Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “YTTERBIUM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Accelerated oxidation during 1350°C cycling of ytterbium silicate environmental barrier coatings

We report environmental barrier coatings (EBCs) will be needed to protect SiC-based ceramic matrix composite components for the next generation of high-efficiency industrial gas turbines (IGTs). The IGT application will require ≥25 kh lifetimes, and little data are available on EBC failure mechanisms, particularly at ≥1300°C. Initial 1-h furnace cycle testing at 1350°C in 90 vol% H 2 O/10 vol% air was conducted ≥1000 cycles on thermally sprayed ytterbium disilicate (YbDS) coatings with and without an Si bond coating. By ≥1000 h, both EBCs formed thick, highly cracked, and fully crystalline cristobalite scales. Comparison of thermally grown oxide (TGO) microstructure and kinetics to isothermal rates of Si and SiC steam oxidation indicated a departure from slow-growing parabolic growth to more rapid rates of silica formation. Possible mechanisms and implications for this acceleration are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Plasmonics-enhanced photoconductive terahertz detector pumped by Ytterbium-doped fiber laser

We present a photoconductive terahertz detector operating at the 1 µm wavelength range at which high-power and compact Ytterbium-doped femtosecond fiber lasers are available. The detector utilizes an array of plasmonic nanoantennas to provide sub-picosecond transit time for the majority of photo-generated carriers to enable high-sensitivity terahertz detection without using a short-carrier-lifetime substrate. By using a high-mobility semiconductor substrate and preventing photocarrier recombination, the presented detector offers significantly higher sensitivity levels compared with previously demonstrated broadband photoconductive terahertz detectors operating at the 1 µm wavelength range. We demonstrate pulsed terahertz detection over a 4 THz bandwidth with a record-high signal-to-noise ratio of 95 dB at an average terahertz radiation power of 6.8 µW, when using an optical pump power of 30 mW.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS2011

Creep Behavior of Hafnia and Ytterbium Silicate Environmental Barrier Coating Systems on SiC/SiC Ceramic Matrix Composites

Environmental barrier coatings will play a crucial role in future advanced gas turbine engines because of their ability to significantly extend the temperature capability and stability of SiC/SiC ceramic matrix composite (CMC) engine components, thus improving the engine performance. In order to develop high performance, robust coating systems for engine components, appropriate test approaches simulating operating temperature gradient and stress environments for evaluating the critical coating properties must be established. In this paper, thermal gradient mechanical testing approaches for evaluating creep and fatigue behavior of environmental barrier coated SiC/SiC CMC systems will be described. The creep and fatigue behavior of Hafnia and ytterbium silicate environmental barrier coatings on SiC/SiC CMC systems will be reported in simulated environmental exposure conditions. The coating failure mechanisms will also be discussed under the heat flux and stress conditions.

Zhu, Dongming↗
NASA NTRS2012

Experimental Performance of a Single-Mode Ytterbium-doped Fiber Ring Laser with Intracavity Modulator

We have developed a linearly polarized Ytterbium-doped fiber ring laser with a single longitudinal mode output at 1064 run. A fiber-coupled intracavity phase modulator ensured mode-hop free operation and allowed fast frequency tuning. The fiber laser was locked with high stability to an iodine-stabilized laser, showing a frequency noise suppression of a factor approx 10 (exp 5) at 1 mHz

Numata, Kenji↗
NASA NTRS2015

Kinetic Monte Carlo Simulation of Oxygen Diffusion in Ytterbium Disilicate

Silicon-based ceramic components for next-generation jet turbine engines offer potential weight savings, as well as higher operating temperatures, both of which lead to increased efficiency and lower fuel costs. Silicon carbide (SiC), in particular, offers low density, good strength at high temperatures, and good oxidation resistance in dry air. However, reaction of SiC with high-temperature water vapor, as found in the hot section of jet turbine engines in operation, can cause rapid surface recession, which limits the lifetime of such components. Environmental Barrier Coatings (EBCs) are therefore needed if long component lifetime is to be achieved. Rare earth silicates such as Yb2Si2O7 and Yb2SiO5 have been proposed for such applications; in an effort to better understand diffusion in such materials, we have performed kinetic Monte Carlo (kMC) simulations of oxygen diffusion in Ytterbium disilicate, Yb2- Si2O7. The diffusive process is assumed to take place via the thermally activated hopping of oxygen atoms among oxygen vacancy sites or among interstitial sites. Migration barrier energies are computed using density functional theory (DFT).

