in control samples, demonstrating nearly six times better retention of thermal performance. This innovative facer technology presents a promising solution for reducing energy costs and represents a significant advancement in optimizing energy management for building envelopes in future technologies. This technology can also be adapted for other applications that necessitate the preservation of long-term thermal performance.

Wanasinghe, Shiwanka Vidarshi [Oak Ridge National ↗
DOE OSTI2020

Phase Change-Driven Negative Activation Energies in Pd/Carbon-Based/Organic Getter Hydrogenation Reactions

In this study, the hydrogenation of 1,4-diphenylbutadiyne (DPB) blended with carbon-supported Pd (DPB–Pd/C) in the form of pellets was investigated by isothermal–isobaric experiments at 1333 Pa of H 2 and in the temperature range of 291–315 K. The extracted kinetics were then used in conjunction with a complementary constant rate of H 2 input experimentation to model the performance of a DPB-catalysis/support system as a function of temperature and H 2 partial pressure. First-principles density functional theory (DFT) calculations were also performed to shed light on the molecular level energetics of DPB and its intermediate states. A seemingly puzzling formation of alternate positive activation energy barrier (higher reaction rate with higher temperature) and negative activation energy barrier (higher reaction rate with lower temperature) zones during the hydrogenation process was discovered. However, this observed phenomenon can be logically explained in terms of the associated phase changes and H 2 transport in the material. This work provides a good illustration of a rarely encountered chemical process with a negative activation energy barrier.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

CFD/FEA Co-Simulation Framework for Analysis of the Thermal Barrier Coating Design and Its Impact on the HD Diesel Engine Performance

Thermal barrier coatings (TBCs) have been investigated both experimentally and through simulation for mixing controlled combustion (MCC) concepts as a method for reducing heat transfer losses and increasing cycle efficiency, but it is still a very active research area. Early studies were inconclusive, with different groups discovering obstacles to realizing the theoretical potential. Nuanced papers have shown that coating material properties, thickness, microstructure, and surface morphology/roughness all can impact the efficacy of the thermal barrier coating and must be accounted for. Adding to the complexities, a strong spatial and temporal heat flux inhomogeneity exists for mixing controlled combustion (diesel) imposed onto the surfaces from the impinging flame jets. In support of the United States Department of Energy SuperTruck II program goal to achieve 55% brake thermal efficiency on a heavy-duty diesel engines, this study sought to develop a deeper insight into the inhomogeneous heat flux from mixing controlled combustion on thermal barrier coatings and to infer concrete guidance for designing coatings. To that end, a co-simulation approach was developed that couples high-fidelity computational fluid dynamics (CFD) modeling of in-cylinder processes and combustion, and finite element analysis (FEA) modeling of the thermal barrier-coated and metal engine components to resolve spatial and temporal thermal boundary conditions. The models interface at the surface of the combustion chamber; FEA modeling predicts the spatially resolved surface temperature profile, while CFD develops insights into the effect of the thermal barrier coating on the combustion process and the boundary conditions on the gas side. The paper demonstrates the capability of the framework to estimate cycle impacts of the temperature swing at the surface, as well as identify critical locations on the piston/thermal barrier coating that exhibit the highest charge temperature and highest heat fluxes. In addition, the FEA results include predictions of thermal stresses, thus enabling insight into factors affecting coating durability. An example of the capability of the framework is provided to illustrate its use for investigating novel coatings and provide deeper insights to guide future coating design.

42 ENGINEERING↗
DOE OSTI2025

Contaminant Investigation and Pre‐Processing Opportunities for Textile‐To‐Textile Recycling

