Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “yield point”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS2009

Flowability of JSC-1a

We have done a complete flowability characterization of the lunar soil simulant, JSC-1a, following closely the ASTM-6773 standard for the Schulze ring shear test. The measurements, which involve pre-shearing the material before each yield point, show JSC-1a to be cohesionless, with an angle of internal friction near 40 deg. We also measured yield loci after consolidating the material in a vibration table which show it to have significant cohesion (approximately equal to 1 kPa) and an angle of internal friction of about 60 deg. Hopper designs based on each type of flowability test differ significantly. These differences highlight the need to discern the condition of the lunar soil in the specific process where flowability is an issue. We close with a list not necessarily comprehensive of engineering rules of thumb that apply to powder flow in hoppers.

Rame, Enrique↗
NASA NTRS1996

The Influence of C and Si on the Flow Behavior of NiAl Single Crystals

Alloys based on the intermetallic compound NiAl are considered potential replacements for Ni and Co-based superalloys in high temperature structural applications due to their excellent oxidation resistance, low densities, high thermal conductivities, and increased melting points. Unfortunately, NiAl exhibits low tensile ductility at room temperature and low strengths at elevated temperatures which have combined to hinder its development. Recent efforts, have revealed that NiAl in the presence of sufficient solute levels, is subject to the phenomenon of strain aging which manifests itself as: sharp yield points, abnormally low strain rate sensitivities (SRS), plateaus or peaks in yield stress and work hardening rate as a function of temperature, flow stress transients upon an upward change in strain rate, reduced tensile elongations at elevated temperatures, and serrated stress-strain curves. Though recent efforts via either alloying or the removal of interstitial impurities, have resulted in consistent room-temperature tensile elongations exceeding 5% and the elimination of serrated flow, the effects of particular substitutional and interstitial elements and the mechanisms by which they might enhance or hinder the mechanical properties remain unknown. Consequently, the purpose of the present paper is to provide a preliminary assessment of the influence of common substitutional and interstitial impurities on the deformation behavior of NiAl. To accomplish this goal a series of NiAl single crystal alloys containing various interstitial solutes were prepared and their mechanical properties were evaluated between 77 and 1100 K. Because Si is a common impurity in conventional purity single crystals grown by the Bridgman method, Si concentrations were also varied in order to determine the influence of this element.

Weaver, M. L.↗
NASA NTRS1975

Rate and time dependent failure of structural adhesives

Studies on two adhesives (Metlbond 1113 and 1113-2) identified as having important applications in the bonding of composite materials are presented. A testing program to ascertain stress-strain, strain-rate, time, yield, and/or failure behavior of these materials in bulk form using uniaxial tensile constant strain-rate, creep, and relaxation tests is described. The stress-strain behavior of each material is shown to be significantly rate dependent. A rate dependent stress whitening (crazing) phenomenon occurs prior to either yield or fracture. A region of linear elasticity, a region of viscoelasticity, and the onset of yielding are identified in the stress-strain behavior. The linear elastic limit and the yield point are shown to be rate dependent and agree well with an empirical equation proposed by Ludwik. A creep to failure phenomenon is shown to exist and is correlated with a delayed yield equation proposed by Crochet. Analytical predictions based on a modified Bingham model are shown to agree well with experimental stress-strain strain-rate data. Analytical predictions based on a modified Ramberg-Osgood equation are also shown for comparison purposes.

Brinson, H. F.↗
DOE OSTI2026

Long-term thermal stability and calibration of Type-II fiber Bragg grating array inscribed in radiation-hardened fibers

