Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “impurities”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Measurement of near- and far-field impurity flows during pellet-induced rapid shutdown in DIII-D

Both near-field (<1 m away toroidally from the pellet) and far-field (>1 m away toroidally from the pellet) poloidal and toroidal impurity (carbon ion) flows are measured using visible imaging and fast bolometry during a polypropylene pellet-induced rapid plasma shutdown in the DIII-D tokamak. In the near field, the pellet appears to increase poloidal flow in the ion diamagnetic direction, possibly due to the strong radial temperature gradient caused by the pellet ablation. In the far field, the poloidal impurity flow typically appears slower and in the opposite direction. Toroidal impurity flow appears to be strongly influenced by the plasma initial toroidal rotation, especially in the far field. These results demonstrate that rapid shutdown impurity flows are not necessarily global in structure but can be quite different close to and far from the injected pellet.

Electromagnetic radiation detectors↗
DOE OSTI2025

Sticking Coefficients of Fusion Reactor Impurities from Molecular Dynamics Simulations for the Design of Cryopumps

A cryopump can be utilized as an impurity removal component of a direct internal recirculation (DIR) system for the fusion fuel cycle. The DIR facilitates a low fuel inventory by continuously pumping unburnt fuel while removing impurities from the fusion exhaust stream. A cryopump can target multiple impurity species by maintaining a temperature lower than the gas triple-point temperature that promotes desublimation. The desublimation/condensation of gases in cryopumps can be characterized by the sticking coefficient, which is defined as the probability for a gas particle to stick to a (cryo-)surface upon collision. The sticking coefficient is one of the important design/operation parameters for cryopumps, and it depends on a variety of surface and gas properties. Here, in this study, molecular dynamics simulations were utilized to estimate the sticking coefficients of typical fusion gas impurity species N 2 , CO 2 , and CH 4 over a Cu surface for a range of gas temperatures and surface coverages. The molecular dynamics study showed that the sticking coefficients for gases decrease with an increase in gas temperature. The presence of a single full monolayer of condensate on the metallic surface showed an adverse effect on the sticking of gases; however the sticking improved with two full monolayers of condensate on the surface. The sticking of gases over the mixed condensate on a surface was more favorable than the condensate of the same species for N 2 and CH 4 , with an exception for CO 2 , which showed a decrease in sticking over the mixed condensate.

cryopump↗
DOE OSTI2026

Quantum solver for single-impurity Anderson models with particle-hole symmetry

Quantum embedding methods, such as dynamical mean-field theory (DMFT), provide a powerful framework for investigating strongly correlated materials. A central computational bottleneck in DMFT is in solving the Anderson impurity model (AIM), whose exact solution is classically intractable for large bath sizes. In this work, we benchmark a quantum-classical hybrid solver tailored for particle-hole symmetric AIMs, using the variational quantum eigensolver to prepare the ground state of the model with shallow quantum circuits. The solver uses shallow quantum ansätze and one set of variational parameters to prepare the ground state and its particle and hole excitations, enabling the construction of the impurity Green’s function through a continued-fraction expansion. We evaluate the performance of this approach across a few bath sizes and interaction strengths under noisy, shot-limited conditions. We compare three optimization routines (COBYLA, Adam, and L-BFGS-B) in terms of convergence and fidelity, assess the benefits of estimating a quantum-computed moment correction to the variational energies, and benchmark the approach by comparing the density of states computed from the impurity Green’s function against that obtained using a classical pipeline. Our results demonstrate the feasibility of Green’s function construction on near-term devices and establish practical benchmarks for quantum impurity solvers embedded within self-consistent DMFT loops.

