Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “performance test”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 379 records · Page 21
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Performance of sweeping gas membrane distillation for treating produced water: Modeling and experiments

Membrane distillation (MD) has shown promise for desalination of produced water (PW), but there are very few studies reported on the performance of MD with real PW and the characteristics of the fouling and scaling in MD. Among different MD configurations, sweeping gas MD (SGMD) is the least studied configuration. Here we report the application of SGMD for treating high-salinity PW (123 g L -1 ). The SGMD operating conditions were first carefully optimized through pure water MD experiments by varying operating conditions. The flux evaluation was accompanied by a detailed Aspen Custom Modeler simulation based on the electrolyte-NRTL thermodynamic model to better understand the heat and mass transfer in the feed and permeate channel. Supported by experiments, modeling results confirmed the partial condensation of the vapor in the permeate channel. Furthermore, it was concluded that the saturation of the sweeping gas is controlling the overall mass transfer through the membrane. Selected membranes and optimized conditions were then used to conduct short-term and long-term performance tests with PW. In long-term MD test, the concentration of the PW increased by a factor of two (50% water recovery), while the membrane exhibited small flux decline. Elemental analysis showed that strontium and sodium were the major scalant compounds.

42 ENGINEERING↗
DOE OSTI2025

Non-destructive electrochemical diagnosis of failure mechanisms in aqueous zinc batteries

The early detection of secondary reactions that affect the life and performance of zinc manganese oxide batteries requires a shift from conventional time-consuming and often destructive procedures to rapid lifetime-predictive techniques. In this work, an electrochemical approach is employed to elucidate independent signatures for four common types of failure mechanisms in zinc manganese dioxide (Zn||MnO2) batteries—namely, the loss of zinc inventory, the loss of active material at the cathode, electrolyte depletion, and increased cell impedance. Our findings, specific to coin cell configurations, reveal that each induced failure mechanism can be distinctively modeled and identified based on responses from the rest voltage and columbic-efficiency data for prompt detection. For instance, electrolyte depletion response manifests a distinctive abrupt (>80 %) decrease in columbic efficiency (CE) and charge-rest voltage (Vc) while the discharge-rest voltage remained constant at ~1.3 V. Furthermore, electrolyte rejuvenation of the cell increased the CE to >95 % and restored Vc from ~0.3 to >1.7 V. Recovery experiments and reference performance tests demonstrated consistency between electrochemical descriptors and their associated failure mechanisms. Further, the outcomes of this work provide valuable insights and data models for some of the dominant failure mechanisms present in zinc manganese battery chemistries, which are beneficial to accelerated early-lifetime diagnosis and advancement of Zn batteries development.

25 ENERGY STORAGE↗
DOE OSTI2026

Process control-enabled mitigation of microstructural and plastic heterogeneities in additively manufactured Grade 91 steel

Synergizing wire arc-directed energy deposition (WA-DED) additive manufacturing (AM) with particle-strengthened creep strength-enhanced ferritic (CSEF) steels enables fabrication and repair of critical power-plant components. Investigations focused on fusion-welded particle-strengthened CSEF steels, such as Grade 91 steel, have linked microstructurally heterogeneous regions—forming due to heat affected zones (HAZ)—with premature failure during elevated temperature service. Fusion-based AM, including WA-DED, likewise generates microstructurally and plastically heterogeneous regions due to spatiotemporally varying thermokinetics during deposition. However, works investigating such microstructural heterogeneities, their implications for mechanical behavior, and strategies to mitigate their formation remain scarce. This work identifies microstructurally and plastically heterogeneous regions within the WA-DED-processed Grade 91 steel. Spatial microhardness variations in the as-fabricated specimen correlate with the variation in the attributes of grain, martensitic microstructure, and precipitates across the fusion zone and HAZ. Digital image correlation-enabled tensile tests performed at 500 °C revealed pronounced deformation localization and a wave-like strain distribution, with wavelength close to the melt pool depth, indicating susceptibility of the as-fabricated components to premature creep failure. Such heterogeneity in microstructural and mechanical behavior was attributed to recurring solid-state phase transformations. Subsequently, an interlayer temperature control strategy was implemented, wherein maintaining interlayer temperature above the martensitic start temperature mitigated the heterogeneous microstructural and plastic response in the as-fabricated condition. Findings open pathways to achieving deformation-localization- and creep-resistant microstructures in WA-DED fabricated particle-strengthened CSEF steel components, reducing reliance on post-welding heat treatments—conventionally required to enhance creep resistance—and enabling on-demand, short lead-time fabrication of next-generation power-plant components.

