Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “delay errors.”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Genetic algorithm optimization of a chemical kinetic mechanism for propane at engine relevant conditions

Propane has demonstrated significant potential for reductions in greenhouse gas and pollutant emissions in medium- and heavy-duty engine applications, but further improvements require accurate, compact, and scalable chemical kinetic mechanisms to design the next generation of propane fueled engines, particularly at the boosted operating conditions necessary to meet the power density demand of medium- and heavy-duty applications. In this work, six key chemical reactions were identified in a reduced mechanism with 70 species and 352 reactions through a sensitivity analysis performed at conditions typical of thermodynamic trajectories observed in a high compression ratio, long stroke engine operated on propane from throttled to boosted operating conditions. While the original mechanism was validated against rapid compression machine (RCM) data, it was found to overpredict experimental autoignition tendencies in 2-zone, 0-D SI engine simulations performed in Chemkin Pro. Subsequently, a genetic algorithm approach was used to optimize the six reaction rate parameters within established uncertainty bounds by performing RCM simulations and comparing to two independent sets of literature ignition delay times for propane, thus generating two new kinetic mechanisms. The first optimization achieved a mean absolute percent error (MPE) reduction in 2nd stage ignition delay of 61.4% in seven generations, while the second optimization utilized a newer experimental RCM dataset, and achieved MPE reduction of 56.7% in seven generations, and further marginal improvement to 57.8% reduction in 34 generations. Finally, the two mechanisms were then evaluated again in the 2-zone 0-D SI engine model in Chemkin Pro comparing typical mean and knocking cycle trajectories, and it was found that the second optimized mechanism provided better prediction of knock onset at the representative conditions evaluated in this work, particularly for higher load operating conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Estimators and Fusers for Fiber Delay Estimation Using Environmental Measurements

The properties of deployed network fiber are affected by environmental factors due to their exposure to the elements. Particularly for quantum networks, the resultant delay variations may have significant impacts due to the extreme sensitivity of synchronization, coincidence counting, and other critical operations. In this paper, the delays of 15 km aerial-inground fiber connections are measured, and effects due to temperature, humidity and wind speed are analyzed over multiple periods spanning four seasons of a year. Machine learning methods are first utilized to reveal surprisingly pronounced effects of humidity on the delay, in addition to the expected temperature and its seasonal variations. Estimator and fusion methods are developed to estimate the delay using temperature, humidity and wind speed measurements, by utilizing smooth Gaussian Process Regression (GPR) and nonsmooth Ensemble of Trees (EOT) methods. Measurements from winter and summer periods are temporally fused using twelve different methods, and eight methods provide estimates for the delay throughout the year with median test errors under 1.28%. The results reveal distinct temperature-humidity trends across the seasons, and the ability of estimator and temporal fusion methods to exploit them for estimating the delay. These results constitute a case study of machine learning analytical results, wherein generalization equations explain the performance of various estimator and fuser methods.

Rao, Nageswara [ORNL] (ORCID:0000000234085941)↗
DOE OSTI2024

Simulation Evaluation of a Large-Scale Implementation of Virtual-Phase Link-Based Model Predictive Control

Traffic congestion is a serious problem in the US, and traffic signal control is one of the effective solutions to congestion. Previous research on model predictive control (MPC)-based traffic signal control showed substantial benefits over conventional methods. This study focused on implementing MPC over a large-scale network with complex intersections and the impact of cycle length, network size, and imperfect state estimation on performances. This study implemented a virtual phase link (VPL)-based model predictive control method which used the number of vehicles in each VPL as input state variables and was suitable for National Electrical Manufacturing Association (NEMA) ring-barrier control. To test the impact of network size, the performance of distributed MPC (36 intersections in the network are divided into five subnetworks) was compared with that of MPC over the full network for a set of cycle lengths. To test the impact of imperfect state estimation, we synthetically infused estimation error and developed two scenarios, MPC-error and MPC-error narrow, which had higher and lower estimation errors, respectively. The performance of these MPC methods was compared with that of the existing time-of-day (TOD) method and an offline method that used Webster's method for split and MULTIBAND for cycle length and offset optimization. Trajectory and linkwise signal performance measures were collected from the simulation to evaluate performance. The distributed MPC method with perfect state estimation had the lowest delay and highest energy efficiency of all the methods. The performance of MPC decreased as the prediction inaccuracy increased. MPC-error had 7% and 11% more delay than MPC-error narrow in the morning and evening peaks, respectively. Overall, simulation results suggest that even with imperfect state estimation, MPC methods will outperform offline methods significantly.

