Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “preform”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS2001

Microstructure and Tensile Properties of BN/SiC Coated Hi-Nicalon, and Sylramic SiC Fiber Preforms

Batch to batch and within batch variations, and the influence of fiber architecture on room temperature physical and tensile properties of BN/SiC coated Hi-Nicalon and Sylramic SiC fiber preform specimens were determined. The three fiber architectures studied were plain weave (PW), 5-harness satin (5HS) and 8-harness satin (8HS) Results indicate that the physical properties vary up to 10 percent within a batch, and up to 20 percent between batches of preforms. Load-reload (Hysteresis) and acoustic emission methods were used to analyze damage accumulation occurring during tensile loading. Early acoustic emission activity, before observable hysteretic behavior, indicates that the damage starts with the formation of nonbridged tunnel cracks. These cracks then propagate and intersect the load bearing "0" fibers giving rise to hysteretic behavior, For the Hi-Nicalon preform specimens, the onset of "0" bundle cracking stress and strain appeared to be independent of the fiber architecture. Also, the "0" fiber bundle cracking strain remained nearly the same for the preform specimens of both fiber types. Transmission Electron Microscope (TEM) analysis indicates that the Chemical Vapor Infiltration (CVI) Boron Nitride (BN) interface coating is mostly amorphous and contains carbon and oxygen impurities, and the CVI SiC coating is crystalline. No reaction exists between the CVI BN and SiC coating.

Bhatt, Ramakrishna T.↗
NASA NTRS2002

Microstructure and Tensile Properties of BN/SiC Coated Hi-Nicalon, and Sylramic SiC Fiber Preforms

Batch to batch and within batch variations, and the influence of fiber architecture on room temperature physical and tensile properties of BN/SiC coated Hi-Nicalon and Sylramic SiC fiber preform specimens were determined. The three fiber architectures studied were plain weave (PW), 5-harness satin (5HS), and 8-harness satin (8HS). Results indicate that the physical properties vary up to 10 percent within a batch, and up to 20 percent between batches of preforms. Load-reload (Hysteresis) and acoustic emission methods were used to analyze damage accumulation occurring during tensile loading. Early acoustic emission activity, before observable hysteretic behavior, indicates that the damage starts with the formation of nonbridged tunnel cracks. These cracks then propagate and intersect the load bearing "0 deg" fibers giving rise to hysteretic behavior. For the Hi-Nicalon preform specimens, the onset of "0 deg" bundle cracking stress and strain appeared to be independent of the fiber architecture. Also, the "0 deg" fiber bundle cracking strain remained nearly the same for the preform specimens of both fiber types. TEM analysis indicates that the CVI BN interface coating is mostly amorphous and contains carbon and oxygen impurities, and the CVI SiC coating is crystalline. No reaction exists between the CVI BN and SiC coating.

Bhatt, Ramakrishna T.↗
NASA NTRS2001

Apparatus and process for freeform fabrication of composite reinforcement preforms

A solid freeform fabrication process and apparatus for making a three-dimensional reinforcement shape. The process comprises the steps of (1) operating a multiple-channel material deposition device for dispensing a liquid adhesive composition and selected reinforcement materials at predetermined proportions onto a work surface; (2) during the material deposition process, moving the deposition device and the work surface relative to each other in an X-Y plane defined by first and second directions and in a Z direction orthogonal to the X-Y plane so that the materials are deposited to form a first layer of the shape; (3) repeating these steps to deposit multiple layers for forming a three-dimensional preform shape; and (4) periodically hardening the adhesive to rigidize individual layers of the preform. These steps are preferably executed under the control of a computer system by taking additional steps of (5) creating a geometry of the shape on the computer with the geometry including a plurality of segments defining the preform shape and each segment being preferably coded with a reinforcement composition defining a specific proportion of different reinforcement materials; (6) generating programmed signals corresponding to each of the segments in a predetermined sequence; and (7) moving the deposition device and the work surface relative to each other in response to these programmed signals. Preferably, the system is also operated to generate a support structure for any un-supported feature of the 3-D preform shape.

Yang, Junsheng↗
NASA NTRS2010

Methods for producing silicon carbide architectural preforms

Methods are disclosed for producing architectural preforms and high-temperature composite structures containing high-strength ceramic fibers with reduced preforming stresses within each fiber, with an in-situ grown coating on each fiber surface, with reduced boron within the bulk of each fiber, and with improved tensile creep and rupture resistance properties for each fiber. The methods include the steps of preparing an original sample of a preform formed from a pre-selected high-strength silicon carbide ceramic fiber type, placing the original sample in a processing furnace under a pre-selected preforming stress state and thermally treating the sample in the processing furnace at a pre-selected processing temperature and hold time in a processing gas having a pre-selected composition, pressure, and flow rate. For the high-temperature composite structures, the method includes additional steps of depositing a thin interphase coating on the surface of each fiber and forming a ceramic or carbon-based matrix within the sample.