This paper investigates the long-term thermal stability of Type-II fiber Bragg grating (FBG) arrays, inscribed by femtosecond laser in radiation-hardened fiber, for potential applications as multiplexed sensors in high-temperature energy systems. The thermal stability of FBG sensors was assessed through 16 thermal cycles from room temperature (RT) to 750 ℃ about two months, involving 100 FBG sensors. The results show that the absolute temperature drift of FBG sensors can be reduced to less than 0.4 pm/day after 54 h thermal annealing process at a constant temperature of 800 ℃. As temperature sensors, the FBGs demonstrated stable performance, achieving a standard deviation (STD) of 1.8 pm (corresponding to a temperature resolution of 0.118 ℃) post-annealing. Repeated thermal cycles revealed a random drift of 2.3 pm in the FBG wavelength at RT. Polynomial fitting was explored as a calibration method to convert FBG wavelength shifts into absolute temperature measurements. By optimizing calibration temperature points (RT, 200 ℃, 400 ℃, and 750 ℃), the study shows that cubic polynomial calibration using four points yields an average R2 of 0.9997 and an RMSE of 3.58 ℃ across the entire temperature range (RT to 750 ℃). This approach represents an 11.53-fold improvement over empirical slope calibration and a 1.34-fold improvement over four-point piecewise fitting. The findings indicate that Type-II FBGs inscribed in radiation-hardened fibers can function as accurate temperature sensors, with performance on par with or exceeding that of thermocouples. With their multiplexing capability, robust signal transmission over long lead cables, and immunity to electromagnetic interference, FBG sensors offer a promising alternative to traditional electronic sensors for energy system monitoring.

Dominguez-Ontiveros, Elvis [ORNL] (ORCID:000000018↗
DOE OSTI2020

Deformation of Lie–Poisson algebras and chirality

Linearization of a Hamiltonian system around an equilibrium point yields a set of Hamiltonian symmetric spectra: If λ is an eigenvalue of the linearized generator, -λ and $\barλ$ (hence, -$\barλ$) are also eigenvalues—the former implies a time-reversal symmetry, while the latter guarantees the reality of the solution. However, linearization around a singular equilibrium point (which commonly exists in noncanonical Hamiltonian systems) works out differently, resulting in breaking of the Hamiltonian symmetry of spectra; time-reversal asymmetry causes chirality. This interesting phenomenon was first found in analyzing the chiral motion of the rattleback, a boat-shaped top having misaligned axes of inertia and geometry [Z. Yoshida et al., Phys. Lett. A 381, 2772–2777 (2017)]. To elucidate how chiral spectra are generated, we study the three-dimensional Lie–Poisson systems and classify the prototypes of singularities that cause symmetry breaking. The central idea is the deformation of the underlying Lie algebra; invoking Bianchi’s list of all three-dimensional Lie algebras, we show that the so-called class-B algebras, which are produced by asymmetric deformations of the simple algebra s o ( 3 ) , yield chiral spectra when linearized around their singularities. The theory of deformation is generalized to higher dimensions, including the infinite-dimensional Poisson manifolds relevant to fluid mechanics.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS1992

Direct numerical simulation of instabilities in parallel flow with spherical roughness elements

Results from a direct numerical simulation of laminar flow over a flat surface with spherical roughness elements using a spectral-element method are given. The numerical simulation approximates roughness as a cellular pattern of identical spheres protruding from a smooth wall. Periodic boundary conditions on the domain's horizontal faces simulate an infinite array of roughness elements extending in the streamwise and spanwise directions, which implies the parallel-flow assumption, and results in a closed domain. A body force, designed to yield the horizontal Blasius velocity in the absence of roughness, sustains the flow. Instabilities above a critical Reynolds number reveal negligible oscillations in the recirculation regions behind each sphere and in the free stream, high-amplitude oscillations in the layer directly above the spheres, and a mean profile with an inflection point near the sphere's crest. The inflection point yields an unstable layer above the roughness (where U''(y) is less than 0) and a stable region within the roughness (where U''(y) is greater than 0). Evidently, the instability begins when the low-momentum or wake region behind an element, being the region most affected by disturbances (purely numerical in this case), goes unstable and moves. In compressible flow with periodic boundaries, this motion sends disturbances to all regions of the domain. In the unstable layer just above the inflection point, the disturbances grow while being carried downstream with a propagation speed equal to the local mean velocity; they do not grow amid the low energy region near the roughness patch. The most amplified disturbance eventually arrives at the next roughness element downstream, perturbing its wake and inducing a global response at a frequency governed by the streamwise spacing between spheres and the mean velocity of the most amplified layer.

