Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ion modification”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Retrofit and verification test of a 30-cm ion thruster

Twenty modifications were found to be necessary and were approved by design review. These design modifications were incorporated in the thruster documents (drawings and procedures) to define the J series thruster. Sixteen of the design revisions were implemented in a 900 series thruster by retrofit modification. A standardized set of test procedures was formulated, and the retrofit J series thruster design was verified by test. Some difficulty was observed with the modification to the ion optics assembly, but the overall effect of the design modification satisfies the design objectives. The thruster was tested over a wide range of operating parameters to demonstrate its capabilities.

Dulgeroff, C. R.↗
DOE OSTI2023

Comment on “Investigations on ion irradiation induced modifications in Th 5f occupancy in thoria,” by P. Jegadeesan, S. Amirthapandian, Gurpreet Kaur, D. Sanjay Kumar, Arindam Das, D.K. Avasthi, K. Ananthasivan, B.K. Panigrahi

The primary purpose of this letter is to address some issues raised in the paper by Jegadeesan et al. There are three salient points. (1) The Branching Ratio (BR) analysis of thorium dioxide is complicated by peaks from Extended X-Ray Absorption Fine Structure (EXAFS). (2) Uranium metal is not an LS coupling but rather a delocalized 5f case. (3) Radiation damage effects in the BR measurements are small but strong effects can be seen in Resonant Photoemission.

36 MATERIALS SCIENCE↗
NASA NTRS1987

Propagation of charge-neutral beams in space - Modifications when negative ions are present

Two-dimensional (three velocity component) electrostatic simulations are used to investigate the properties of a charge-neutral beam consisting of H(+), H(-), and electrons which will be used in the Beams on Rockets (BEAR) experiment to be launched in late 1987 or early 1988. For cross-field injection and beam densities much greater than the ambient plasma density, the beam splits into two approximately charge-neutral beams: a H(+)-e(-) beam that propagates down the field lines and a H(+)-H(-) beam that propagates at nearly the initial beam velocity on time scales less than the ion gyroperiod. Because of this splitting, space-charge oscillations are induced in the H(+)-H(-) component, which lead to its breakup. At lower beam densities, particularly when the beam electron density is less than about the density of the ambient plasma, the ambient plasma response reduces the space-charge fields as the beam splits and the space-charge oscillations are suppressed.

Winglee, R. M.↗
DOE OSTI2024

Global constraint on the jet transport coefficient from single-hadron, dihadron, and γ -hadron spectra in high-energy heavy-ion collisions

Modifications of large transverse momentum single-hadron, dihadron, and γ -hadron spectra in relativistic heavy-ion collisions are direct consequences of parton-medium interactions in the quark-gluon plasma (QGP). The interaction strength and underlying dynamics can be quantified by the jet transport coefficient q ̂ . We carry out the first global constraint on q ̂ using a next-to-leading order pQCD parton model with higher-twist parton energy loss and combining world experimental data on single-hadron, dihadron, and γ -hadron suppression at both RHIC and LHC energies with a wide range of centralities. The global Bayesian analysis using the information field (IF) priors provides the most stringent constraint on q ̂ ( T ) . We demonstrate in particular the progressive constraining power of the IF Bayesian analysis on the strong temperature dependence of q ̂ using data from different centralities and colliding energies. We also discuss the advantage of using both inclusive and correlation observables with different geometric biases. As a verification, the obtained q ̂ ( T ) is shown to describe data on single-hadron anisotropy at high transverse momentum well. Predictions for future jet quenching measurements in oxygen-oxygen collisions are also provided. Published by the American Physical Society 2024

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
NASA NTRS1990

Surface modification using low energy ground state ion beams

A method of effecting modifications at the surfaces of materials using low energy ion beams of known quantum state, purity, flux, and energy is presented. The ion beam is obtained by bombarding ion-generating molecules with electrons which are also at low energy. The electrons used to bombard the ion generating molecules are separated from the ions thus obtained and the ion beam is directed at the material surface to be modified. Depending on the type of ion generating molecules used, different ions can be obtained for different types of surface modifications such as oxidation and diamond film formation. One area of application is in the manufacture of semiconductor devices from semiconductor wafers.

