Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “microwave heating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Microwave-Driven Nonoxidative and Selective Conversion of Methane to Ethylene over Mn-Based Catalysts

Recent advancements in microwave-driven nonoxidative catalytic synthesis of C 2 H 4 from CH 4 coupling offer a promising, energy-efficient, and eco-friendly alternative to conventional methods, where selective heating under microwave irradiation enables comparable conversions at substantially lower bulk temperatures and shorter reaction times. This study explores the performance of an MnO X -based catalyst supported on CeO 2 and HY zeolite (silica-toalumina ratio = 5.1) for the nonoxidative coupling of CH 4 (NOCM) under microwave irradiation. Inspired by the well-established efficacy of MnO X catalyst in oxidative CH 4 coupling (OCM), their application in NOCM has also shown significant performance. The catalytic system achieved 15% CH 4 conversion and 99% selectivity toward C 2 hydrocarbons and maintained 64% selectivity toward C 2 H 4 surpassing the yields reported in the literature even at higher temperatures (700−1000 °C). Catalyst performance was correlated with measurements by in situ Raman spectroscopy, and additional characterizations were performed using H 2 −temperature programmed reduction , NH 3 −temperature programmed desorption, and BET surface area analysis to understand structural changes during the reactions. These findings suggested that Mn functions as active sites for CH 4 activation in nonoxidative environments while also promoting efficient C−C coupling under microwave irradiation.

Catalysts↗
DOE OSTI2024

Microwave Absorbing Perovskite Catalysts for Efficient Electrification of Syngas Production from CO2 and Methane

Microwave absorbing catalysts have the potential to make thermal reactions such as methane reforming (CH4 + CO2 + H2O → H2 + CO) into carbon negative processes when coupled with decarbonized electricity. Due to microwaves directly heating the catalyst rather than heating the reactor and gases, even high temperature reactions such as dry reforming methane (DRM, CH4 + CO2 → H2 + CO) can be achieved rapidly, efficiently, and on-demand, ideal for coupling with intermittent renewable electricity. However, microwave catalysts present unique design challenges due to the same material needing to both efficiently absorb microwaves in oxidative and reductive reaction conditions and be an efficient and stable catalyst in inherently non-isothermal reactors. We screened from over 28 catalysts in the La0.8Sr0.2(Co-Ni-Mn)O3 perovskite solid-solution family to determine promising microwave reforming catalysts and identify design principles for effective materials. The best performing catalyst candidate was able to produce syngas ratios (H2:CO) from 1-3, and scale up testing showed CO and H2 production efficiencies rivaling conventional carbon intensive steam reforming efficiencies at the liters per minute level of production.

Marin, Christopher↗
DOE OSTI2026

Two-Way Coupled CFD/DEM Simulation of Electromagnetic Heating in a Fluidized Bed Reactor - Extended Abstract

A set of tools has been developed to couple a multiphase reacting computational fluid dynamics solver (MFIX) with two computational electromagnetic solvers (COMSOL and Elmer). In contrast to several recent investigations, which calculate a single static EM field prior to the CFD calculation, in the present work the electromagnetic field is periodically updated during the simulation. This enables the EM field and associated EM heating predictions to reflect the effects of evolving material properties (temperature, composition, size etc.) and the evolving distribution of material in the system. The present work uses effective medium theory (EMT) for the electromagnetic field calculations since the goal is to apply the tool for industrial scale reacting systems. Predictions using MFIX/COMSOL and MFIX/Elmer are compared to in bed thermocouple measurements from a fluidized bed experiment and recent simulation predictions and recent experiments performed at NETL. The NETL experiments also include packed bed operating conditions. Coupled MFIX/COMSOL simulations at these conditions are compared with similar simulations using only COMSOL to measure errors due to the solver coupling approach.

CFD↗
DOE OSTI2026

Two-Way Coupled CFD/DEM Simulation of Electromagnetic Heating in a Fluidized Bed Reactor

A set of tools has been developed to couple a multiphase reacting computational fluid dynamics solver (MFIX) with two computational electromagnetic solvers (COMSOL and Elmer). In contrast to several recent investigations, which calculate a single static EM field prior to the CFD calculation, in the present work the electromagnetic field is periodically updated during the simulation. This enables the EM field and associated EM heating predictions to reflect the effects of evolving material properties (temperature, composition, size etc.) and the evolving distribution of material in the system. The present work uses effective medium theory (EMT) for the electromagnetic field calculations since the goal is to apply the tool for industrial scale reacting systems. Predictions using MFIX/COMSOL and MFIX/Elmer are compared to in bed thermocouple measurements from a fluidized bed experiment and recent simulation predictions and recent experiments performed at NETL. The NETL experiments also include packed bed operating conditions. Coupled MFIX/COMSOL simulations at these conditions are compared with similar simulations using only COMSOL to measure errors due to the solver coupling approach.

