Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “yield point”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

New Mechanism for Yield Point Phenomena

Yield point phenomena (YPP) are widely attributed to discrete dislocation locking by solute atmospheres. An alternate YPP mechanism was recently suggested by simulations of Ta single crystals without any influence of solutes or discrete dislocations. The general meso-scale (GM) simulations consist of crystal plasticity (CP) plus accounting for internal stresses of geometrically necessary dislocation content. GM predicted the YPP while CP did not, suggesting a novel internal stress mechanism. The predicted YPP varied with crystal orientation and boundary conditions, contrary to expectations for a solute mechanism. The internal stress mechanism was probed by experimentally deforming oligocrystal Ta samples and comparing the results with independent GM simulations. Strain distributions of the experiments were observed with high-resolution digital image correlation. A YPP stress–strain response occurred in the 0–2% strain range in agreement with GM predictions. Shear bands appeared concurrent with the YPP stress–strain perturbation in agreement with GM predictions. At higher strains, the shear bands grew at progressively slower rates in agreement with GM predictions. It was concluded that the internal stress mechanism can account for the existence of YPP in a wide variety of materials including ones where interstitial-dislocation interactions and dislocation transient avalanches are improbable. Furthermore, the internal stress mechanism is a CP analog of various micro-scale mechanisms of discrete dislocations such as pile-up or bow-out. It may operate concurrently with strain aging, or either mechanism may operate alone. A suggestion was made for a future experiment to answer this question.

42 ENGINEERING↗
DOE OSTI2022

On the Prediction of Uniaxial Tensile Behavior Beyond the Yield Point of Wrought and Additively Manufactured Ti-6Al-4V

In this paper, phenomenological relationships are presented that permit the prediction of the plastic regime of stress–strain curves using a limited number of parameters. These relationships were obtained from both conventional (wrought + β annealed) and additively manufactured (i.e., “3D printed”) Ti-6Al-4V. Three different methods of additive manufacturing have been exploited to produce the materials, including large-volume electron beam additive manufacturing, large-volume laser hot wire additive manufacturing, and small-volume selective laser melting. The general fundamental expressions are independent not only of the additive manufacturing process, but also of a wide variety of post-deposition heat treatments, however the coefficients are specific to material states. Thus, this work demonstrates that it is possible to predict not only the ultimate tensile strength, but also the full true stress, true strain curves, if certain parameters of the material are known. In general, the prediction of ultimate tensile strength are within 5% of the experimentally measured values across all additive manufacturing variants and subsequent heat treatments. The absolute values of ultimate tensile strength range from ~ 910 MPa to ~ 1170 MPa for the single alloy Ti-6Al-4V. Data representing 113 explicit samples are included in this work.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Characterizing The Mechanical Properties of Polyurethane Foams

