Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “solid state”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21

Fluorinated solid electrolyte interphase enables highly reversible solid-state Li metal battery

Solid-state electrolytes (SSEs) are receiving great interest because their high mechanical strength and transference number could potentially suppress Li dendrites and their high electrochemical stability allows the use of high-voltage cathodes, which enhances the energy density and safety of batteries. However, the much lower critical current density and easier Li dendrite propagation in SSEs than in nonaqueous liquid electrolytes hindered their possible applications. Herein, we successfully suppressed Li dendrite growth in SSEs by in situ forming an LiF-rich solid electrolyte interphase (SEI) between the SSEs and the Li metal. The LiF-rich SEI successfully suppresses the penetration of Li dendrites into SSEs, while the low electronic conductivity and the intrinsic electrochemical stability of LiF block side reactions between the SSEs and Li. The LiF-rich SEI enhances the room temperature critical current density of Li 3 PS 4 to a record-high value of >2 mA cm -2 . Moreover, the Li plating/stripping Coulombic efficiency was escalated from 88% of pristine Li 3 PS 4 to more than 98% for LiF-coated Li 3 PS 4 . In situ formation of electronic insulating LiF-rich SEI provides an effective way to prevent Li dendrites in the SSEs, constituting a substantial leap toward the practical applications of next-generation high-energy solid-state Li metal batteries.

25 ENERGY STORAGE↗

Solid state systems concepts

Two prototype solid state phased array systems concepts for potential use in the Solar Power Satellite are described; the end-mounted and the sandwich systems. In both concepts, the beam is centered on the rectenna by means of phase conjugation of a pilot signal emanating from the ground. In the end-mounted system 36-watt amplifiers are mounted on the ground-plane, whereas in the sandwich the amplifiers are elevated to the dipoles, and their waste heat is dissipated by beryllium oxide discs. The feed lines are underneath the ground-plane, and a coaxial transmission line is carried all the way to the amplifier input. Also discussed is solid state amplifier development.

Schroeder, I. K.↗

Solid electrolytes and interfaces in all-solid-state sodium batteries: Progress and perspective

All-solid-state sodium batteries are promising candidates for the next generation of energy storage with exceptional safety, reliability and stability. The solid electrolytes are key components for enabling all-solid-state sodium batteries with high electrochemical performances. This Review discusses the current developments on inorganic and organic sodium ions solid electrolytes, including β/β’’-alumina, NASICON, sulfides, polymers and others. In particular, the structures, ionic conductivities and fabrications as well as electrochemical/chemical stabilities of solid electrolytes are discussed. Furthermore, the effective approaches for forming intimate interfaces between solid electrolytes and electrodes are also reviewed. And perspectives on future developments in the field of solid electrolytes and possible directions to improve interfacial contacts for future practical applications of all-solid-state sodium batteries are included.

25 ENERGY STORAGE↗

Electron and solid state physics

Electron and solid state physics - reflected light, Raman effects, solid and liquid optical properties, spectroscopy, Brillouin effects, and carbon dioxide laser

BRILLOUIN EFFECT↗

Garnet-rich composite solid electrolytes for dendrite-free, high-rate, solid-state lithium-metal batteries

Composite solid electrolytes (CSEs), which are composed of inorganic fillers and organic polymers, show improved safety and suppressed lithium dendrite growth in Li-metal batteries, as compared to flammable liquid electrolytes. However, the performance of current CSEs is limited by the agglomeration effect, with low content of inorganic Li + -conducting fillers and ineffective Li + transport between the inorganic fillers and the polymer matrix. To address these challenges, a new type of CSE composed of silane-modified Li 6.28 La 3 Al 0.24 Zr 2 O 12 (s@LLAZO) nanofibers and poly(ethylene glycol) diacrylate (PEGDA) is developed. Employment of the silane coupling agent, 3-(trimethoxysilyl)propyl methacrylate, enables the incorporation of a high content of LLAZO nanofibers (up to 70 wt%) with the polymer matrix and results in a well-percolated, three-dimensional LLAZO network fully embedded in the PEGDA matrix. Consequently, the silane coupling agent successfully eliminates the agglomeration effect, which ensures higher ionic conductivity, larger lithium transference number, wider electrochemical stability window, and better cycling stability for s@LLZAO-PEGDA CSEs. Excellent cycling stability and extraordinarily high rate capability (up to 10C) are demonstrated in the all-solid-state Li-metal batteries with LiFePO 4 and high-voltage Li[Ni 1/3 Mn 1/3 Co 1/3 ]O 2 cathodes at ambient temperature. This novel design of CSEs with s@LLAZO nanofibers paves the way for a new generation of improved functioning all-solid-state Li-metal batteries.

