Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “specific surface area”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 361 records · Page 20
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Solar concentrator technology development for space based applications, volume 2

Thermoelectric conversion using a radio-isotope heat source has been used where outer planetary space craft are too far away for absorbing significant solar energy. Solar dynamic power (SDP) conversion is one technology that offers advantages for applications within the inner planet region. Since SDP conversion efficiency can be 2 to 3 times higher than photovoltaic, the collecting surfaces are much reduced in area and therefore lighter. This becomes an advantage in allocating more weight to launched payloads. A second advantage results for low earth orbit applications. The reduced area results in lower drag forces on the spacecraft and requires less reboost propellant to maintain orbit. A third advantage occurs because of the sun-to-shade cycling while in earth orbit. Photovoltaic systems require batteries to store energy for use when in the shade, and battery life for periods of 10 to 15 years is not presently achievable. For these reasons the Solar Dynamics and Thermal Systems Branch at NASA LeRC has funded work in developing SDP systems. The generic SDP system uses a large parabolic solar concentrator to focus solar energy onto a power conversion device. The concentrators are large areas and must therefore be efficient and have low specific weights. Yet these surfaces must be precise and capable of being stowed in a launch vehicle and then deployed and sometimes unfurled in space. There are significant technical challenges in engineering such structures, and considerable investigation has been made to date. This is the second of two volumes reporting on the research done by the Advanced Manufacturing Center at Cleveland State University to assist NASA LeRC in evaluating this technology. This volume includes the appendices of selected data sets, drawings, and procedures. The objective of the grant was to restore the solar concentrator development technology of the 1960s while improving it with advances that have occurred since then. This report summarizes the work done from January 1989 through December 1991.

Pintz, A.↗
DOE OSTI2023

Advanced Modeling and Simulation to Characterize Advanced Boiling Water Reactor Source Terms to Support a Regulatory Approval Pathway for Right-Sized Emergency Planning Zone. Advanced Boiling Water Reactor (A-BWR) Project Phase 2

The United States Department of Energy (US DOE) is currently supporting the development of various small modular reactor (SMR), microreactor and advanced reactor designs. These reactors have improved safety features as compared to conventional Large Light Water Reactors (LLWRs), which include features that improve potential reduction of radiological source terms in the event of design and beyond-design basis accidents. Specifically, some reactors feature a relatively smaller containment volume with respect to the available surface area for fission product deposition; these include Integrated Pressurized Water Reactors (iPWRs), such as the NuScale SMR and SMR-type Boiling Water Reactors (BWRs) such as General Electric-Hitachi’s BWRX-300 design.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
NASA NTRS1983

Perfect bell nozzle parametric and optimization curves

Nozzle contour data for untruncated Bell nozzles with expansion area ratios to 6100 and a specific heat ratio of 1.2 are provided. Curves for optimization of nozzles for maximum thrust coefficient within a given length, surface area, or area ratio are included. The nozzles are two dimensional axisymmetric and calculations were performed using the method of characteristics. Drag due to wall friction was included in the final thrust coefficient.

Tuttle, J. L.↗
DOE OSTI2021

Self-Anchored Platinum-Decorated Antimony-Doped-Tin Oxide as a Durable Oxygen Reduction Electrocatalyst

The lifetime of commercial Proton Exchange Membrane Fuel Cells (PEMFCs) is circumscribed by the insufficient durability of commercial catalysts. The use of metal oxide supports in place of carbon significantly increases electrocatalyst durability. Herein, following density functional theory (DFT) predictions of improved Platinum (Pt) stability on antimony doped tin oxide (ATO) supports, we synthesized ATO whose morphology and crystal structure was engineered using a Pt anchoring technique. X-ray photoelectron spectroscopy (XPS) indicated that the Pt anchor sites aided in the reduction of Pt precursors to Pt on the ATO surface. X-ray absorption near-edge spectroscopy (XANES) revealed the existence of strong-metal-support interactions (SMSI) between Pt and ATO. The combination of SMSI and high control over Pt dispersion enabled the Pt/Pt-aerogel-ATO (Pt supported on aerogel ATO with Pt anchor sites) electrocatalyst to achieve 2x the area specific activity of Pt/C in ex-situ testing. In a H 2 /air PEMFC Pt/Pt-aerogel-ATO cathodes enabled 20% higher peak power density and <1/6 the loss of active surface area as compared to Pt/C. Notably, in a PEMFC under rigorous potential cycling, the Pt/Pt-aerogel-ATO retained its initial peak power density as opposed to a 58% loss for Pt/C. Further, cost models indicate that Pt/Pt-aerogel-ATO is 26% less expensive than Pt/C over its useful lifetime.