Karabin, Mariia [ORNL]↗
DOE OSTI2024

Impact of Silicon Impurity on the Hydrometallurgical Recovery of NCM622 Cathode

Hydrometallurgy is one of the best approaches to date for recycling LIBs due to its high efficiency, low energy usage, and industrial scalability. However, impurities have always been a thorny issue because they could have unintended impacts on the recovered cathode materials. This research marks the first systematic investigation into the influence of silicon impurity on the LiNi 0.6 Co 0.2 Mn 0.2 O 2 (NCM622) cathode obtained from hydrometallurgical recycling. Here we find that silicon nanoparticles will be nucleated at the center of the precursor particles during co-precipitation synthesis, and the silicon core will slowly dissolve in the surrounding ammonia, creating a special hollow structure in the particle. More importantly, the dissolution of silicon impurity will eventually lead to the deposition of silicates in the cathode material, which is an unfavorable result. Test data indicate that NCM622 cathode with 5 at% silicon has a capacity of 148.8 mAh g −1 after 100 cycles at 1/3 C, approximately 10 mAh g −1 lower than the virgin. Despite being relatively mild, the adverse influence of silicon impurity in hydrometallurgical recycling still requires attention.

25 ENERGY STORAGE↗
DOE OSTI2026

Analysis of vapor diffusion Nb$^{3}$Sn coating at Fermilab: Minimizing impurities using TOF-SIMS

Nb₃Sn demonstrates steady advancements nowadays offering reduced power cost in superconducting radio-frequency cavities due to its high critical temperature, quality factor, and achieved accelerating gradient. However, theoretical estimates of its radio-frequency parameters have not been achieved due to several potentially limiting mechanisms: tin spots, patchy regions, defects, thermal impedance, and impurities. While some of these limitations have been intensively studied, impurity analysis in Nb$_3$Sn coatings have received less attention. We report an investigation of impurities in several vapor-diffused Nb₃Sn coated samples using time-of-flight secondary ion mass spectroscopy (TOF-SIMS) and show allowable impurity levels in view of superconducting cavity performance. Challenges and lessons learned in maintaining clean Nb$_3$Sn coatings are also discussed.

Tagdulang, Nikki [Fermilab]↗
DOE OSTI2025

Challenges of Vapor Diffusion $Nb_3Sn$ Coating at Fermilab: Minimizing Impurities Using TOF-SIMS

Nb$_3$Sn demonstrates steady advancements nowadays offering reduced power cost in superconducting radio-frequency cavities due to its high critical temperature, quality factor, and achieved accelerating gradient. However, theoretical estimates of its radio-frequency parameters have not been achieved due to several potentially limiting mechanisms: tin spots, patchy regions, defects, thermal impedance, and impurities. While some of these limitations have been intensively studied, impurity analysis in Nb$_3$Sn coatings have received less attention. We report an investigation of impurities in several vapor-diffused Nb$_3$Snn coated samples using time-of-flight secondary ion mass spectroscopy (TOF-SIMS) and show allowable impurity levels in view of superconducting cavity performance. Challenges and lessons learned in maintaining clean Nb$_3$Sn coatings are also discussed.

Tagdulang, N. [Fermilab]↗
DOE OSTI2025

Surface Local Impurity Scattering as a Probe for Topological Kondo Insulators

Shortly after the discovery of topological band insulators, topological Kondo insulators (TKIs) is also theoretically predicted. The latter has ignited revival interest in the properties of Kondo insulators. Currently, the feasibility of topological nature in SmB 6 is intensively analyzed by several complementary probes. Here by starting with a minimal-orbital Anderson lattice model, the local electronic structure is explored in a Kondo insulator. It is showed that the two strong topological regimes sandwiching the weak topological regime give rise to a single Dirac cone, which is located near the center or corner of the surface Brillouin zone. It is further found that, when a single impurity is placed on the surface, low-energy resonance states are induced in the weak scattering limit for the strong TKI regimes and the resonance level moves monotonically across the hybridization gap with the strength of impurity scattering potential; while low energy states can only be induced in the unitary scattering limit for the weak TKI regime, where the resonance level moves universally toward the center of the hybridization gap. These impurity-induced low-energy quasiparticles will lead to characteristic signatures in scanning tunneling microscopy/spectroscopy, which has recently found success in probing into exotic properties in heavy fermion systems.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Impacts of Lanthanum Impurities on Nickel-Rich Cathode Materials

