Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface wetting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Electrochemical Modeling of PID Leakage Current of PV Modules: Steady-State Current, Transient Current, and RC-Equivalent Circuit

Potential-induced degradation (PID) remains a significant reliability concern for photovoltaic (PV) modules, arising when a voltage difference between the module frame and the solar cells drives unintended leakage current through the glass-encapsulant stack. Although PID ultimately manifests as PID-s, PID-p, or PID-c, the underlying behavior of the leakage current-its magnitude and time dependence-requires clearer electrochemical interpretation. Traditional explanations attribute the initial transient current to bulk capacitive elements of the glass, encapsulant, and antireflection coatings, and the steady-state current according to their effective ohmic resistance. More recent studies, however, indicate that electrochemical charge-transfer processes at the encapsulant-metallization interface can play a dominant role in defining the leakage-current path. This paper develops a unified electrochemical framework for modeling PID leakage current. First, an RC-equivalent circuit is formulated by combining conventional RC elements with a Randles-type interface to capture transient leakage current through double-layer capacitance and faradaic processes at ionic-electronic boundaries. Second, the steady-state current-voltage behavior is explained using a linearized Butler-Volmer relationship, showing that the measured ohmic response corresponds to the low-overpotential limit of charge-transfer kinetics. Analytical results demonstrate that, for typical module materials-3.2-mm soda-lime glass and 0.45-mm encapsulant-the dominant modulators to PID leakage current are the glass surface resistance (under dry-surface conditions), the glass bulk capacitance, and the encapsulant resistance (under wet-surface conditions), with soda lime glass surface and EVA/POE encapsulant resistances primarily governing steady-state current. The proposed electrochemical model is validated against measured leakage-current data, showing good agreement in both the magnitude and the time-dependent evolution of PID leakage current.

14 SOLAR ENERGY↗
DOE OSTI2022

Low-temperature electroplating of zirconium: Ionic mixture methods

Non-aqueous ionic mixture electroplating allows for room-temperature or near-room-temperature applications of thin metal films, typically metals for which aqueous solvents cannot be used. While there are many methods of plating zirconium, each has disadvantages that ionic liquid plating could correct. However, ionic liquid plating requires further research and development, as a new class of solvents were only developed a few years ago. Current ionic liquids cost several thousand dollars per liter, yet produce films with less than 90% surface coverage as well as deposition of salt species that enable interdiffusion through the Zr. Film coverage needs to be increased while maintaining approximate room temperatures and lower solvent costs. Current ionic liquid technology has suffered from poor surface wetting and limited Zr diffusivity leading to dendrite formation which inhibits total surface coverage. Zr electroplating can be improved by application of room-temperature ionic mixtures as the plating medium. We have successfully demonstrated the capability to plate high-quality metallic zirconium layers using deep eutectic solvents (DES) and DES-ionic liquid (IL) mixtures. Plating thicknesses of up to 6 microns have been achieved, and the coatings are conformal to the substrate and not dendritic, with low contamination from the plating solution. Our current method uses the DES ethaline (a 1:2 ratio of choline chloride and ethylene glycol) to complex zirconium (IV) ions (present via the addition of ZrF4). We pulse plate the Zr from a bath with an overabundance of LiF, in accordance with prior literature. We have also had success in mixing the DES with ILs, such as Triethylsulfonium bis(trifluoromethylsulfonyl)imide, 1-Butyl-3-methylpyridinium bis(trifluormethylsulfonyl)imide, Methyl-trioctylammonium bis(trifluoromethylsulfonyl)imide, and Diethylmethyl(2-methoxyethyl)ammonium bis(trifluoromethylsulfonyl)imide.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Experimental investigation of surface roughness/wettability pattern effect on crystallization fouling over falling-film flow