CFD↗
DOE OSTI2025

Microwave-assisted delignification for improved cellulose production

This study aims to develop microwave (MW) technologies to improve the paper pulping process, decreasing both chemical and thermal energy requirements. The overall objective is to explore an efficient process that aids in the delignification of paper pulp, reducing energy needs and chemical intensity. The experimental variables evaluated during the MW-assisted digestion process include formic acid concentration, time, temperature, digestion cycles, and the formic acid to paper ratio. This research investigates the potential of MW technology to create a more sustainable and efficient cellulose production method.

microwave heating↗
DOE OSTI2026

Recycling of Printed Circuit Boards to Recover Critical Materials

The printed circuit board (PCB), a central component of most electronic devices, represents a significant fraction of the electronic product waste stream. The complex composition of PCBs, consisting of metals, polymers, and fiberglass, requires specialized recovery steps to reclaim valuable and critical materials and the safe disposal of brominated compounds. In this review paper, we describe the current state of critical material recovery and traditional recycling technologies and identify key obstacles to large-scale implementation. Metals present at high concentrations, such as copper, lead, and iron, are conventionally recovered from PCBs using hydrometallurgical, pyrometallurgical, or electrometallurgical processes. Hydrometallurgical methods achieve high selectivity through chemical leaching but pose significant challenges for effluent and reagent recovery. Pyrometallurgical methods facilitate rapid metal separation through smelting but require substantial energy and may release harmful gases. Electrometallurgical techniques produce high-purity metals but are constrained by pretreatment requirements and the consumption of energy. The non-metallic fraction of PCB waste is recycled using thermochemical conversion, microwave-aided heating, and direct recycling of epoxy–fiberglass composites, enabling material or energy recovery. The recovered polymer from direct recycling may have reduced mechanical strength and poor compatibility with new polymer matrices, and the resulting products from the thermal conversion suffer from incomplete conversion, degradation of quality, and residual contamination, as compared to synthetic polymers. Recent process developments have focused on extracting rare earth and supply-critical materials present at lower concentrations in the waste stream. The literature on existing and emerging approaches for recycling PCB wastes is reviewed to identify sustainable, economically viable, and environmentally responsible strategies for the recovery and reuse of critical materials from waste streams.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Relithiation process for direct regeneration of cathode materials from spent lithium-ion batteries

A method for the regeneration of cathode material from spent lithium-ion batteries is provided. The method includes dissolving a lithium precursor in a polyhydric alcohol to form a solution. Degraded cathode material containing lithium metal oxides are dispersed into the solution under mechanical stirring, forming a mixture. The mixture is heat treated within a reactor vessel or microwave oven. During this heat treatment, lithium is intercalated into the degraded cathode material. The relithiated electrode material is collected by filtration, washing with solvents, and drying. The relithiated electrode material is then ground with a lithium precursor and thermally treated at a relatively low temperature for a predetermined time period to obtain regenerated cathode material.

Belharouak, Ilias↗
DOE OSTI2025

Microwave-Assisted Activation of Mo/HZSM5 in Methane Dehydroaromatization

Natural gas flaring is a significant challenge for oil and gas producers. One viable option to mitigate flaring is the conversion of natural gas into valuable chemicals. Applying microwave energy to heterogenous catalyst materials offers advantages in terms of higher rates and product selectivities in comparison to traditional thermal systems which can be designed for on-demand chemical production in modular reactor systems. Methane dehydroaromatization (MDHA) produces transportable, liquid aromatic products directly from natural gas, which is ideal for remote production but is hindered by low thermodynamic yields and rapid deactivation. The stability and performance of the Mo/ZSM5 catalyst is often determined by the state and nature of Mo in the catalyst, which in turn is dictated by the temperature and gaseous environment during catalyst activation. In this study, the Mo/HZSM5 catalyst was activated under three different heating modes (thermal, microwave E-field, and microwave H-field) and four different gas environments (CO, He, CH4+H2, and H2). All the activated catalysts were characterized using different tools and performance evaluated in MDHA.

