Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “linear velocity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1956

Ram-jet Performance

The ram jet is basically one of the most dimple types of aircraft engine. It consists only of an inlet diffuser, a combustion system, and an exit nozzle. A typical ram-jet configuration is shown in figure 128. The engine operates on the Brayton cycle, and ideal cycle efficiency depends only on the ratio of engine to ambient pressure. The increased, engine pressures are obtained by ram action alone, and for this reason the ram jet has zero thrust at zero speed. Therefore, ram-jet-powered aircraft must be boosted to flight speeds close to a Mach number of 1.0 before appreciable thrust is generated by the engine. Since pressure increases are obtained by ram action alone, combustor-inlet pressures and temperatures are controlled by the flight speed, the ambient atmospheric condition, and by the efficiency of the inlet diffuser. These pressures and temperatures, as functions of flight speed and altitude, are shown in figure 129 for the NACA standard atmosphere and for practical values of diffuser efficiency. It can be seen that very wide ranges of combustor-inlet temperatures and pressures may be encountered over the ranges of flight velocity and altitude at which ram jets may be operated. Combustor-inlet temperatures from 500 degrees to 1500 degrees R and inlet pressures from 5 to 100 pounds per square inch absolute represent the approximate ranges of interest in current combustor development work. Since the ram jet has no moving parts in the combustor outlet, higher exhaust-gas temperatures than those used in current turbojets are permissible. Therefore, fuel-air ratios equivalent to maximum rates of air specific impulse or heat release can be used, and, for hydrocarbon fuels, this weight ratio is about 0.070. Lower fuel-air ratios down to about 0.015 may also be required to permit efficient cruise operation. This fuel-air-ratio range of 0.015 to 0.070 used in ram jets can be compared with the fuel-air ratios up to 0.025 encountered in current turbojets. Ram-jet combustor-inlet velocities range from 150 to 400 feet per second. These high linear velocities combined with the relatively low pressure ratios obtainable in ram jets require that the pressure drop through the combustor be kept low to avoid excessive losses in cycle efficiency. It has been estimated that, for a long-range ram-jet engine, an increase in pressure loss of one dynamic head would require a compensating 1-percent increase in combustion efficiency. Therefore, combustor pressure-loss coefficients (pressure drop/impact pressure) of the order of 1 to 4 are found in most current engines. The operating conditions described impose major problems in the design of stable and efficient ram-jet combustion systems. This chapter presents a survey of ram-jet combustor research and, where possible, points out criteria that may be useful in the design of ram-jet combustion systems.

Cervenko, A. J.↗
NASA NTRS2000

Spatiotemporal processing of linear acceleration: primary afferent and central vestibular neuron responses

Spatiotemporal convergence and two-dimensional (2-D) neural tuning have been proposed as a major neural mechanism in the signal processing of linear acceleration. To examine this hypothesis, we studied the firing properties of primary otolith afferents and central otolith neurons that respond exclusively to horizontal linear accelerations of the head (0.16-10 Hz) in alert rhesus monkeys. Unlike primary afferents, the majority of central otolith neurons exhibited 2-D spatial tuning to linear acceleration. As a result, central otolith dynamics vary as a function of movement direction. During movement along the maximum sensitivity direction, the dynamics of all central otolith neurons differed significantly from those observed for the primary afferent population. Specifically at low frequencies (</=0.5 Hz), the firing rate of the majority of central otolith neurons peaked in phase with linear velocity, in contrast to primary afferents that peaked in phase with linear acceleration. At least three different groups of central response dynamics were described according to the properties observed for motion along the maximum sensitivity direction. "High-pass" neurons exhibited increasing gains and phase values as a function of frequency. "Flat" neurons were characterized by relatively flat gains and constant phase lags (approximately 20-55 degrees ). A few neurons ("low-pass") were characterized by decreasing gain and phase as a function of frequency. The response dynamics of central otolith neurons suggest that the approximately 90 degrees phase lags observed at low frequencies are not the result of a neural integration but rather the effect of nonminimum phase behavior, which could arise at least partly through spatiotemporal convergence. Neither afferent nor central otolith neurons discriminated between gravitational and inertial components of linear acceleration. Thus response sensitivity was indistinguishable during 0.5-Hz pitch oscillations and fore-aft movements. The fact that otolith-only central neurons with "high-pass" filter properties exhibit semicircular canal-like dynamics during head tilts might have important consequences for the conclusions of previous studies of sensory convergence and sensorimotor transformations in central vestibular neurons.

