Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “THERMAL DIFFUSION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Thermal diffusivity of diamond films using a laser pulse technique

Polycrystalline diamond films were deposited using a microwave plasma-enhanced chemical vapor deposition process. A laser pulse technique was developed to measure the thermal diffusivity of diamond films deposited on a silicon substrate. The effective thermal diffusivity of a diamond film on silicon was measured by observing the phase and amplitude of the cyclic thermal waves generated by laser pulses. An analytical model is presented to calculate the effective in-plane (face-parallel) diffusivity of a two-layer system. The model is used to reduce the effective thermal diffusivity of the diamonds/silicon sample to a value for the thermal diffusivity and conductivity of the diamond film. The average effective diffusivity values are 1.47 + or - 0.03 and 1.83 + or - 0.10 yielding thermal diffusivity values of 7.46 + or - 0.90 and 7.33 + or - 0.70 sq cm/s respectively, for the two samples; the calculated thermal con ductivity values are 13.50 and 13.28 W/cmK, which are better than that of type 1a natural diamond. The phase and amplitude measurements give similar results.

Albin, Sacharia↗
NASA NTRS1981

A remark on the theory of measuring thermal diffusivity by the modified Angstrom's method

A theory of the measurement of the thermal diffusivity of a sample by the modified Angstrom method is developed for the case in which radiative heat loss from the end surface of the sample is not negligible, and applied to measurements performed on lunar samples. Formulas allowing sample thermal diffusivity to be determined from the amplitude decay and phase lag of a temperature wave traveling through the sample are derived for a flat disk sample for which only heat loss from the end surface is important, and a sample of finite diameter and length for which heat loss through the end and side surfaces must be considered. It is noted that in the case of a flat disk, measurements at a single angular frequency of the temperature wave are sufficient, while the sample of finite diameter and length requires measurements at two discrete angular frequencies. Comparison of the values of the thermal diffusivities of two lunar samples of dimensions approximately 1 x 1 x 2 cm derived by the present methods and by the Angstrom theory for a finite bar reveals them to differ by not more than 5%, and indicates that more refined data are required as the measurement theory becomes more complicated.

Horai, K.-I.↗
NASA NTRS2000

Effect of Thermal Diffusivity on the Detectability of TNDE

The effect of thermal diffusively on the defect detectability in Carbon/Epoxy composite panels by transient thermography is presented in this paper. A series of Finite Element Models were constructed and analyzed to simulate the transient heat transfer phenomenon during Thermographic Non-destructive Evaluation (TNDE) of composite panels with square defects. Six common carbon fibers were considered. The models were built for composites with various combinations of fibers and volumetric ratios. Finite Element Analysis of these models showed the trends of the detectable range and the maximum thermal contrast versus the thermal diffusivity of various composites. Additionally, the trends of defect size to depth ratio and the thermal contrast has been investigated.

Zhao, Junduo↗
NASA NTRS2003

Thermophysical Properties of Te-based II-VI Semiconductors: Reduced Algorithms for Thermal Diffusivity Determination

This paper presents methodologies for measuring the thermal diffusivity using the difference between temperatures measured at two, essentially independent, locations. A heat pulse is applied for an arbitrary time to one region of the sample; either the inner core or the outer wall. Temperature changes are then monitored versus time. The thermal diffusivity is calculated from the temperature difference versus time. No initial conditions are used directly in the final results.

Banish, R. Michael↗
NASA NTRS1975

Thermal diffusivity measurements of particulates using the differentiated line source

A method is described in which thermal diffusivity measurements can be made on particulate materials using the identical instrumentation as described in previous papers for measuring thermal conductivity. The measurements for the two properties can be made simultaneously, thus eliminating the changes in conditions when they are made separately. This system has particular application for studies of simulated lunar, planetary, or asteroidal surfaces in which laboratory measurements can be correlated with astronomical observations of thermal inertia. A representative set of data is shown which gives thermal diffusivity and thermal conductivity measurements on a particulate basalt in which the values for each temperature were taken simultaneously. A value for specific heat is calculated for measurements taken at each temperature.

West, E. A.↗
NASA NTRS1992

Measuring Thermal Diffusivity Of A High-Tc Superconductor

Technique for measuring thermal diffusivity of superconductor of high critical temperature based on Angstrom's temperature-wave method. Peltier junction generates temperature oscillations, which propagate with attenuation up specimen. Thermal diffusivity of specimen calculated from distance between thermocouples and amplitudes and phases of oscillatory components of thermocouple readings.

Powers, Charles E.↗
NASA NTRS1984

Simple high-temperature thermal diffusivity apparatus

A simple and inexpensive thermal diffusivity apparatus is described for measurement up to 1600 K. The novel features of apparatus include a light pipe, a long furnace, and a differential thermocouple. A low heat-load sample holder for clamping the sample in a vertical position is also described. The results of measurements on AXM-5Q graphite are reported.