methane dehydroaromatization↗
DOE OSTI2024

Microwave-Assisted Gasification of Biochar: Effect of Operational Parameters and Biochar Composition on Syngas Production

The utilization of microwave-assisted gasification for biomass/plastic is a promising route toward clean energy production, contributing to a reduction in carbon footprint. This method facilitates the conversion of biomass into syngas with enhanced hydrogen (H2) yield, surpassing conventional heating approaches. However, the gasification of biochar, a byproduct resulting from the initial rapid pyrolysis of biomass, appears as a rate-determining step in biomass gasification. To ensure high conversion efficiency, particularly in pilot or larger scales, the maintenance of high biochar reactivity is essential, which can be achieved by introducing catalysts to minimize biochar formation. Furthermore, given the susceptibility of biochar to microwave heating, gaining a comprehensive understanding of its behavior in the presence of microwave-active catalysts under microwave conditions is crucial to obtain valuable insights into the underlying mechanisms, thereby improving overall biomass gasification efficiency. In the previous study, magnetite (Fe3O4) was selected for microwave-assisted gasification for biomass/plastic due to its dual role as a catalyst and microwave absorber and demonstrated considerably enhanced hydrogen production. Herein, Fe3O4 is rationally modified with metal promoters and their synergistic effect toward biochar gasification performance is investigated. The data shows that metal promoted Fe3O4 shows a higher syngas yield than that of pristine Fe3O4 in biochar.

Mai, Duy Hien↗
DOE OSTI2025

Microwave-assisted pyrolysis of liquid hydrocarbons using iron-based alumina catalysts obtained by solution combustion synthesis: The effect of synthesis parameters

The microwave-absorbing and catalytic properties of iron-based alumina (FeAl x O y ) materials have enabled their use as catalysts for the microwave-assisted generation of hydrogen and carbon via pyrolysis of hydrocarbons. Solution combustion synthesis (SCS) is a promising method to fabricate these materials, but the pyrolysis performance still needs to be improved. The present work investigated how altering the SCS parameters affects the pyrolysis of diesel fuel, gasoline, and crude oil. Two fuels (citric acid and glycine), four Fe:Al molar ratios, and two heating modes (hotplate and furnace) were tested. Fe/γ-Al 2 O 3 and Fe/β-SiC catalysts were prepared via incipient wetness impregnation for comparison. Among the three fossil fuels tested, diesel fuel yielded the highest amounts of H 2 and least amounts of CO x . The choice of fuel for the SCS process and the Fe/Al ratio strongly affected pyrolysis performance as they influence properties important for both catalysis and microwave absorption. The use of glycine resulted in catalysts that exhibited high H 2 yield and low CO 2 generation, which is explained by the revealed structural differences. The increase in the Fe:Al molar ratio accelerated microwave heating by adding more magnetic loss but also increased the amount of CO x . When the optimal SCS parameters were used, FeAl x O y catalysts outperformed Fe/γ-Al 2 O 3 and Fe/β-SiC. The high H 2 generation efficiency of the SCS catalysts is explained by their enhanced microwave-absorption properties. Scanning electron microscopy and energy dispersive X-ray spectroscopy revealed the formation of large-diameter CNTs via the tip-growth mechanism. The regeneration of SCS catalysts was demonstrated via the Boudouard reaction.

Carbon nanotubes↗
DOE OSTI2026

Effect of Mo precursors in Microwave-assisted Methane Dehydroaromatization over Mo/HZSM5 catalysts

Natural gas flaring occurs in remote shale regions due to limited pipeline takeaway capacity. The conversion of the associated natural gas into aromatics in modular microwave reactors is a viable alternative to monetize the wasted gas. Microwaves offer rapid, selective heating in compact reactor systems that can enable on-demand chemical production at the well-site. Mo-HZSM-5 catalysts are widely used for aromatic production, but the location and nature of the active sites are still under debate. This study focuses on the use of 6 different Mo precursors to elucidate insights into the Mo properties that are desirable for BTX production. The catalysts were characterized by different methods (XPS, TPR, Raman, etc) to determine differences in Mo catalytic properties that may affect performance and understand these differences through performance testing under microwave at 700C for methane dehydroaromatization. Metal precursors that enable a better distribution of Mo into the pores and over the surface lead to improved benzene yield, whereas those that limited Mo to primarily the surface suffer rapid deactivation and low benzene yields. Additionally, strong Lewis acidity that arises from the sodium containing precursor drastically shifts the product selectivity towards dehydrogenation, which produces more ethylene and carbon. This catalyst had the highest deactivation constant of all catalysts tested.