Heat affected zones↗
DOE OSTI2025

An atomistic study connecting underlying dislocation behavior with superior mechanical properties of NiCoCr medium entropy alloy

NiCoCr-based medium-entropy alloy (MEA) with a simple face-centered cubic crystal phase exhibits excellent mechanical properties, often attributed to the synergy of multiple deformation mechanisms. However, the atomistic origin of their outstanding mechanical response, including microstructural evolution and dislocation behavior under varying strain-rates and orientation, remains unclear. In this work, we employ large-scale molecular dynamics (MD) simulations to investigate the changes in deformation mechanisms along three distinct orientations ([110], [111], [100]) under varying strain rates (1 ×10 8 /sec, 1 ×10 10 /sec, 1 ×10 12 /sec) in the NiCoCr MEA. The presence of the stair-rod and the Shockley partial dislocations under uniaxial tensile strain are found to play a key role in the formation of deformation twinning and ε-martensite, which positively correlates with strain-rate dependent dislocation analysis. These findings further establish the role of the dislocations in controlling the superior mechanical response and excellent fracture toughness of the NiCoCr MEA. Systematic transmission-electron microscopy tests performed on the [111]-oriented crystals, deformed at different strain levels, at room temperature provide clear evidence of both the extended stacking-fault and the stair rods, confirming the predicted microstructural features. Finally, this study offers key insights into the complex nucleation mechanisms of deformation twinning and ε-martensite, such as twinning – and transformation–induced plasticity (TWIP-TRIP), providing valuable guidelines for studying similar material classes.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Cryogenic electronics for noble liquid neutrino detectors

In this paper we present the general features of cryogenic (or “cold”) electronics for noble liquid time projection chambers, with design principles and details for neutrino physics, a brief history of the technology and details of recent research and development that is driving the design of the detectors under construction. Finally, some comments on future R&D envisioned and the impact of this work on other fields is described. “Cold” in the context of this work applies to CMOS devices operated at 77 K and above, at liquids temperatures of LAr (89 K), LKr (125 K) and LXe (165 K), with most of the tests performed in, or at LN 2 (77 K). Additionally, the paper is concentrated on the design of cold electronics for large liquid argon TPCs, those that have been successfully operated, MicroBooNE and ProtoDUNE, and those designed or under construction, such as SBND and DUNE first and second 10 kton modules. The high performance achieved with MicroBooNE and ProtoDUNE – a high signal-to-noise ratio combined with high stability of response – is mainly due to the integral approach to design and construction of sensing electrodes with cold readout electronics in a modular approach with the cryostat signal feed-throughs incorporating warm interface electronics into a Faraday cage with the cryostat. The integral concept is described in some detail in this paper.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2023

An automated QC station for the calibration of the Mu2e calorimeter readout units

The Mu2e calorimeter will employ Readout Units, each made of two Silicon Photomultipliers arrays and two Front End Electronics boards. To calibrate them, we have designed, assembled and put in operation an automated Quality Control (QC) station. Gain, collected charge and photon detection efficiency are evaluated for each unit. Here, in this paper, the QC Station is presented, in its hardware and software aspects, summarizing also the tests performed on the ROUs and the first measurement results.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2024

Evaluation of flow-induced plate deflection for University of Missouri research reactor low-enriched uranium fuel element