In many industries, including desalination, scaling in heat exchangers is a persistent issue, and most methods of scaling control involve environmentally hazardous chemical additives. Exploiting the effects of surface features and flow-imposed shear on salt deposition might introduce a new approach to scale management, opening the possibility of self-cleaning surfaces. In this work, we experimentally explore surface roughness and wettability patterns interaction with salt deposition and flow shear. Heat transfer and scale mass deposition on flat surfaces are measured during thin-film evaporation of calcium sulfate solution. A wide range of surface roughness (0.027–2.66 μm) is studied at fixed flow and heat flux conditions. Due to improved mixing, heat transfer is enhanced with rougher surfaces initially; however, degrades more quickly than smoother surfaces. Following a period of initial mass deposition fluctuation, a steady scaling stage is observed, with rough surfaces scaling more than smooth surfaces. Wettability patterned surfaces can suppress crystal nucleation without sacrificing overall surface wetting, resulting in antifouling performance and heat transfer enhancement. Scale mass deposition on a patterned surface is reduced by 60 %, and 27 % heat transfer improvement over the baseline surface is found. Furthermore, this study provides guidance to surface manipulation for heat transfer improvement and fouling mitigation.

42 ENGINEERING↗
DOE OSTI2026

Extreme Nanoconfinement Dramatically Enhances Small Molecule Solubility in Nonpolar Polymers

Elucidating gas solubility in confined polymer systems addresses a fundamental gap in polymer physics and has important implications for gas barrier and separation technologies and polymer upcycling reactions. In this study, we examine the solubility of methanol and n-hexane in polystyrene and low-density polyethylene confined within the interstitial pores of disordered silica nanoparticle packings. Using capillary rise infiltration, these polymers are infiltrated into the nanoparticle packings. Gas solubility in these confined polymers is measured using a quartz crystal microbalance. Remarkably, confinement leads to a 10- to ∼100-fold increase in gas solubility. Systematic experiments reveal that pore size plays a dominant role in increasing solubility. In contrast, the molecular weight of the polymer and the surface wetting characteristics of the nanoparticles, achieved by hydrophobically modifying the nanoparticles, have minimal effects. By systematically varying penetrant polarity, polymer crystallinity, pore size, and nanopore surface chemistry, this study isolates geometric nanoconfinement as the dominant factor governing solubility enhancement in confined polymers. Atomistic simulations revealed that confinement and surface−polymer interactions both contribute to enhanced solubility, with polymer packing playing a significant role in modulating gas uptake. Here, these results suggest that the changes in the molecular arrangements of polymer segments underlie the observed trends. This study highlights the potential of confined polymers in engineering the separation performance of membranes and heterogeneously catalyzed polymer upcycling reactions.

alcohols↗
DOE OSTI2025

Convective heat transfer enhancement through additively built multiscale micro-tetrahedron features

Use of Additive Manufacturing (AM) to improve the heat transfer characteristics of tip shrouds in high-pressure turbines is being considered by industries. Existing designs of these components integrate micro-cooling channels to reduce the bulk temperature for improved life. In this research, closely packed micro tetrahedron features in addition to AM roughness has been considered. Further, this multiscale surface characteristics increased surface area per unit volume available for heat exchange. Micro-tet features were designed, manufactured, characterized, and evaluated systematically while increasing their height. An enormous increase in the overall wetted surface area by 200 % was measured. The convective heat transfer enhancement was ~3.72 times EDM rough coupon, and friction factor enhancement was ~5.5 times EDM rough coupon. Furthermore, the proposed design offers 2.5 times enhanced heat transfer for a given 2 W pumping power compared to our EDM rough coupon. Heat transfer enhancement was observed to not vary strongly with increased Reynolds number. Such complex designs are only possible through additive manufacturing for increased heat transfer with little pressure penalty. Finally, increasing the micro-tet height for increased surface area and improved heat exchange beyond an upper limit might not be a significant benefit as it gets compensated by increasing skin friction.