DiCarlo, James A.↗
NASA NTRS2014

Methods for Producing High-Performance Silicon Carbide Fibers, Architectural Preforms, and High-Temperature Composite Structures

Methods are disclosed for producing architectural preforms and high-temperature composite structures containing high-strength ceramic fibers with reduced preforming stresses within each fiber, with an in-situ grown coating on each fiber surface, with reduced boron within the bulk of each fiber, and with improved tensile creep and rupture resistance properties tier each fiber. The methods include the steps of preparing an original sample of a preform formed from a pre-selected high-strength silicon carbide ceramic fiber type, placing the original sample in a processing furnace under a pre-selected preforming stress state and thermally treating the sample in the processing furnace at a pre-selected processing temperature and hold time in a processing gas having a pre-selected composition, pressure, and flow rate. For the high-temperature composite structures, the method includes additional steps of depositing a thin interphase coating on the surface of each fiber and forming a ceramic or carbon-based matrix within the sample.

DiCarlo, James A.↗
NASA NTRS2021

Melt Infiltration Studies of 2D Tyranno SA3(R) Ceramic Matrix Composite Preforms with CrSi2 Intermetallic Alloy

The present paper reports the results of melt infiltrating 2D Tyranno SA3@ fiber woven preforms with molten CrSi2 between 1768 and 1896 K under a vacuum of 1.3 x 10-4 Pa (10-6 torr). The infiltration times varied between 1800 and 7200 s, which did not have any significant effect on the volume fraction of voids filled with the metal. Optical and scanning electron microscopy, back scattered electron imaging, energy dispersion spectroscopy and Raman spectroscopy were used to characterize the infiltrated preforms. A plot of the volume fraction of open voids infiltrated against the absolute melt infiltration temperature showed a sharp peak at 1773 K with almost complete infiltration of the voids at this temperature. The extent of silicide infiltration of the preforms dropped steeply above 1773 K with increasing melt infiltration temperature irrespective of the amount of infiltration time. Above 1805 K, the volume fraction of voids infiltrated with the melt was nearly 0%. It is demonstrated that CrSi2 did not show evidence of a reaction with the SiC fibers. The possibility that a resisting force due to contact angle hysteresis (CAH) may have influenced the diminishing amount of voids filled with increasing temperature above 1773 K was examined. The resistance force was estimated to be extremely small to be consequential. Another possibility that the CrSi2 may have decomposed into Cr(g) and Si(g) in the vacuum melt infiltration furnace appeared to be more plausible based on thermodynamic analyses. An empirical equation is proposed to calculate the amount of remaining charge left to infiltrate the preforms at the infiltration temperature. It is shown that an initial charge of 10 g would rationalize the present observations. While the decomposition of the CrSi2 appeared to mostly explain the present results, some discrepancies were observed, which were inconsistent with the decomposition model.

CrSi2, chromium silicide, ceramic matrix composite↗
NASA NTRS2023

Dry Preform Stitching Using Temporary Vacuum Consolidation

Stitched composites (composite parts stitched in a dry preform state that are infused with resin and cured to a final shape) offer a variety of benefits for modern aircraft structures. In this document one means of stitching dry fabric preforms in a state of temporary vacuum consolidation is discussed. This vacuum consolidation allows for the completion of stitching procedures while the dry preform thickness is temporarily reduced to a thickness reflective of its final cured thickness. Here, a temporary vacuum consolidation process enabling stitching of preforms of unconsolidated nominal thickness greater than the maximum allowable stitching thickness for the Integrated Structural Assembly of Advanced Composite (ISAAC) system is explored as a use case for such processes. Temporary vacuum consolidation processes may lead to simplified manufacturing processes or desirable composite material properties in the future.

Stitched Composites↗
DOE OSTI2020

High-performance molded composites using additively manufactured preforms with controlled fiber and pore morphology