The Department of Energy has many radioactive facilities that are on the path of deactivation and decommissioning (D and D). These facilities can sit cold and dark for many years before final disposition, and must be maintained to ensure no radiological release occurs in the interim. Improvements and additions to D and D tool sets can greatly: Save time and money, Reduce worker risk. Conventional fixatives widely used often take the form of paints or films that are not readily applicable to 3-dimensional void spaces. Foams are one promising platform that may offer solutions to a number of contaminated problem sets such as: Gloveboxes, Pipes, Tanks. SRNL is working to characterize various commercial foams that would encapsulate the interior volume of a given space and are capable of immobilizing any remaining contamination. One key performance metric of these foams is how well they will perform in an accident scenario. To this end, SRNL is researching the mechanical properties of these foams to ensure that the material can withstand the environment of application while maintaining structural integrity. ASTM standard E3191-18 served as a guiding document for this project, outlining the requirements that foaming fixatives used for the mitigation of radioactive contamination need to meet before being implemented. Objective: Quantification of the mechanical properties of 6 commercial polyurethane foams was performed using multiple ASTM standards to record measurements for: Compression testing: Flexible Foams, Force required to produce 50% compression, Rigid Foams, Compressive and apparent modulus, Point of 10% core deformation, The 'Zero Deformation' point, Compressive strength, Yield point. Tensile testing: Tensile strength, Tensile stress, Percent elongation. Experiment 1: An electromechanical compressive tester (MTS Criterion Series 43) was used to evaluate 6 foams (4 flexible, 2 rigid). Per ASTM D1621, each rigid foam was compressed at 10% of the measured thickness per minute until the sample was 13% of it's original thickness. Per ASTM D35/4, each flexible foam was pre-flexed twice to 80% original thickness at a rate of 250 mm/min, then compressed to 80% original thickness at a rate of 50 mm/min. Experiment 2: An electromechanical tensile tester (MTS Criterion Series 43) was used to evaluate 6 foams (4 flexible, 2 rigid). Per ASTM D1623, rigid foams were pulled apart at a rate of 1.27 mm/min until the sample broke. Per ASTM D35/4, flexible foams were pulled apart at a rate of 500 mm/min until the sample broke. The strongest material in both compression and tensile testing scenarios was found to be the rigid intumescent polyurethane Hilti foam. The experiments revealed that the Hilti foam in a tensile scenario had a peak stress value that was larger than the closest competitor by a factor of 2.3 and a compressive yield point that was larger than the closest competitor by a factor of 1.4, indicating that the Hilti foam is the best choice for implementation in mechanically harsh environments. The performance metrics measured can serve as a basis for future mechanical tests that would help set relevant ASTM standards (E3191) for intumescent polyurethane foams in fixating applications. Tests like surface adhesion, impact, and flame tests would serve as a better indicator as to how this material would perform in environmentally harsh scenarios often found in decommissioned nuclear facilities. Further tests of the foams' intumescent properties would also be important should these foams be implemented in environmentally harsh scenarios.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
NASA NTRS1995

Investigation of Strain Aging in the Ordered Intermetallic Compound beta-NiAl

The phenomenon of strain aging has been investigated in polycrystalline and single crystal NiAl alloys at temperatures between 300 and 1200 K. Static strain aging studies revealed that after annealing at 1100 K for 7200 s (i.e., 2h) followed by furnace cooling, high purity, nitrogen-doped and titanium-doped polycrystalline alloys exhibited continuous yielding, while conventional-purity and carbon-doped alloys exhibited distinct yield points and Luders strains. Prestraining by hydrostatic pressurization removed the yield points, but they could be reintroduced by further annealing treatments. Yield points could be reintroduced more rapidly if the specimens were prestrained uniaxially rather than hydrostatically, owing to the arrangement of dislocations into cell structures during uniaxial deformation. The time dependence of the strain aging events followed at t(exp 2/3) relationship suggesting that the yield points observed in polycrystalline NiAl were the result of the pinning of mobile dislocations by interstitials, specifically carbon. Between 700 and 800 K, yield stress plateaus, yield stress transients upon a ten-fold increase in strain rate, work hardening peaks, and dips in the strain rate sensitivity (SRS) have been observed in conventional-purity and carbon-doped polycrystals. In single crystals, similar behavior was observed; in conventional-purity single crystals, however, the strain rate sensitivity became negative resulting in serrated yielding, whereas, the strain rate sensitivity stayed positive in high purity and in molybdenum-doped NiAl. These observations are indicative of dynamic strain aging (DSA) and are discussed in terms of conventional strain aging theories. The impact of these phenomena on the composition-structure-property relations are discerned. Finally, a good correlation has been demonstrated between the properties of NiAl alloys and a recently developed model for strain aging in metals and alloys developed by Reed-Hill et al.