NASA Discipline Neuroscience↗
NASA NTRS1982

Hydrogen two photon emission in the UV spectrum of type 2 supernovae

The continuum emission of Type 2 supernovae demonstrates an ultraviolet (UV) excess when fit by black body emission is attempted. The H two photon emission is advanced as an explanation of the UV excess. A function by which the UV spectra of two Type 2 supernovae (SN 1979c in NGC 4321 and SN 1980k in NGC 6946) are fitted with U,B,V photometric data is presented. The angular velocity of expansion of the supernovae envelope is derived. From this, the linear velocity of expansion and the distances of the parent galaxies are derived. A distance of 17.3 Mpc is obtained for NGC 4321, and a distance of 7.1 Mpc for NGC 6946.

Benvenuti, P.↗
NASA NTRS1998

Three-dimensional organization of otolith-ocular reflexes in rhesus monkeys. III. Responses To translation

The three-dimensional (3-D) properties of the translational vestibulo-ocular reflexes (translational VORs) during lateral and fore-aft oscillations in complete darkness were studied in rhesus monkeys at frequencies between 0.16 and 25 Hz. In addition, constant velocity off-vertical axis rotations extended the frequency range to 0.02 Hz. During lateral motion, horizontal responses were in phase with linear velocity in the frequency range of 2-10 Hz. At both lower and higher frequencies, phase lags were introduced. Torsional response phase changed more than 180 degrees in the tested frequency range such that torsional eye movements, which could be regarded as compensatory to "an apparent roll tilt" at the lowest frequencies, became anticompensatory at all frequencies above approximately 1 Hz. These results suggest two functionally different frequency bandwidths for the translational VORs. In the low-frequency spectrum (<<0.5 Hz), horizontal responses compensatory to translation are small and high-pass-filtered whereas torsional response sensitivity is relatively frequency independent. At higher frequencies however, both horizontal and torsional response sensitivity and phase exhibit a similar frequency dependence, suggesting a common role during head translation. During up-down motion, vertical responses were in phase with translational velocity at 3-5 Hz but phase leads progressively increased for lower frequencies (>90 degrees at frequencies <0.2 Hz). No consistent dependence on static head orientation was observed for the vertical response components during up-down motion and the horizontal and torsional response components during lateral translation. The frequency response characteristics of the translational VORs were fitted by "periphery/brain stem" functions that related the linear acceleration input, transduced by primary otolith afferents, to the velocity signals providing the input to the velocity-to-position neural integrator and the oculomotor plant. The lowest-order, best-fit periphery/brain stem model that approximated the frequency dependence of the data consisted of a second order transfer function with two alternating poles (at 0.4 and 7.2 Hz) and zeros (at 0.035 and 3.4 Hz). In addition to clearly differentiator dynamics at low frequencies (less than approximately 0.5 Hz), there was no frequency bandwidth where the periphery/brain stem function could be approximated by an integrator, as previously suggested. In this scheme, the oculomotor plant dynamics are assumed to perform the necessary high-frequency integration as required by the reflex. The detailed frequency dependence of the data could only be precisely described by higher order functions with nonminimum phase characteristics that preclude simple filtering of afferent inputs and might be suggestive of distributed spatiotemporal processing of otolith signals in the translational VORs.

Non-NASA Center↗
NASA NTRS1951

Effect of aspect ratio on the air forces and moments of harmonically oscillating thin rectangular wings in supersonic potential flow

This report treats the effect of aspect ratio on the air forces and moments of an oscillating flat rectangular wing in supersonic potential flow. The linearized velocity potential for the wing undergoing sinusoidal torsional oscillations simultaneously with sinusoidal vertical translations is derived in the form of a power series in terms of a frequency parameter. The series development is such that the differential equation for the velocity potential is satisfied to the required power of the frequency parameter considered and the linear boundary conditions are satisfied exactly. The method of solution can be utilized for other plan forms, that is, plan forms for which certain steady-state solutions are known.