Wood, C.↗
DOE OSTI2025

In-Pile Irradiation Induced Defects and the Effect on Thermal Diffusivity of MgO

The effects of neutron irradiation temperature and dose on thermal diffusivity are compared between non-irradiated and in-pile irradiated MgO samples. MgO pellets were irradiated in-pile of the Advanced Test Reactor at Idaho National Laboratory. Samples were irradiated at 623 and 973 K to fast neutron fluences of 1 x 1025 (1.5 dpa) and 2 x 1025 n/m2 (3 dpa). Post irradiation examination included X-ray diffraction, scanning electron microscopy, laser flash thermal diffusivity, and transmission electron microscopy. The radiation induced thermophysical and structural evolution of MgO is reported

T. Moorea, Donald↗
NASA NTRS1987

Thermal diffusion in partially ionized gases - The case of unequal temperatures

Previous calculations of thermal diffusion coefficients in partially ionized gases are extended to the case of unequal neutral and ion temperatures and/or temperature gradients. Formulas are derived for the general case of a major gas as well as for minor atoms and ions. Strong enhancements of minor-ion thermal diffusion coefficients over their values in the fully ionized gas are found when the degree of ionization in the main gas is relatively low. However, compared to the case of equal temperatures, the enhancements are less strong when the neutrals are cooler than the ions. The specific case of the H-H(+) mixture, which is important in the study of solar and stellar atmospheres, is discussed as an application.

Geiss, J.↗
NASA NTRS2005

Calibration of High Temperature Thermal Conductivity System: New Algorithm to Measure Heat Capacity Using Flash Thermal Diffusivity in Thermoelectric Materials

A viewgraph presentation describing thermoelectric materials, an algorithm for heat capacity measurements and the process of flash thermal diffusivity. The contents include: 1) What are Thermoelectrics?; 2) Thermoelectric Applications; 3) Improving Thermoelectrics; 4) Research Goal; 5) Flash Thermal Diffusivity; 6) Background Effects; 7) Stainless Steel Comparison; 8) Pulse Max Integral; and 9) Graphite Comparison Algorithm.

heat capacity↗
NASA NTRS1978

Effect of diffusion-thermal processes on the high-latitude topside ionosphere

The extent to which diffusion-thermal heat flow affects H(+) temperatures in the high-latitude topside ionosphere is studied. Such a heat flow occurs whenever there are H(+)-O(+) relative drifts. From our study we have found that at high-latitudes, where H(+) flows up and out of the topside ionosphere, diffusion-thermal heat flow acts to reduce H(+) temperatures by 500-600 K at altitudes above about 900 km.

Schunk, R. W.↗
DOE OSTI2024

Measuring thermal diffusivity and gap conductance in uranium nitride and Zircaloy relevant for microreactor applications

Heat transfer across nuclear fuels and structural interfaces is an important factor for evaluating the performance of nuclear power systems. Specifically, heat generated as nuclear fuel fissions must be transported through the cladding material and through the reactor to reach the steam turbine for power generation. As new microreactor designs emerge, maximizing the efficiency of this heat transfer process becomes crucial to make them commercially viable. This article examines thermal diffusivity and gap conductance in uranium nitride (UN) fuel and Zircaloy-4 (Zry4) cladding using light flash analysis (LFA). Thermal diffusivity measurements were made on monolithic UN pellets and Zry4 exposed to carbon at peak operating temperatures of microreactors and show that carbon ingress has a minimal effect on thermal diffusivity when compared with identical materials not exposed to carbon. Evaluation of gap conductance at the UN-Zry4 interface was done using one-dimensional two-layer thermal transport models as a function of applied pressure. Here the results show that increasing pressure on the UN-Zry4 interface leads to gains in gap conductance per unit area in fuel-cladding assemblies at microreactor operating temperatures. While many other variables are expected to influence UN-Zry4 interfacial gap conductance (e.g. contact surface roughness, porosity, localized heating, environmental gas pressure), the work offers a demonstration of using a conventional LFA apparatus to determine this parameter at elevated temperatures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1976

Thermal diffusivity of four Apollo 17 rock samples

The modified Angstrom technique was used to measure the thermal diffusivity of four Apollo 17 rock samples in air at pressures of 1 atm and one-millionth torr in the temperature range 80-460 K, and in CO2 at different pressures for various temperature ranges and at different temperatures for the range of interstitial CO2 gas pressure 1 atm to 0.0001 torr. The experiments with CO2 were intended to simulate Martian conditions, and it was found that the thermal diffusivity of lunar crystalline basalt and breccia varies very little with temperature in a simulated Martian environment, which indicates that the thermal processes in the Martian regolith could be more straightforward than in the lunar regolith.

Horai, K.-I.↗
DOE OSTI2025

Femtosecond temperature measurements of laser-shocked copper deduced from the intensity of the x-ray thermal diffuse scattering

We present 50-fs, single-shot measurements of the x-ray thermal diffuse scattering (TDS) from copper foils that have been shocked via nanosecond laser ablation up to pressures above ∼135 GPa. We hence deduce the x-ray Debye–Waller factor, providing a temperature measurement. The targets were laser-shocked with the DiPOLE 100-X laser at the High Energy Density endstation of the European X-ray Free-Electron Laser. Single x-ray pulses, with a photon energy of 18 keV, were scattered from the samples and recorded on Varex detectors. Despite the targets being highly textured (as evinced by large variations in the elastic scattering) and with such texture changing upon compression, the absolute intensity of the azimuthally averaged inelastic TDS between the Bragg peaks is largely insensitive to these changes, and allowing for both Compton scattering and the low-level scattering from a sacrificial ablator layer provides a reliable measurement of $T/Θ^2_D$, where Θ D is the Debye temperature. We compare our results with the predictions of the SESAME 3336 and LEOS 290 equations of state for copper and find good agreement within experimental errors. We, thus, demonstrate that single-shot temperature measurements of dynamically compressed materials can be made via thermal diffuse scattering of XFEL radiation.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