Weaver, Mark Lovell↗
NASA NTRS1996

Kinetics of Static Strain Aging in Polycrystalline NiAl-based Alloys

The kinetics of yield point return have been studied in two NiAl-based alloys as a function of aging time at temperatures between 300 and 700 K. The results indicate that the upper yield stress increment, Delta sigma(sub u) (i.e., stress difference between the upper yield point and the final flow stress achieved during prestraining), in conventional purity (CP-NiAl) and in high purity carbon-doped (NiAl-C) material first increased with a t(exp 2/3) relationship before reaching a plateau. This behavior suggests that a Cottrell locking mechanism is the cause for yield points in NiAl. In addition, positive y-axis intercepts were observed in plots of Delta sigma(sub u) versus t(exp 2/3) suggesting the operation of a Snoek mechanism. Analysis according to the Cottrell Bilby model of atmosphere formation around dislocations yields an activation energy for yield point return in the range 70 to 76 kJ/mol which is comparable to the activation energy for diffusion of interstitial impurities in bcc metals. It is, thus, concluded that the kinetics of static strain aging in NiAl are controlled by the locking of dislocations by Cottrell atmospheres of carbon atoms around dislocations.

Weaver, M. L.↗
NASA NTRS1996

Observations of Static Strain-Aging in Polycrystalline NiAl

Static strain-aging has been investigated in eight polycrystalline NiAl alloys. After annealing at 1100 K for 7200 s followed by furnace cooling, high-purity, nitrogen-doped, and titanium-doped alloys exhibited continuous yielding, while conventional-purity and carbon-doped alloys exhibited distinct upper yield points and Luders strains. Either water quenching from 1100 K or prestraining via hydrostatic pressurization suppressed the yield points in the latter alloys, but they could be reintroduced by further annealing treatments. Yield points could be reintroduced more rapidly if the specimens were prestrained uniaxially rather than hydrostatically, owing to the arrangement of dislocations into cell structures during uniaxial deformation. Chemical analysis suggests that the species responsible for strain-aging is interstitial carbon.

Weaver, M. L.↗
DOE OSTI2023

Molecular-Dynamics Analysis of the Mechanical Behavior of Plasma-Facing Tungsten

We report a systematic computational analysis of the mechanical behavior of plasma-facing component (PFC) tungsten focusing on the impact of void and helium (He) bubble defects on the mechanical response beyond the elastic regime. Specifically, we explore the effects of porosity and He atomic fraction on the mechanical properties and structural response of PFC tungsten, at varying temperature and bubble size. We find that the Young modulus of defective tungsten undergoes substantial softening that follows an exponential scaling relation as a function of matrix porosity and He atomic content. Beyond the elastic regime, our high strain rate simulations reveal that the presence of nanoscale spherical defects (empty voids and He bubbles) reduces the yield strength of tungsten in a monotonically decreasing fashion, obeying an exponential scaling relation as a function of tungsten matrix porosity and He concentration. Our detailed analysis of the structural response of PFC tungsten near the yield point reveals that yielding is initiated by emission of dislocation loops from bubble/matrix interfaces, mainly 1/2<111> shear loops, followed by gliding and growth of these loops and reactions to form <100> dislocations. Furthermore, dislocation gliding on the <111>{211} twin systems nucleates 1/6<111> twin regions in the tungsten matrix. These dynamical processes reduce the stress in the matrix substantially. Subsequent dislocation interactions and depletion of the twin phases via nucleation and propagation of detwinning partials lead the tungsten matrix to a next deformation stage characterized by stress increase during applied straining. Furthermore, our structural analysis reveals that the depletion of twin boundaries (areal defects) is strongly impacted by the density of He bubbles at higher porosities. After the initial stress relief upon yielding, increase in the dislocation density in conjunction with decrease in the areal defect density facilitates the initiation of dislocation-driven deformation mechanisms in the PFC crystal.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Predicting the viscoplastic response of a crystallizing fluoropolymer using transient network theory

We employ a molecular theory of dynamic polymer networks to describe the viscoplastic response of rubbery FK-800, a thermoplastic copolymer of chlorotrifluoroethylene and vinylidene fluoride, over a broad range of thermal histories. The kinetics of crystallization at different annealing temperatures was modeled using a modified Avrami equation, whose parameters were found to evolve through simple relationships over the full temperature range of the rubbery state. By fitting experimental compression data, we discovered predictable trends for the physical parameters in our mechanical model over its full range of crystallinities (up to ≈20%) and provided insights based on molecular-level physics to justify them. Using this, an end-to-end model was developed to predict the yielding and post-yield behavior of rubbery FK-800 for arbitrary thermal histories. The model successfully predicted the highly nonlinear evolution of characteristic mechanical signatures (stiffness, yield point, post-yield drop) throughout the crystallization process. A statistical analysis of variance test was employed to determine that the measured variations in the mechanical behavior of rubbery FK-800 are primarily dictated by its fractional crystallinity, regardless of its exact thermal history.