Deanna, R. G.↗
DOE OSTI2026

Multi‐Sensor Trajectory Reconstruction of the 24 April 2025 Alaska Fireball and Implications for Planetary Defense

On 24 April 2025 at 18:30:57 UTC, a bright daytime fireball over Southcentral Alaska was detected by 37 seismic stations, 16 single infrasound sensors, and four infrasound arrays, yielding 30 ballistic and multiple fragmentation arrivals. Here, the unprecedented density of seismoacoustic coverage enabled detailed reconstruction of the event using acoustic signals, with fragmentation source locations further guiding the identification of Doppler weather radar signatures of a meteorite fall. Incorporation of a radar-derived terminal point yielded a final trajectory solution, which agreed closely with an independent optical trajectory solution from video analysis. The reconstructed entry parameters from seismoacoustic analysis indicate a velocity of 25.3 km/s, an entry angle of 19°, and an energy release of ∼38 t TNT equivalent. Assuming a chondritic composition, the pre-entry object diameter was ∼0.7 m. Using orbital parameters from the optical solution, we estimate meteoroid composition as most likely an L-type ordinary chondrite. The event occurred in the sub-Arctic, where space-based optical systems face challenges in detection, demonstrating the critical role of dense ground-based seismoacoustic networks in characterizing high-latitude atmospheric entries. This uniquely well-recorded event demonstrates the capability of dense seismoacoustic networks to constrain bolide trajectories, energetics, and fragmentation, with radar and optical data providing critical confirmation and complementary perspectives. These results bridge the methodological gap between planetary-defense monitoring of natural impactors and space-traffic analyses of artificial reentries, illustrating how multi-sensor integration can deliver calibration-grade trajectories even for unpredicted events.

Fireball↗
NASA NTRS1981

Impact cratering - The effect of crustal strength and planetary gravity

The effect of varying planetary crustal strength and surface gravity on the depth of impact craters is investigated, by coupling the results of compressible flow, finite difference calculations carried out to stress levels below the compressional dynamic yield point, in keeping with the incompressible fluid flow model of Maxwell (1973). The fundamental assumption in this description is that the amplitude of the particle velocity field decreases with time as kinetic energy is converted into heat and gravitational potential energy. By using a Mohr-Coulomb yield criterion, the effect of varying strength on transient crater depth and on crater formation time in the gravity field of the moon is investigated for the case of 5 km/sec impactors having radii in the 10 to 10 to the 7th cm range.

Okeefe, J. D.↗
DOE OSTI2020

Point defect evolution under irradiation: Finite size effects and spatio-temporal correlations

The evolution of point defect concentrations under irradiation is controlled by their diffusion properties, and by their formation and elimination mechanisms. The latter includes the mutual recombination of vacancies and interstitials, and the elimination of point defects at sinks. Two models are traditionally used to predict the defect concentration evolution, the standard rate theory (SRT) and the atomistic kinetic Monte Carlo (AKMC). We show in this work a large discrepancy in the defect concentrations between both methods when the average number of defects in the AKMC simulation box is close or lower than one. The reason is that AKMC naturally captures strong space and time correlations between vacancies and interstitials generated by the finite size of the periodic simulation box. These correlations strongly affect the recombination rate and the point defect concentrations. SRT fails to predict such correlations, and the corresponding solution deviates from the more accurate solution given by the AKMC simulation under similar conditions. These finite size correlation effects are strong when the elimination of point defects occurs by recombination only, but can still be significant in the presence of sinks. In order to account for the spacio-temporal correlation in a continuum framework, we introduce a Correlated Pair Theory (CPT). This theory fully takes into account the correlations between vacancy and interstitial pairs and predicts point defect concentrations in good agreement with AKMC simulations. Inversely, if the goal is for the AKMC to reproduce defect concentrations in bulk using small simulation boxes, the naturally occurring correlations need to be corrected. We show here that the CPT can be used to modify the elimination rates in the AKMC simulations, so as to yield point defect concentrations in agreement with SRT.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
NASA NTRS1985

GeV gamma-ray astronomy telescopes with high angular resolution

Gamma-ray telescopes flown on satellites have poor angular resolution with typical point source error circles of a few square degrees. It is shown that a major improvement in angular resolution for the detection of gamma-rays in the GeV region can be obtained with a single crystal as converter. The electron produced by a gamma ray incident at a small angle to a major crystal axis or plane is captured into channeling and radiates gamma rays. The channeling radiation and the electron-positron pair can be detected and yield point source locations with a precision of 5 arcseconds at 10 GeV. This is an improvement of three orders of magnitude on the angular precision of telescopes sensitive to gamma-rays above 50 MeV flown on Satellites.