The University of Missouri Research Reactor (MURR), located on the campus of the University of Missouri in Columbia, Missouri, is one of the six United States (U.S.) High Performance Research Reactors (USHPRR), including one critical facility, that are actively collaborating with the U.S. Department of Energy (DOE) National Nuclear Security Administration (NNSA) Office of Material Management and Minimization (M3) Reactor Conversion Program to convert from highly enriched uranium (HEU, ≥20 wt% U-235) fuel to low-enriched uranium (LEU, <20 wt% U-235) fuel. A new type of very high-density LEU fuel based on a monolithic alloy of uranium and 10 wt% molybdenum (U-10Mo) is expected to allow conversion of some USHPRR, including MURR. In the design of its fuel elements, MURR is using thin parallel curved fuel plates separated by coolant channels. In this work, fluid-structure interaction (FSI) analysis of the MURR LEU fuel element is performed at the element level (as compared to the plate level analysis), which models all components of the LEU fuel element, including fuel plates and the supporting structures. Therefore, the effect of supporting structures on the flow distribution within the element and the fuel plate deflection are evaluated. In addition to the element nominal flow rate and dimensions, the tolerances in the geometry of the coolant channel and plate thickness, the effect of a comb on plate deflection, and the uncertainty of the flow rate per element are evaluated. For the LEU fuel plates, which are thinner than the current HEU plates, the predicted plate deflection is found to be small compared to the fabrication and assembly tolerances. Thus, the FSI-induced deflections are not expected to noticeably reduce the coolant flow rate or predicted safety margins in the limiting channels for the MURR LEU fuel element. In addition to the simulation work, a hydraulic performance test of the MURR LEU fuel element is currently being planned to support conversion to the use of LEU fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Poly(vinylferrocene) as an Ionomer and Sulfur-Confining Additive for Lithium–Sulfur Batteries

Lithium-sulfur (Li-S) batteries are promising owing to their high energy density, environmental benignity, and low cost. Most of the commonly used binders in Li-S battery cathodes are inert and have no significant effect on the challenges of sulfur as a cathode material, such as the polysulfide shuttle effect, low ionic/electronic conductivity, and a sluggish redox reaction. In this work, we demonstrate the use of poly(vinylferrocene) (PvFc) as a binder additive that can effectively increase the ionic conductivity of the cathode and act as a sulfide confining agent. Electrochemical tests performed with PvFc as part of the binder mixture used to cast the cathodes demonstrate an increase in rate capability and cycle life when compared to the baseline samples. Ionic conductivity measurements and X-ray photoelectron spectroscopy suggest that the π-cation molecular interaction between the cyclopentadienyl rings from ferrocene and Li + act like an ion couple with ferrocene acting as a static, covalently bound acceptor of Li + ions that enhances their mobility through the cathode. This coupled with the affinity between the ferrocenyl cations and the Li salt anions, which provides more distribution of counterions for Li + movement and improves accessibility to the cathode S reservoir, make PvFc a promising ionomer for Li-S batteries. In addition, the π-cation bonds between cyclopentadienyl and lithium polysulfides produce a sulfide confining effect that mitigates capacity fade through polysulfide dissolution. Furthermore, this work demonstrates an expansion in the utility of PvFc as a component in Li-ion batteries, which so far is mostly limited to use as an active material in organometallic batteries.

25 ENERGY STORAGE↗
DOE OSTI2023

Adaptive Pore Opening to Form Tailored Adsorption Sites in a Cooperatively Flexible Framework Enables Record Inverse Propane/Propylene Separation

A proposed low-energy alternative to the separation of alkanes from alkenes by energy-intensive cryogenic distillation is separation by porous adsorbents. Unfortunately, most adsorbents preferentially take up the desired, high-value major component alkene, requiring frequent regeneration. Adsorbents with inverse selectivity for the minor component alkane would enable the direct production of purified, reagent-grade alkene, greatly reducing global energy consumption. However, such materials are exceedingly rare, especially for propane/propylene separation. Here, we report that through adaptive and spontaneous pore size and shape adaptation to optimize an ensemble of weak noncovalent interactions, the structurally responsive metal-organic framework CdIF-13 (sod-Cd(benzimidazolate) 2 ) exhibits inverse selectivity for propane over propylene with record-setting separation performance under industrially relevant temperature, pressure, and mixture conditions. Powder synchrotron X-ray diffraction measurements combined with first-principles calculations yield atomic-scale insight and reveal the induced fit mechanism of adsorbate-specific pore adaptation and ensemble interactions between ligands and adsorbates. Dynamic column breakthrough measurements confirm that CdIF-13 displays selectivity under mixed-component conditions of varying ratios, with a record measured selectivity factor of α ≈ 3 at 95:5 propylene:propane at 298 K and 1 bar. When sequenced with a low-cost rigid adsorbent, we demonstrated the direct purification of propylene under ambient conditions. In conclusion, this combined atomic-level structural characterization and performance testing firmly establishes how cooperatively flexible materials can be capable of unprecedented separation factors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