Computer Simulation↗
NASA NTRSDate not supplied

Evaluation of Particle Degradation of a Ytterbium Disilicate Gas Turbine Coating in a Combustion Environment

Ytterbium disilicate (Yb2Si2O7) is a state-of-the-art topcoat material used in environmental barrier coatings (EBCs) to protect SiC-SiC composites from water vapor corrosion in gas turbine engines. However, it’s degradation by thermochemical and thermomechanical particle interactions may limit its use in next generation engine systems. Several static furnace tests have been performed on Yb2Si2O7 to elucidate methods of degradation, although dynamic testing in an engine-relevant environment has not been carried out. Ultimately, testing and evaluation of materials that incorporates all environmental damage modes will allow for an accurate assessment of long-term durability and operating lifetime. This work details the investigation of particle-induced erosion and corrosion of Yb2Si2O7 in NASA Glenn’s Erosion Burner Rig Facility. Coating durability was investigated as a function of test temperature, particle size, and deposition rate. Thermal cycling was also incorporated into testing to determine the interplay of heating/cooling cycles with particle degradation. Overall, these analyses will be used to determine coating robustness in an engine relevant environment.

Jamesa L Stokes↗
NASA NTRSDate not supplied

Evaluation of Particle Degradation of a Ytterbium Disilicate Gas Turbine Coating in a Combustion Environment

Ytterbium disilicate (Yb2Si2O7) is a state-of-the-art topcoat material used in environmental barrier coatings (EBCs) to protect SiC-SiC composites from water vapor corrosion in gas turbine engines. However, it’s degradation by thermochemical and thermomechanical particle interactions may limit its use in next generation engine systems. Several static furnace tests have been performed on Yb2Si2O7 to elucidate methods of degradation, although dynamic testing in an engine-relevant environment has not been carried out. Ultimately, testing and evaluation of materials that incorporates all environmental damage modes will allow for an accurate assessment of long-term durability and operating lifetime. This work details the investigation of particle-induced erosion and corrosion of Yb2Si2O7 in NASA Glenn’s Erosion Burner Rig Facility. Coating durability was investigated as a function of test temperature, particle size, and deposition rate. Thermal cycling was also incorporated into testing to determine the interplay of heating/cooling cycles with particle degradation. Overall, these analyses will be used to determine coating robustness in an engine relevant environment.

Jamesa L Stokes↗
DOE OSTI2024

The effect of cerium, neodymium, and ytterbium doping on UO 2 dissolution

Here, the dissolution rate of spent nuclear fuel has been studied heavily to understand the impacts of a failed waste package scenario on potential radionuclide release from a geologic repository. Multiple countries have evaluated these scenarios in oxidizing and reducing environments respective to their relevant repository conditions. The repository environment (e.g., water chemistry, temperature, oxygen content) and the fuel itself (e.g., chemical content of the fuel) both heavily impact the dissolution rate of the spent fuel. This work examined the impact that rare earth element dopants (Ce, Nd, Yb) have on the fuel dissolution under repository relevant conditions with decreasing oxidizing conditions using a single pass flowthrough system. UO 2 samples were doped with Ce, Nd, or Yb with concentrations between 1 and 5 at%. The addition of dopants to the samples reduced the dissolution rates on most samples relative to pure UO 2 samples. Scoping experiments that occurred in a less oxidizing environment showed a reduction in dissolution rate compared to fully oxidizing conditions. The results within highlight the importance of dopant behavior in used fuel dissolution modeling.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Crystal growth and scintillation properties of new ytterbium-activated scintillators Cs 4 CaI 6 :Yb and Cs 4 SrI 6 :Yb

Yb 2+ was investigated as a potential alternative activator for Cs 4 SrI 6 and Cs 4 CaI 6 scintillators for the first time, as opposed to the previously studied Eu2+ activator. Single crystals with nominal Yb 2+ concentrations of 0.5 mol%, 1 mol%, and 3 mol% were grown in Ø7 mm ampoules using the vertical Bridgman method. Luminescence and scintillation properties were evaluated as a function of Yb 2+ concentration and host compound. Here, the 5d → 4f electronic transition of Yb 2+ was observed for both the Sr- and Ca-containing compositions. X-ray induced radioluminescence emission was centered between 449 nm and 463 nm depending on Yb 2+ concentration and host compound. Both the spin-allowed and spin-forbidden transitions were observed in photoluminescence emission spectra and were centered at 446 nm and 476 nm, respectively, for both compounds. The best scintillation performance was achieved with Cs 4 CaI 6 :Yb 1 mol%, which had a 3.5% energy resolution at 662 keV and 43,000 ph/MeV light yield. To our knowledge this is the best energy resolution ever reported for a Yb 2+ -doped scintillator. Additional Cs 4 CaI 6 :Yb 1% crystals were grown in Ø12 mm ampoules to investigate the size dependence of scintillation properties, as well as crystal homogeneity.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Hydrothermal Synthesis and Solid-State Laser Refrigeration of Ytterbium-Doped Potassium-Lutetium-Fluoride (KLF) Microcrystals