Chutjian, Ara↗
DOE OSTI2020

Longitudinal dependence of B and D meson nuclear modifications in heavy-ion collisions at RHIC and the LHC

It is widely acknowledged that heavy flavor probes are sensitive to the properties of the quark-gluon plasma and are often considered an important tool for the plasma tomography studies. Forward rapidity observables can provide further insight on the dynamics of the medium due to the interplay between the medium size and the differences in the production spectra of heavy quark probes. In this proceedings we present the nuclear modification factor R AA 's for B and D mesons, as well as heavy flavor leptons, in the rapidity range -4.0 < y < 4.0 obtained from relativistic Langevin equation with gluon radiation coupled with a (3+1)-dimensional viscous hydrodynamics medium background. Finally, we present comparison with experimental data at mid-rapidity as well as predictions for different rapidity ranges.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2022

Electronic energy loss and ion velocity correlation effects in track production in swift-ion-irradiated LiNbO3: A quantitative assessment between structural damage morphology and energy deposition

The primary motivation for studying how irradiation modifies the structures and properties of solid materials involves the understanding of undesirable phenomena, including irradiation-induced degradation of components in nuclear reactors and space exploration, and beneficial applications, including material performance tailoring through ion beam modification and defect engineering. In this work, the formation mechanism of latent tracks with different damage morphologies in LiNbO 3 crystals under 0.09–6.17 MeV/u ion irradiation with an electronic energy loss from 2.6–13.2 keV/nm is analyzed by experimental characterizations and numerical calculations. Irradiation-induced damage is preliminarily evaluated via the prism coupling technique to analyze the correlation between the dark-mode spectra and energy loss profiles of irradiated regions. Under the irradiation conditions of different ion velocities and electronic energy losses, different damage morphologies, from individual spherical defects to discontinuous and continuous tracks, are experimentally characterized. During ion penetration process, the ion velocity determines the spatiotemporal distribution of deposited irradiation energy induced by electronic energy loss, meaning that the two essential factors including electronic energy loss and ion velocity co-affect the track damage. The inelastic thermal spike model is used to numerically calculate the spatiotemporal evolutions of energy deposition and the corresponding atomic temperature under different irradiation conditions, and a quantitative relationship is proposed by comparison with corresponding experimentally observed track damage morphologies. Additionally, the obtained quantitative relationship between irradiation conditions and track damage provides deep insight and guidance for understanding the damage behavior of crystal materials in extreme radiation environments and selecting irradiation parameters, including ion species and energies, for ion beam technique application in atomic-level defect manipulation, material modification, and micro/nanofabrication.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Nanostructures evolution assessment and spectroscopic properties modification induced by electronic energy loss in KTaO 3 crystal

Modifications of micro/nanostructure and photoelectric properties under swift ion irradiation (645 MeV Xe 35+ ) of KTaO 3 crystal with varying electronic energy losses (7.2–31.4 keV/nm) and ion velocities (0.18–5.00 MeV/u) have been studied by combining experimental and calculated approaches. The i-TS calculations combined with molecular dynamics simulations are compared with the experimental observations, revealing the inner track fine structures from individual spherical defects to continuous ion tracks with core–shell morphologies, and a quantitative relationship, including the melting (0.42 eV/atom), damage (0.75 eV/atom), and amorphous (1.71 eV/atom) thresholds, is established to successfully predict the inner disorder/amorphous proportions and track damage morphologies. The surface nanostructures of nanohillocks (isolated or partial overlaps) and nanopits (serious overlaps) directly depend on the combined action of the deposited potential and kinetic energies of incident ions, which induce local melting and sublimation in the near-surface region. Owing to the decreased recombination and the increased separation efficiency between electrons and holes, the higher photogenerated charge carrier mobility enhanced the photocurrent effect, further optimizing the photoconductivity performance in Xe 35+ -irradiated KTaO 3 . Therefore, controlled defect engineering using the ion irradiation technique, as an effective strategy, could design tailored nanostructure systems and regulate photoelectric properties, further promoting the development of novel technological applications.

36 MATERIALS SCIENCE↗
NASA NTRS1985

Simulations and observations of plasma depletion, ion composition, and airglow emissions in two auroral ionospheric depletion experiments

Observations of plasma depletion, ion composition modification, and airglow emissions in the Waterhole experiments are presented. The detailed ion chemistry and airglow emission processes related to the ionospheric hole formation in the experiment are examined, and observations are compared with computer simulation results. The latter indicate that the overall depletion rates in different parts of the depletion region are governed by different parameters.

Yau, A. W.↗
NASA NTRS1990

Observations of thermal ion influxes about the space shuttle

Ion mass spectrometer measurements made as part of the University of Iowa's Plasma Diagnostic Package on the STS-3 and Spacelab 2 Space Shuttle missions sampled a variety of ion composition and collected ion current responses to gas emissions from the vehicle. The only other shuttle ion measurements were made by an Air Force Geophysics Laboratory (AFGL) quadrupole spectrometer flown on STS-4. Gas emissions change the distribution of the incoming plasma through scattering and charge transfer processes. A background flux of contaminant ion species (mostly relating to water) always exists in the near vicinity of the shuttle with a magnitude which is dependent on the look direction of the spectrometer but which varies differently with changes in the angle of attack than that of the ambient ions. There is a near shuttle wake cavity in the contaminant ion distributions which has a different spatial configuration than the wake of the ambient ions. Although water dumps produce the most persistent ion perturbations, the sources for ion current modification were best delineated from measurements made when only one or two of the Reaction Control System thrusters fired for a relatively long duration. Contaminant ion perturbations associated with such firings were observed to persist for the order of a second after the cessation of the firings. The dense thruster plumes are efficient collisional, charge exchange barriers to the passage of ambient ions. Collected ion current perturbations were more evident for firings of the rear verniers, whose plumes scatter off projecting surfaces, than for the nose thrusters. The effect of the Vernier firings was found to depend not only on the location and attitude of the spectrometer with respect to the shuttle and thruster plume direction, but also on the orientation of the local magnetic field with respect to the shuttle velocity.