The Green's Function Model Intercomparison Project (GFMIP) Protocol

The atmospheric Green's function method is a technique for modeling the response of the atmosphere to changes in the spatial field of surface temperature. While early studies applied this method to changes in atmospheric circulation, it has also become an important tool to understand changes in radiative feedbacks due to evolving patterns of warming, a phenomenon called the “pattern effect.” To better study this method, this paper presents a protocol for creating atmospheric Green's functions to serve as the basis for a model intercomparison project, GFMIP. The protocol has been developed using a series of sensitivity tests performed with the HadAM3 atmosphere-only general circulation model, along with existing and new simulations from other models. Our preliminary results have uncovered nonlinearities in the response of the atmosphere to surface temperature changes, including an asymmetrical response to warming versus cooling patch perturbations, and a change in the dependence of the response on the magnitude and size of the patches. These nonlinearities suggest that the pattern effect may depend on the heterogeneity of warming as well as its location. These experiments have also revealed tradeoffs in experimental design between patch size, perturbation strength, and the length of control and patch simulations. The protocol chosen on the basis of these experiments balances scientific utility with the simulation time and setup required by the Green's function approach. Running these simulations will further our understanding of many aspects of atmospheric response, from the pattern effect and radiative feedbacks to changes in circulation, cloudiness, and precipitation.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

The Effect of Hydrothermal Alteration and Microcracks on Hydraulic Properties and Poroelastic Deformation: A Case Study of the Blue Mountain Geothermal Field

Abstract Geothermal energy plays a vital role in decarbonizing electricity and heat supply. Effective utilization of geothermal resources hinges on identifying or generating permeable reservoir zones and understanding how effective pressure variations affect fluid circulation and reservoir properties by poroelastic deformation. Hydrothermal alteration can modify the petrophysical properties of geothermal reservoir rocks, which may increase or decrease its productivity. Understanding these alteration effects is essential to predict and optimize long‐term sustainable geothermal operations. Here, we investigate the impact of hydrothermal alteration on poroelastic and hydraulic properties of diverse lithologies in a series of deformation tests performed at several confining (0–80 MPa) and pore pressure (10–30 MPa) levels. Experimental results of hydrothermally altered dikes and phyllites obtained from the Blue Mountain geothermal field (Nevada, USA) are compared to thermally cracked La Peyratte granite (France) and correlated with petrophysical properties, mineral composition, and microstructures. Argillic alteration of dikes increases porosity and storage capacity but lowers thermal conductivity and increases pore compressibility. Conversely, silicate precipitation in phyllites increases stiffness and thermal conductivity but also reduces porosity and permeability. Experimentally determined effective pressure coefficients range from 0.1 to 0.9, differ for permeability and volumetric strain and decrease with increasing effective pressure. The presence of compliant microcracks and crack‐like pores significantly increases the stress sensitivity of La Peyratte granite and silicified phyllites. This study demonstrates how thermal and chemical alteration impacts poromechanical and petrophysical characteristics of geothermal targets, which ultimately govern reservoir stability and subsidence, induced seismicity as well as fluid and heat extraction efficiency during geothermal operations.

Schuster, Valerian [Helmholtz Centre Potsdam GFZ G↗
DOE OSTI2025

Accurate and uncertainty-aware multi-task prediction of HEA properties using prior-guided deep Gaussian processes

Surrogate modeling techniques have become indispensable in accelerating the discovery and optimization of high-entropy alloys (HEAs), especially when integrating computational predictions with sparse experimental observations. This study systematically evaluates the training and testing performance of four prominent surrogate models—conventional Gaussian processes (cGP), Deep Gaussian processes (DGP), encoder-decoder neural networks for multi-output regression and eXtreme Gradient Boosting (XGBoost)—applied to a hybrid dataset of experimental and computational properties of the 8-component HEA system Al-Co-Cr-Cu-Fe-Mn-Ni-V. We specifically assess their capabilities in predicting correlated material properties, including yield strength, hardness, modulus, ultimate tensile strength, elongation, and average hardness under dynamic/quasi-static conditions, alongside auxiliary computational properties. The comparison highlights the strengths of hierarchical deep modeling approaches in handling heteroscedastic, heterotopic, and incomplete data commonly encountered in materials science. Our findings illustrate that combined surrogate models such as DGPs infused with machine-learned priors outperform other surrogates by effectively capturing inter-property correlations and by assimilating prior knowledge. This enhanced predictive accuracy positions the combined surrogate models as powerful tools for robust and data-efficient materials design.