Hydrothermal methods are used for the first time to synthesize distinct crystallographic stoichiometries within the potassium-lutetium-fluoride phase diagram for applications in solid-state laser refrigeration. Four crystalline phases were synthesized hydrothermally and doped with 10% Yb(III) ions, namely, orthorhombic K 2 LuF 5 (space group Pnma), trigonal KLuF 4 (space group P3 1 21), orthorhombic KLu 2 F 7 (space group Pna2 1 ), and cubic KLu 3 F 10 (space group $Fm\bar{3m}$), with each phase exhibiting unique microcrystalline morphologies. Among the four phases, the most significant cooling was observed for the KLuF 4 phase, which showed an overall refrigeration of 8.6 ± 2.1 K below room temperature. Laser refrigeration for KLuF4 was measured by observing both the eigenfrequencies of optomechanical cantilevers in vacuum and also the Brownian dynamics of optically trapped microcrystals in water. Cooling was also observed for the first time for the K 2 LuF 5 phase in vacuum based on measurements of the mean luminescence wavelength of Yb(III) ions. Finally, cooling was not observed with the other two phases.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Complex Adsorption Behavior of Neodymium and Ytterbium on Structurally-Distinct Alumina Surfaces

New sources of rare earth elements (REEs) are needed to support a green energy transition. REEs adsorbed to aluminum-rich clays in weathering deposits represent important resources but the mechanisms responsible for their retention and ease of extraction are unresolved. Disordered coordination and co-occurrence of multiple species pose challenges to investigating REE adsorption processes via established spectroscopic methods. In this study, we applied element-specific surface crystallography methods to obtain a new perspective on the complexity of REE adsorption mechanisms and affinities. Alumina (001) and (012) crystal surfaces were utilized to evaluate surface-specific controls on Nd(III) and Yb(III) adsorption behavior. The REEs displayed similar total adsorption to alumina (001) as a mixture of inner- and outer-sphere complexes, but Nd displayed a greater proportion of inner-sphere binding. Adsorption of ordered inner- and outer-sphere REE species was substantially lower on alumina (012). These distinct behaviors reflect differences in the surface functional group charging and topography of the two surfaces. However, alumina (012) also hosted a substantial population of disordered adsorbed species, especially for Nd, potentially associated with Al vacancy surface defects. Here, the accumulation of light versus heavy REEs via adsorption in weathering deposits likely results from multiple, competing reactions affected by clay particle morphology. Leaching procedures for resource recovery should account for differential rates of desorption by coexisting inner- and outer-sphere REE surface complexes.

58 GEOSCIENCES↗
DOE OSTI2024

Adsorption of Neodymium, Dysprosium, and Ytterbium to Goethite under Varying Aqueous Chemistry Conditions

The adsorption of rare earth elements (REEs) to iron oxides can regulate the mobility of REEs in the environment and is heavily influenced by water chemistry. This study utilized batch experiments to examine the adsorption of Nd, Dy, and Yb to goethite under varying pH, electrolyte (type and concentration), and concentrations of dissolved inorganic carbon and citrate. REE adsorption was strongly influenced by pH, with an increase from essentially no adsorption at pH 3.0 to nearly complete adsorption at pH 6.5 and higher. Citrate enhanced the adsorption of REEs at low pH (<5.0), likely by forming goethite-REE-citrate ternary surface complexes. However, citrate inhibited the adsorption of REEs at higher pH (>5.0) by forming aqueous REE-citrate complexes. Ionic strength had a small influence on REE adsorption, and the presence of dissolved inorganic carbon had no discernible effect. Equilibrium adsorption was interpreted with a triple-layer surface complexation model (SCM). The selection of surface complexation reactions was guided by extended X-ray absorption fine structure spectra. An SCM with a single bidentate inner-sphere surface complexation reaction for Nd and two inner-sphere surface complexation reactions (one monodentate and one bidentate reaction) for Dy and Yb effectively simulated adsorption across a broad range of conditions in the absence of citrate. Accounting for the effects of citrate on REE adsorption required the addition of up to two ternary REE-citrate-goethite surface complexes. The SCM can enable predictions of REE transport in subsurface environments that have goethite as an important adsorbent mineral. Furthermore, this predictive capability could contribute to identifying potential REE sources and facilitating efficient extraction of REEs.