Grebowsky, Joe M.↗
NASA NTRS1986

Plasma assisted surface coating/modification processes: An emerging technology

A broad understanding of the numerous ion or plasma assisted surface coating/modification processes is sought. An awareness of the principles of these processes is needed before discussing in detail the ion nitriding technology. On the basis of surface modifications arising from ion or plasma energizing and interactions, it can be broadly classified as deposition of distinct overlay coatings (sputtering-dc, radio frequency, magnetron, reactive; ion plating-diode, triode) and surface property modification without forming a discrete coating (ion implantation, ion beam mixing, laser beam irradiation, ion nitriding, ion carburizing, plasma oxidation). These techniques offer a great flexibility and are capable in tailoring desirable chemical and structural surface properties independent of the bulk properties.

Spalvins, T.↗
NASA NTRS1987

Plasma assisted surface coating/modification processes - An emerging technology

A broad understanding of the numerous ion or plasma assisted surface coating/modification processes is sought. An awareness of the principles of these processes is needed before discussing in detail the ion nitriding technology. On the basis of surface modifications arising from ion or plasma energizing and interactions, it can be broadly classified as deposition of distinct overlay coatings (sputtering-dc, radio frequency, magnetron, reactive; ion plating-diode, triode) and surface property modification without forming a discrete coating (ion implantation, ion beam mixing, laser beam irradiation, ion nitriding, ion carburizing, plasma oxidation. These techniques offer a great flexibility and are capable in tailoring desirable chemical and structural surface properties independent of the bulk properties.

Spalvins, T.↗
DOE OSTI2019

The Poisson–Boltzmann model for implicit solvation of electrolyte solutions: Quantum chemical implementation and assessment via Sechenov coefficients

Here, we present the theory and implementation of a Poisson-Boltzmann implicit solvation model for electrolyte solutions. This model can be combined with arbitrary electronic structure methods that provide an accurate charge density of the solute. A hierarchy of approximations for this model includes a linear approximation for weak electrostatic potentials, finite size of the mobile electrolyte ions, and a Stern-layer correction. Recasting the Poisson-Boltzmann equations into Euler-Lagrange equations then significantly simplifies the derivation of the free energy of solvation for these approximate models. The parameters of the model are either fit directly to experimental observables-e.g., the finite ion size-or optimized for agreement with experimental results. Experimental data for this optimization are available in the form of Sechenov coefficients that describe the linear dependence of the salting-out effect of solutes with respect to the electrolyte concentration. In the final part, we rationalize the qualitative disagreement of the finite ion size modification to the Poisson-Boltzmann model with experimental observations by taking into account the electrolyte concentration dependence of the Stern layer. A route toward a revised model that captures the experimental observations while including the finite ion size effects is then outlined. This implementation paves the way for the study of electrochemical and electrocatalytic processes of molecules and cluster models with accurate electronic structure methods.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Local control of perpendicular magnetic anisotropy of Pd/Co multilayers via ion bombardment

In this work, we have controlled locally the magnetic anisotropy of PdCo multilayers using ion beam modification. First, we have used techniques with different probing depths to confirm that cobalt is partially oxidized in the Pd/Co multilayers exhibiting PMA fabricated by sputtering, presumably due to the diffusion of atmospheric oxygen migrated through the Pd capping layer. Then, low energy ion bombardment has been employed to induce a structural disorder in the upper layers of the multilayer, gradually reducing the PMA at local scale with increasing ion doses. Medium ion doses lead to a marked decline in PMA, resulting in equivalent magnetic anisotropy directions and the loss of characteristic labyrinthine magnetic domain morphology. High ion doses completely suppress PMA, yielding a typical in-plane shape anisotropy. Furthermore, by combining controlled PMA reduction via lithographic techniques, we create elongated structures displaying distinct magnetic responses; bombarded regions exhibit reduced PMA, whereas adjacent regions maintain their PMA. Notably, regions with reduced PMA do not disrupt the distribution of perpendicular magnetic domains in neighboring PMA regions, even at widths as narrow as 500 nm, demonstrating the robustness of the PMA domain structure.

Sebastiani-Tofano, Eugenia [Universidad Complutens↗