The widespread use of lithium-ion batteries (LIBs) has led to environmental concerns and exacerbated the scarcity of essential minerals, underscoring the urgent need for effective recycling strategies. Among various recycling methods, the hydrometallurgical process is distinguished by its energy efficiency and minimal environmental impact. Nickel-metal hydride (Ni-MH) batteries are a significant source of nickel sulfate (NiSO 4 ) for hydrometallurgical recycling due to their substantial nickel content. A significant challenge arises from the effective separation of lanthanum (La), which results in at least 20 ppm of La being present in the recycled NiSO 4 . This study explores a critical aspect of the recycling process: the impact of La 3+ impurities, introduced through recycled NiSO 4 , on the performance of the synthesized nickel-rich cathode materials. We conducted a thorough investigation into how La 3+ influences morphology and structural integrity during both the synthesis of precursors and the production of cathode materials. Our findings indicate that La 3+ impurities do not adversely affect the morphology or structural integrity of the cathode precursors relative to virgin materials. However, higher concentrations of La 3+ reduce the discharge capacity with enhanced cycle stability by minimizing cation mixing between lithium (Li + ) and nickel (Ni 2+ ) ions within the cathode. Furthermore, this stability is crucial for extending battery life. Therefore, controlling the concentration of La 3+ impurities is essential for optimizing the electrochemical performance of recycled cathode materials.

Corrosion↗
DOE OSTI2024

Glow Discharge Boronization and Real-Time Boronization Using an Impurity Powder Dropper in LHD

In the Large Helical Device (LHD), boronization is utilized for wall conditioning, employing two distinct methods: glow discharge using diborane gas and the injection of boron powder into the plasma via an impurity powder dropper (IPD). Glow discharge boronization is conducted after maintenance when the vacuum vessel is exposed to air and just before the start of an experimental campaign. In contrast, real-time boronization using the IPD is performed during discharges. The distribution of boron on plasma-facing components was assessed through long-term material probes in the case of glow discharge and through numerical simulations for the IPD method. Results indicated non-uniform boron distributions in both cases. The impact of these boronization techniques on impurity levels and the lifetime of their effects were also examined. Both methods effectively reduced oxygen and iron in the plasma, with the iron impurities originating from the first wall. For glow discharge boronization, the reduction in oxygen levels persisted until the end of the experimental campaign, whereas the reduction in iron levels only lasted a few days. In the case of boron injection during long pulse discharges exceeding 200 s, the suppression of oxygen and iron was observed. The effect on iron quickly diminished within several seconds after the injection ended, whereas the effect on oxygen lasted more than 100 s. The difference in the lifetimes of the boronization effects is further discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Fully generalized, turbulent trace impurity transport with Gkeyll and Flan in the DIII-D far-SOL

The Monte Carlo trace impurity turbulent transport code Flan is introduced for the first time. Flan follows impurities in a turbulent background plasma from Gkeyll using the Lorentz force to resolve the full particle gyro orbit. Collisions are handled using the Nanbu collision algorithm (Nanbu 1997 Phys. Rev. E 55 4642–52), and ionization/recombination is handled via ADAS coupling. The far-SOL of a generic DIII-D L-mode is simulated with and without the collision model to show how collisions affect radial tungsten transport. Anomalous diffusion coefficient (D r ) and pinch velocity (v p ) profiles are extracted from fits to the results. With collisions, D r and v p are between 0–1.0 m 2 s −1 and −100–100 m s −1 , respectively. Without collisions, D r and v p are between 0–0.3 m 2 s −1 and −50–50 m s −1 , respectively. Exponential fits to the radial W density profiles and experimental data from W deposition along a collector probe are in good agreement, demonstrating Flan as a useful interpretive modeling tool. Additional simulations show that impurity transport away from the wall increases with atomic number, though it is not clear why. Flan has the potential to better interpret existing data and improve reactor scale predictions of core contamination because the underlying physics model is very general and does not rely on arbitrary user-defined transport coefficients.