25 ENERGY STORAGE↗
DOE OSTI2022

Thermal Management System for an Electric Machine with Additively Manufactured Hollow Conductors with Integrated Heat Pipes: Preprint

This paper discusses steps taken to size a thermal management system for an aircraft propulsion electric machine containing additively manufactured coils integrated with heat pipes aimed at boosting its specific power. Experimental setups are used to size and characterize heat pipes for the application and 3D thermal FEA is used to determine optimum heat transfer coefficient of convective boundaries. Geometric details of fin-based surface area enhancement required to reach target combined overall heat transfer coefficient (U) and surface area (A) performance (UA) in W/K, is worked out for relevant boundaries and the resulting UA is verified in 3D thermal FEA. Thermal management system's UA (by extension specific power) sensitivity to coolant temperature is explored and temperature distribution plots of optimized machine components are presented and discussed.

additive manufacturing↗
NASA NTRS1997

Airport Surface Delays and Causes: A Preliminary Analysis

This report summarizes FAA Program Analysis and Operations Research Service (ASD-400)/Lockheed Martin activities and findings related to airport surface delays and causes, in support of NASA Langley Research Center's Terminal Area Productivity (TAP) Program. The activities described in this report were initiated in June 1995. A preliminary report was published on September 30, 1995. The final report incorporates data collection forms filled out by traffic managers, other FAA staff, and an airline for the New York City area, some updates, data previously requested from various sources to support this analysis, and further quantification and documentation than in the preliminary report. This final report is based on data available as of April 12, 1996. This report incorporates data obtained from review and analysis of data bases and literature, discussions/interviews with engineers, air-traffic staff, other FAA technical personnel, and airline staff, site visits, and a survey on surface delays and causes. It includes analysis of delay statistics; preliminary findings and conclusions on surface movement, surface delay sources and causes, runway occupancy time (ROT), and airport characteristics impacting surface operations and delays; and site-specific data on the New York City area airports, which are the focus airports for this report.

Chin, David K.↗
DOE OSTI2025

Impact of Urbanization on Convection, Lightning, and Precipitation Over the Houston Metropolitan Area: Case Study Simulation From the TRACER Campaign

This study investigates the effects of urbanization, specifically land use change and anthropogenic emissions (AE), on convection, lightning, and surface precipitation for a case of summertime sea‐breeze convection observed over the Houston metropolitan area. The unique capabilities of the NASA‐Unified Weather Research and Forecasting model allows us to conduct a series of sensitivity experiments with complex configurations, in particular including multi‐year land model spin‐up simulations, treatment of aerosols and their precursors, and explicit cloud charging and lightning. The simulation results show that urban land use primarily alters the temporal evolution of convection, lightning, and surface precipitation, leading to late afternoon thunderstorm development. The decrease in latent heat flux from the land surface caused by urbanization weakens convection in the early afternoon, while a condition suitable for convection development is maintained in the late afternoon due to less stabilization of the lower troposphere by the weaker convection development and high sensible heat flux from the surface. On the other hand, anthropogenic aerosols directly enhance convection, lightning, and surface precipitation by increasing convective updrafts due to the aerosol‐induced convective invigoration. The combined effects of urban land use and AE lead to even stronger thunderstorms in the late afternoon, mostly consistent with observations. These results indicate that urbanization increases the probability of late afternoon thunderstorms over the Houston area during the summer season. Advanced weather forecasting models that incorporate these urbanization effects might support sustainable urban planning to better mitigate the impacts of urbanization on local weather and public safety.