42 ENGINEERING↗
DOE OSTI2024

Effect of Wettability Gradient on the Scale Formation in Falling Film Flow

Mitigation of scale formation and performance degradation remains a vital challenge for falling film evaporators in various industries. In this work, an experimental study of falling film flow on a horizontal tube is conducted to investigate the effects of wettability gradients on thermal, hydraulic, and fouling behavior. It is revealed that certain hydrophobic coating patterns, such as strip, ring, and grid patterns, lead to unwetted heat transfer area, which results in decreased heat transfer compared to fully wetted plain tube. By adjusting the geometry and position of the wettability gradient, the hybrid coating demonstrates improved heat transfer performance. Based on the characteristics of horizontal tube falling film flow, impinging jet, thin film flow, and liquid retention at the tube bottom, a hybrid coating pattern is developed to improve surface wetting and mitigate the scaling coverage. It is revealed that scale deposition is regulated by wettability gradient. Crystals tend to be dense and compact in hydrophilic areas, while they appear scattered or even absent in hydrophobic regions, depending on the dimension of the hydrophobic area. While at the hydrophilic/hydrophobic boundary, a noticeable scale thickness step is observed, which raises the potential for self-cleaning. Furthermore, the balance of minimization of scaling layer coverage and maximization of wetting area requires an optimal design in coating dimensions, for which a systemic study of both flow dynamics and fouling characteristics on the falling film is necessary in the future.

42 ENGINEERING↗
DOE OSTI2023

Using Atmospheric Inverse Modelling of Methane Budgets with Copernicus Land Water and Wetness Data to Detect Land Use-Related Emissions

Climate change mitigation requires countries to report their annual greenhouse gas (GHG) emissions and sinks, including those from land use, land use change, and forestry (LULUCF). In Finland, the LULUCF sector plays a crucial role in achieving net-zero GHG emissions, as the sector is expected to be a net sink. However, accurate estimates of LULUCF-related GHG emissions, such as methane (CH 4 ), remain challenging. We estimated LULUCF-related CH 4 emissions in Finland in 2013–2020 by combining national land cover and remote-sensed surface wetness data with CH 4 emissions estimated by an inversion model. According to our inversion model, most of Finland’s CH 4 emissions were attributed to natural sources such as open pristine peatlands. However, our research indicated that forests with thin tree cover surrounding open peatlands may also be a significant source of CH 4 . Unlike open pristine peatlands and pristine peatlands with thin tree cover, surrounding transient forests are included in the Finnish GHG inventory if they meet the criteria used for forest land. The current Finnish national GHG inventory may therefore underestimate CH 4 emissions from forested organic soils surrounding open peatlands, although more precise methods and data are needed to verify this. Given the potential impact on net GHG emissions, CH 4 emissions from transitional forests on organic soils should be further investigated. Furthermore, the results demonstrate the potential of combining atmospheric inversion modelling of GHGs with diverse data sources and highlight the need for methods to more easily combine atmospheric inversions with national GHG inventories.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

Experimental investigation of a closed vapour box module for a divertor-like configuration in Magnum-PSI

Efficient management of extreme heat fluxes in the divertor region to extend the lifetime of the components remains a critical challenge for the realization of nuclear fusion-based power plants. Among the alternative concepts explored for the divertor region, the use of liquid metals, particularly lithium, is of interest due its ability to dissipate the incoming plasma heat flux through the vapour shielding effect (VS). In this work, we experimentally investigated a ‘closed’ configuration of a dedicated Vapour Box Module (VBM) in the linear plasma device Magnum-PSI. The goal of the experiments is to simulate the vapour box divertor environment conditions and assess its performance in terms of power mitigation and redistribution and lithium confinement. Initial testing without Li demonstrated the efficacy of a closed VBM structure in inducing detachment via neutral gas accumulation. Apertures which enabled non-condensing gas to be effectively pumped while ensuring lithium condensed on the inner surfaces were therefore added. With a lithium capillary porous structure target used, lithium is directly vaporized by the plasma, forming a dense lithium vapour cloud that interacts with the incoming plasma. This resulted in a significant reduction of the target temperature of at least 48%, together with a temperature locking effect, a phenomenon typically observed in the VS regime. Lithium vapour confinement within the VBM was strongly correlated with the wall temperature. Relatively cold walls promoted Li re-condensation and therefore improved Li confinement, although with the expected trade-off of increased hydrogenic retention on lithium-wetted surfaces. As the wall temperature increased, the confinement efficiency decreased, consistent with reduced Li re-condensation and thermally activated Li–H chemistry and remobilization at the walls. Diagnostic measurements through embedded thermocouples and calorimetry revealed that lithium vaporization and re-condensation processes also playedsignificant roles in plasma power dissipation. The results advance the case for a closed divertor chamber with direct lithium evaporation from the strike-points as a viable method to manage divertor heat fluxes in future fusion reactors.