DIII-D↗
DOE OSTI2024

Gyrokinetic prediction of core tungsten peaking in a WEST plasma with nitrogen impurities

Tungsten peaking is predicted in the core of a WEST plasma with total-f gyrokinetic simulations, including both collisional and turbulent transport. This prediction is validated with a synthetic diagnostic of the bolometry. Although nitrogen impurities are shown to reduce the neoclassical peaking of tungsten on-axis, the overall tungsten peaking increases when nitrogen impurities are present, as they reduce the turbulence screening off-axis. This finding is important for the plasma current ramp-up phase of ITER, where light impurities seeding will be desirable to achieve low temperatures at the plasma-facing components and reduce tungsten sputtering. It provides further argument for applying early ECRH heating to maintain margins on the core power balance. The neoclassical peaking factor is cross-verified between XGC and FACIT. The heat flux at separatrix and the heat load width are modeled by XGC and compared to WEST data.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Chirality reversal at finite magnetic impurity strength and local signatures of a topological phase transition

Here, we study the honeycomb lattice with a single magnetic impurity modeled by adding imaginary next-nearest-neighbor hopping 𝑖⁢ℎ on a single hexagon. This Haldane defect gives a topological mass term to the gapless Dirac cones and generates chirality. For a small density of defects, Neehus et al. [Phys. Rev. Lett. 135, 126604 (2025)] found that the system's chirality reverses at a critical ℎ 𝑐 ≈ 0.95 associated with an unexpected tricritical point of Dirac fermions at zero defect density. We investigate this zero-density limit by analyzing a single defect and computing two experimentally relevant measures of chirality: (1) orbital magnetization via local Chern marker, a bulk probe of all occupied states; and (2) electronic currents of low-energy states. Both probes show a chirality reversal at a critical ℎ 𝑐 ≈ 0.9–1.0. Motivated by this consistency, we propose a defect-scale toy model whose low-energy states reverse their chirality at ℎ$^{'}_{c}$ ≈ 0.87. Remarkably, the same pair of zero-energy bound states also generates the critical point ℎ 𝑐 in the full impurity projected T-matrix. Our results show how the chirality reversal produced by an impurity can be observed either in local probes or in the global topology, and suggest a possible role of the microscopic defect structure at the critical point.

Chern insulators↗
DOE OSTI2025

A GPU ‐Accelerated 3D Unstructured Mesh Based Particle Tracking Code for Multi‐Species Impurity Transport Simulation in Fusion Tokamaks

ABSTRACT This paper presents the multi‐species global impurity transport capability developed in a GPU‐accelerated fully 3D unstructured mesh‐based code, GITRm, to simultaneously track multiple impurity species and handle interactions of these impurities with mixed‐material surfaces. Different computational approaches to model particle‐surface interaction or surface response have been developed and compared. Sheath electric field is taken into account by employing a fast distance‐to‐boundary calculation, which is carried out in parallel on distributed or partitioned meshes on multiple GPUs without the need for any inter‐process communication during the simulation. Several example cases, including two for the DIII‐D tokamak, that is, one with the SAS‐V divertor and the other with the collector probes, are used to demonstrate the utility of the current multi‐species capability. For the DIII‐D probe case, the capability of GITRm to resolve the spatial distribution of particles in localized regions, such as diagnostic probes, within non‐axisymmetric tokamak geometries is demonstrated. These simulations involve up to 320 million particles and utilize up to 48 GPUs.

Nath, Dhyanjyoti D. [Scientific Computation Resear↗
DOE OSTI2026

Effect of Oxidizing Impurities on the Corrosion Behavior of Structural Alloys Exposed to MgCl 2 Molten Salt Vapor

The corrosion behavior of structural alloys SS304 and IN617 when exposed to vapors of MgCl 2 molten salt at 764 °C for 100 h in an argon atmosphere was investigated as a function of the level of oxidizing impurities (e.g., NaOH) present in the salt. Increasing the concentration of oxidizing impurities in the salt caused an increase in corrosion in both structural alloys, as measured by Cr depletion layers. A poorly adhered oxide scale layer containing Mg, Al, and Cr was observed on the surface of the metals, and local attack was observed as well. The Ni-based IN617 showed lower Cr depletion and less scale formation than the Fe-based SS304. These results demonstrate that oxidizing impurities in the molten salt will impact the vapor phase corrosion for structural members exposed to the molten salt headspace. This finding is highly relevant for understanding the effects of the vapor phase in molten salt applications, including molten salt thermal energy storage, molten salt nuclear reactors, and molten salt electrochemistry.

