Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “oven”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Adaptively controlled fast production of defect-free beryllium ion crystals using pulsed laser ablation

Trapped atomic ions find wide applications ranging from precision measurement to quantum information science and quantum computing. Beryllium ions are widely used due to the light mass and convenient atomic structure of beryllium; however, conventional ion loading from thermal ovens exerts undesirable gas loads for a prolonged duration. Here, we demonstrate a method to rapidly produce pure linear chains of beryllium ions with pulsed laser ablation, serving as a starting point for large-scale quantum information processing. Our method is fast compared to thermal ovens, reduces the gas load to only 10 -12 Torr (10 -10 Pa) level, yields a short recovery time of a few seconds, and also eliminates the need for a deep ultraviolet laser for photoionization. We also study the loading dynamics, which show non-Poissonian statistics in the presence of sympathetic cooling. In addition, we apply feedback control to obtain defect-free ion chains with desirable lengths.

47 OTHER INSTRUMENTATION↗
DOE OSTI2025

Impact of window temperature variations on ITER toroidal interferometer and polarimeter (TIP) measurements

Abstract The toroidal interferometer and polarimeter (TIP) is one of the primary electron density diagnostics on ITER. To meet measurement requirements over several thousand seconds, environmental factors such as changes in the window temperature, air temperature, and humidity, which can cause uncompensated phase drifts, must be minimized. This paper reports measurements of the phase shift induced by ZnSe and BaF₂ windows as their temperature is varied utilizing the TIP prototype. To accomplish these measurements, test pieces of BaF₂ and ZnSe are placed in a small oven that is located in one leg of the 10.59/5.22 micron two-color interferometer TIP prototype. The oven temperature was varied from room temperature to ∼90 °C, which is slightly higher than the expected window temperatures on ITER. The vibration compensated phase shifts measured for these two materials are dϕᵥ꜀ /dT/L = 0.0121 and −0.275 deg. /°C/cm −1 for BaF₂ and ZnSe, respectively. From these measurements, it was concluded that temperature variations of the environmental/secondary confinement barrier window and primary vacuum window have to be suppressed within approximately 1°C and 2°C, respectively, in order to passively meet the electron density measurement requirements in ITER.

Akiyama, T (ORCID:0000000198469795)↗
DOE OSTI2021

Temperature dependence of viscoelastic Poisson’s ratio of cement mortar

Abstract Concrete creep research has focused primarily on uniaxial response. However, biaxially prestressed concrete structures are common, resulting in a multiaxial stress state that can complicate the behavior of a viscoelastic material like concrete. Significant creep strains may be induced in directions transverse to each principle stress due to Poisson’s effect. Past research is unclear regarding the viscoelastic or viscoplastic properties of concrete outside of uniaxial response. It has been reported in separate studies that concrete viscoelastic/viscoplastic Poisson’s ratio (VPR) is an increasing, decreasing and constant function with time, with all reported measurements performed at room temperature. In this paper, the 3D basic creep response of mature cement mortar is examined using a confined compression experiment that allows direct determination of the full stress and infinitesimal strain tensors in a single test, which enables the determination of VPR under a multiaxial stress state. For this purpose, a unique, miniature version of the standardized concrete creep frame is designed that is amenable to placing in climate chambers and temperature ovens. The experimental results indicate that the VPR of sealed, mature cement mortar is nearly constant and equal to the elastic at room temperature, while the VPR gradually increases with time when measured at 60 °C.

