Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “RSI”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

Adhesives for bonding RSI tile to GrPI structure for advanced space transportation systems

A system was developed for bonding RSI tiles to a graphite/polymide composite substrate which would withstand the full range of environmental conditions. The bonding system, designated RA59, consists of a mixture of glass (sesquisiloxane) resin in RTV 560 silicone. A significant number of data points for the RA59 are in the 65-psi failure range both when tested, and after exposure to 700 F. This is over two times the best shear and tensile values obtained with RV60 at this temperature. It is concluded that with a thorough understanding of the critical parameters involved, the higher values should be obtained consistently with the RA59. This is of particular significance if higher strength tiles were to be used in a hard-bonded configuration.

Smith, K. E.↗

Improvement of Reusable Surface Insulation (RSI) materials

The mullite fiber based hardened compacted fibers (HCF) type of reusable surface insulation was further developed for use in the Space Shuttle Program. Two hundred fifty formulations of fiber mixtures, fillers, binders, and organic processing aids were made using mullite fibers as the basic ingredient. Most of the work was accomplished on 15-lb/cu ft material. It was established that higher density materials are stronger with strength values as high as 250 lb/sq in. in tension. New measurement techniques and equipment were developed for accurate determination of strength and strain to failure. Room temperature to 2300 F stress-strain relationships were made. The room temperature tensile modulus of elasticity is 61,700 lb/sq in. and the strain at failure is 0.165 percent, typically, when measured longitudinally parallel to the long axes of the fibers. Thermal insulating effectiveness was increased 20 percent by reducing the diameter of some of the fibers in the material. Improvements were made in density uniformity and strength uniformity in a block of HCF by mixing improvements and by the use of organic additives. Specifications were established on the materials and processes used in making the insulation.

Blome, J. C.↗

Silica RSI Morphology and Properties

The morphology of all silica materials studied has been noncrystalline and resistant to any phase transformations upon subsequent thermal testing representative of the shuttle environment envelope. The development of an extremely dependable reusable surface insulation material family offering the inherently superior characteristics of amorphous silica for the shuttle is described.

Beasley, R. M.↗

Evaluation of RSI Materials

Novel attachment and strain-measuring techniques were developed to obtain valid mechanical and thermophysical property data to above 1530 K in air on nonmetallic insulators and their coatings. The lever-arm extensometer developed used for measuring thermal and/or mechanical strain. Thermal expansion measurements were made on a tensile load to define their softening points. Creep characteristics of the insulators were monitored at elevated temperatures and found to become significant above 1090 K (1500 F).

Kistler, C. W.↗

Aerodynamic simulation tests of RSI panels

The technique of mixing argon with air was used to simulate the temperature-time trajectory experienced by space shuttle vehicle insulation panels. Gap heating appears to be highly dependent upon gap design, it is relatively low for interlocking and tapered panel designs and significantly higher for a wider, unfilled gap design. The heating rate appears to be significantly higher at the windward facing edges of flush tiles and is aggravated at forward facing steps. This heating, however, is highly dependent on step heights relative to some characteristic thickness of the boundary layer.

Centolanzi, F. J.↗

Cyclic arc plasma tests of RSI materials using a preheater

The results of a test program are reported in which a preheater was used with an arc plasma stream to study the thermal response of samples of candidate reusable surface insulation materials for the space shuttle. The preheater simulated the shuttle temperature history during the first and last portions of the test cycle, which could not be simulated by the air arc plasma flow. Pre- and post-test data taken for each of the materials included magnified views, optical properties, and chemical analyses. The test results indicate that the mullite base samples experience higher surface temperatures than the other materials at heating rates greater than 225 kw/sq m. The ceramic fibrous mullite and silica coatings show noncatalytic wall behavior. Internal temperature response data for the materials are compared and correlated with analytical predictions.

Stewart, D. A.↗

Arc jet tests of RSI materials: Screening and comparative evaluation

Cyclic convective heating test results show that all surface insulation materials tested exhibit a wide range of surface emittance and catalytic activity depending on their surface coatings. Coatings have a significant effect on the overall material response depending on boundary layer characteristics.

