SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Five-port ganged valve isolates collector from primary load system pressure and drains collectors, allowing use of direct heating with all its advantages. Valve is opened and closed by same switch that controls pump or by temperature sensor set at O C, while providing direct dump option.
Valve assembly keeps nutrient out of moving parts of valve by physically isolating plunger from fluid. Poppet and diaphragm are molded together, and latter is shaped to act as static seal, which remains seated during the operation. As plunger moves, diaphragm also moves to form separate cavity for nutrient and thus isolates it from plunger cavity and latching mechanism.
Curing technique for producing variable viscosity seal has hard sealing surface supported by softer rubber. Valve seal is clamped between two jaws for curing with hotter jaw at temperature of approximately 350 F and lower at room temperature. Result is durable tight valve-seat.
A stability-bleed system was installed in a YF-12 flight inlet that was subjected to internal and external airflow disturbances in the NASA Lewis 10 by 10 foot supersonic wind tunnel. The purpose of the system is to allow higher inlet performance while maintaining a substantial tolerance (without unstart) to internal and external disturbances. At Mach numbers of 2.47 and 2.76, the inlet tolerance to decreases in diffuser-exit corrected airflow was increased by approximately 10 percent of the operating-point airflow. The stability-bleed system complemented the terminal-shock-control system of the inlet and did not show interaction problems. For disturbances which caused a combined decrease in Mach number and increase in angle of attack, the system with valves operative kept the inlet started 4 to 28 times longer than with the valves inoperative. Hence, the stability system provides additional time for the inlet control system to react and prevent unstart. This was observed for initial Mach numbers of 2.55 and 2.68. For slow increase in angle of attack at Mach 2.47 and 2.76, the system kept the inlet started beyond the steady-state unstart angle. However, the maximum transient angles of attack without unstart could not be determined because wind-tunnel mechanical-stop limits for angle of attack were reached.
In hypokinesia, edema of all the layers of the mitral value was observed, which resulted in morphological changes of the cellular and noncellular components. An increase in ratio of elastic and collagenic fibers in the value was also observed along with and changes in their structural and staining properties. The observed changes can limit valve mobility and can result in manifestations of cardiac valve insufficiency, which is found clinically.
Sliding-gate valve originally developed for rocket exhaust-gas ducts is sealed by a Belleville spring. It is simple, compact, and operates over a wider range of temperatures than conventional O-ring sealed valves.
A chemical vapor deposited tungsten with dispersed carbides was selected as the material for Space Shuttle Orbital Maneuvering and Reaction Control Systems check valve poppets and seats. The selection followed a NASA-sponsored prototype check valve development program utilizing the cutter-seal shell poppet concept. The poppet material is deposited as a coating approximately 0.9 mm thick and fabricated into a shell as a free standing body. The seat material is deposited as a coating 1.1 mm thick on a seat blank, and the cutter seal is machined in the coating. Module tests demonstrated that the material could be ground and lapped to very sharp edges and could cut through typical system contaminants without excessive damage to the sealing surfaces. The material was also determined to be unaffected by exposure to a strongly oxidizing storable propellant.
Bent rod on modified basin wrench holds wrench jaw against valve stem. Rod swivels to accomodate 180 degrees rotation of wrench jaw. Valves 5 feet (1.5 meters) underground can be operated with tool.
Processing changes improve performance of liquid-crystal light valve for displaying projection TV images. New approach monitors performance of finished light valves for given changes in CdS process and experimentally to optimize process for good sensitivity and low negative memory.
Proposed valve employs ferrofluid to make tight seal. Seal requires no precisely machined parts, and hand lapping of valve seats are unnecessary. Magnetic fluid fills gap between shaft and annular pole piece in chamber wall. Precise shaft fit is not necessary.
Flow-straightening sleeve contains vanes in modified honeycomb pattern. Each vane curved fluid-dynamic wing that helps straighten and smooth out flow of fluid passing over it. Sleeve performs more reliably and quietly, possibility of damage to internal valve parts greatly reduced, valve life expectancy increased and time between overhauls extended.
Remotely-controlled cryogenic valve operates over temperature range from room temperature to 2 K. Valve used in helium dilution refrigerators, cryostats and adiabatic-demagnetization refrigerators.
Simple device vents excess low-pressure gas. Inexpensive pressure relief valve built from polyvinylchloride pipe. Valve suitable for low pressure-- 25 to 50 cm of mercury-- and flow rates up to 14 m3/min.
Small subvalves opened and closed simultaneously. Precisely-machined mating rings act as valves. Rings seal against each other to stop fluid flow. Rings deformed or moved relative to each other to uncover holes and permit flow. Valve controls flow rate of fuel into burner.
Optical addition and storage units are described in this paper. These units are implemented using the Hughes Liquid Crystal Light Valve (LCLV) as a spatial light modulator using residue arithmetic for a numerical representation. The main hardware components of the design, besides the light valve, include an array of single-mode optical fibers that provide input information, a polarizing prism in combination with quarter-wave and half-wave retarders for residue arithmetic implementation in the adder, and a holographic array for spatial stability in the storage unit.
The linear motion valve is described. The valve spool employs magnetically permeable rings, spaced apart axially, which engage a sealing assembly having magnetically permeable pole pieces in magnetic relationship with a magnet. The gap between the ring and the pole pieces is sealed with a ferrofluid. Depletion of the ferrofluid is minimized.
An improved photosensor film and liquid crystal light valves embodying said film is provided. The photosensor film and liquid crystal light valve is characterized by a significant lower image retention time while maintaining acceptable photosensitivity. The photosensor film is produced by sputter depositing CdS onto an ITO substrate in an atmosphere of argon/H2S gas while maintaining the substrate at a temperature in the range of about 130 C to about 200 C and while introducing nitrogen gas into the system to the extent of not more than about 1% of plasma mixture. Following sputter deposition of the CdS, the film is annealed in an inert gas at temperatures ranging from about 300 C to about 425 C.
Double-ring seal avoids expense of remachining or redesigning valve parts. Mating fittings on valve sealed by pair of rings - one O-ring and backup ring. Backup ring fills relatively large gap between parts. Prevents softer O-ring from being pushed into and through gap.