Watkins, Charles E↗
NASA NTRS1980

Responses of the frog primary vestibular afferents to direct vibration of the semicircular canal

Responses of primary afferents (PA) of lateral semicircular canal to sinusoidal vibration of the canal wall within the range 0.05-200 Hz (mean amplitudes 5-15 microns) in immobilized frogs were studied. Dynamic characteristics (gain, phase) of relative linear velocity of the vibrator (micron X/s) were examined. At 0.2 Hz, the gain was 5.35 + or - 3.19 imp X/s /micron X/s (mean; S.D.; n=14) and linearly decreased if the frequency rose. Phase lag of relative velocity at 0.05 Hz was 49.8 deg + or - 16.5 deg (n=13) and at 1 Hz 97 deg + or - 9.4 deg (n=22). At 100 Hz phase lag was about 240 deg. Three groups of PA are described: wide range PA reacting in the range from 0.05 up to 60-180 Hz; high frequency PA responding in the range from 20-40 up to 100-150 Hz; and low frequency PA responding in the range from 0.05 up to 2-20 Hz.

Orlov, I. V.↗
NASA NTRS1984

Digital control system for space structural dampers

Digital control systems for space structural dampers, also referred to as inertia or proof-mass dampers are investigated. A damper concept is improved by adding a small taper to the proof-mass, and using a proximeter to determine position. Another damper using a three inch stroke rather than the standard one inch stroke is described. Provisions are made for a relative velocity feedback. In one approach, the digital controller is modified to accept the signal from a linear velocity transducer. In the other, the velocity feedback is included in the digital program. An overall system concept for the use of the dampers is presented.

Haviland, J. K.↗
NASA NTRS1947

Exploratory Investigation of Laminar-boundary-layer Oscillations on a Rotating Disk

Sinusoidal waves excited by random disturbances have been observed in the laminar boundary layer of a rotating disk at Reynolds numbers in a narrow range below the Reynolds number of transition. Their frequency was found to be approximately a constant times the velocity of the disk. The velocity of the waves at the radius of 11 inches was determined and found to be 0.2 linear velocity of the disk in a downstream direction, making an angle of approximately 14 degrees with the outward drawn radius vector.

Smith, Newell H↗
NASA NTRS1978

Visually induced motion in flight simulation

Visually induced yaw (circularvection) resulting from a moving wide field presentation, and its interaction with vestibular yaw cues generated by base motion is discussed. A model is presented for the interaction between visual and motion cues in yaw which rationalizes the high frequency utilization of vestibular cues and the low frequency use of visual cues to support sustained angular velocity. The implications for fixed and moving base flight simulator design are discussed. Similar considerations apply to visually induced linear velocity (linearvection) and interesting asymmetries in the fore-aft direction are noted. Visually induced pitch and roll are discussed and modelled in terms of conflict between the visually induced motion and the information regarding attitude based upon graviceptor signals.

Young, L. R.↗
NASA NTRS1983

Reduction of flow-measurement uncertainties in laser velocimeters with nonorthogonal channels

An analysis of certain geometrical limitations inherent in the application of laser velocimeters with nonorthogonal channels has led to the development of advanced-LDA-calibration and data-acquisition techniques that minimize systematic and statistical errors, respectively. The data-acquisition technique optimizes the number of velocity samples collected from three velocimeter channels as a function of local turbulence intensity, vector direction, and prescribed confidence interval. Linear velocity surveys and streamline traces measured in a turbulent flow field with a three-dimensional laser velocimeter are presented and the validity and accuracy of the theoretical analysis are discussed.

Snyder, P. K.↗
NASA NTRS1971

Device measures conductivity and velocity of ionized gas streams

Coaxial arrangement of primary coil and two sensing secondary coils contained inside slender quartz tube inserted into ionized stream permits simultaneous determination of conductivity and linear velocity. System results agree favorably with theory.

Cook, G. R.↗
NASA NTRSDate not supplied

Velocity Measurements in the Wake of the Swept Wing Flow Test Model at the National Transonic Facility