36 MATERIALS SCIENCE↗
DOE OSTI2022

The effect of differential mineral shrinkage on crack formation and network geometry

Rock, concrete, and other engineered materials are often composed of several minerals that change volumetrically in response to variations in the moisture content of the local environment. Such differential shrinkage is caused by varying shrinkage rates between mineral compositions during dehydration. Using both 3D X-ray imaging of geo-architected samples and peridynamic (PD) numerical simulations, we show that the spatial distribution of the clay affects the crack network geometry with distributed clay particles yielding the most complex crack networks and percent damage (99.56%), along with a 60% reduction in material strength. We also demonstrate that crack formation, growth, coalescence, and distribution during dehydration, are controlled by the differential shrinkage rates between a highly shrinkable clay and a homogeneous mortar matrix. Sensitivity tests performed with the PD models show a clay shrinkage parameter of 0.4 yields considerable damage, and reductions in the parameter can result in a significant reduction in fracturing and an increase in material strength. Additionally, isolated clay inclusions induced localized fracturing predominantly due to debonding between the clay and matrix. These insights indicate differential shrinkage is a source of potential failure in natural and engineered barriers used to sequester anthropogenic waste.

58 GEOSCIENCES↗
DOE OSTI2024

Radiation-induced alteration of apatite on the surface of Mars: first in situ observations with SuperCam Raman onboard Perseverance

Abstract Planetary exploration relies considerably on mineral characterization to advance our understanding of the solar system, the planets and their evolution. Thus, we must understand past and present processes that can alter materials exposed on the surface, affecting space mission data. Here, we analyze the first dataset monitoring the evolution of a known mineral target in situ on the Martian surface, brought there as a SuperCam calibration target onboard the Perseverance rover. We used Raman spectroscopy to monitor the crystalline state of a synthetic apatite sample over the first 950 Martian days (sols) of the Mars2020 mission. We note significant variations in the Raman spectra acquired on this target, specifically a decrease in the relative contribution of the Raman signal to the total signal. These observations are consistent with the results of a UV-irradiation test performed in the laboratory under conditions mimicking ambient Martian conditions. We conclude that the observed evolution reflects an alteration of the material, specifically the creation of electronic defects, due to its exposure to the Martian environment and, in particular, UV irradiation. This ongoing process of alteration of the Martian surface needs to be taken into account for mineralogical space mission data analysis.

Science & Technology - Other Topics↗
DOE OSTI2021

Enhancing the inherent catalytic activity and stability of TiO 2 supported Pt single-atoms at CeO x –TiO 2 interfaces

Single-atoms (SAs) with atomically coordinated reaction centers are considered the next generation of catalysts that can exhibit exceptional catalytic efficiency. However, the general concern about thermodynamic vulnerabilities of SAs questions their practical value. Moreover, whether the inherent catalytic nature of SAs is superior compared with that of larger nanoparticles is still under debate. Here, we address two controversies by a comparative study using two catalysts: Pt/TiO 2 and Pt/CeO x –TiO 2 . Based on a hierarchical study of density functional theory, time-resolved catalysis performance test, in situ infrared spectroscopy, and operando X-ray absorption spectroscopy, we could unveil the catalytic nature of Pt-SAs and their stability. By utilizing the heterogeneous interface formed between TiO 2 supporting particles and CeO x clusters formed on the surface of TiO 2 , we preferentially synthesized Pt-SAs pinned at the CeO x –TiO 2 interfaces on CeO x –TiO 2 hybrid-oxide supports. The strong electronic coupling between the Pt-SAs and the Ce ions at the CeO x –TiO 2 interfaces enhanced the catalytic activity toward CO oxidation of Pt-SAs and improved the long-term stability under CO oxidation conditions. The CO oxidation activity of Pt-SAs stabilized at CeO x –TiO 2 was improved by 13.5 times at 200 °C compared with the Pt-SAs on TiO 2 . The results present how to easily improve the activity and stability of Pt-SAs using a simple interface control method. Moreover, we demonstrate that the catalytic activity and the stability of Pt-SAs can be monitored through the chemical state of the interfaces. Finally, our study provides comprehensive understanding about the catalytic nature as well as a novel strategy toward applications of Pt-SAs, enabling sustainable use of Pt in heterogeneous catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