25 ENERGY STORAGE↗

Development of Thin, Robust, Lithium-Impenetrable, HighConductivity, Electrochemically Stable, Scalable, and Low-Cost Glassy Solid Electrolytes for Solid State Lithium Batteries (Final Report)

Solid-state electrolytes (SSEs) must have thicknesses of < 50 microns in order to be competitive with current state-of-the-art organic liquid electrolyte batteries. Mixed oxy-sulfide-nitride (MOSN) glassy solid electrolytes (GSEs) can be drawn into thin ribbons using the glass redraw process, to form glasses with superior performance in a safe, lower-cost, monolithic glass film. It is expected that these new GSEs in solid-state lithium batteries (SSLBs) increase the energy density (anode basis) from ~300 mAh/g to ~ 4000 mAh/g. This project is focused on the development of candidate MOS GSE compositions, and optimization of the thin film drawing process to generate thin film glass ribbons for use in SSLBs.

25 ENERGY STORAGE↗

Solid-State Lithium/Selenium–Sulfur Chemistry Enabled via a Robust Solid-Electrolyte Interphase

Lithium/selenium-sulfur batteries have recently received considerable attention due to their relatively high specific capacities and high electronic conductivity. Different from the traditional encapsulation strategy for suppressing the shuttle effect, an alternative approach to directly bypass polysulfide/polyselenide formation via rational solid-electrolyte interphase (SEI) design is demonstrated here. It is found that the robust SEI layer that in situ forms during charge/discharge via interplay between rational cathode design and optimal electrolytes could enable solid-state (de)lithiation chemistry for selenium-sulfur cathodes. Hence, Se-doped S 22.2 Se/Ketjenblack cathodes can attain a high reversible capacity with minimal shuttle effects during long-term and high rate cycling. Moreover, the underlying solid-state (de)lithiation mechanism, as evidenced by in situ 7 Li NMR and in operando synchrotron X-ray probes, further extends the optimal sulfur confinement pore size to large mesopores and even macropores that have been long considered as inferior sulfur or selenium host materials, which play a crucial role in developing high volumetric energy density batteries. It is expected that the findings in this study will ignite more efforts to tailor the compositional/structure characteristics of the SEI layers and the related ionic transport across the interface by electrode structure, electrolyte solvent, and electrolyte additive screening.

(de)lithiation chemistry↗

Tunable Crosslinked Ether Polymer Network Electrolytes for High‐Performance All‐Solid‐State Sodium Batteries

All-solid-state batteries (ASSBs) are critical for achieving high energy density and enhanced safety. Solid polymer electrolytes (SPEs) offer key advantages over other electrolytes, including improved safety, flexibility, and interfacial contact. Among the SPEs, ether-based polymers are widely studied due to their ease of processing and high ionic conductivity (σi) in the amorphous state. In this work, the introduction of poly(ethylene glycol) methyl ether methacrylate (PEGMEMA) into an SPE matrix composed of poly(ethylene glycol) diacrylate (PEGDA), poly(ethylene glycol) (PEG2k), and sodium bis(fluorosulfonyl)imide (NaFSI) salt is investigated to facilitate the formation of amorphous, high σ i SPEs through end-group engineering and polymer ratio optimization. PEGMEMA enhances structural integrity via crosslinking with PEGDA through its methacrylate group, while its methyl end group aids ion conduction. A 2:1:7 ratio of PEGDA:PEGMEMA:PEG2k exhibits a σi of 1.16 x 10 -4 S cm -1 and oxidative stability up to 4.4 V at 60 °C. A solid-state cell incorporating this SPE, a Na 2/3 Ni 1/3 Mn 2/3 O 2 (NM12) cathode, and a sodium-metal anode demonstrates excellent cycling stability, retaining over 80 % of its initial capacity for 150 cycles at 60 °C. The findings highlight the potential of end-group engineering in improving the electrochemical performance of SPEs.