Here, large-scale multimaterial preforms produced by additive manufacturing (AM) underwent compression molding (CM) to produce high-performance thermoplastic composites reinforced with short carbon fibers. AM and CM techniques were integrated to control the fiber orientation (microstructure) and to reduce void content for the improved mechanical performance of the composite. The new integrated manufacturing technique is termed “additive manufacturing-compression molding” (AM-CM). For the present study, the most common materials were used for large-scale printing, i.e., acrylonitrile butadiene styrene (ABS), carbon fiber (CF)–filled ABS (CF/ABS) and glass fiber (GF)–filled ABS (GF/ABS). Three different manufacturing processes; (a) AM (b) extrusion compression molding (ECM), and (c) AM-CM were used to prepare four different panel configurations: (1) neat ABS, (2) CF/ABS, (3) overmold (CF/ABS over neat ABS), and (4) sandwich (neat ABS between two CF/ABS layers). The mechanical properties (tensile and flexural strength and modulus, and Izod impact energy) of samples prepared via all three manufacturing processes were compared. X-ray microcomputer tomography was employed to evaluate the fiber orientation distribution and the volumetric porosity content. The preform maintained high fiber alignment (≈ 82% of fibers within the range of 0–20° in the deposition direction), and the volumetric porosity was reduced by 50% from 3.79% to 1.91% after compression. The alignment of long pores along the deposition direction was also observed. The mechanical properties are discussed with correlation to the fiber alignment and void content in the samples. CF/ABS samples prepared by AM-CM showed significant improvement of 11.15%, 35.27%, 28.6%, and 74.3% in the tensile strength, tensile modulus, flexural strength, and flexural modulus, respectively, when compared with samples prepared by ECM. Unique aspects of this study are the demonstration of large-scale multimaterial AM and the use of multimaterials as preforms to make high-performance composites.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Microstructural and infiltration properties of woven preforms during chemical vapor infiltration

Interface-resolved direct numerical simulations (DNSs) of chemical vapor infiltration (CVI) have been performed over a range of furnace-operating conditions (Thiele moduli) and for practical woven preform geometries. A level-set method is used to resolve the geometry of the initial preform at tow scale. The interface between the vapor and solid phase is then evolved in time through the entire CVI densification cycle, fully resolving the time-varying topology between the two phases. In contrast to previous level-set methods for CVI simulation, the physical reaction and diffusion processes govern the level-set movement in the current approach. The surface deposition kinetics is described by the usual one-step model. In this paper, the DNS data are used to study the evolving porosity, surface-to-volume ratio, and flow infiltration properties (permeability and effective diffusivities). Additionally, comparisons are made to popularly-assumed structure functions and the standard, Kozeny–Carmen porous media model commonly employed in modeled CFD simulations of CVI. The virtual DNS experiments reveal a Thiele modulus and preform geometry (fabric layup) dependence which the existing microstructural and infiltration models are not able to describe throughout the entire densification process. The DNS-based, woven geometry-specific correlations can be applied directly to mean-field, furnace-scale CFD simulations.

36 MATERIALS SCIENCE↗
NASA NTRS1974

Study of glass preforms for glass fiber optics applications (study of space processing of ceramic materials)

The feasibility, and technical and economic desirability was studied of space processing of glass preforms for optical fiber transmission applications. The results indicate that space processing can produce glass preforms of equal quality at lower cost than earth bound production, and can produce diameter modulation in the glass preform which promotes mode coupling and lowers the dispersion. The glass composition can be modified through the evaporative and diffusion processes, and graded refractive index profiles can be produced. A brief summary of the state of the art in optical fiber transmission is included.

Wang, F. F. Y.↗
NASA NTRS1990

Observation of seeded second harmonic generation in bulk germanosilicate fiber preforms

Simultaneous irradiation of a bulk fiber preform with molar concentrations of 3 pct Ge and 0.5 pct P doped silica core region resulted in self-organized second harmonic generation with an effective chi(2) of about 1.2 x 10 to the -16th m/V. The experiments revealed that the bulk preform requires the same critical IR intensity (10 GW/sq cm) as the drawn fibers to prepare. Attempts to self-prepare the preform field, indicating that self-preparation in fibers is most likely initiated by second harmonic generation associated with the core-cladding interface.

Lawandy, N. M.↗
NASA NTRS1991

Structural mechanics of 3-D braided preforms for composites. IV - The 4-step tubular braiding

This paper presents the fundamentals of the 4-step 3D tubular braiding process and the structure of the preforms produced. Based on an idealized structural model, geometric relations between the structural parameters of the preform are analytically established. The effects of machine arrangement and operating conditions are discussed. Yarn retraction, yarn surface angle, outside diameter, and yarn volume fraction of the preform in terms of the pitch length, the inner diameter, and the machine arrangement are theoretically predicted and experimentally verified.

Hammad, M.↗
NASA NTRS1993

Advanced resin systems and 3D textile preforms for low cost composite structures

Advanced resin systems and 3D textile preforms are being evaluated at Lockheed Aeronautical Systems Company (LASC) under NASA's Advanced Composites Technology (ACT) Program. This work is aimed towards the development of low-cost, damage-tolerant composite fuselage structures. Resin systems for resin transfer molding and powder epoxy towpreg materials are being evaluated for processability, performance and cost. Three developmental epoxy resin systems for resin transfer molding (RTM) and three resin systems for powder towpregging are being investigated. Various 3D textile preform architectures using advanced weaving and braiding processes are also being evaluated. Trials are being conducted with powdered towpreg, in 2D weaving and 3D braiding processes for their textile processability and their potential for fabrication in 'net shape' fuselage structures. The progress in advanced resin screening and textile preform development is reviewed here.