36 MATERIALS SCIENCE↗
NASA NTRS1969

2-substituted-5-methyl-2-oxazolines

Cyclization of N-allylamides to disubstituted- 2-oxazolines, giving melting points, yields, picrate melting points and NMR spectra

Carroll, J. T.↗
NASA NTRS1936

The stress criterion of a tension member with graded flexural stiffness : contribution to the problem of "clamping effect" outside of the elastic range

The approximate size of the stress criterion of a bar on two supports stressed beyond the elastic range is assessed by an approximation. The calculation proceeds from the premise of "substitute flexural stiffness" so defined that the part stressed beyond the elastic range may be considered as following Hooke's law when determining the flexural deformation quantities. For the determination of the substitute flexural stiffness, it is presumed that the material is already stressed so much beyond the yield point as to be strain-hardened. The data are directly applicable to materials having no definite yield point. For the rest, von Karman's method for compressed and subsequently deflected bars serves as basis for the calculation.

Kaul, Hans W↗
NASA NTRS2024

Scalability in SLA lattice through lattice orientation and hybrid frame and plate architectures

Lightweighting has been a key goal for engineers and designers, with lattice structures widely explored as the building blocks for structural components. Cellular structure-inspired lattice truss frame designs made of struts, have been extensively studied. All plate-based lattice designs have superior mechanical performance. Limits in scalability occur from formation of closed pockets limiting uv curing in processes like stereolithography (SLA). We examine hybrid frame and plate body-centered cubic-simply cubic (BCC-SC) lattices under compression. Unit cells and scaled up lattice exhibit an increase in yield stress and modulus with the addition of plates. The loading direction on the hybrid frame and plate unit cells affected the magnitude of improvement. Simulations and measurements indicated that the optimal lightweight lattice was determined to be when two plates were placed opposite each other with plates buttressing the struts, inhibiting buckling of the struts aligned with the loading direction. This lattice resulted in 63% improvement in specific modulus, a 137% improvement in specific yield point, and a 360% improvement in specific energy absorption (SEA) and the scaled up 4 × 4 × 4 scaled-up structures, showed a 107%, 148%, and 297% in specific modulus, specific yield point, and SEA, respectively A combined stretching-bending behavior was identified in optimal orientations reflecting the delayed buckling mechanism paired to a rising stress-strain curve past the elastic yield indicating bending resistance. The mass moment of inertia was found to be a key parameter correlating optimum orientation for the same number of plates added to the BCC-SC frame.

Mahan Ghosh↗
DOE OSTI2020

Deformation behavior of metallic glass composites and plasticity accommodation at microstructural length-scales

Bulk metallic glass matrix composites represent a unique microstructural design strategy for overcoming the strength/ductility trade-off in structural alloys. Site-specific mechanical behavior of a Ti-based bulk metallic glass composite was evaluated at microstructural length-scale. The micro-pillars on the amorphous matrix showed on average a yield point of 1.9 GPa followed by serrated plastic deformation characteristic of shear banding. In contrast, micro-pillars on the crystalline dendritic phase showed a much lower yield strength of 0.72 GPa on average for the four different crystallographic orientations chosen, smooth plastic flow with no recognizable load burst, and stable strain-hardening after yield point. A number of micro-pillars were made at the interface between the glassy matrix and the crystalline dendrite. The mixed micro-pillars showed homogeneous deformation and greater plasticity which was attributed to their smaller stored elastic energy. Shear bands initiated in the amorphous matrix were arrested by the crystalline dendrite, which accommodated plasticity through slip bands and dislocations pile-ups. The interface remained intact after plastic deformation, with no observable signs of devitrification in the amorphous phase.