Mcbreen, B.↗
DOE OSTI2023

Giant Increase of Hardness in Silicon Carbide by Metastable Single Layer Diamond-Like Coating

Silicon carbide (SiC) is one of the hardest known materials. Its exceptional mechanical properties combined with its high thermal conductivity make it a very attractive material for a variety of technological applications. Recently, it was discovered that two-layer epitaxial graphene films on SiC can undergo a pressure activated phase transition into a sp3 diamene structure at room temperature. Here, we show that epitaxial graphene films grown on SiC can increase the hardness of SiC up to 100% at low loads (up to 900 µN), and up to 30% at high loads (10 mN). By using a Berkovich diamond indenter and nanoindentation experiments, we demonstrate that the 30% increase in hardness is present even for indentations depths of 175 nm, almost three hundred times larger than the graphene film thickness. The experiments also show that the yield point of SiC increases up to 77% when the SiC surface is coated with epitaxial graphene. These improved mechanical properties are explained with the formation of diamene under the indenter’s pressure.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Synthesis and characterization of biobased copolyesters based on pentanediol: (1) Poly(pentylene dodecanoate–co–furandicarboxylate)

A series of biobased aliphatic-aromatic copolyesters, poly(pentylene dodecanoate-co-furandicarboxylates) (PPeDFs) were synthesized via an esterification and polycondensation melt process. The copolyesters were characterized using gel permeation chromatography, Fourier transform infrared spectroscopy, 1 H NMR spectroscopy, differential scanning calorimetry, thermogravimetric analysis, wide angle x-ray scattering, and tensile testing. The thermal transition behavior was strongly dependent on composition, with the melting and glass transition temperatures reaching a minimum at approximately equimolar ratio of D to F. All copolyesters were stable below 300°C with their R 600 (the weight of material remaining at 600°C) values increasing with F fraction. PPeD to PPeDF30 (e.g., mole ratio D/F = 7:3) show sharp PPeD crystalline reflections only while broad PPeF reflections are shown in PPeF and PPeDF90. PPeDF40 to PPeDF80 showed both crystal structures. The fractional crystallinity for the PPeD was much higher than PPeF and the fractional crystallinity of the copolymers showed a minimum at D/F ratios closer to the latter. Here, the stress at break and modulus both exhibited maxima at D/F ratios that were either high or low, but somewhat surprisingly a strong maximum in percent elongation at break of over 600% occurs at PPeDF40. For this composition, a typical plastic behavior curve was found including a yield point, high elongation at break, and strain hardening.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Structure/property relationship of semicrystalline polymers during tensile deformation: a molecular dynamics approach

Molecular dynamics (MD) simulation with an ab initio numerical model is conducted to study the structure–property relationship of semicrystalline polymers during uniaxial deformation. The effects of chain length, temperature, and strain rate on mechanical properties are discussed. The influences of microstructural evolution such as bond length, entanglement density, and chain orientation are also studied quantitatively. The temperature will greatly affect the chain conformation in amorphous domains, and the results revealed that the interaction of amorphous and crystalline domains played a crucial role during stretching. Accordingly, the yielding of semicrystalline polymers follows different mechanisms at temperatures above and below T g . A melt-recrystallization scheme is observed during yielding at higher temperatures, while destruction of crystal structures is observed at lower temperatures at the yield point. The correlated effects of different temperatures and strain rates on mechanical properties are examined. This research is part of our efforts to develop a digital twin of a real experiment for efficient optimization of polymer material properties.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Proppant embedment in coal and shale: Impacts of stress hardening and sorption