Construction & Building Technology↗
DOE OSTI2021

Design and Initial Verification Testing of an In Situ Load Retention Aging Fixture

Load retention is a key metric used to evaluate long-term mechanical functionality of polymeric materials. Its measurement currently requires periodically removing the aging fixtures from the ovens, removing the specimens from the fixtures, and performing load testing on the specimens. The ability to perform load measurement in situ (i.e., without having to remove the specimens from the fixtures, and possibly even the ovens) would facilitate data acquisition/analysis, improve data quality, and enable uninterrupted compression of specimens which is more representative of the actual application.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effective Kitchen Ventilation for Healthy Zero Net Energy Homes with Natural Gas

Past studies indicate that kitchen ventilation that minimally complies with California’s Residential Building Code is inadequate at controlling combustion pollutants from natural gas burners and particulate matter produced during cooking. Effectiveness is further limited by misperceptions that kitchen ventilation is infrequently needed. This project developed the technical basis for updating kitchen ventilation requirements to protect health in new California homes, especially in smaller homes common among low-income renters. Tasks included (1) a field study of ventilation equipment performance and indoor air quality in 23 low-income apartments at four sites; (2) analysis of range hood use related to cooking time and household parameters using data from 54 houses and 17 low-income apartments; (3)a measurement-based study to quantify performance of over-the-range microwave ovens with integrated exhaust fans;and (4) pollutant exposure simulations to inform capture efficiency standards.The field study found operational deficiencies with mechanical ventilation systems in a substantial fraction of low-income apartments that affected performance, resulting in higher exposures to pollutants generated indoors. Using gas cooking burners produced high short-term and weekly time-averaged nitrogen dioxide in apartments.Range hoods were used more frequently with cooking in houses (36percent) than apartments (28percent); use increased with overall cooking frequency in a home and with duration of cooktop but not oven events; actual use was correlated to, but lower than,self-reported use;and use was more frequent in houses when cooking generated any fine particulate matter (PM2.5)or when high PM2.5resulted from cooking in apartments. Performance of over-the-range microwaves with integrated exhaust fans was similar to that of range hoods of comparable price. Simulation analysis found that performance standards need to be updated to ensure that kitchen exhaust ventilation adequately protects for substantial cooking in new California residences.

03 NATURAL GAS↗
DOE OSTI2026

Dielectric Spectroscopy Cable NDE for Unequal Aging Over Different Lengths

This Pacific Northwest National Laboratory milestone report assesses the effect of unequal aging over different lengths of cable on dielectric spectroscopy (DS) bulk impedance measurements from the cable end. DS measurements can indicate the remaining useful life of cables; however, most benchmark tests are based on accelerated aging of the entire cable. If only a portion of the cable is exposed to a harsh environment (as is frequently the case), the DS measurement will indicate a significantly less-aged cable than if the entire cable were exposed to a uniform environmental stress. The DS measurement is primarily related to the intrinsic insulation material relative permittivity—typically between 1.5 and 3.0. Insulation aging increases permittivity and, correspondingly, the cable’s overall capacitance measured from the cable end. To judge the health of the overall cable system, operators are primarily interested in the condition of the most severely aged section since that is where a failure is most likely to occur. This can be expressed as the dimensionless relative permittivity of the severely aged section divided by the permittivity of a pristine cable. This relative permittivity is an intrinsic material parameter independent of cable length and can serve as a quantitative indication of the insulation condition. If the relative percentages of cable exposed to a harsh and benign environment are known, the DS measurement of the entire cable length, including both pristine and aged sections, can be compensated to predict the relative permittivity (relative to pristine permittivity) of the most severly aged segment. A test was performed on three 50 ft (16 m) cables with 10%, 50%, and 90% of the cable inside a thermal aging oven. Predictably, the aging effect on the DS response was greatest in the 90% sample, followed by the 50% sample, and then the 10% sample. The more interesting result is the ratio of the aged insulation permittivity to the pristine insulation permittivity. Based on prior work, an end-of-life cable has a value of approximately 1.35. If the relative percentages of pristine and severely aged cable lengths are known, and the total cable-length capacitance of the initial pristine cable and the combined pristine plus aged cable are known, the relative aged permittivity (ratio of aged section permittivity / pristine section permittivity) can be estimated. The relative cable lengths exposed to a harsh environment may be known or estimated based on plant layout drawings or cable reflectometry tests that can locate the oven entry and exit points. The compensation was verified using a lumped-parameter model to predict the aged-segment permittivity e2/e1, where e2 is the aged-segment permittivity and e1 is the pristine-segment permittivity. For all three percentages of aged cable lengths, the ratio was quite similar, as would be expected since all cable segments were exposed to the same aging environment. This ratio of aged permittivity to pristine permittivity can be compared to other damage indicating tests, including elongation at break, to assess cable condition.