58 GEOSCIENCES↗
DOE OSTI2021

Spatio-temporal ablation dynamics and plasma chemistry of aluminum induced by temporally modulated ytterbium fiber laser

Here, in this work, we studied single-pulse ablation dynamics of a temporally modulated continuous wave laser-material interaction with Al using in situ multimodal time-resolved diagnostics that describe in detail the associated physical and chemical processes. Time-resolved scattering, emission imaging, and optical emission spectroscopy unveiled a sequence of events spread out across three distinct phases: (i) early phase ablation process, associated with particle generation and liquid Al column formation (<20 μs), (ii) secondary detonation when sufficient ejected material is accumulated over the surface (20-50 μs), and (iii) molten liquid Al pool oscillation on the surface, followed by large droplet ejection from the liquid pool (100-500 μs). Atomic Al and AlO were observed with optical emission spectroscopy at different ratios during the entire lifetime of the event, verifying the formation of oxidized Al vapor upon its interaction with air. Morphological and compositional characterization confirmed surface oxidation and material re-solidification in the form of protrusions produced during the irradiation process. This work provides insights into the complex physical and chemical mechanisms of single-pulse ablation in the sub-millisecond laser pulse regime, which are critically important for parameter optimization in a variety of laser processing, microfabrication, and deposition applications.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Mechanisms of graphite ablation by sub-millisecond ytterbium fiber laser pulses

Graphite is a key material in a variety of cross-cutting applications in energy conversion, energy storage, and nuclear energy. Recently, temporally modulated continuous wave lasers have been shown to produce well-defined ablation features in graphite at relatively high processing speeds. In this work, we analyze in detail the laser ablation dynamics of single-pulse ablation in the sub-millisecond time regime to elucidate the origins of the resulting well-defined ablation craters using a combination of time-resolved emission imaging, diffuse reflection/scattering imaging, and optical emission spectroscopy. These multimodal in situ diagnostics revealed three main contributors to achieve well-defined ablation features: (1) rapid ejection of particles with ~100 m/s speed, (2) ablation of the graphite in the gaseous form, and (3) absence of bulk liquid motion, which is typically observed in laser processing of metals. Plasma plume formation was sustained throughout the duration of the laser pulse (500 μs). Here, this work provides insights into the complex physical and chemical mechanisms of sub-millisecond laser–matter interactions, which are critical for parameter space optimization and tailoring of laser machining and drilling processes.

42 ENGINEERING↗
DOE OSTI2025

Structure of molten ytterbium aluminum garnet

Rare earth aluminum garnets are important materials in optical, dielectric, and thermal barrier applications. To advance the understanding of their melt processing and glass forming ability, we report the atomic structure of molten Yb 3 Al 5 O 12 over 1770–2630 K, which spans the equilibrium and supercooled liquid regimes. The melt density at T m = 2283 K is 5.50 g cm –3 , measured via silhouette imaging of electrostatically levitated drops over 1010–2420 K. Four separate structure measurements were made with aerodynamically levitated melts using x-ray and neutron diffraction with isotope substitution of Yb ( 172 Yb, 174 Yb, or nat Yb). Empirical potential structure refinement models were developed, which are in excellent agreement with the experiments. Coordination environments for Al–O are predominantly 4- and 5-coordinate, with a mean coordination of n AlO = 4.43(8), while Yb–O environments mostly range from 5- to 8-coordinate, with n YbO = 6.26(8). The cation–oxygen polyhedra are connected primarily by corner-sharing, with edge-sharing constituting up to ~1/3 of the connectivity among polyhedra with Yb or higher-coordinated Al–O. Structurally, the –Al–O– network in molten Yb 3 Al 5 O 12 appears conducive to glass formation: n OAl = 1.85(3), there are 1.86 AlO x –AlO x connections per Al atom (e.g., a mixture of Q 3 and Q 4 units), and the modal ring size is six cations. These characterize a network that is somewhat less constrained compared to SiO 2 glass, yet Yb 3 Al 5 O 12 cannot be quenched into crystal-free glass. Here, aluminum garnet compositions with larger rare earth cations do form glass, so these characterizations help reveal the structural characteristics corresponding to the limit of glass forming ability in rare earth aluminates.

36 MATERIALS SCIENCE↗