During methane production in CBM reservoirs, the influence of proppant embedment and permeability damage cannot be neglected – especially where the wall-rock is soft. Effective stresses are elevated during methane recovery, increasing both normal loading stress and confinement and simultaneously overprinting sorption-induced volumetric strains. Experiments and analytic modeling are conducted to define key mechanisms controlling these competitive effects. We independently measure overall sample compaction (external LVDT) and local strain (strain gauge) in the matrix to deconvolve proppant embedment in a propped fracture for different conditions of confining stress. The results show symptomatic behaviors of elastic (shale) and elastoplastic (coal) responses of embedment. Different from shale, the evolution of embedment is convex upwards with increased stress where indented depth increases more rapidly as loading stress increases under constant confinement. In addition, a stress-hardening effect is found to play a pivotal role in determining the characteristics of indentation, which are examined in terms of evolution profiles, deformation regimes, embedment slopes, curvatures, yield points and irreversible indentations. Based on the experimental observations a semianalytical model predicts indentation and the evolution of propped permeability under recreated in-situ stress conditions. A simplified case study is conducted to further illustrate the evolution of aperture and permeability of a propped fracture in CBM reservoirs. The modeling results suggest that proppant embedment is significantly overestimated if the variable stress-hardening (VSH) effect is neglected, especially when effective stress is large. Moreover, a decrease in indentation depth possibly occurs during late stage methane production, resulting in a reversal/recovery in fracture closure. This is because desorption-induced shrinkage becomes the predominant effect, causing an increase in aperture and a reduction in the indented volume of proppant. The resulting recovery in permeability implies that the propped coal fracture has the potential to optimally facilitate methane production as a pathway, even at high closure stresses generated by methane drainage.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2022

A systematic method for selecting molecular descriptors as features when training models for predicting physiochemical properties

Machine learning has proven to be a powerful tool for accelerating biofuel development. Although numerous models are available to predict a range of properties using chemical descriptors, there is a trade-off between interpretability and performance. Neural networks provide predictive models with high accuracy at the expense of some interpretability, while simpler models such as linear regression often lack in accuracy. In addition to model architecture, feature selection is also critical for developing interpretable and accurate predictive models. We present a method for systematically selecting molecular descriptor features and developing interpretable machine learning models without sacrificing accuracy. Our method simplifies the process of selecting features by reducing feature multicollinearity and enables discoveries of new relationships between global properties and molecular descriptors. To demonstrate our approach, we developed models for predicting melting point, boiling point, flash point, yield sooting index, and net heat of combustion with the help of the Tree-based Pipeline Optimization Tool (TPOT). For training, we used publicly available experimental data for up to 8351 molecules. Our models accurately predict various molecular properties for organic molecules (mean absolute percent error (MAPE) ranges from 3.3% to 10.5%) and provide a set of features that are well-correlated to the property. This method enables researchers to explore sets of features that significantly contribute to the prediction of the property, offering new scientific insights. To help accelerate early stage biofuel research and development, we also integrated the data and models into a open-source, interactive web tool.

09 BIOMASS FUELS↗
DOE OSTI2023

Predicting the creep-rupture lifetime of a cast austenitic stainless steel using Larson-Miller and Wilshire parametric approaches

An experimental dataset of just over 100 creep tests of a cast austenitic stainless steel, CF8C-Plus, was analyzed by two temperature-compensated parametric models (Larson-Miller, Wilshire et al.) to predict long-term lifetimes as functions of temperature and stress. The dataset and associated regression analyses showed greater scatter than typically found in recent similar studies of wrought Ni-based alloys by the same two models and was attributed to the microstructural inhomogeneity of the cast stainless steel. Qualitatively, the Larson-Miller formalism showed greater lifetime prediction accuracy than the Wilshire approach, with the latter model's predictive ability being particularly degraded by the presence of two very significant outlier results. This observation suggests that the Larson-Miller approach is more robust when treating rupture-time datasets that show particularly wide experimental scatter. Despite the differences in the overall predictive ability, both models yielded similar predictions of the applied stress at which CF8C-Plus would have a creep-limited lifetime of 100,000 h when loaded below the yield point.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Performance and transport in the ARC tokamak