Femtosecond laser electronic excitation tagging (FLEET) was applied to obtain flowfield velocity data for the Swept Wing Flow Test (SWiFT) at the NASA Langley Research Center National Transonic Facility (NTF). Despite numerous challenges associated with performing flow velocimetry measurements within a large-scale cryogenic wind tunnel facility, the experimental campaign was conducted under various conditions, including dry air at 320 K, cool nitrogen at 240 K, and Mach numbers of 0.2 and 0.8. FLEET velocimetry measurements were performed in the downstream wake of the SWiFT model, providing a quantitative dataset. This dataset includes one-dimensional velocity profiles and two-dimensional velocity maps acquired at different angles of attack and Reynolds numbers. The two-dimensional single component velocity maps indicate relatively uniform flow across the 120-mm wide wake flow survey suggesting that the main flow features can be represented by single-position linear velocity profiles. The measured instantaneous velocity profiles at variable angles of attack are compared to model lift coefficient information obtained at Mach 0.2. At high Reynolds numbers, a sudden velocity decrease was observed in the FLEET measurements at the same time as stall in lift coefficient was observed. At a low Reynolds number, both the velocity profiles and the lift coefficient show a smoother transition, without a sudden stall. Furthermore, the two-dimensional, one component velocity map reveals a velocity deficit region at Mach 0.8 at various angles of attack. Both single shot and mean velocity measurements were acquired allowing assessment of flowfield fluctuations and measurement precisions. The uncertainties are within 4 m/s in mean measurements based on repeatability data and about 5 m/s in instantaneous single-shot measurements. Measurements are reported with ~4.8 mm spatial resolution with 32-pixel averaging used to reduce measurement errors.

femtosecond↗
NASA NTRSDate not supplied

Velocity Measurements in the Wake of the Swept Wing Flow Test (SWIFT) Model at the National Transonic Facility

Femtosecond laser electronic excitation tagging (FLEET) was applied to obtain flowfield velocity data for the Swept Wing Flow Test (SWiFT) at the NASA Langley Research Center National Transonic Facility (NTF). Despite numerous challenges associated with performing flow velocimetry measurements within a large-scale cryogenic wind tunnel facility, the experimental campaign was conducted under various conditions, including dry air at 320 K, cool nitrogen at 240 K, and Mach numbers of 0.2 and 0.8. FLEET velocimetry measurements were performed in the downstream wake of the SWiFT model, providing a quantitative dataset. This dataset includes one-dimensional velocity profiles and two-dimensional velocity maps acquired at different angles of attack and Reynolds numbers. The two-dimensional single component velocity maps indicate relatively uniform flow across the 120-mm wide wake flow survey suggesting that the main flow features can be represented by single-position linear velocity profiles. The measured instantaneous velocity profiles at variable angles of attack are compared to model lift coefficient information obtained at Mach 0.2. At high Reynolds numbers, a sudden velocity decrease was observed in the FLEET measurements at the same time as stall in lift coefficient was observed. At a low Reynolds number, both the velocity profiles and the lift coefficient show a smoother transition, without a sudden stall. Furthermore, the two-dimensional, one component velocity map reveals a velocity deficit region at Mach 0.8 at various angles of attack. Both single shot and mean velocity measurements were acquired allowing assessment of flowfield fluctuations and measurement precisions. The uncertainties are within 4 m/s in mean measurements based on repeatability data and about 5 m/s in instantaneous single-shot measurements. Measurements are reported with ~4.8 mm spatial resolution with 32-pixel averaging used to reduce measurement errors.

Transonic↗
DOE OSTI2024

Chiral kinematic theory and converse vortical effects

Response theories in condensed matter typically describe the response of an electron fluid to external electromagnetic fields, while perturbations on neutral particles are often designed to mimic such fields. Here, we study the response of fermions to a space-time-dependent velocity field, thereby sidestepping the issue of gauge charge. First, we use a semiclassical chiral kinematic theory to obtain the local density of current and extract the orbital magnetization. The theory immediately predicts a "converse vortical effect," defined as an orbital magnetization driven by linear velocity. It receives contributions from magnetic moments on the Fermi surface and the Berry curvature of the occupied bands. Then, transcending semiclassics via a complementary Kubo formalism reveals that the uniform limit of a clean system receives only the Berry curvature contribution while other limits sense the Fermi surface magnetic moments too. We propose CoSi as a candidate material and suggest magnetometry of a sample under a thermal gradient to detect the effect. Overall, our study sheds light on the effects of a space-time-dependent velocity field on electron fluids and paves the way for exploring quantum materials using new probes and perturbations.