Millions of metric tons of textiles are landfilled or incinerated each year in the United States, with less than 1% of textiles recycled into new clothing or fabrics. To counter this trend, a growing number of companies and researchers are exploring how a circular economy can be applied to support textile‐to‐textile recycling. A significant barrier they face comes down to quickly and efficiently extracting pure feedstock material from post‐consumer garments that feature a mix of natural and synthetic fibers. Textile recyclers prefer pure feedstocks, as working with mixed sources typically means lower throughput, higher risk of equipment failure, and diminished business margins. To facilitate a circular economy for textiles, methods, and technologies are needed that can efficiently separate out materials and contaminants from end‐of‐life textiles to increase the flow of pure feedstocks to recyclers. This paper summarizes findings from interviews with a cross section of textile recyclers and from a review of literature to define basic feedstock requirements. In addition to our qualitative research, we deconstruct a bale of post‐consumer textiles and analyze them using computer‐vision imaging, Fourier transform infrared spectroscopy (FTIR), and machine learning. The resulting data are used to set system‐level design inputs for an automated contaminant removal system to process post‐consumer clothing into appropriate feedstocks for recycling. To set the system's levels for automated real‐time near‐infrared analysis, we identify the minimum percentage of primary material that any single garment in a load of used clothing must contain for the average of the full output stream to meet the target purity levels of recyclers. Here, the envisioned automated system can also address undesirable trace materials that might contaminate the processed stream by using imaging cameras coupled with artificial intelligence to identify sections of clothing for de‐trimming. Proof‐of‐concept machine learning algorithms are evaluated to locate and identify trims or garment areas with hidden contaminant materials. Integrating these methods into automated textile cutting systems can provide a cost‐effective means for increasing feedstock purity from used clothing, which can advance circularity for textiles by helping recyclers to reach production volumes and quality targets that were not possible solely with manual dismantling operations.

Parsons, Ryan [Rochester Institute of Technology, ↗
DOE OSTI2023

Understanding the Breakdown Behavior of Ultrawide-Bandgap Boron Nitride Power Diodes Using Device Modeling

Herein, a device study using technology computer-aided design simulation to theoretically analyze the electrical performance of ultrawide-bandgap boron nitride (BN)-based vertical junction devices is performed, including h-BN Schottky diode, h-BN pn diode, and h-BN/AlN pn diode; this is also the first demonstration of the BN power devices in simulation. The material properties of BN are defined with recently reported data, and the physical mechanisms of the device performance are systematically investigated. Additionally, the h-BN junctions in this simulation shows excellent performance, especially for breakdown behaviors. Schottky diode shows a turn-on voltage of 0.6 V for Pt Schottky contact and breakdown voltages over 450 V for 5 μm, 6 × 10 15 cm –3 p-type-doped drift layer; The h-BN pn diode shows a turn-on voltage of 6 V and breakdown voltages over 3 kV with a critical electric field of 13.6 MV cm –1 for 2.5 μm, 2 × 10 16 cm –3 p-type-doped drift layer. The h-BN/AlN heterojunction pn diode shows a turn-on voltage of 5.8 V and breakdown voltage over 2 kV for 2.5 μm, 2 × 10 16 cm –3 n-type-doped AlN drift layer. Herein, an understanding of the device principles of vertical BN junctions is provided, which can serve as a reference for the future development of robust BN power electronics.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Robust galactomannan/graphene oxide film with ultra-flexible, gas barrier and self-clean properties

Here, this study examines a facile technology to manufacture food packaging alternatives with superior mechanical, ultra-flexible, gas barrier and self-cleaning properties, based on green and benign starting materials. A novel galactomannan (GM) was isolated from the Sesbania cannabina seeds, which was used as a matrix for the fabrication of GM-based films. Inspired by the brick-and-mortar structure of natural nacre, a facile method was adopted to fabricate an artificial nacre based on the self-assembly of GM and borate crosslinked graphene oxide (GO). These GM/GO composites are ultra-flexible, which can be folded into various shapes. The tensile strength reached 135.54 MPa which is 2.40 times that of the pure GM film. In addition, after coating with the poly(dimethylsiloxane) (PDMS), these films became hydrophobic (WCA around 120°) with self-cleaning properties. Our study further revealed that the oxygen and water vapor permeabilities were improved with the introduction of GO and PDMS coating.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Temperature-Dependent Carrier Extraction and the Effects of Excitons on Emission and Photovoltaic Performance in Cs0.05FA0.79MA0.16Pb(I0.83Br0.17)3 Solar Cells