25 ENERGY STORAGE↗

Advances in solid-state NMR for the studies of mesoporous solids: fast magic spinning and dynamic nuclear polarization

Here, this review provides an up-to-date account of the development of two solid-state (SS)NMR methods for enhancing resolution and sensitivity, fast magic angle spinning (MAS) and dynamic nuclear polarization (DNP), and the resulting progress in surface science. We demonstrate the high resolution and efficiency that can be achieved by using two-dimensional homo- and heteronuclear correlation experiments with small rotors capable of MAS at rates exceeding 100 kHz. DNP has offered significant enhancements in signal sensitivity and allowed access to nuclei and experiments that are beyond the limits of conventional SSNMR. The continuing progress in fast MAS and DNP methodologies in recent years generated an unprecedented shift in SSNMR’s capabilities in the studies of surface and interface regions of solids, especially mesoporous supports and catalysts. We give numerous examples of recent applications and discuss the prospects for further improvements of both methods.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

A Plastic–Crystal Electrolyte Interphase for All‐Solid‐State Sodium Batteries

Abstract The development of all‐solid‐state rechargeable batteries is plagued by a large interfacial resistance between a solid cathode and a solid electrolyte that increases with each charge–discharge cycle. The introduction of a plastic–crystal electrolyte interphase between a solid electrolyte and solid cathode particles reduces the interfacial resistance, increases the cycle life, and allows a high rate performance. Comparison of solid‐state sodium cells with 1) solid electrolyte Na 3 Zr 2 (Si 2 PO 4 ) particles versus 2) plastic–crystal electrolyte in the cathode composites shows that the former suffers from a huge irreversible capacity loss on cycling whereas the latter exhibits a dramatically improved electrochemical performance with retention of capacity for over 100 cycles and cycling at 5 C rate. The application of a plastic–crystal electrolyte interphase between a solid electrolyte and a solid cathode may be extended to other all‐solid‐state battery cells.

Gao, Hongcai↗

Wideband Waveform Design principles for Solid-state Weather Radars

The use of solid-state transmitter is becoming a key part of the strategy to realize a network of low cost electronically steered radars. However, solid-state transmitters have low peak powers and this necessitates the use of pulse compression waveforms. In this paper a frequency diversity wideband waveforms design is proposed to mitigate low sensitivity of solid-state transmitters. In addition, the waveforms mitigate the range eclipsing problem associated with long pulse compression. An analysis of the performance of pulse compression using mismatched compression filters designed to minimize side lobe levels is presented. The impact of range side lobe level on the retrieval of Doppler moments are presented. Realistic simulations are performed based on CSU-CHILL radar data and Center for Collaborative Adaptive Sensing of the Atmosphere (CASA) Integrated Project I (IP1) radar data.

54 ENVIRONMENTAL SCIENCES↗

Fabricating Solid-State Batteries for Electric Aviation

All-solid-state lithium batteries are widely reputed as the next major step in energy storage technology on account their drastically improved safety over wet cells, as solid electrolytes lack the volatile compounds in wet electrolytes that make them combustible. This enhanced safety enables a far wider range of products and vehicles to go fully electric and aligns with future NASA missions that require high performing, reliable, and safe batteries. However, they currently face issues with implementation in consumer products due to the often-poor mechanical properties of the solid electrolyte and relative difficulty to manufacture. Typical solid-state electrolyte challenges were bypassed by incorporating a range of polymeric binders into a solid electrolyte suspension and cast onto a composite carbon-sulfide cathode to create a single bilayer film. The resulting films display superior flexibility and durability compared to solid-electrolyte films typically discussed in literature without compromising the thinness of the films. The bilayer film was then punched into 12.7 cm diameter discs and 4 cm by 5 cm sheets, pressed, and assembled into coin cells and pouch cells respectively.

Batteries↗

All-optical quantum computing with a hybrid solid-state processing unit

We develop an architecture of a hybrid quantum solid-state processing unit for universal quantum computing. The architecture allows distant and nonidentical solid-state qubits in distinct physical systems to interact and work collaboratively. All the quantum computing procedures are controlled by optical methods using classical fields and cavity QED. Our methods have a prominent advantage of the insensitivity to dissipation process benefiting from the virtual excitation of subsystems. Moreover, the quantum nondemolition measurements and state transfer for the solid-state qubits are proposed. The architecture opens promising perspectives for implementing scalable quantum computation in a broader sense that different solid-state systems can merge and be integrated into one quantum processor afterward.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Halide segregation to boost all-solid-state lithium-chalcogen batteries

Mixing electroactive materials, solid-state electrolytes, and conductive carbon to fabricate composite electrodes is the most practiced but least understood process in all-solid-state batteries, which strongly dictates interfacial stability and charge transport. Here, we report on universal halide segregation at interfaces across various halogen-containing solid-state electrolytes and a family of high-energy chalcogen cathodes enabled by mechanochemical reaction during ultrahigh-speed mixing. Bulk and interface characterizations by multimodal synchrotron x-ray probes and cryo–transmission electron microscopy show that the in situ segregated lithium halide interfacial layers substantially boost effective ion transport and suppress the volume change of bulk chalcogen cathodes. Various all-solid-state lithium-chalcogen cells demonstrate utilization close to 100% and extraordinary cycling stability at commercial-level areal capacities.