Iguchi, T. [Univ. of Maryland, College Park, MD (U↗
DOE OSTI2024

A high-performance intermediate temperature reversible solid oxide cell with a new barrier layer free oxygen electrode

The best solution to address the critical durability issue of solid oxide electrolytic cells (SOECs) for high-efficiency and high-rate H 2 production is to lower the operating temperature without sacrificing the performance. Developing high performance oxygen electrodes (OEs) is a key to capitalizing this solution. Here, in this paper, we report on a highly active OE for intermediate temperature ZrO 2 -based SOECs without a CeO 2 barrier layer. The new barrier-layer-free (BLF) OE is a composite of two materials, (Bi 0.75 Y 0.25 ) 0.93 Ce 0.07 O 1.5±δ (BYC) that exhibits high oxide-ion conductivity and La 0.8 Sr 0.2 MnO 3 (LSM) that possesses a high electronic conductivity to enable fast oxygen reduction/evolution reactions (ORR/OER). Featuring a microscale porous BYC scaffold decorated with high surface area LSM nanoparticles (NPs), the new BLF-OE exhibited a low area specific resistance (ASR) of 0.10 Ω cm 2 at 650 °C in air. With 50%H 2 -50%H 2 O as a feed to hydrogen electrode (HE) and air to OE, the single cell performance achieved 588 mA cm -2 at 0.80 V in the fuel cell mode and 688 mA cm -2 at 1.30 V in the electrolytic mode at 650 °C. Our in-house testing showed that this level of performance was ~3.5x higher than the cell with the benchmark La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-δ -Ce 0.9 Gd 0.1 O 2-δ OE. The long-term durability testing under alternating fuel cell and electrolytic modes showed a low degradation rate of 0.10 mA cm -2 h -1 over 550 hours. These encouraging results showed the great promise of the newly developed BYC-LSM to be an excellent OE candidate for intermediate temperature SOECs.

25 ENERGY STORAGE↗
DOE OSTI2026

Binder-Stabilized Carbon Fiber Hosts for High-Utilization Sodium–Polysulfide Flow Catholytes

Sodium-sulfur (Na-S) batteries hold promise as high-energy-density batteries for long-duration energy storage due to their high open circuit voltage and Earth-abundant active materials. However, low utilization of the sulfur active material limits the achievable specific capacity, especially when a liquid polysulfide catholyte is utilized. High-surface-area carbon materials demonstrate promise to increase sulfur utilization in a Na-S battery. To make the carbon host material applicable for a flow battery application, a binder is required to bind the carbon materials together and to a porous substrate. Here, we utilize a composite carbon paper electrode coated by polymer,carbon nanofibers (CNFs) and carbon black (CB). By varying the mass ratios of CNF to CB, we found that a 70/20/10 mass ratio of CNF/CB/binder provided the highest capacity (260 mAh g −1 compared to the baseline of 156 mAh g −1 ) and stable battery performance over 100 cycles. Analysis of the composite electrode and full cells reveals that the amount of CB in the composite electrode influences binder distribution, cell resistance, and full cell performance.

Lehmann, Michelle L. [Oak Ridge National Laborator↗
NASA NTRS1990

Lead-ruthenium pyrochlores as oxygen electrocatalysts

An investigation of lead-ruthenium pyrochlores of the structure Pb2(Ru/2-x/Pb/x/) O7-y for use as oxygen electrocatalysts in alkaline media is discussed. Lead-ruthenium pyrochlore mixed metal oxides were prepared and characterized by X-ray diffraction, BET surface area, dry powder conductivity, and chemical stability. Gas diffusion electrodes were developed specifically for the lead-ruthenium pyrochlore materials. Also investigated were the effects of varying electrode fabrication parameters on the oxygen reduction performance of the lead-ruthenium pyrochlore electrocatalyst. Long-term stability performance was also evaluated. The oxygen reduction performance of the pyrochlore electrocatalyst is considerably higher than that of the state-of-the-art gold-platinum alloy electrocatalyst currently used by NASA. Furthermore, the pyrochlore electrocatalysts are attractive candidates for high-performance pressurized alkaline fuel cells.