The photovoltaic parameters of triple cation perovskite [Cs0.05FA0.79MA0.16Pb(I0.83Br0.17)3] solar cells are investigated focusing on the electro-optical properties and differences in performance at low and high temperatures. The signature of a parasitic barrier to carrier extraction is observed at low temperatures, which results in a loss of performance at T < 200 K. Intensity-dependent measurements indicate extraction across this parasitic interface is limited by a combination of the exciton binding energy and thermionic emission. However, the photovoltaic performance of the device is recovered at low intensity - where the photocarrier generation rate threshold is lower than the thermionic extraction rate. Loss of solar cell performance is also observed to be strongly correlated to an increase in photoluminescence intensity, indicating inhibited carrier extraction results in strong radiative recombination and that these systems do not appear to be limited by significant thermally activated non-radiative processes. Evidence of limited carrier extraction due to excitonic effects is also observed with a strong anti-correlation in photoluminescence and carrier extraction observed at lower temperatures.

barrier↗
DOE OSTI2020

Surface diffusion manifestation in electrodeposition of metal anodes

Metal anode-based battery systems have been deemed indispensable towards energy storage renaissance engendering extensive research into strategies countering dendritic growth of metal electrodeposition. Fundamentally, the morphological evolution of a material is uniquely characterized by the heights of its self-diffusion barrier across multiple pathways. Herein, based on a coarse-grained kinetic Monte Carlo method, we derive insights into the nucleation and growth of metallic electrodeposits in liquid electrolytes, governed by surface self-diffusion characteristics cognizant of the diverse diffusion routes including terrace, away from step and interlayer pathways. We deconvolve the roles played by each of these surface diffusion mechanisms in conjunction with the electrochemical reaction rate on the deposition morphology regime (film vs. mossy vs. fractal). We identify interlayer diffusion as the predominant morphology-determining mechanism; dendrite-free deposition even at moderate current rates constrains this diffusion barrier to an upper limit. Additionally, we highlight subtle features amidst the realm of the morphological growth assortment that connect to the cell's electrochemical performance. Finally, we delineate morphological features of Li, Na, Mg and Al based on their respective surface diffusion barriers and applied overpotentials, and provide a baseline for the interpretation of experimental observations. This fundamental study sheds light on the mesoscale underpinnings of morphological variances in mono-valent and multi-valent metal electrodeposition.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Elucidating the formation mechanisms of zeolites using data-driven modelling and in-situ characterization

Zeolites are the main solid catalysts used by the chemical industry. The use of zeolites in separations and as shape selective catalysts requires control of the width and connectivity of their pores. 235 distinct zeolite frameworks have been synthesized to date, of over 2 million that have been proposed. Recent work indicates that the limitation is in large part kinetic: new synthetic pathways are required to access new zeolites. Organic cations are used to direct the synthesis towards specific zeolites. However, the molecular mechanisms by which cations direct the nucleation towards specific zeolites is not known. Elucidating these mechanisms is key to realize new zeolites for catalysis and separations, and is the focus of this project. This project developed and implemented a synergistic, data-driven computational and experimental approach to resolve the molecular pathways of nucleation, growth, and polymorph selection of zeolites and the role of organic cations in directing their formation. The project developed computationally efficient and accurate models for the study of the nucleation and growth of pure silica zeolites in molecular simulations, using machine learning with data from experiments. Simulations with these models were integrated with scanning tunneling electron microscopy, computer vision, and deep learning to unveil the molecular pathways of formation of a zeolite. Of particular interest in this project was to elucidate the role of amorphous precursors in the nucleation of the zeolite. Previous experiments indicate that zeolites are born within non-crystalline aggregates in which the silicates and organic cations have local and medium range order similar to that of the zeolite. The organic cations that direct the formation of zeolites and those that direct the formation of ordered mesoporous silicas are similar. We hypothesized that the frustrated attraction that for large organic cations leads to the formation of stable mesophases that direct the synthesis of mesoporous silicas, could promote the formation of metastable mesophases that can assist in the nucleation and polymorph selection of zeolites. The simulations resolved how structure directing agents build crystalline order and showed that mesoscopic pre-ordering occurs is not required to facilitate the nucleation of zeolites, because the synthesis occurs at high driving forces, where the barriers for nucleation are negligible. This project unveiled that polymorph selection in zeolite synthesis occurs after nucleation, opening a distinct area of control through the kinetics of growth and not through nucleation barriers.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Tactile Game System