ARENA Test Bed↗
DOE OSTI2020

Factors Impacting Range Hood Use in California Houses and Low-Income Apartments

Venting range hoods can control indoor air pollutants emitted during residential cooktop and oven cooking. To quantify their potential benefits, it is important to know how frequently and under what conditions range hoods are operated during cooking. We analyzed data from 54 single family houses and 17 low-income apartments in California in which cooking activities, range hood use, and fine particulate matter (PM 2.5 ) were monitored for one week per home. Range hoods were used for 36% of cooking events in houses and 28% in apartments. The frequency of hood use increased with cooking frequency across homes. In both houses and apartments, the likelihood of hood use during a cooking event increased with the duration of cooktop burner use, but not with the duration of oven use. Actual hood use rates were higher in the homes of participants who self-reported more frequent use in a pre-study survey, but actual use was far lower than self-reported frequency. Residents in single family houses used range hoods more often when cooking caused a discernible increase in PM 2.5 . In apartments, residents used their range hood more often only when high concentrations of PM 2.5 were generated during cooking.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2023

MEASURING THERMALLY-INDUCED DISTORTION OF LARGE-SCALE COMPOSITE PRINTED STRUCTURES USING DIGITAL IMAGE CORRELATION

Additive manufacturing (AM) gives designers the ability to create complex part geometries without several of the limitations of traditional manufacturing. Large-Scale AM (LSAM) allows the creation of large composite structures and is a popular area of composite tooling research. Fiber-reinforced polymers are common feedstock for LSAM tooling but introduce anisotropic thermomechanical properties that can lead to the warpage of tools at autoclave conditions. Digital image correlation (DIC) has been used to measure the coefficient of thermal expansion (CTE) of LSAM parts using a novel DIC Oven design. This method was utilized to measure the CTE of LSAM structures printed using different fiber-reinforced materials and multiple geometries. Specifically, glass fiber ABS (GF-ABS) and carbon fiber ABS (CF-ABS) samples were compared as well as cube and plate geometries for each material. The temperature profile over time was also evaluated to determine how rapidly the strain of the sample increased as temperature of the DIC Oven was increased. A thermal model was developed to predict temperature profiles for various samples and identify when the samples had reached thermal equilibrium.

Corum, Tyler↗
DOE OSTI2023

Experimental and computational design tools for industrial drying processes: Challenges in process‐limit prediction

Abstract The coating and drying of inks and slurries are important steps to manufacture a plethora of products. Drying processes, particularly, comprise energy‐intensive steps that affect product cost and quality. Prior work has highlighted failures of various multicomponent diffusivity models to conserve mass in dryer modeling and challenges in predicting process limits given variability in published values of key thermodynamic parameters. Herein, we develop a computational model and benchtop drying experiments to investigate these concerns for drying polymer‐laden coatings. Model predictions of process limits in a single‐zone drying oven demonstrate that published variability in Flory–Huggins parameter yields large variations in predicted operating temperatures above which blistering occurs. This indicates that caution should be exercised when choosing approaches to obtain or predict the Flory–Huggins parameter, and that both benchtop drying experiments and a set of additional experiments, such as sorption experiments, are needed to fully characterize and optimize a given drying process.