Anderson, E. B.↗
NASA NTRS1999

Impact of Assimilating GOES-Derived Land Surface Variables into the PSU/NCAR MM5

Land surface processes are known to have a profound impact on the overlying atmosphere over a wide range of spatial and temporal scales. Many atmospheric numerical models include special parameterizations to improve the specification and partitioning of surface fluxes which are critical to the accurate prediction of warm season boundary layer behavior, organized mesoscale circulations, and convective precipitation. However, the added degrees of freedom resulting from the inclusion of vegetation and soil schemes require the specification of additional surface parameters such as vegetative resistances, green vegetation fraction, leaf area index, soil physical and hydraulic characteristics, and the vertical distribution of soil moisture. As satellite data have become more readily available in recent years, many investigations have attempted to use these new measurements to infer missing components of the surface energy budget. Sensitivity studies have shown land-skin temperature (LST) tendencies during the mid-morning hours are strongly sensitive to the surface moisture availability (a function of soil wetness and vegetation) and less sensitive to other parameters such as surface roughness. Based upon results from these and other studies, developed a simple technique that dynamically assimilates Geostationary Operational Environmental Satellite (GOES) derived land-surface products into the surface energy budget of a mesoscale model. The purpose of this paper is to demonstrate that assimilating the GOES satellite data has the potential to improve the representation of land surface characteristics within the model without prior knowledge of the land surface characteristics. The assimilation technique is presented in Section 2 and the numerical experiments are detailed in Section 3. Preliminary results and conclusions are presented in Sections 4 and 5, respectively.

Lapenta, William M.↗
NASA NTRS2003

Effect of Alignment on Transport Properties of Carbon Nanotube/Metallic Junctions

Ballistic and spin coherent transport in single walled carbon nanotubes (SWCNT) are predicted to enable high sensitivity single-nanotube devices for strain and magnetic field sensing. Based upon these phenomena, electron beam lithography procedures have been developed to study the transport properties of purified HiPCO single walled carbon nanotubes for development into sensory materials for nondestructive evaluation. Purified nanotubes are dispersed in solvent suspension and then deposited on the device substrate before metallic contacts are defined and deposited through electron beam lithography. This procedure produces randomly dispersed ropes, typically 2 - 20 nm in diameter, of single walled carbon nanotubes. Transport and scanning probe microscopy studies have shown a good correlation between the junction resistance and tube density, alignment, and contact quality. In order to improve transport properties of the junctions a technique has been developed to align and concentrate nanotubes at specific locations on the substrate surface. Lithographic techniques are used to define local areas where high frequency electric fields are to be concentrated. Application of the fields while the substrate is exposed to nanotube-containing solution results in nanotube arrays aligned with the electric field lines. A second electron beam lithography layer is then used to deposit metallic contacts across the aligned tubes. Experimental measurements are presented showing the increased tube alignment and improvement in the transport properties of the junctions.

Wincheski, Buzz↗
NASA NTRS2011

Fischer-Tropsch Catalyst for Aviation Fuel Production

As the oil supply declines, there is a greater need for cleaner alternative fuels. There will undoubtedly be a shift from crude oil to non-petroleum sources as a feedstock for aviation (and other transportation) fuels. The Fischer-Tropsch process uses a gas mixture of carbon monoxide and hydrogen which is converted into various liquid hydrocarbons; this versatile gas-to-liquid technology produces a complex product stream of paraffins, olefins, and oxygenated compounds such as alcohols and aldehydes. The Fischer-Tropsch process can produce a cleaner diesel oil fraction with a high cetane number (typically above 70) without any sulfur and aromatic compounds. It is most commonly catalyzed by cobalt supported on alumina, silica, or titania or unsupported alloyed iron powders. Cobalt is typically used more often than iron, in that cobalt is a longer-active catalyst, has lower water-gas shift activity, and lower yield of modified products. Promoters are valuable in improving Fischer-Tropsch catalyst as they can increase cobalt oxide dispersion, enhance the reduction of cobalt oxide to the active metal phase, stabilize a high metal surface area, and improve mechanical properties. Our goal is to build up the specificity of the Fischer-Tropsch catalyst while adding less-costly transition metals as promoters; the more common promoters used in Fischer-Tropsch synthesis are rhenium, platinum, and ruthenium. In this report we will describe our preliminary efforts to design and produce catalyst materials to achieve our goal of preferentially producing C8 to C18 paraffin compounds in the NASA Glenn Research Center Gas-To-Liquid processing plant. Efforts at NASA Glenn Research Center for producing green fuels using non-petroleum feedstocks support both the Sub-sonic Fixed Wing program of Fundamental Aeronautics and the In Situ Resource Utilization program of the Exploration Technology Development and Demonstration program.