Chen, Kai↗
NASA NTRS1952

An Impulse-Momentum Method for Calculating Landing-Gear Contact Conditions in Eccentric Landings

An impulse-momentum method for determining impact conditions for landing gears in eccentric landings is presented. The analysis is primarily concerned with the determination of contact velocities for impacts subsequent to initial touchdown in eccentric landings and with the determination of the effective mass acting on each landing gear. These parameters determine the energy-absorption requirements for the landing gear and, in conjunction with the particular characteristics of the landing gear, govern the magnitude of the ground loads. Changes in airplane angular and linear velocities and the magnitude of landing-gear vertical, drag, and side impulses resulting from a landing impact are determined by means of impulse-momentum relationships without the necessity for considering detailed force-time variations. The effective mass acting on each gear is also determined from the calculated landing-gear impulses. General equations applicable to any type of eccentric landing are written and solutions are obtained for the particular cases of an impact on one gear, a simultaneous impact on any two gears, and a symmetrical impact. In addition a solution is presented for a simplified two-degree-of-freedom system which allows rapid qualitative evaluation of the effects of certain principal parameters. The general analysis permits evaluation of the importance of such initial conditions at ground contact as vertical, horizontal, and side drift velocities, wing lift, roll and pitch angles, and rolling and pitching velocities, as well as the effects of such factors as landing gear location, airplane inertia, landing-gear length, energy-absorption efficiency, and wheel angular inertia on the severity of landing impacts. -A brief supplementary study which permits a limited evaluation of variable aerodynamic effects neglected in the analysis is presented in the appendix. Application of the analysis indicates that landing-gear impacts in eccentric landings can be appreciably more severe than impacts in symmetrical landings with the same sinking speed. The results also indicate the effects of landing-gear location, airplane inertia, initial wing lift, side drift velocity, attitude, and initial rolling velocity on the severity of both initial and subsequent landing-gear impacts. A comparison of the severity of impacts on auxiliary gears for tricycle and quadricycle configurations is also presented.

Yntema, Robert T↗
NASA NTRS1991

Factors influencing perceived angular velocity

Angular velocity perception is examined for rotations both in depth and in the image plane and the influence of several object properties on this motion parameter is explored. Two major object properties are considered, namely, texture density which determines the rate of edge transitions for rotations in depth, i.e., the number of texture elements that pass an object's boundary per unit of time, and object size which determines the tangential linear velocities and 2D image velocities of texture elements for a given angular velocity. Results of experiments show that edge-transition rate biased angular velocity estimates only when edges were highly salient. Element velocities had an impact on perceived angular velocity; this bias was associated with 2D image velocity rather than 3D tangential velocity. Despite these biases judgements were most strongly determined by the true angular velocity. Sensitivity to this higher order motion parameter appeared to be good for rotations both in depth (y-axis) and parallel to the line of sight (z-axis).

Kaiser, Mary K.↗
NASA NTRS1999

Yaw and pitch visual-vestibular interaction in weightlessness

Both yaw and pitch visual-vestibular interactions at two separate frequencies of chair rotation (0.2 and 0.8 Hz) in combination with a single velocity of optokinetic stimulus (36 degrees/s) were used to investigate the effects of sustained weightlessness on neural strategies adopted by astronaut subjects to cope with the stimulus rearrangement of spaceflight. Pitch and yaw oscillation in darkness at 0.2 and 0.8 Hz without optokinetic stimulation, and constant velocity linear optokinetic stimulation at 18, 36, and 54 degrees/s presented relative to the head with the subject stationary, were used as controls for the visual-vestibular interactions. The results following 8 days of space flight showed no significant changes in: (1) either the horizontal and vertical vestibulo-ocular reflex (VOR) gain, phase, or bias; (2) the yaw visual-vestibular response (VVR); or (3) the horizontal or vertical optokinetic (OKN) slow phase velocity (SPV). However, significant changes were observed: (1) when during pitch VVR at 0.2 Hz late inflight, the contribution of the optokinetic input to the combined oculomotor response was smaller than during the stationary OKN SPV measurements, followed by an increased contribution during the immediate postflight testing; and (2) when during pitch VVR at 0.8 Hz, the component of the combined oculomotor response due to the underlying vertical VOR was more efficiently suppressed early inflight and less suppressed immediately postflight compared with preflight observations. The larger OKN response during pitch VVR at 0.2 Hz and the better suppression of VOR during pitch VVR at 0.8 Hz postflight are presumably due to the increased role of vision early inflight and immediately after spaceflight, as previously observed in various studies. These results suggest that the subjects adopted a neural strategy to structure their spatial orientation in weightlessness by reweighting visual, otolith, and perhaps tactile/somatic signals.

NASA Center JSC↗