One-step fabrication of robust lithium ion battery separators by polymerization-induced phase separation

Conventional lithium ion battery separators are microporous polyolefin membranes that play a passive role in the electrochemical cell. Next generation separators should offer significant performance enhancements, while being fabricated through facile, low cost approaches with the ability to readily tune physicochemical properties. This study presents a single-step manufacturing technique based on UV-initiated polymerization-induced phase separation (PIPS), wherein microporous separators are fabricated from multifunctional monomers and ethylene carbonate (EC), which functions as both the pore-forming agent (porogen) and electrolyte component in the electrochemical cell. By controlling the ratio of the 1,4-butanediol diacrylate (BDDA) monomer to ethylene carbonate, monolithic microporous membranes are readily prepared with 25 μm thickness and pore sizes and porosities ranging from 6.8 to 22 nm and 15.4% to 38.5%, respectively. With 38.5% apparent porosity and an average pore size of 22 nm, the poly(1,4-butanediol diacrylate) (pBDDA) separator takes up 127% liquid electrolyte, resulting in an ionic conductivity of 1.98 mS cm –1 , which is greater than in conventional Celgard 2500. Lithium ion battery half cells consisting of LiNi 0.5 Mn 0.3 Co 0.2 O 2 cathodes and pBDDA separators were shown to undergo reversible charge/discharge cycling with an average discharge capacity of 142 mA h g –1 and a capacity retention of 98.4% over 100 cycles – comparable to cells using state-of-the-art separators. Moreover, similar discharge capacities were achieved in rate performance tests due to the high ionic conductivity and electrolyte uptake of the film. Finally, the pBDDA separators were shown to be thermally stable to 374 °C, lack low temperature thermal transitions that can compromise cell safety, and exhibit no thermal shrinkage up to 150 °C.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Implementation of a Talbot–Lau x-ray deflectometer diagnostic platform for the OMEGA EP laser

A Talbot–Lau X-ray Deflectometer (TXD) was implemented in the OMEGA EP laser facility to characterize the evolution of an irradiated foil ablation front by mapping electron densities >10 22 cm -3 by means of Moiré deflectometry. The experiment used a short-pulse laser (30–100 J, 10 ps) and a foil copper target as an x-ray backlighter source. In the first experimental tests performed to benchmark the diagnostic platform, grating survival was demonstrated and x-ray backlighter laser parameters that deliver Moiré images were described. Finally, the necessary modifications to accurately probe the ablation front through TXD using the EP-TXD diagnostic platform are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Flexible machine-learning interatomic potential for simulating structural disordering behavior of Li 7 La 3 Zr 2 O 12 solid electrolytes

Batteries based on solid-state electrolytes, including Li 7 La 3 Zr 2 O 12 (LLZO), promise improved safety and increased energy density; however, atomic disorder at grain boundaries and phase boundaries can severely deteriorate their performance. Machine-learning (ML) interatomic potentials offer a uniquely compelling solution for simulating chemical processes, rare events, and phase transitions associated with these complex interfaces by mixing high scalability with quantum-level accuracy, provided that they can be trained to properly address atomic disorder. To this end, we report the construction and validation of an ML potential that is specifically designed to simulate crystalline, disordered, and amorphous LLZO systems across a wide range of conditions. The ML model is based on a neural network algorithm and is trained using ab initio data. Performance tests prove that the developed ML potential can predict accurate structural and vibrational characteristics, elastic properties, and Li diffusivity of LLZO comparable to ab initio simulations. As a demonstration of its applicability to larger systems, we show that the potential can correctly capture grain boundary effects on diffusivity, as well as the thermal transition behavior of LLZO. Here these examples show that the ML potential enables simulations of transitions between well-defined and disordered structures with quantum-level accuracy at speeds thousands of times faster than ab initio methods.

25 ENERGY STORAGE↗