Romano, Fabio [Dutch Institute for Fundamental Ene↗
DOE OSTI2022

Effect of Gold Catalyst Surface Morphology on Wetting Behavior and Electrochemical CO 2 Reduction Performance in a Large-Area Zero-Gap Gas Diffusion Electrolyzer

We report catalyst surface area and wetting behavior are key factors in determining the performance of gas diffusion electrode (GDE) electrolyzers for electrochemical CO 2 reduction. In this work, we report the integration of sub-1 μm thick nanoporous gold (npAu) catalyst coatings into a large-area (25 cm 2 ) zero-gap electrolyzer. The npAu coatings were prepared by magnetron sputtering (MS) of thin AgAu alloy films on the microporous carbon layer of a gas diffusion layer (GDL) followed by Ag leaching. Compared to MS Au films of the same thickness, npAu catalyst coatings enable higher Faradaic efficiencies and improved catalyst stability for CO 2 -to-CO reduction with Faradaic efficiencies of up to 88% at 100 mA/cm 2 . For a 800 nm npAu coating, the device level energy efficiency for CO 2 to CO conversion reaches 45% (52% for CO + H 2 ) at 100 mA/cm 2 with a single pass CO 2 conversion efficiency of ~12%. Contact angle measurements reveal that npAu coatings provide a more hydrophobic electrode interface compared to MS Au coatings, suggesting that the more hydrophobic interfacial environment of npAu coatings helps mitigating electrode flooding which is associated with performance deterioration over time.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2024

Hierarchical Composites Patterned via 3D Printed Cellular Fluidics

Additive manufacturing of freeform structures containing multiple materials with deterministic spatial arrangement and interactions remains a challenge for most 3D printing processes, due to complex fabrication tool requirements and limitations in printability of some material classes. Here, in this paper, a versatile method is reported to produce architected composites using the concept of cellular fluidics, in which lattices of unit cells are used as templating scaffolds to guide flowable infill materials in a programmed spatial pattern, upon which they are cured in place to produce a deterministically ordered multimaterial solid. The lattice design relies on the unit cell size, type, strut diameter, surface wetting, and distribution of cellular structures to control liquid flow and retention. Individual unit cells are tuned to achieve reliable infilling and combined into higher-order architectures to achieve multiscale composite materials with disparate mechanical properties, including those considered non-printable. Lattice design considerations for leveraging capillary phenomena and demonstrate several methods of patterning polymers in 3D-printed cellular fluidic structures are presented. The concept of tuning the compressive response of an architected composite using a flexible-elastomer as the lattice and a stiff-epoxy as the infill material is illustrated.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Field‐representative evaluation of PID‐polarization in TOPCon PV modules by accelerated stress testing