Schaefer, J. W.↗

Characterization of RSI coating

X-ray diffraction analyses on mullite, silica, and ceramic mullite fiber coating materials to investigate the effects of thermal cycling, show that ceramic mullite fiber coating porosity is little affected by cycling to 1250 C and that material pores are mostly smaller than 15 nm. Some mullite coatings experience a slight increase in crystobalite with somewhat increased porosity. Silica coatings show a marked tendency to precipitate cristobalite with increased porosity and dimensional instability.

Miller, A. D.↗

Silica RSI for Application to the Shuttle Orbiter

Silica reusable surface insulation is analyzed for its cold soak properties, bond properties at low temperature, gap and step heating effects, and aerodynamic surface roughness effects to determine space shuttle weight and cost sensitivity to structure subsystem weights. Computerized simulation studies show that total program cost savings of silica (vs. mullite) exceed thermal protection system design and development costs and that an early introduction of silica increases total program cost savings.

Forsberg, K. J.↗

Results of RSI Thermal-structural Analysis

Thermostructural comparisons of mullite and silica reusable surface insulation materials for space shuttle application show that mullite is much more subject to thermal stress failure than silica composite materials.

Pigg, O. E.↗

Interference Heating to Cavities Between Simulated RSI Tiles

Test results for full scale simulated surface insulation tiles on both the tunnel wall and in the free stream, for in-line and staggered tile orientations, are summarized as follows: (1) The staggered tile orientation has heating on the forward face which is a factor of 4.5 times higher than the heating to the forward face of the in-line tile orientation; (2) the longitudinal gap heating was the highest for the 0.3175 cm gap and the lowest for the 0.1587 cm gap; and (3) there was an order of magnitude decrease in the heating on the forward face of a spanwise gap when the gap size was decreased from 0.3175 cm to 0.1587 cm.

Johnson, C. B.↗

Effect of Cristobalite on the Mechanical Properties of Silica RSI Materials

The strength of various silica surface insulation materials was measured after high temperature heat treatment to develop substantial crystalline phases, and after low temperature thermal cycling through the alpha-beta cristobalite transformation. It appears that the presence of cristobalite in the structural elements (the fibers) is highly detrimental to tensile strength. When crystallization does not occur in silica material, the strength improves with heat treatment.

Khandelwal, P. K.↗

Emittance of RSI Coatings Determined from Radiation Measurements in Arc Jet Tests

Simultaneous measurements were made on three surface insulation coatings for total surface radiation and radiation at discrete wavelengths between 0.88 and 4.5 microns. The mullite coating radiated all the applied heat at convective heat rates of 204 and 295 kw/sq m. Radiation from the ceramic mullite fiber coating was 170 kw/sq m at a heat rate of 454 kw/sq m. Effective total emissivity and spectral emissivity values were evaluated; all three coatings were significantly non-grey. Effective total emissivity values were 0.79 for mullite, 0.50 for ceramic mullite fiber, and 0.78 for silica composite.

Wakefield, R. M.↗

Data correlation and analysis of arc tunnel and wind tunnel tests of RSI joints and gaps. Volume 1: Technical report

Heat transfer data measured in gaps typical of those under consideration for joints in space shuttle reusable surface insulation protection systems have been assimilated, analyzed and correlated. The data were obtained in four NASA facilities. Several types of gaps were investigated with emphasis on simple butt joints. Gap widths ranged from 0.07 to 0.7 cm and depths ranged from 1 to 6 cm. Laminar, transitional and turbulent boundary layer flows over the gap opening were investigated. Three-dimensional heating variations were observed within gaps in the absence of external flow pressure gradients. Heat transfer correlation equations were obtained for several of the tests. Thermal protection system performance with and without gaps was compared for a representative shuttle entry trajectory.

Christensen, H. E.↗

Supersonic stability and control characteristics of a 0.015 scale model 69-0 of the space shuttle orbiter with forebody RSI modifications in the NASA/LaRC 4-foot UPWT (legs 1 and 2) (LA71A/B)

Investigations are reported for the determination of aerodynamic effects of reducing the thickness of the reusable surface insulation located along the sides of the shuttle orbiter in order to allow weight reduction in the nose region. Six-component aerodynamic force and moment data were obtained at Mach numbers from 1.5 to 4.6 over an angle of attack range from about -1 deg to 28 deg. Additional tests were made over an angle of sideslip range from -6 deg to 6 deg at selected angles of attack. Test results are presented in graph and tables.

Source record↗