large-scale simulation↗
DOE OSTI2026

High-fidelity entanglement and coherent multi-qubit mapping in an atom array

Neutral atoms in optical tweezer arrays possess broad applicability for quantum technologies, such as computing, analogue simulation and metrology. The atomic species ytterbium-171 is able to host multiple types of qubits, making it a strong candidate for bridging various applications of tweezer arrays. Realizing this potential requires high-fidelity generation and transfer of many-body entanglement between these distinct qubit degrees of freedom. Here, in this study, we demonstrate the creation and coherent mapping of entangled quantum states across multiple qubits in ytterbium-171 tweezer arrays. We map entangled states onto the optical clock qubit from the nuclear spin qubit or the Rydberg qubit. We coherently transfer Z 2 -ordered Greenberger–Horne–Zeilinger states of up to 20 atoms from the interacting Rydberg manifold to the metastable nuclear spin manifold. Furthermore, we find that clock-qubit-based spin detection, when applied to Rydberg and nuclear spin qubits, facilitates atom-loss-detectable qubit measurements and Rydberg decay detection. This enables delayed-erasure detection, yielding an error-detected two-qubit gate fidelity of 99.78(4)% in metastable qubits. These results establish a versatile architecture that advances multiple fields of quantum information science while also establishing bridges between them.

Senoo, Aruku [University of Colorado, Boulder, CO ↗
DOE OSTI2022

Alternative analysis of the MINERVE ZPR oscillation experiments

Delayed neutrons are of fundamental importance in the field of nuclear reactor dynamics and control. However, the precursor yield fraction for a given nuclear reactor are dependent on the properties of the reactor. Thus, in-pile experiments, such as oscillation experiments are conducted in order to measure those values. In this work, an alternative analysis of the piston oscillation experiments that have been conducted in the MINERVE reactor in 2013 is performed. A new method which evolves effective terms that cancel out undesired drifts of the flux during the experiments is presented. The evaluation of the uncertainty on the values of the response function is also presented. Moreover, the effective delayed neutron fraction β{sub eff} is evaluated and is compared to results in previous works. As the analysis has led to an estimation of β{sub eff} with a large uncertainty, it has been deduced that the oscillation experiments that have been conducted in MINERVE are not a reliable method of experimentation to determine the value of β{sub eff} in the reactor and that the noise experiments are better suited for that purpose.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2023

Kinetic model-based group contribution method for derived cetane number prediction of oxygenated fuel components and blends

A four-step autoignition model was used to derive an expression for the ignition delay (ID) measured in ignition quality testers (IQT) with the derived cetane number (DCN) determined from this ID using the ASTM D6890 standard correlation. The model predicts DCN for individual compounds and blends as a function of each compound's global initiation and net chain branching rate constants. Expressions for these values were determined assuming they could be related to the functional groups present in each compound. Measurement data for 125 compounds and 94 binary and ternary blends (including oxygenates: alcohols, aldehydes, esters, ethers, and ketones), from literature and from measurements performed in our lab, were used to obtain the dependence of the measured ignition delay on each functional group. The new kinetic model-based group contribution method was able to predict the ignition delay of both pure compounds and blends, with an average DCN error of 4.4 (19%) and 2.8 (11%), respectively. Here, the blend model was also used to develop an ID mixing rule by incorporating existing IQT ignition delay data for each compound. Use of the mixing rule gave an average DCN error of 3.6 (16%) for blends. Both the blend model and mixing rule were found to be superior compared to standard linear by volume fraction or mole fraction mixing rules commonly used to estimate the DCN of mixtures.

42 ENGINEERING↗
DOE OSTI2023

The Calpain-7 protease functions together with the ESCRT-III protein IST1 within the midbody to regulate the timing and completion of abscission

The Endosomal Sorting Complexes Required for Transport (ESCRT) machinery mediates the membrane fission step that completes cytokinetic abscission and separates dividing cells. Filaments composed of ESCRT-III subunits constrict membranes of the intercellular bridge midbody to the abscission point. These filaments also bind and recruit cofactors whose activities help execute abscission and/or delay abscission timing in response to mitotic errors via the NoCut/Abscission checkpoint. We previously showed that the ESCRT-III subunit IST1 binds the cysteine protease Calpain-7 (CAPN7) and that CAPN7 is required for both efficient abscission and NoCut checkpoint maintenance. Here, we report biochemical and crystallographic studies showing that the tandem microtubule-interacting and trafficking (MIT) domains of CAPN7 bind simultaneously to two distinct IST1 MIT interaction motifs. Structure-guided point mutations in either CAPN7 MIT domain disrupted IST1 binding in vitro and in cells, and depletion/rescue experiments showed that the CAPN7-IST1 interaction is required for (1) CAPN7 recruitment to midbodies, (2) efficient abscission, and (3) NoCut checkpoint arrest. CAPN7 proteolytic activity is also required for abscission and checkpoint maintenance. Hence, IST1 recruits CAPN7 to midbodies, where its proteolytic activity is required to regulate and complete abscission.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2022