Parrish, Chance↗
DOE OSTI2025

Cleavable Strand‐Fusing Cross‐Linkers as Additives for Chemically Deconstructable Thermosets with Preserved Thermomechanical Properties

Abstract Permanently cross‐linked polymer networks—thermosets—are often difficult to chemically deconstruct. The installation of cleavable bonds into the strands of thermosets using cleavable comonomers as additives can facilitate thermoset deconstruction without replacement of permanent cross‐links, but such monomers can lead to reduced thermomechanical properties and require high loadings to function effectively, motivating the design of new and optimal cleavable additives. Here, we introduce “strand‐fusing cross‐linkers” (SFCs), which fuse two network strands via a four‐way cleavable cross‐link. SFCs enable deconstruction of model polydicyclopentadiene (pDCPD) thermosets with as little as one‐fifth of the molar loading needed to achieve deconstruction using traditional cleavable comonomers. SFCs function under traditional oven curing as well as low‐energy frontal ring‐opening metathesis polymerization (FROMP) conditions and lead to improved thermomechanical properties, for example, glass transition temperatures, compared to prior cleavable comonomer designs. This work motivates the development of increasingly improved cleavable additives to enable thermoset deconstruction without compromising material performance.

Zhang, Shuyi [Department of Chemistry Massachusett↗
DOE OSTI2025

Cleavable Strand‐Fusing Cross‐Linkers as Additives for Chemically Deconstructable Thermosets with Preserved Thermomechanical Properties

Abstract Permanently cross‐linked polymer networks—thermosets—are often difficult to chemically deconstruct. The installation of cleavable bonds into the strands of thermosets using cleavable comonomers as additives can facilitate thermoset deconstruction without replacement of permanent cross‐links, but such monomers can lead to reduced thermomechanical properties and require high loadings to function effectively, motivating the design of new and optimal cleavable additives. Here, we introduce “strand‐fusing cross‐linkers” (SFCs), which fuse two network strands via a four‐way cleavable cross‐link. SFCs enable deconstruction of model polydicyclopentadiene (pDCPD) thermosets with as little as one‐fifth of the molar loading needed to achieve deconstruction using traditional cleavable comonomers. SFCs function under traditional oven curing as well as low‐energy frontal ring‐opening metathesis polymerization (FROMP) conditions and lead to improved thermomechanical properties, for example, glass transition temperatures, compared to prior cleavable comonomer designs. This work motivates the development of increasingly improved cleavable additives to enable thermoset deconstruction without compromising material performance.

Zhang, Shuyi [Department of Chemistry Massachusett↗
DOE OSTI2020

Fluorine-Free Superhydrophobic Coatings: Rapid Fabrication and Highly Efficient Oil/Water Separation

In this work, a rapid method is demonstrated to obtain a fluorine-free superhydrophobic/superoleophilic coating by a simple two-step method: dip-coating and oven curing. The chemical structure of the coating is based on the crosslinking reaction of an alkyl methacrylate, a dimethacrylate (crosslinker) and a silane (adhesive), using AIBN as initiator, toluene as solvent, and silica nanoparticles to enhance surface roughness. Chemorheology results show that the coating is fully cured even in 20 min at 100 °C, exhibiting a water contact angle (CA) of 162 ± 2°, sliding angle (SA) of 4 ± 1°, nanometrical structures throughout the surface, and excellent adhesion properties for the mesh screen. The coating exhibits outstanding oil/water separation efficiency (96–99%) for seven different types of oil (gasoline, diesel, petroleum ether, hexane, toluene, chloroform, and dichloromethane), and in addition presents high recyclability. Based on nonisothermal TGA, the activation energy of degradation, calculated using the Kissinger and Ozawa models, is 113.5 and 114 kJ mol -1 , respectively. Finally, the coating is thermally aged at 150 °C: the CA exhibits a smooth decrease up to 129 ± 1° at 120 min, and FTIR analysis shows structural changes possibly related to the generation of thermal oxidation products.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Large-scale additive manufacturing of self-heating molds