gas flaring reduction↗
DOE OSTI2024

Influence of Annealing Temperature on the OER Activity of NiO(111) Nanosheets Prepared via Microwave and Solvothermal Synthesis Approaches

Earth-abundant transition metal oxides are promising alternatives to precious metal oxides as electrocatalysts for the oxygen evolution reaction (OER) and are intensively investigated for alkaline water electrolysis. OER electrocatalysis, like most other catalytic reactions, is surface-initiated, and the catalyst performance is fundamentally determined by the surface properties. Most transition metal oxide catalysts show OER activities that depend on the predominantly exposed crystal facets/surface structure. Therefore, the design of synthetic strategies to obtain the most active crystal facets is of significant research interest. In this work, rock salt NiO OER catalysts with (111) predominantly exposed facets were synthesized by a solvothermal (ST) method either heated under supercritical or microwave-assisted (MW) conditions. Particular emphasis was placed on the influence of the post annealing temperature on the structural configuration and OER activity to compare their catalytic performances. The as-prepared electrocatalysts are pure α-Ni hydroxides which were converted to rock salt NiO (111) nanosheets with hexagonal pores after heat treatment at different temperatures. The OER activity of the electrodes has been evaluated in 0.1 M KOH using geometric and intrinsic current densities via normalization by the disk area and BET area, respectively. The lowest overpotential at a geometric current density of 10 mA/cm 2 is found for samples pretreated by heating between 400 and 500 °C with a catalyst loading of 115 μg/cm 2 . Despite the very similar nature of the catalysts obtained from the two methods, the ST electrodes show a higher geometric and intrinsic current density for 500 °C pretreatment. The MW electrodes, however, achieve an optimal geometric current density for 400 °C pretreatment, while their intrinsic current density requires pretreatment over 600 °C. Interestingly, pretreated electrodes show consistently higher OER activity as compared to the poorly crystalline/less ordered hydroxide as-prepared electrocatalysts. Thus, our study highlights the importance of the synthesis method and pretreatment at an optimal temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Multiscale modeling of packed-bed microwave reactors and estimation of intrinsic materials' permittivity

Modeling of packed-bed microwave reactors relies on an accurate representation of particle size, shape, and distribution within the bed, as well as the particles' dielectric properties. The measured permittivity of microwave susceptors (powders or structured materials) depends on the geometric features of the particles and the porosity of the bed, as well as the specific form factor of a structured material. These are effective properties and cannot be used to analyze other reactor configurations unless the geometric effects are removed. Therefore, we introduce a methodology for extracting the intrinsic particle permittivity from experimentally measured effective permittivity by combining cavity-based measurements with multiscale simulations and machine learning. Further, we develop the first multiscale model of packed-bed microwave reactors that incorporate particle effects (geometric features, random packing, and particle contact). This approach bridges macroscopic observables with mesoscopic physics, enabling analysis of local hotspots, arcing, and contact effects that control reactor performance. Using polymer-based spherical activated carbon (PBSAC) and silicon carbide (SiC) as examples, we demonstrate that the inferred particle permittivity is consistent with independent experimental heating profiles we collect from microwave reactors without adjustable parameters. Finally, this methodology establishes a foundation for predictive, multiscale design of microwave packed-bed reactors that explicitly accounts for particle-scale effects, enabling the estimation of intrinsic permittivity for the first time.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2025

Decarbonizing Solvent Chemistry Through Microwave Processing [Abstract]

National Energy Technology Laboratory and Covestro LLC. will collaborate on a project titled, “Decarbonizing Solvent Chemistry Through Microwave Processing”, which was selected for funding by DOE’s Office of Energy Efficiency and Renewable Energy (EERE) Industrial Efficiency and Decarbonization Office (IEDO) FOA DE-EE0002997. The project aims to develop a microwave-based approach for low-heat aqueous-based industry-relevant reactions currently conducted using a conventional fossil-energy fueled hydrothermal reactor. The team has combined expertise in the areas of polymer production, microwave assisted reactions and scale-up, and life cycle analysis to perform the tasks proposed.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2024

Abstract for CRADA between NETL and West Virginia University Research Corporation