Characterizing Midcircuit Measurements on a Superconducting Qubit Using Gate Set Tomography

Measurements that occur within the internal layers of a quantum circuit—midcircuit measurements—are a useful quantum-computing primitive, most notably for quantum error correction. Midcircuit measurements have both classical and quantum outputs, so they can be subject to error modes that do not exist for measurements that terminate quantum circuits. In this work, we show how to characterize midcircuit measurements, modeled by quantum instruments, using a technique that we call quantum instrument linear gate set tomography (QILGST). We then apply this technique to characterize a dispersive measurement on a superconducting transmon qubit within a multiqubit system. By varying the delay time between the measurement pulse and subsequent gates, we explore the impact of residual cavity photon population on measurement error. QILGST can resolve different error modes and quantify the total error from a measurement; in our experiment, for delay times above 1000 ns we measure a total error rate (i.e., half diamond distance) of ϵ$\diamond$ = 8.1 ± 1.4%, a readout fidelity of 97.0 ± 0.3%, and output quantum-state fidelities of 96.7 ± 0.6% and 93.7 ± 0.7 % when measuring 0 and 1, respectively.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

A Fast-Response High-Accuracy Overvoltage Protection Circuit for Soft-Switching Current-Source Converters

Although voltage-source converters (VSCs) have been a focus of research for decades and are widely applied in numerous applications, they face great challenges in short-circuit failures, high dv/dt and electromagnetic interference (EMI), especially using wide bandgap devices. Instead, current-source converters (CSCs) are attracting increasing attention in recent years owing to their friendliness to short-circuit faults, improved EMI, etc. For CSCs, overvoltage is the most catastrophic failure since the semiconductor devices can hardly withstand an overvoltage for a short pulse. In this paper, a fast-response high-accuracy overvoltage protection (OVP) circuit is proposed to protect CSCs from overvoltage damage. It also features a small form factor, good noise-immunity, friendly retrofit capability, and no need for active switches. In this paper, the operating principle and design guideline of the proposed OVP circuit is introduced. Its effectiveness is validated in soft-switching solid-state transformer (S4T) at 500 V. In experiments, the voltage detection error of less than 5% and a propagation delay of fewer than 400 ns have been achieved.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2022

A distributed temperature profiling system for vertically and laterally dense acquisition of soil and snow temperature

Abstract. Measuring soil and snow temperature with high vertical and lateral resolution is critical for advancing the predictive understanding of thermal and hydro-biogeochemical processes that govern the behavior of environmental systems. Vertically resolved soil temperature measurements enable the estimation of soil thermal regimes, frozen-/thawed-layer thickness, thermal parameters, and heat and/or water fluxes. Similarly, they can be used to capture the snow depth and the snowpack thermal parameters and fluxes. However, these measurements are challenging to acquire using conventional approaches due to their total cost, their limited vertical resolution, and their large installation footprint. This study presents the development and validation of a novel distributed temperature profiling (DTP) system that addresses these challenges. The system leverages digital temperature sensors to provide unprecedented, finely resolved depth profiles of temperature measurements with flexibility in system geometry and vertical resolution. The integrated miniaturized logger enables automated data acquisition, management, and wireless transfer. A novel calibration approach adapted to the DTP system confirms the factory-assured sensor accuracy of ±0.1 ∘C and enables improving it to ±0.015 ∘C. Numerical experiments indicate that, under normal environmental conditions, an additional error of 0.01 % in amplitude and 70 s time delay in amplitude for a diurnal period can be expected, owing to the DTP housing. We demonstrate the DTP systems capability at two field sites, one focused on understanding how snow dynamics influence mountainous water resources and the other focused on understanding how soil properties influence carbon cycling. Results indicate that the DTP system reliably captures the dynamics in snow depth and soil freezing and thawing depth, enabling advances in understanding the intensity and timing in surface processes and their impact on subsurface thermohydrological regimes. Overall, the DTP system fulfills the needs for data accuracy, minimal power consumption, and low total cost, enabling advances in the multiscale understanding of various cryospheric and hydro-biogeochemical processes.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