The ARC TM tokamak, a high-field (𝐵 𝑇 = 11.4 T) fusion power plant, under development by Commonwealth Fusion Systems, is studied using a suite of integrated modelling tools to predict its fusion power generation (𝑃𝑓⁡𝑢⁢𝑠), transport and confinement properties. Analysis is based off an ARC operational point scoped first with zero-dimensional (0-D) plasma operational contour (POPCON) modelling to produce 1.13 GW of fusion power. A suite of integrated modelling tools (TRANSP, ASTRA and TORAX) were applied to predict the performance and kinetic profiles of the ARC design point, yielding a range of predicted performance spanning from ∼900 to 1300 MW in rough quantitative agreement with POPCON predictions. The sensitivity of these results to uncertain modelling inputs was probed using scans of pedestal boundary conditions around EPED-predicted values (total pressure and temperature ratios), tungsten concentration and seperatrix density around their nominal assumptions. Pedestal pressure and pedestal top (𝑇 𝑖 /𝑇 𝑒 ) play a large role in 1.5-dimensional performance predictions, able to modify the predicted 𝑃 𝑓⁡𝑢⁢𝑠 by a factor of 2 within reasonable assumptions. High-fidelity core nonlinear gyrokinetic profile predictions, performed using CGYRO (Candy et al. 2016 J. Comput. Phys., vol. 324, pp. 73–93) coupled with the PORTALS (Rodriguez-Fernandez et al. 2024 Nucl. Fusion, vol. 64, 076034; Phys. Plasmas, vol. 31, 2024, 062501) framework, yield substantially lower performance (𝑃 𝑓⁡𝑢⁢𝑠 =677 MW) compared with 0-D and medium-fidelity modelling for nominal assumptions, showing that there is non-negligible uncertainty between models and that future work on SPARC may help resolve discrepancies. Lower overall performance results from significantly reduced volume-averaged densities and temperatures, along with reduced levels of density and temperature peaking. Turbulence and transport are largely dominated by ion temperature gradient across the profile, confirmed by both linear stability and the response of the nonlinear fluxes to changes in gradients, with some impact of kinetic ballooning modes in the deep core. This work represents one of the most complete scoping of potential fusion power plant conditions performed to date. The extensive integrated modelling provides confidence in ARC performance approaching 1 GW, while nonlinear gyrokinetic modelling results in open questions into the physics of density and temperature peaking in fusion-power-plant-relevant operational space. A discussion of results and the role that the SPARC tokamak (Creely et al. 2020 J. Plasma Phys., vol. 86, 865860502) will play in informing ARC design, performance and operation is presented.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Altered post-fracture systemic bone loss in a mouse model of osteocyte dysfunction

Femur fracture leads to loss of bone at uninjured skeletal sites, which may increase risk of subsequent fracture. Osteocytes, the most abundant bone cells, can directly resorb bone matrix and regulate osteoclast and osteoblast activity, but their role in systemic bone loss after fracture remains poorly understood. In this study we used a transgenic (TG+) mouse model that overexpresses human B-cell lymphoma 2 (BCL-2) in osteoblasts and osteocytes. This causes enhanced osteoblast proliferation, followed by disruption in lacunar-canalicular connectivity and massive osteocyte death by 10 wk of age. We hypothesized that reduced viable osteocyte density would decrease the magnitude of systemic bone loss after femur fracture, reduce perilacunar remodeling, and alter callus formation. Bone remodeling was assessed using serum biomarkers of bone formation and resorption at 5 d post-fracture. We used micro-computed tomography, high resolution x-ray microscopy, mechanical testing, and Raman spectroscopy to quantify the magnitude of systemic bone loss, as well as changes in osteocyte lacunar volume, bone strength, and bone composition 2 wk post-fracture. Fracture was associated with a reduction in circulating markers of bone resorption in non-transgenic (TG-) animals. TG+ mice exhibited high bone mass in the limbs, greater cortical elastic modulus and reduced post-yield displacement. After fracture, TG+ mice lost less trabecular bone than TG- mice, but conversely TG+ mice exhibited trends toward a lower yield point and reduced femoral cortical thickness after fracture, though these were not statistically significant. Lacunar density was greater in TG+ mice, but fracture did not alter lacunar volume in TG+ or TG- mice. These findings suggest that osteocytes potentially play a significant role in the post-traumatic systemic response to fracture, though the effects differ between trabecular and cortical bone.

60 APPLIED LIFE SCIENCES↗