deLaRee, Ana B.↗
NASA NTRS2012

Fischer-Tropsch Catalyst for Aviation Fuel Production

As the oil supply declines, there is a greater need for cleaner alternative fuels. There will undoubtedly be a shift from crude oil to nonpetroleum sources as a feedstock for aviation (and other transportation) fuels. The Fischer-Tropsch process uses a gas mixture of carbon monoxide and hydrogen which is converted into various liquid hydrocarbons; this versatile gas-to-liquid technology produces a complex product stream of paraffins, olefins, and oxygenated compounds such as alcohols and aldehydes. The Fischer-Tropsch process can produce a cleaner diesel oil fraction with a high cetane number (typically above 70) without any sulfur and aromatic compounds. It is most commonly catalyzed by cobalt supported on alumina, silica, or titania or unsupported alloyed iron powders. Cobalt is typically used more often than iron, in that cobalt is a longer-active catalyst, has lower water-gas shift activity, and lower yield of modified products. Promoters are valuable in improving Fischer-Tropsch catalyst as they can increase cobalt oxide dispersion, enhance the reduction of cobalt oxide to the active metal phase, stabilize a high metal surface area, and improve mechanical properties. Our goal is to build up the specificity of the Fischer-Tropsch catalyst while adding less-costly transition metals as promoters; the more common promoters used in Fischer-Tropsch synthesis are rhenium, platinum, and ruthenium. In this report we will describe our preliminary efforts to design and produce catalyst materials to achieve our goal of preferentially producing C8 to C18 paraffin compounds in the NASA Glenn Research Center Gas-To-Liquid processing plant. Efforts at NASA Glenn Research Center for producing green fuels using non-petroleum feedstocks support both the Sub-sonic Fixed Wing program of Fundamental Aeronautics and the In Situ Resource Utilization program of the Exploration Technology Development and Demonstration program.

DeLaRee, Ana B.↗
NASA NTRS2016

Asteroid Redirect Mission (ARM) Formulation Assessment and Support Team (FAST) Final Report

The Asteroid Redirect Mission (ARM) Formulation Assessment and Support Team (FAST) was a two-month effort, chartered by NASA, to provide timely inputs for mission requirement formulation in support of the Asteroid Redirect Robotic Mission (ARRM) Requirements Closure Technical Interchange Meeting held December 15-16, 2015, to assist in developing an initial list of potential mission investigations, and to provide input on potential hosted payloads and partnerships. The FAST explored several aspects of potential science benefits and knowledge gain from the ARM. Expertise from the science, engineering, and technology communities was represented in exploring lines of inquiry related to key characteristics of the ARRM reference target asteroid (2008 EV5) for engineering design purposes. Specific areas of interest included target origin, spatial distribution and size of boulders, surface geotechnical properties, boulder physical properties, and considerations for boulder handling, crew safety, and containment. In order to increase knowledge gain potential from the mission, opportunities for partnerships and accompanying payloads were also investigated. Potential investigations could be conducted to reduce mission risks and increase knowledge return in the areas of science, planetary defense, asteroid resources and in-situ resource utilization, and capability and technology demonstrations. This report represents the FASTâ€"TM"s final product for the ARM.