THE EFFECT OF FUEL REACTIVITY AND EXHAUST GAS RECIRCULATION ON KNOCK PROPENSITY OF NATURAL GAS

The development of high efficiency, spark ignited natural gas engines is currently limited by engine knock at high compression ratio/elevated boost pressures and misfire at lean conditions/high exhaust gas recirculation (EGR) levels. The knock and misfire limits are further confounded by the wide variety in fuel reactivity observed in “pipeline quality” natural gas. In this study, a rapid compression machine was used to characterize the effects of EGR and variation in natural gas fuel reactivity on the homogeneous ignition delay, flame propagation rate, and end- gas autoignition propensity for stoichiometric natural gas/oxidizer/EGR blends. A reduced chemical kinetic mechanism was also developed to accurately model the homogeneous ignition delays measured in the Colorado State University rapid compression machine (CSU RCM). Pipeline quality natural gas with a range of chemical reactivity (68 < Methane Number < 95) was simulated using mixtures of CH4, C2H6, and C3H8. Exhaust gas recirculation gases were simulated with mixtures of Ar, CO2, CO, and NO at substitution rates of 0 to 30 mass percent. Ignition delay period under homogeneous autoignition conditions was measured at compressed pressures of 30.2 to 34.0 bar and compressed temperatures of 667 to 980 K. End-gas autoignition fraction and flame propagation rate were measured by initiating a laser spark in the center of the combustion chamber, after compression, at pressures of 30.7 to 32.7 bar and temperatures of 751 to 795 K. The results indicate that both fuel reactivity and the presence of reactive species (NO and CO) in the exhaust gas recirculation have a strong impact on end-gas autoignition fraction. A chemical kinetic mechanism was developed to predict homogeneous ignition delays for pipeline quality natural gas in a pressure and temperature range of 1-100 bar and 500-1000 K respectively. This mechanism accurately predicted measured homogeneous ignition delay in the RCM with a total average relative error of 11.0%.

Mohr, Jeffrey↗
DOE OSTI2025

Time-Varying Output Delay Compensation-A Model-Free Approach and its Application on Cooperative On-Ramp Merging

This paper presents a model-free approach to compensate for time-varying output delay in networked control systems. The proposed architecture combines a model-free observer and the Smith predictor. The model-free observer estimates the current state while handling modeling errors and uncertainties of the system. The Smith predictor moves the effect of time delay outside the control closed-loop using the estimated delayed output and the actual output of the plant. The proposed method is applied to a cooperative on-ramp merging problem. First, an ultra-local model predictive control is implemented to provide a computationally efficient online speed planner agnostic to the vehicle dynamics. After that, a model-free observer is designed to estimate the current state. Finally, the proposed architecture is tested against a time-varying output delay with an upper bound of 200 milliseconds. The results demonstrate the effectiveness of the proposed method with improved tracking of intervehicle distance.

Waleed khan, Muhammad [The University of Texas at ↗
DOE OSTI2022

Multimodal sensor fusion framework for residential building occupancy detection

For several years now, smart building energy systems have been a research area of intensive activity. In light of the increasing need for sustainable buildings and energy systems, this trend motivates an increasing need for a solution to reduce carbon dioxide emissions and improve energy efficiency. This work proposes a high-performing and transferable occupancy detection framework that combines sensor data from different data modalities, including time series environmental data (temperature, humidity, and illuminance), image data, and acoustic energy data using ensemble method. To draw out the best prediction performance in each modality, the proposed framework was developed, including various models that were designed to learn the occupancy patterns reflected in the physical data streams. To tackle the time series environmental data, we designed two variants of an occupancy detection spatiotemporal pattern network (Occ-STPN) that performs both feature level and decision level fusion, respectively. We also propose a new metric; the fading memory mean square error (FMMSE), that provides a fair evaluation and penalization of delayed occupancy predictions. Multiple open-sourced datasets, including the Electricity Consumption and Occupancy and the University of California, Irvine's (UCI) building occupancy detection dataset, along with our own real data collected from six different houses, were used to validate the algorithms' performance. The experimental results presented herein break down the performance for each sensing modality, and a detailed analysis of the performance is also discussed.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2020

Deep Lynx: Digital Engineering Integration Hub

The construction of megaprojects has consistently demonstrated challenges for project managers in regard to meeting cost, schedule, and performance requirements. Megaproject construction challenges are common place within megaprojects with many active projects in the United States failing to meet cost and schedule efforts by significant margins. Currently, engineering teams operate in siloed tools and disparate teams where connections across design, procurement, and construction systems are translated manually or over brittle point-to-point integrations. The manual nature of data exchange increases the risk of silent errors in the reactor design, with each silent error cascading across the design. These cascading errors lead to uncontrollable risk during construction, resulting in significant delays and cost overruns. Deep Lynx allows for an integrated platform during design and operations of mega projects.