25 ENERGY STORAGE↗
DOE OSTI2024

Effect of Si impurities on microstructure and tensile properties of a cast Al-Mg-Fe alloy

Al-Mg alloys are attractive for structural castings owing to their superior strength and ductility in the as-cast state. However, given the tight tolerance for impurities, Al-Mg alloys produced from secondary sources still face multiple challenges. Here, we report the effect of increased Si impurity (0.05–1.6 wt%), which is commonly found in secondary Al sources, on microstructure and tensile properties of a cast Al-4.3Mg-1.6Fe (wt%) alloy, commercially referred to as Castaduct-42 alloy. Microstructural characterization revealed that Si addition increased the volume fraction, size, and aspect ratio of primary Al13Fe4 intermetallic particles as well as the volume fraction of other binary and ternary eutectic phases. Tensile testing results demonstrated that increasing Si impurities from 0.05 to 1.6 wt% reduced ductility from 14.3 ± 1.4 % to 2.2 ± 1.0 %. A particle cracking damage accumulation model coupled with failure analysis indicated primary Al13Fe4 intermetallic particles to be the major contributing factor to the deterioration in ductility with increasing Si content. Additionally, the stabilizing effect of Si on primary Al 13 Fe 4 was inconsistent with the CALPHAD calculation results based on existing CALPHAD databases which predict a slightly decreasing primary Al13Fe4 phase fraction with increasing Si concentration. This work provides new insights into the phase stability and mechanical behavior of the lesser studied Al-Mg-Fe-Si alloy system that will contribute to the development of sustainable cast Al-Mg based alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Inversion of dislocation-impurity interactions in α -Fe under magnetic state changes

Here, in this work, we investigate the dislocation-impurity interaction energies and their profiles for various 3d elements —V, Cr, Mn, Cu, Ni, and Co —in and around 1/2 $\langle111\rangle$ screw dislocations in α -Fe using ab initio methods. We consider the ferromagnetic and paramagnetic states, with the latter being modeled through both the disordered local moment model and a spin-wave approach. Our findings reveal that (1) magnetic effects are large compared to size misfit effects of substitutional impurities, and (2) dislocation-impurity interactions are dependent on the magnetic state of the matrix and thermal lattice expansion. In particular, Cu changes from core-attractive in the ferromagnetic state to repulsive in the paramagnetic state.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Real-Time Detection of Hydrogen and Ammonia Isotopologues for Impurity Removal and Recovery of Tritium

To accommodate gas measurements for impurity removal and recovery of tritium, a silver-coated optical or waveguide is employed for collecting Raman scattered signals to determine relative hydrogen and ammonia isotopologue populations in real time. The data and results presented here demonstrate an analytical methodology for the analysis of four ammonia and three hydrogen isotopologues in a hydrogen–deuterium exchange reaction by gas phase Raman spectroscopy. Standard chemometric modeling techniques effectively unravel the signatures of the isotopologues involved observed here; however, a sophisticated quantum chemical approach supports the spectral assignments. An interpretation of the data presented here can emphasize the practicality and reliability of the gaseous monitoring system in complex chemical environments for the hydrogen fuel economy as well as the more distant energy source from a facility that handles tritium. There are still considerable concerns about the measurement of tritium in isotope separation and radiological impurities from gas processing. A common impurity in gas processing is ammonia, which can form readily in the presence of nitrogen and tritium. Substituted ammonia (NQ 3 ), where Q = H, D, or T, is traditionally removed through getters or diffusers along with other non-hydrogen contaminants. A preferable analytical approach is noninvasive and can be deployed for real-time process evaluation in radiological environments.

Ammonia↗
DOE OSTI2025

Text-mined dataset of solid-state syntheses with impurity phases using Large Language Model

Solid-state synthesis is widely used to obtain various inorganic materials, such as battery materials and bulk thermoelectrics. Despite its prevalence, the process remains challenging due to the lack of a general theory and well-understood underlying reaction mechanisms. While prior works have successfully extracted structured datasets from literature, they often neglect product phase purity or yield. In this work, we construct a solid-state synthesis dataset consisting of 80,806 syntheses extracted with a large language model (LLM), including 18,869 reactions with impurity phase(s). Our dataset not only validates expected thermodynamic trends for impurity phase formation but also identifies challenging cases where impurity phases emerge even when the target phase is significantly more stable.

Lee, Sanghoon↗