Abstract Potential‐induced degradation‐polarization (PID‐p) can reduce module power, but how to project the extent to which PID‐p may occur in field conditions considering the factors of system voltage, condensed moisture, temperature, and illumination has not been clarified. Using tunnel oxide passivated contact (TOPCon) modules, this work demonstrates a method to test full‐size crystalline silicon PV modules for PID‐p to provide field‐representative results. In initial screening tests with positive or negative 1000 V electrical bias applied at 60°C for 96 h using Al foil electrodes on the glass surfaces, the module type exhibited reversible PID‐p only on the front face when the cell circuit was in negative voltage potential. No PID was detected on the rear after testing in either polarity. We then evaluated the PID‐p sensitivity on the front side under different UV irradiances while maintaining the glass surface wet to estimate real‐world susceptibility to PID‐p. The magnitude of the observed behavior was fit using a previously developed charge transfer and depletion by light model. Whereas power loss with −1000 V applied to the cell circuit at 60°C for 96 h in the dark was about 30%, testing the module front under 0.051 W·m −2 nm −1 at 340 nm UVA irradiation using fluorescent tubes, the mean degradation was only 3%. When the modules were tested in the dark for PID‐p with in situ dark current–voltage (I‐V) characterization, the thermal activation energy for degradation was 0.71 eV; for recovery in the dark, it was 0.58 eV. Whereas recovery from the degraded state at 60°C in the dark without voltage bias was 5% absolute in 38 h, rapid recovery of about 5% absolute was observed with 1000 W·s/m 2 exposure at 25°C using a flash tester.

14 SOLAR ENERGY↗
DOE OSTI2022

Development of an innovative process for post-combustion CO 2 capture to produce high-value NaHCO 3 nanomaterials

An innovative post-combustion process using aqueous sodium glycinates solutions (SGS) for CO 2 capture from a split flue gas stream emitted from the 600 MWe coal power plant, used in the Wolverine Clean Energy Venture (WCEV) project, was developed in Aspen Plus v.10. The flue gas flow rate used in the process was 12.43 kg/s (at 353.15 K and 101.33 kPa) and contained 0.0023 and 13.33 mol% of SO 2 and CO 2 , respectively. The overall process includes 5 main units designed to remove all SO 2 and capture more than 90 mol% of CO 2 in the flue gas stream, while producing high-value, salable sodium bicarbonate (NaHCO 3 ) nanomaterials to offset the total process costs. The hydraulics, mass transfer characteristics, and process performance obtained using Aspen Plus were discussed. Also, the capital expenditure (CAPEX), operating expenditure (OPEX), and Levelized cost of CO 2 capture (LCOC) were calculated to assess the feasibility of this process. Further, the hydraulics in the SO 2 washing and CO 2 capture units showed a pressure drop of 12 and 1 kPa, respectively, and the behaviors of the liquid holdup and normalized packing specific wetted surface area were similar in both units. The gas-side mass transfer coefficients were orders of magnitude greater than the liquid-side mass transfer coefficients. The process was able to capture 2.352 kg/s of CO 2 and produce 4.486 kg/s of valuable NaHCO 3 nanomaterials. Also, the calculated CAPEX, OPEX, and LCOC of the process for a 30-year plant lifetime were ($\$ $4,450,552), (233.00 $\$ $/h) and (35.49 $\$ $/ton of CO 2 captured), respectively.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Bioinspired design toward nanocellulose-based materials

Nature provides lots of inspiration for material and structural design for various applications. Deriving design principles from the investigation of nature can provide a rich source of inspiration for the development of multifunctional materials. The bioinspired design templates mainly include mussels, nacre, and various plant species. As a sustainable and renewable feedstock, nanocellulose can be used to fabricate advanced materials with multifunctional properties through bioinspired designs. However, challenges and opportunities remain for realizing the full potential in the design of novel materials. Here, this article reviewed recent development in the bioinspired nanocellulose based materials and their application. This article summarizes the functions (e.g., surface wetting) and applications (e.g., composite) of bioinspired nanocellulose-based materials. The bioinspired design templates are discussed along with strategies, advantages, and challenges to the development of synthetic mimics. Additionally, mechanisms and processes (e.g., chemical modification, self-assembly) leading to biomimetic design are discussed. Finally, future research directions and opportunities of bioinspired nanocellulose-based materials are highlighted.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Initial design concepts for solid boron injection in ITER