Large-scale material extrusion additive manufacturing technology is becoming the new mainstream technology for scaled-up composite mold and die applications. This paradigm shift in composite processing technology is primarily driven by out-of-autoclave tooling applications, in which fiber reinforced composite molds with scaled-up sizes and embedded heating elements are attractive. The present research describes the design, manufacturing, and testing of self-heating composite molds fabricated via a large-scale pellet extrusion 3D printing machine with an integrated wire co-extrusion tool. Polycarbonate (PC) composites reinforced with carbon fiber (PC/CF; 20 wt.%) and glass fiber (PC/GF; 20 wt.%) were used to fabricate mold parts. Joule heating thermal test results showed that uniform temperatures (~100 °C) were achieved for both PC/CF and PC/GF mold surfaces, using a custom-made feedback control power supply and infrared thermography. Mechanical characterizations, including tensile and flexural testing were performed on the wire-embedded and un-wired PC/CF and PC/GF base specimens to investigate the impact of the fiber reinforcement as well as the embedded wires. In the direction of extrusion, the ultimate tensile stress of PC/CF was 105 MPa, and that of PC/GF was 73 MPa, while the neat PC value was 64 MPa. Inner-bead voids and interfacial gaps were observed and characterized via optical and scanning electron microscopy. The embedded wires and inner bead impacted the mechanical properties of the composites. Furthermore, the stiffness of the wire-embedded mold was still satisfactory, proving that the technology can be used to fabricate additively manufactured out-of-oven/autoclave molds.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Comparison of the efficacy of a biocompatible and a distillable solvent for pretreatment of mixed bioenergy feedstocks

Biomass deconstruction is a crucial step in the production of lignocellulosic biofuels and bioproducts. However, identifying and selecting an optimal pretreatment solvent that enhances enzymatic saccharification while being cost-efficient and ensuring sustainability remains a challenge. In this study, we compare the effectiveness of the biocompatible ionic liquid cholinium lysinate ([Ch][Lys]) against the distillable solvent ethanolamine, when used for the pretreatment of mixed bioenergy feedstocks, including poplar, switchgrass, and sorghum. [Ch][Lys] was used at a concentration of 10 % wt. in a one-pot configuration without biomass washing and ethanolamine was used in a concentrated form and removed with a vacuum oven, before performing enzymatic hydrolysis and microbial conversion. Our results show that ethanolamine pretreatment consistently enhances the glucose yield across various biomass types compared to [Ch][Lys], with improvements ranging from 22.0 % to 52.7 %. The highest combined sugar release was observed when the three feedstocks were combined in equal amounts and pretreated with ethanolamine, achieving a glucose yield of 84.6 % and a xylose yield of 76.6 %. Additionally, ethanolamine exhibited exceptional solvent recovery efficiency, with removal efficiencies exceeding 99.8 % at 120 °C across all feedstocks, highlighting its advantage over non-distillable solvents. While both solvents produced biocompatible hydrolysates, the hydrolysates prepared using ethanolamine resulted in higher bioproduct formation. These findings highlight the industrial relevance of selecting recyclable and biocompatible solvents for scalable, sustainable, and cost-effective bioenergy production. This study contributes to the development of economically viable and scalable pretreatment technologies for bioenergy applications using different feedstocks and process configurations.

Rahman, Maksudur↗
DOE OSTI2022

Effects of edge-seal design on the mechanical and thermal performance of vacuum-insulated glazing

Although vacuum-insulated glazing (VIG) has been proposed as a promising solution towards developing energy-efficient buildings, VIGs have not become popular in the market due to several technical challenges including the complexity of the fabrication process. In particular, the edge-seal is a key component that significantly affects the thermal insulation and mechanical performance, and the development of edge-seal with adequate thermal insulation, mechanical strength, and reasonable processing cost is essential to overcome such technical issues in VIG. For this purpose, effects of edge-seal design parameters on the VIG performance should be identified. In this research, we analyzed the edge-seal for thermal transport as well as structural stresses to study the effects, and then identified and evaluated the material mixes for the edge-seal requirements. Here, the finite element simulations showed the significance of VIG corner calculation on overall thermal transmittance and the importance of seal conductivity below 1 W/m.K. The experiments with the flexible seals with different ratios of fine glass powder demonstrated that the measured shear strength values for the seal with less than 30% glass powder were more than 10 times larger than the calculated shear stress values. Based on these simulation and experimental results, a flexible sealant was developed using a proprietary mix of ceramic materials that meets the requirements of the designed VIG edge-seal, including structural as well as thermal stress resistance and a low conductivity. Moreover, the sealant is self-curing under atmospheric conditions, and thus it does not require costly inline process of laser curing or oven baking.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2021