Darrington, JohnW↗
DOE OSTI2023

SKS Polarization Anomalies Due to the Coriolis Force

The Earth’s Coriolis force has been well–known to impact surface waves and normal modes, which is essential to accurately interpret these waves. However, the Coriolis force on body waves has been assumed to be negligible and mostly ignored. It has been previously shown that the Coriolis force impacts polarizations of shear waves, whereas the wavefronts remain unaffected. We expand on the potential influences of Earth’s Coriolis force on shear–wave polarization measurements by conducting 3D numerical simulations for elastic waves generated by earthquake and explosive sources in a radially symmetric, and 3D mantle and crustal models. The Coriolis force can produce polarization anomalies of mantle shear waves up to 7° and core phases, such as SKS and SKKS, up to 4°. Uncorrected shear–wave polarizations due to the Coriolis force can cause an additional source of error (5°–10° in fast direction, and 0.2–0.3 s delay time depending on the method and seismic phase), inaccurate interpretation of station misalignments, and imprecise estimates of the core–mantle boundary topography. We show how to correct for the Coriolis force on teleseismic shear waves using 1D ray tracing for well–isolated phases. Here, we recommend the use of full waveform simulations to accurately account for earthquake sources parameters, poorly isolated phases that could include interfering phase arrivals within the measurement time window, and the effect of the Coriolis force on the polarizations of shear waves.

58 GEOSCIENCES↗
DOE OSTI2022

Addressing delayed case reporting in infectious disease forecast modeling

Infectious disease forecasting is of great interest to the public health community and policymakers, since forecasts can provide insight into disease dynamics in the near future and inform interventions. Due to delays in case reporting, however, forecasting models may often underestimate the current and future disease burden. In this paper, we propose a general framework for addressing reporting delay in disease forecasting efforts with the goal of improving forecasts. We propose strategies for leveraging either historical data on case reporting or external internet-based data to estimate the amount of reporting error. We then describe several approaches for adapting general forecasting pipelines to account for under- or over-reporting of cases. We apply these methods to address reporting delay in data on dengue fever cases in Puerto Rico from 1990 to 2009 and to reports of influenza-like illness (ILI) in the United States between 2010 and 2019. Through a simulation study, we compare method performance and evaluate robustness to assumption violations. Our results show that forecasting accuracy and prediction coverage almost always increase when correction methods are implemented to address reporting delay. Some of these methods required knowledge about the reporting error or high quality external data, which may not always be available. Provided alternatives include excluding recently-reported data and performing sensitivity analysis. This work provides intuition and guidance for handling delay in disease case reporting and may serve as a useful resource to inform practical infectious disease forecasting efforts.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2020

A Passivity-Shortage Based Control Design for Teleoperation With Time-Varying Delays

This letter investigates the effect of time-varying delays in bilateral teleoperation, with respect to stability and performance, using the properties of passivity-shortage. Until recently, the desired stability and performance characteristics were achieved using the concept of passivity. However, passivity is limited to systems of relative degree zero or one, while passivity-shortage includes systems of higher relative degrees and possibly of non-minimum phase. Passivity-shortage also arises naturally when data transmission is subject to delays, either constant or time-varying. In this letter, the properties of passivity-shortage are employed to design a simple negative feedback controller. We show that the proposed method provides a faster responding solution and improved performance compared to the existing approaches. The performance improvements include improved steady-state error convergence, and robustness against environmental disturbances, even in the presence of varying delays.

42 ENGINEERING↗
DOE OSTI2022

Simple Autoignition Model for the Derived Cetane Number of Oxygenated Compounds and Fuel Blends

A four-step autoignition model was used to derive an expression for the ignition delay and derived cetane number (DCN) measured by ignition quality testers (IQT) for oxygenated compounds and blends as a function of each compound’s global initiation and net chain branching rate constants. Expressions for these values were determined assuming they could be related to the functional groups present in a compound. Measurements for 124 compounds and 94 binary and ternary blends, gathered from the literature and performed at UW-Madison, were used to obtain the dependence of the measured ignition delay on each functional group. The new model was able to describe the ignition behavior of both the compounds and blends, with an average DCN error of 5.0 (22%) and 3.5 (15%), respectively. Additionally, the blend model was transformed into a mixing rule by incorporating existing IQT ignition delay data for each compound. Use of the mixing rule was found to offer improvements over the full prediction, with an average DCN error of 3.2 (14%).

Witkowski, Dustin↗