The board game industry revenue has seen rapid growth from 6.2 billion USD to a projected 8.6 billion USD in revenue from 2018 to 2024 indicating an increased demand for this style of product. Inflation, shipping and the cost of raw materials have increased the cost for producing board games. This increased the barrier of entry and reduces profit margins. Many people lose the chance to experience much of the catalogue of modern hobby board games because of this. There is a need for a digital and low-cost solution for buyers to fulfill demand and create a steady supply while maintaining the characteristics that make board games attractive to consumers. Lowering the barrier of entry will allow for more consumers to enter the market and provide a catalyst for growth in the board game community.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2024

Improved Creep Testing Approach for Bentonite EBS

In the United States, the nuclear reactor contributes 18.7 percent of the nation’s total electricity generation and produces a significant amount of spent nuclear fuel (SNF) and high-level waste. Because SNF is being stored for longer periods than initially envisioned, the U.S. Department of Energy Office of Nuclear Energy, Office of Spent Fuel and Waste Science and Technology is assessing the technical performance of the SNF storage systems after extended durations. The concept of a sustainable geologic repository for SNF disposal relies heavily on the safety provided by multiple barriers, such as repository host rock, overlying rock formation, and human-made engineered barrier systems (EBS). One of the major components of EBS is bentonite-based buffer materials that isolate the nuclear-waste canisters from the host rock and fill the void left in the horizontally drilled boreholes. The resaturated bentonite has a swelling characteristic, which is useful for self-sealing the microcracks in the host rock and supporting the canister’s heavy weight. However, factors such as nonuniformity in the saturation, swelling pressure of bentonite, and the high temperature at the canister-bentonite interface may lead to instability of the waste canister inside the borehole. Therefore, evaluating the long-term deformation of bentonite-based material is necessary. RESPEC Company, LLC recently completed a preliminary study for the U.S. Department of Energy (DE SC0022804) that is attempting to understand the time-dependent deformation in the consolidated sand/bentonite (SB) specimens through triaxial creep experiments and improve the understanding of EBS performance under anticipated repository conditions. The project included developing a standard testing procedure for preparing the consolidated core specimen from a mixture of sand and bentonite in a 50:50 ratio by weight, fabricating a new pressure vessel in-house, modifying existing creep equipment to perform triaxial creep experiments on consolidated SB specimens, and performing six long-term triaxial creep experiments under low-deviatoric stress at two different temperature conditions, which is representative of hypothetical conditions that might be encountered in a geologic repository within a reasonable rate of success in completing creep experiments. The consolidated SB specimen was prepared using the novel specimen preparation procedure and had physical characteristics (e.g., moisture content and bulk density) reasonably comparable with the properties of bentonite-based buffer, which is proposed to be used in the EBS in the Swedish KBS-3H design and the Swiss design of SNF disposal in the horizontal drifts. The newly fabricated pressure vessel could withstand the confining pressure of up to 15 megapascals (MPa) while maintaining the test temperature of up to 90 degrees Celsius (°C) for long-term creep experiments. The preliminary results from the triaxial creep experiments suggested that the consolidated SB specimen may experience time-dependent deformation at a low-deviatoric stress state and room temperature condition. Based on the deformation recorded in the SB specimen from axial and radial linear variable differential transformers (LVDTs) and physical characteristic changes, it is apparent that the time-dependent deformation is a combination of consolidation and creep, which is influenced by the level of deviatoric stresses and temperature. The systematic creep testing of bentonite-based specimens helped develop a standard testing procedure applicable for analyzing the similar characteristics of shale or clay-like materials in different geologic conditions outside repository science, including in civil engineering and infrastructure projects, underground and open pit mining, and deep drilling.

58 GEOSCIENCES↗
DOE OSTI2023

Assessment of Process Modeling Tools for Determining Variability in Additively Manufactured Parts

The Advanced Materials and Manufacturing Technologies (AMMT) program aims to accelerate the development, qualification, demonstration, and deployment of advanced materials and manufacturing technologies to enable reliable and economical nuclear energy However, the unique aspects of additive manufacturing (AM) materials in terms of their processing history, microstructure, and properties, are a major barrier for qualification and certification of nuclear components. Much of this challenge may be attributed to component scale variations in microstructure and properties that are driven by local influences of process conditions and geometry on thermal history, melt pool dynamics, and corresponding microstructure evolution. Computational modeling tools may be helpful in this regard to aid in predicting and controlling this level of variability. The purpose of this report is to review the current state-of-the-art for process modeling with regards to metal AM. For this purpose, we consider specifically the case study of laser powder bed fusion (LPBF) processing of SS316, a family of alloys that are both commonly used in nuclear energy applications and suitable for AM processing. The report first introduces the necessary components of a process modeling workflow, followed by a review of the current status of each. At the end, application of these modeling tools to understanding variability in AM process given their current state are considered, and recommendations for future development are proposed