36 MATERIALS SCIENCE↗

Solid-State Hydriding Mechanism in the LiBH4 + MgH2 System

The LiBH4+MgH2 system has great potential in reversible hydrogen storage for fuel cell vehicles. However, it has always been dehydrogenated and re-hydrogenated in the liquid state until recently. The solid-state hydriding and dehydriding are necessary in order to achieve hydrogen uptake and release near the ambient temperature. In this study, the solid-state hydriding mechanism of 2LiH+MgB2 mixtures has been investigated for the first time. It is found that the solid-state hydriding proceeds in two elementary steps. The first step is the ion exchange between the Mg2+ and Li+ ions in the MgB2 crystal to form an intermediate compound (Mg1-xLi2x)B2. The second step is the continuous ion exchange and simultaneous hydrogenation of (Mg1-xLi2x)B2 to form LiBH4 and MgH2. This finding is consistent with the observed diffusion-controlled hydriding kinetics.*

08 HYDROGEN↗

Solid-State Hydrogen Storage: Storage Capacity,Thermodynamics and Kinetics

Solid-state reversible hydrogen storage systems hold great promise for on-board applications. The key criteria for a successful solid-state reversible storage material are high storage capacity, suitable thermodynamic properties, and fast hydriding and dehydriding kinetics. The LiNH2 + LiH system has been utilized as an example system to illustrate these critical issues that are common among other solid-state reversible storage materials. The progress made in thermodynamic destabilization and kinetic enhancements via various approaches have been emphasized. The implications of these advancements in the development of future solid-state reversible hydrogen storage materials are discussed.

08 HYDROGEN↗

Promising performance of sulfide catholytes compared to halide alternatives in NMC811 cathodes for sheet-type sulfide solid-state batteries

Sulfide-based solid-state batteries (SSBs) show promise in achieving energy densities over 350 Wh/kg, yet challenges persist with their incorporation of high-voltage, nickel-rich layered oxide cathodes, such as LiNi₀.₈Mn₀.₁Co₀.₁O₂ (NMC811), due to the poor oxidation stability of sulfide solid-state electrolytes (SSEs) like Li₆PS₅Cl (LPSCl). Although halide SSEs such as Li₃InCl₆ (LIC) and Li₃YCl₆ (LYC) have previously shown promise in stabilizing high-voltage NMC cathodes, our research reveals that sulfide SSE catholytes, particularly when combined with surface-coated NMC cathodes, deliver superior performance. Here, this investigation assesses the cycling stability of various catholytes—LPSCl, LIC, Li₁₀GeP₂S₁₂ (LGPS), combined LIC-LPSCl, and LYC-LPSCl—in SSBs with LiNbO₃-coated NMC811 cathodes against sheet-type LPSCl separators. Findings indicate that while LGPS-based cathodes maintain higher capacity retention, they yield lower deliverable capacity, and LIC cathodes experience significant electrochemical degradation. Importantly, our results underscore that sulfide SSE catholytes, in conjunction with LiNbO₃-coated cathodes, optimize the cathode-electrolyte interphase (CEI), enhancing both kinetics and mass transport. These insights provide a strategic direction for optimizing catholyte composition in the development of sheet-type sulfide-based SSBs.

Catholyte↗

A Cellular Automaton Simulation for Predicting Phase Evolution in Solid-State Reactions

New computational tools for solid-state synthesis recipe design are needed in order to accelerate the experimental realization of novel functional materials proposed by high-throughput materials discovery workflows. This work contributes a cellular automaton simulation framework for predicting the time-dependent evolution of intermediate and product phases during solid-state reactions as a function of precursor choice and amount, reaction atmosphere, and heating profile. The simulation captures the effects of reactant particle spatial distribution, particle melting, and reaction atmosphere. Reaction rates based on rudimentary kinetics are estimated using density functional theory data from the Materials Project and machine learning estimators for the melting point and the vibrational entropy component of the Gibbs free energy. The resulting simulation framework allows for the prediction of the likely outcome of a reaction recipe before any experiments are performed. We analyze five experimental solid-state recipes for BaTiO 3 , CaZrN 2 , and YMnO 3 found in the literature to illustrate the performance of the model in capturing reaction selectivity and reaction pathways as a function of temperature and precursor choice. This simulation framework offers an easier way to optimize existing recipes, aid in the identification of intermediates, and design effective recipes for yet unrealized inorganic solids in silico .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