The National Energy Technology Lab (NETL) will collaborate with West Virginia University to develop and demonstrate a dynamically operated modular, microwave-enhanced catalytic process for the co-production of ammonia and olefins. Ammonia and olefins (e.g., ethylene) are the most widely produced chemicals in the U.S. by volume, but their processes are also the most carbon and energy intensive as they rely on fossil-based feedstocks and combustion of fossil fuels for heating. The project will leverage the unique ability of microwaves to intensify process heating by providing pulsed, targeted energy to active sites of a mixed catalyst bed to convert a mixture of CH 4 /N 2 into ethylene and ammonia. The collaboration will facilitate the development of microwave technology that has the potential to utilize distributed waste resources like shale gas or biogas as well as renewable electricity to produce these valuable chemicals. It is expected that the results will decarbonize chemical production by using renewable energy and waste feedstocks, improve efficiency by reducing unit operations (H 2 production), and de-risk microwave technology for chemical production by demonstrating long-term and dynamic operability. This project was funded by an award from the Department of Energy’s EERE IEDO.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

The Effect of Metal Promoters in an Mo-Supported HZSM-5 Catalyst for Microwave-Assisted Methane Dehydroaromatization to Aromatics

Microwave (MW)-assisted methane dehydroaromatization (MDHA) using an Mo-supported HZSM-5 catalyst (Mo/HZ5) can convert methane into value-added aromatic products in modular microwave reactor systems, enabling producers to generate revenue from an otherwise wasted resource. Modifying the local environments of active Mo species with metal promoters potentially regulates the reaction/deactivation pathways and improves the heating properties of the Mo/HZ5 under microwaves. Herein, metal promoters (M), including monovalent K+ and bivalent Co2+ and Ni2+, were incorporated to form M-Mo/HZ5 and their MDHA performance was investigated.

metal promoters↗
DOE OSTI2026

Corroborating VNA and thermal measurements of transmission loss on the DIII-D ECH waveguide system

Electron cyclotron heating (ECH) and current drive (ECCD) will play a large role in tokamak-based fusion reactors. At the DIII-D tokamak, 110 GHz microwaves injected into the plasma can provide core heating and current drive as well as impurity control, neoclassical tearing mode mitigation, and breakdown assistance. Understanding the physics of these processes relies on accurate estimates of injected ECH power. DIII-D’s ECH system consists of six MW-class Microwave Power Products (MPP) gyrotron microwave sources. Operating the gyrotrons far from the tokamak removes them from magnetic field interference, so 31.75 mm inner-diameter corrugated waveguides transmit the microwave power the 80 m from the gyrotrons to steerable launchers in the tokamak chamber. Estimates of injected power rely on knowing the generated power at the source and then subtracting transmission loss. Conventional transmission loss measurements based on calorimetric dummy loads are onerous and only possible during extended maintenance periods. This work examines two tools that provide more flexibility for the transmission loss measurements. Furthermore, a resistive temperature detector (RTD) array installed along a waveguide measures heat lost to the transmission line, and low power time domain reflectometry (TDR) measurements with a vector network analyzer (VNA) allows loss measurements without burdensome hardware modifications.

ECH↗
DOE OSTI2025

Total Recycling of Copper Cable Scrap and Production of Carbon Using Fast Microwave Technology

The recycling of cable scrap, particularly from discarded electrical wiring, is gaining significant attention due to the rising demand for copper and the need for sustainable management of electronic waste. Traditionally, mechanical and thermal processings have been used to recover copper and plastic from cables. However, these approaches are often energy-intensive, time-consuming, and costly in terms of equipment and labor. In this study, we present a simple and effective method for recovering materials from cable scrap using a domestic microwave oven. Cable pieces (2–2.5 cm long) were exposed to 700 W of microwave irradiation under rotation for 30 s, enabling the rapid and efficient separation of high-quality copper metal from the core wire, and activated carbon from the carbonized plastic sheath. Microwaves facilitate this process through Ohmic heating, which induces electrical resistance in the metal, generating heat that mechanically loosens the metal and carbonized plastic components. The process demonstrates high efficiency, achieving an 80% reduction in energy consumption compared to conventional processings. This fast and energy-efficient method shows strong potential for scaling up to industrial recycling, offering a cost-effective and environmentally friendly way to recover high-quality materials for further use or repurposing.

Bourlinos, Athanasios B. (ORCID:0000000256165993)↗