Quantifying the chemical, electrochemical heterogeneity and spatial distribution of (poly) sulfide species using Operando SANS

In-situ and operando measurements are done to gain a better understanding of the precipitation mechanisms during charge and discharge in lithium sulfur batteries. A carbon felt networked with microfibers consisting of pores, 2 nm and smaller, is used as a freestanding sulfur host. Three different methods of sulfur infiltration are explored in order to determine the best one to fill most of the pores. It was identified to be a melt infiltration method in a vacuum oven, where the pores including the ultra-micropores, are successfully filled. In-situ electrochemical impedance spectroscopy measurements show a solid product formation occurring at the sulfur cathode, both during the high voltage plateau and at the end of discharge. In a 3-electrode EIS measurement, a similar solid product formation on the Li counter electrode due to its reaction with polysulfides is also observed. Operando small angle neutron scattering measurements show the solid product formation, in the carbon, both near the beginning and at the end of discharge, confirming the precipitation data via contrast changes as a function of charge and discharge. It is shown that Li 2 S precipitates in the pores at the beginning and the end of discharge, whereas S8 precipitates on the surface of the carbon felt. Finally, this lithium sulfur system shows both the quasi-solid-state and the solid-liquid-solid reactions in a typical ethereal electrolyte solution with a two-plateau discharge profile.

25 ENERGY STORAGE↗
DOE OSTI2022

Experimental screening of salt hydrates for thermochemical energy storage for building heating application

The selection of a suitable salt hydrate for use in a thermochemical energy storage system is challenging. In this work, the most promising salts to store intermediate heat energy were selected and tested. The criteria set are; volumetric energy density of >500 kWh m-3 with a dehydration temperature of <100 degrees C, material cost of <3.5 USD kg-1 (<15 USD kWh-1), melting does not occur during dehydration and safety. Based on that, the salt hydrates SrCl 2 , MgSO 4 , Na 3 PO 4 , MgCl 2 and SrBr 2 were selected and tested experimentally. A constant temperature and humidity chamber was used to measure moisture sorption of different salts. The hydration is investigated under the conditions of 20 degrees C and 20, 30, 40, 60 and 80% RH, while dehydration is investigated under the conditions of 70, 100 and 140 degrees C using an oven. These dehydration temperatures of <100 degrees C are suitable for solar application whereas the dehydration temperature of 140 degrees C is suitable for waste heat. Furthermore, the salts are cycled over 30 times under the hydration conditions of 20 degrees C, 60% RH with a dehydration temperature of 100 degrees C. From these results, it is concluded that SrCl 2 and SrBr 2 are the most promising salts. This study outlines both the advantages and disadvantages of each salt and states the conditions they are most suitable for.

25 ENERGY STORAGE↗
DOE OSTI2020

Economic and environmental impacts of a non-traditional combined heat and power system for a discrete manufacturing facility

Combined heat and power (CHP) is an electricity generation strategy that benefits all sides with a vested interest in the nations’ energy future. The technology allows for the efficient production of electricity and heat, which in turn reduces the carbon footprint and energy costs of a facility with significant heat and electricity loads. This paper investigates, through a detailed dynamic simulation, how a highly non-traditional CHP facility can leverage those forces to economically and environmentally benefit. Four system configurations of a composites manufacturing facility, one existing and three proposed systems, including two CHP configurations and one combined cooling, heating, and power (CCHP) configuration are evaluated from both economic and environmental views. The three proposed configurations are based on a 600 kW microturbine as the primary mover. The dynamic model showed great potential to capture the dynamics of the system configurations including the dynamics of temperature, oven exhaust fraction, electrical efficiency, and overall efficiency of the system configurations. All 3 CHP systems have a payback period between 8.03 and 8.33 years. The proposed system configurations reduce up to 22.7% of the CO 2 emission compared to the existing facility, supplying the demands in a cleaner manner.

42 ENGINEERING↗