Mazanek, Daniel D.↗
DOE OSTI2020

Source Term Reduction for Advanced and Small Modular Boiling Water Reactors

The United States Department of Energy (US DOE) is currently supporting the development of various advanced and small modular reactor (SMR) designs. Several of these designs have commenced license application with the US Nuclear Regulatory Commission (US NRC). These reactors have improved safety features that may significantly reduce radiological source terms in the event of design and beyond-design basis accidents. Specifically, some reactors feature a smaller containment volume relative to the available fission product depositional surface area, which supports increased fission product retention in the containment vessel. Pressurized water reactors (PWR) and boiling water reactors (BWR) with this feature include the integral pressurized water reactor (iPWR) and the BWRX-300 design by General Electric. A prior research program supported by the US DOE quantified the source term reduction associated with light water iPWRs and developed iPWR-specific theoretical models for fission product deposition rates. This program included a sequence of research projects that started with a feasibility study, development of theoretical models that predict higher deposition rates, and finally, development of empirical data for verification and validation of the theoretical models. The current project, which is a feasibility study, is the first step in a similar program to quantify the source term reduction associated with small and advanced light water BWRs.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRSDate not supplied

A Multiphysics Study to Improve Specific Energy of Primary Batteries for Low Temperature Operation for Deep Space Missions

Several lander missions on the outer planets such as Europa, Enceladus, and Titan require electrical power to operate scientific and communication equipment. The traditional power generation methods, such as a photovoltaic array, are not feasible as their efficiency drops significantly at these vast distances. The novel radioisotope power systems are not practical today based on current lander designs and the effectiveness of these systems. To perform in situ science on distant planets, a high specific energy battery (>700 Wh/kg) needs to operate for about 480 hours under cold temperatures (-40C or 0C) [1]. While a primary battery such as Li-CFx can provide high specific energy at room temperature, its specific capacity decreases significantly at low temperatures. One of the causes for this drop is low ion and electrical conductivity, and slower reaction kinetics. Slower transport and facile kinetics lead to an increase in the battery’s resistance and higher voltage drops during the cell operation, thus reducing specific capacity. Both the transport and kinetics show a strong dependence on temperature. Thus, a small temperature rise can lead to an increase in the reaction rate and ion conductivity; since the temperature, cell resistance, and specific capacity are interdependent. A conventional battery model accounts for ohmic, thermodynamic, and, electrochemical, and chemical decomposition heating. The ohmic heating can be controlled by designing a resistive microstructure and varying the ratios of the active materials [2]. The kinetics can be improved by increasing the surface area, reducing the particle size, or adding a catalyst. These parameters are often optimized to achieve high specific energy at room temperatures. A similar optimization study is not available at low temperatures and for a primary (high specific energy) battery. For this presentation, we will explore the effect of geometrical, microstructural, and material properties on optimal specific capacity at low temperatures through multiphysics simulations. The ion transport resistance depends on the porosity and the tortuosity of an electrode and the separator.

M. Mehta↗
DOE OSTI2021

Understanding the Role of π-Conjugated Polymers as Binders in Enabling Designs for High-Energy/High-Rate Lithium Metal Batteries

Developing lithium-ion batteries with both high specific energy and high-power capability is a challenging task because of the necessity for meeting conflicting design requirements. We show that high-energy and high-rate capability can be achieved by using various π -conjugated p-dopable polymers as binders at the cathode and by lowering the mass fraction of all the inactive components of the cell. We report a lithium-metal battery that can deliver 320 Wh kg −1 at C/2 using a mass-efficient cell design. To this end, three conducting polymers with different ionic and electronic conductivities have been studied; dihexyl-substituted poly(3,4-propylenedioxythiophene) (PProDOT-Hx 2 ), poly(3-hexylthiophene) (P3HT), and a new Random Copolymer (Hex:OE)(80:20) PProDOT. These conducting polymers are compared against a conventional polymer binder, PVDF. We show that under the mass-efficient conditions required for achieving high specific energy and rate capability, the conducting polymers play a crucial role by providing electronic and ionic conductivity, protection against rapid growth of solid electrolyte interphase (SEI), and access to a large electrochemically active surface area. Thus, the use of conducting polymers with appropriate molecular structure as binders opens a viable pathway to maximizing the specific energy and rate capability of lithium-ion battery cathodes.

25 ENERGY STORAGE↗