As part of ITER’s consideration to change its first wall material from beryllium to tungsten, the ITER Organization has proposed studying the feasibility of real-time solid boron injection (SBI) into the plasma to coat the walls and divertor to supplement glow discharge boronization (GDB). Boron deposits getter oxygen and reduce sputtering of tungsten from plasma facing components (PFCs). Particularly in areas with significant plasma wall interactions, boron coatings are expected to be short-lived under high performance plasma conditions. The proposed SBI system aims to maintain boron layers in these areas to avoid excessive radiation from tungsten in the plasma as a risk mitigation to ensure ITER will be able to reach and sustain Q = 10 conditions. The system will be used sparingly, as redeposition of boron can lead to significant tritium retention, which must be minimized in ITER to comply with nuclear safety concerns. SBI is proposed to limit and precisely control the amount of boron injected in real-time during plasma operation. Here, some of the design requirements and initial concepts for an SBI system in ITER are presented based on previous results carried out with SBI systems on a number of tokamaks and stellarators around the world. Previous results using SBI systems installed by PPPL have injected boron particles from 5 µm–2 mm diameter at calibrated rates of 2–200 mg/s in real-time during plasma operation on AUG, DIII-D, EAST, KSTAR, LHD, TFTR, WEST, and W7-X, leading to improved wall conditions with reduced plasma impurity concentrations and radiated power and improved plasma performance. The boron is ionized in the plasma edge and then deposited on plasma-wetted surfaces. On AUG, EAST and WEST reduced tungsten sputtering sources were observed following several discharges with SBI. Extrapolation of these SBI results are presented to estimate the amount of boron needed for wall conditioning in ITER. Real-time SBI control requirements and plasma operation scenarios for ITER are also described.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Design of a high-temperature cell for cobalt-60 irradiations of aqueous solutions with in situ UV–visible spectroscopy

To understand the speciation of solutes in aqueous solutions in high temperature radiation environments, we report the design and fabrication of a custom-built, high temperature (≤300 °C) titanium irradiation cell with in situ optical spectroscopy capabilities, as afforded by coupled fiber optic cables. The wetted surfaces of the 8-inch tall cylindrical cell with 3.5 in. diameter are entirely made of titanium, sapphire, and gold, which are chemically and radiolytically inert. The initial benchmarking results are reported, including the baseline spectrum of deionized water as a function of temperature, the stability of a spectrum over 4 h at 100 °C, and an irradiated Fricke dosimetry solution under ambient irradiator temperature conditions (27.0 ± 0.5 °C). Further, the average gamma radiation dose rate in the cell in its current configuration is 26.1 ± 1.3 Gy min -1 . This cell has application in studying several processes throughout the nuclear fuel cycle, including the reactor coolant behavior.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2022

Amyloid-like amelogenin nanoribbons template mineralization via a low-energy interface of ion binding sites

Protein scaffolds direct the organization of amorphous precursors that transform into mineralized tissues, but the templating mechanism remains elusive. Motivated by models for the biomineralization of tooth enamel, wherein amyloid-like amelogenin nanoribbons guide the mineralization of apatite filaments, we investigated the impact of nanoribbon structure, sequence, and chemistry on amorphous calcium phosphate (ACP) nucleation. Using full-length human amelogenin and peptide analogs with an amyloid-like domain, films of β-sheet nanoribbons were self-assembled on graphite and characterized by in situ atomic force microscopy and molecular dynamics simulations. All sequences substantially reduce nucleation barriers for ACP by creating low-energy interfaces, while phosphoserines along the length of the nanoribbons dramatically enhance kinetic factors associated with ion binding. Furthermore, the distribution of negatively charged residues along the nanoribbons presents a potential match to the Ca–Ca distances of the multi-ion complexes that constitute ACP. These findings show that amyloid-like amelogenin nanoribbons provide potent scaffolds for ACP mineralization by presenting energetically and stereochemically favorable templates of calcium phosphate ion binding and suggest enhanced surface wetting toward calcium phosphates in general.

59 BASIC BIOLOGICAL SCIENCES↗