Shukla, J. G.↗
NASA NTRS1995

Effects of preform architecture on modulus and strength of 2-D triaxially braided textile composites

Laminates formed using braided fibrous preforms have been extensively investigated during the course of the past few years as alternatives to unidirectional prepreg tape systems. This paper focused on one aspect of that work. It defined the role of the fibrous preform architecture in controlling a laminate's mechanical properties. The presentation was divided into four sections as the outline listed above illustrates. The presentation began with a brief introduction which defined the objectives of the study and detailed the materials studied. This was followed by a review of empirical test results. The materials' moduli and strengths were measured in both tension and compression. Their shear moduli were also experimentally determined. The review of the empirical data comprised the bulk of the presentation. A comparison of the experimental data to results predicted analytically was then presented. The presentation concluded with a few summary remarks. The specimens studied in this investigation featured 2-D triaxially braided AS4 graphite fiber preforms impregnated with Shell 1895 epoxy resin.

Masters, John E.↗
NASA NTRS1990

Converting a carbon preform object to a silicon carbide object

A process for converting in depth a carbon or graphite preform object to a silicon carbide object, silicon carbide/silicon object, silicon carbide/carbon-core object, or a silicon carbide/silicon/carbon-core object, by contacting it with silicon liquid and vapor over various lengths of contact time in a reaction chamber. In the process, a stream comprised of a silicon-containing precursor material in gaseous phase below the decomposition temperature of said gas and a coreactant, carrier or diluent gas such as hydrogen is passed through a hole within a high emissivity, thin, insulating septum into the reaction chamber above the melting point of silicon. The thin septum has one face below the decomposition temperature of the gas and an opposite face exposed to the reaction chamber. Thus, the precursor gas is decomposed directly to silicon in the reaction chamber. Any stream of decomposition gas and any unreacted precursor gas from the reaction chamber is removed. A carbon or graphite preform object placed in the reaction chamber is contacted with the silicon. The carbon or graphite preform object is recovered from the reactor chamber after it has been converted to a desired silicon carbide, silicon and carbon composition.

Levin, Harry↗
DOE OSTI2022

Reinforced preform and method for molding

A reinforced preform includes a sheet of reinforced material having opposed first and second edges, with each edge having a respective first connection point located therealong. The preform also includes first and second tethers, with each tether being attached at a respective first end thereof to a respective one of the first connection points and having a respective second end thereof terminating in at least one of: a respective loop tied at the respective second end, a respective knot tied at the respective second end, a respective graspable member to which the respective second end is connected, and an attachment to a respective second connection point located along a perimeter of the sheet. A method and mold for molding a reinforced preform are also disclosed.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Composite components and methods of manufacturing composite components using magnetic forces at fiber preform seams

A method of manufacturing a composite component according to various aspects of the present disclosure includes disposing a fiber preform in a mold. The fiber preform includes a first portion having a first edge and a second portion having a second edge. The first edge and the second edge cooperate to at least partially define a gap. One of the first portion or the second portion includes a first ferromagnetic material and the other of the first portion or the second portion includes a first magnetic or magnetizable component. The method further includes closing the gap by generating a magnetic field from the first magnetic or magnetizable component. The method further includes injecting a polymer precursor into the mold. The method further includes forming the composite component by solidifying the polymer precursor to form a polymer. The composite component includes the fiber preform and the polymer.

Aitharaju, Venkateshwar R.↗
DOE OSTI2023

A Level Set Model for Structured Mesh Representation of Fibrous Preforms used in Composites Manufacturing

Here, a model for implicit representation of fibrous and woven preforms used for composites manufacturing is described. The method is based on a level set function defined on a structured mesh to implicitly capture the complex fiber and weave geometries. Since most software packages used to model woven preforms are based on unstructured mesh, a numerical model for transforming a discretized surface to a structured mesh representation and vice-a-versa is presented. Specific emphasis is on scalable computation of a level set function for large and complex 3D woven structures from a triangulated surface of the smallest unit (yarn). The model is applied to capture a periodic 3D layered 5-harness satin (5HS) weave geometry on a structured mesh. Geometric transformations needed to efficiently compute the level set function for the 3D structure on a high resolution mesh are described. Effects of mesh resolution on the geometric features such as number of resolved fibers, effective fiber size, and the surface area to volume ratio of the iso-surface are analyzed. Using the distance property of the level set function, an approach to evaluate the structure function resulting from transient evolving topology representing densification due to matrix phase depositions is also presented. The approach captures transition of the geometric characteristic from fiber governed at early stages of densification to yarn governed at the terminal stage.

36 MATERIALS SCIENCE↗