Bulk metallic glass matrix composite, Micro-pillar↗
DOE OSTI2021

Mechanical behavior of ultralight nickel metamaterial

The mechanical response of ultralight kagomé structures consisting of hollow nickel (Ni) nanotubes and solid Ni nanorods to compression is studied using molecular dynamics simulations. In both kagomé architectures, 16[112] Shockley partial dislocations and twin formation are observed under compression. The structure made from solid nanorods shows deformation near both the nodes and beams of the kagomé lattice. The hollow kagomé architecture has a higher yield point than the solid kagomé structure. The deformation in the hollow nanotube structure is mostly localized in the nodal region for strains less than 11%. At higher strains, the deformation sets in all the struts and nodes of the hollow kagomé lattice. Owing to this two-stage deformation mechanism, the hollow Ni nanotube kagomé structure shows less bending and greater toughness than the solid Ni nanorod kagomé architecture.

Rajak, Pankaj (ORCID:0000000263446056)↗
NASA NTRS2014

Viscoelastic Response of the Titanium Alloy Ti-6-4: Experimental Identification of Time- and Rate-Dependent Reversible and Irreversible Deformation Regions

In support of an effort on damage prognosis, the viscoelastic behavior of Ti-6Al-4V (Ti-6-4) was investigated. This report documents the experimental characterization of this titanium alloy. Various uniaxial tests were conducted to low load levels over the temperature range of 20 to 538 C to define tensile, creep, and relaxation behavior. A range of strain rates (6x10(exp -7) to 0.001/s) were used to document rate effects. All tests were designed to include an unloading portion, followed by a hold time at temperature to allow recovery to occur either at zero stress or strain. The titanium alloy was found to exhibit viscoelastic behavior below the "yield" point and over the entire range of temperatures (although at lower temperatures the magnitude is extremely small). These experimental data will be used for future characterization of a viscoelastic model.

stress relaxation↗
DOE OSTI2025

Non-linear elastic-plastic behavior of the invert glass lithium phosphorous oxynitride (LiPON)

Micro and nano-scale mechanical behavior of network/ionic glasses is dictated by their composition and the number of constraints per structural unit. From this perspective, the glass LiPON presents the opportunity for enhancement of the microscale ductility due to its rather unconstrained orthophosphate structure. Here, we use instrumented nanoindentation with different tip geometries to investigate the mechanical response of LiPON glass. The results reveal that the elastic modulus of LiPON is not constant and depends on pressure. With the method utilizing spherical nanoindentation and continuous stiffness measurement (CSM) we determine the yield point of LiPON. We propose the Drucker-Prager type of yield criterion for LiPON and estimate its yield stress in compression as 2.4 GPa. There exists another stress threshold, however, around 490 MPa, at which the elastic deformation becomes non-linear, and this can be mistaken for the yield stress.

Constitutive model↗
NASA NTRS2017

Molecular Based Temperature and Strain Rate Dependent Yield Criterion for Anisotropic Elastomeric Thin Films

A molecular formulation of the onset of plasticity is proposed to assess temperature and strain rate effects in anisotropic semi-crystalline rubbery films. The presented plane stress criterion is based on the strain rate-temperature superposition principle and the cooperative theory of yielding, where some parameters are assumed to be material constants, while others are considered to depend on specific modes of deformation. An orthotropic yield function is developed for a linear low density polyethylene thin film. Uniaxial and biaxial inflation experiments were carried out to determine the yield stress of the membrane via a strain recovery method. It is shown that the 3% offset method predicts the uniaxial elastoplastic transition with good accuracy. Both the tensile yield points along the two principal directions of the film and the biaxial yield stresses are found to obey the superposition principle. The proposed yield criterion is compared against experimental measurements, showing excellent agreement over a wide range of deformation rates and temperatures.

Bosi, F.↗