36 MATERIALS SCIENCE↗
DOE OSTI2021

Opening band gaps of low-dimensional materials at the meta-GGA level of density functional approximations

The quasiparticle band structure can be properly described by Hedin's GW approximation (GW), at a high computational cost. For band gaps, semilocal density functionals up to the generalized gradient approximation (GGA) level cannot compete with the accuracy of hybrid-based approximations or GW. Meta-GGA density functionals with a strong dependence on the kinetic energy density ingredient can potentially give wider band gaps compared with GGAs. The recent TASK meta-GGA density functional from Aschebrock and Kümmel [ Phys. Rev. Research 1 , 033082 (2019) ], is constructed with an enhanced nonlocality in the generalized Kohn-Sham scheme and therefore harbors great opportunities for band gap prediction. Although this approximation was found to yield excellent band gaps of bulk solids, this accuracy cannot be straightforwardly transferred to low-dimensional materials. Additionally, the reduced screening of these materials results in larger band gaps compared with their bulk counterparts, as an additional barrier to overcome. In this paper we demonstrate how the alteration of this functional affects the band gaps of monolayers and nanoribbons and present accurate band gaps competing with the revised Heyd-Scuseria-Ernzerhof (HSE06) approximation. In order to achieve this goal, we have modified the TASK functional (a) by changing the tight upper bound for one- or two-electron systems ( h X 0 ) from 1.174 to 1.29 and (b) by changing the limit of the interpolation function f X ( α → ∞ ) of the TASK functional that interpolates the exchange enhancement factor F X ( s , α ) from α = 0 to 1. The resulting modified TASK (mTASK) was tested for various materials from three dimensions to two dimensions to one dimension (nanoribbons) and was compared with the results of the higher-level hybrid functional HSE06 or with the G 0 W 0 approximation within many-body perturbation theory. We find that mTASK systematically improves the band gaps and band structures of two-dimensional (2D) and 1D systems, without significantly affecting the accuracy of the original TASK for the bulk 3D materials, when compared with the Perdew-Burke-Ernzerhof (PBE) GGA and the strongly constrained and appropriately normed (SCAN) meta-GGA. We further demonstrate the applicability of mTASK by assessing the band structures of transition metal dichalcogenide nanoribbons with respect to various bending curvatures.

36 MATERIALS SCIENCE↗
DOE OSTI2025

First-Principles Assessment of ZnTe and CdSe as Prospective Tunnel Barriers at the InAs/Al Interface

Majorana zero modes are predicted to emerge in semiconductor/ superconductor interfaces, such as InAs/Al. Majorana modes could be utilized for fault tolerant topological qubits. However, their realization is hindered by materials challenges. The coupling between the superconductor and the semiconductor may be too strong for Majorana modes to emerge, due to effective doping of the semiconductor by the metallic contact. This could be mediated by adding a tunnel barrier of controlled thickness. We use density functional theory (DFT) with Hubbard U corrections, whose values are machine-learned via Bayesian optimization (BO), to assess ZnTe and CdSe as prospective tunnel barriers for the InAs/Al interface. The results of DFT +U(BO) for ZnTe are validated by comparison to angle resolved photoemission spectroscopy (ARPES). We then study bilayer interfaces of the three semiconductors with each other and with Al, as well as trilayer interfaces with a varying number of ZnTe or CdSe layers inserted between InAs and Al. We find that 16 atomic layers of either material completely insulate the InAs from metal induced gap states (MIGS). However, ZnTe and CdSe differ significantly in their band alignment, such that ZnTe forms an effective barrier for electrons, whereas CdSe forms a barrier for holes. Because of Fermi level pinning in the conduction band at the interface, only electron transport is relevant for InAs-based Majorana devices. Therefore, ZnTe is the better choice. Based on the results of our simulations, we suggest conducting experiments with ZnTe barriers in the thickness range of 6–18 atomic layers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