SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
2H SnSe 2 and 1T VSe 2 van der Waals materials were synthesized and then subjected to redox exfoliation. Decoration of these 2D sheets with iron oxide nanoparticles produced a synergistic magnetization response that exceeded that of iron oxide alone.
The creation and exploration of new materials under extreme pressure–temperature conditions has become increasingly reliant on laser-heated diamond anvil cell (LHDAC) techniques, which provide direct access to previously unexplored regions of multinary phase diagrams. Whereas numerous high-pressure phases have been identified in situ, systematic recovery and post-synthesis physical property characterization of these materials remain significant challenges. In this work, we describe the setup and implementation of an LHDAC-based synthesis and recovery workflow and demonstrate its application to metastable MnSb 2 and YbZn 2 phases. Synchrotron x-ray diffraction and spatial mapping confirm dominant formation of the targeted phases, whereas laboratory-based refinement quantifies phase fractions despite intrinsic microstrain and minor secondary phases. High-pressure transport measurements on recovered samples reveal pressure-tunable electronic instabilities in both systems. In MnSb 2 , pressure suppresses two high-temperature magnetic ordering anomalies, observed in transport, by ∼5 GPa and, for higher pressures, induces a new low-temperature feature that increases with further pressure increase. In hexagonal high-pressure YbZn 2 , an electronic reconstruction emerges at ∼11 GPa, characterized by semiconducting-like behavior from ∼30 to 300 K and a broad low-temperature coherence crossover near 30 K. Our results establish LHDAC synthesis not only as a structural discovery tool but also as an experimental platform for investigating correlated quantum states stabilized far from equilibrium thermodynamic conditions.
A facile, scalable, wastewater-free synthesis of high energy density LiMn0.5Fe0.5PO4 (LMFP) cathodes with high electrode press density is achieved by employing the spinel LiMnFeO4 (LMFO) as a precursor.
We demonstrate that applying modest magnetic fields (< 0.1 T) during high-temperature crystal growth can profoundly alter the structure and ground state of a spin-orbit-coupled, antiferromagnetic trimer lattice. Using BaIrO₃ as a model system, whose ground state is intricately dictated by the trimer lattice, we show that magneto-synthesis , a field-assisted synthesis approach, stabilizes a structurally compressed, metastable metallic and magnetically suppressed phases inaccessible via conventional methods. These effects include a 0.85% reduction in unit cell, 4-order-of-magnitude decrease in resistivity, a 10-fold enhancement of the Sommerfeld coefficient, and the collapse of long-range magnetic order -- all intrinsic and bulk in origin. First-principles calculations confirm that the field-stabilized structure lies substantially above the ground state in energy, highlighting its metastable character. These large, coherent and correlated changes across multiple bulk properties, unlike those caused by dilute impurities, defects or off-stoichiometry, point to an intrinsic field-induced mechanism. The findings establish magneto-synthesis as a powerful new pathway for accessing non-equilibrium quantum phases in strongly correlated materials.
Controlling the size of iron oxide nanoparticles while maintaining uniformity in flow-based synthesis systems has been a great challenge in nanoparticle synthesis. Using an extended LaMer mechanism, we improve both the size and shape uniformity as compared to a conventional flow synthesis. The key to this approach is the injection of additional Fe precursor during the flow reaction, providing extra precursor during the growth process leading to a size focusing step. This approach has also allowed for the systematic variation of the nanoparticle size produced in the flow reaction. This work represent a new synthetic concept for improving the size uniformity of iron oxide nanoparticles in flow-based synthesis and has potential for application across a wide range of nanoparticle systems.
There have been relatively few publications examining the role of gravity during combustion synthesis (CS), mostly involving thermite systems. The main goal of this research was to study the influence of gravity on the combustion characteristics of heterogeneous gasless systems. In addition, some aspects of microstructure formation processes which occur during gasless CS were also studied. Four directions for experimental investigation have been explored: (1) the influence of gravity force on the characteristic features of heterogeneous combustion wave propagation (average velocity, instantaneous velocities, shape of combustion front); (2) the combustion of highly porous mixtures (with porosity greater than that for loose powders), which cannot be obtained in normal gravity; (3) the effect of gravity on sample expansion during combustion, in order to produce highly porous materials under microgravity conditions; and (4) the effect of gravity on the structure formation mechanism during the combustion synthesis of poreless composite materials.
Energetic norbornenes are promising candidates toward the development of new energetic polymers due to the synthetic versatility of norbornene ring-opening metathesis polymerizations used in commercial applications. We report the synthesis of two energetic norbornene materials that can be made in two steps with modest yields, containing either trinitroethanol or fluorodinitroethanol substituents. The norbornene monomers were then polymerized, and the polymers were characterized by Fourier transform infrared spectroscopy (FT-IR), differential scanning calorimetry (DSC), contact angle measurements, and proton and carbon nuclear magnetic resonance spectroscopies ( 1 H and 13 C{ 1 H} NMR). Additionally, small-scale safety data consisting of electrostatic discharge (ESD), friction (FS), and impact (IS) sensitivities were measured for the norbornene monomers and their resulting polymers. These analyses revealed that energetic norbornene materials are relatively insensitive and have densities comparable to that of TNT (1.47–1.81 g·cm –3 ).
The next generation of advanced materials is tending toward increasingly complex compositions. Synthesizing precise composition is time-consuming and becomes exponentially demanding with increasing compositional complexity. An experienced human operator does significantly better than a novice but still struggles to consistently achieve precision when synthesis parameters are coupled. The time to optimize synthesis becomes a barrier to exploring scientifically and technologically exciting compositionally complex materials. This investigation demonstrates an active learning (AL) approach for optimizing physical vapor deposition synthesis of thin-film alloys with up to five principal elements. We compared AL-based on Gaussian process (GP) and random forest (RF) models. The best performing models were able to discover synthesis parameters for a target quinary alloy in 14 iterations. We also demonstrate the capability of these models to be used in transfer learning tasks. RF and GP models trained on lower dimensional systems (i.e., ternary, quarternary) show an immediate improvement in prediction accuracy compared to models trained only on quinary samples. Furthermore, samples that only share a few elements in common with the target composition can be used for model pre-training. We believe that such AL approaches can be widely adapted to significantly accelerate the exploration of compositionally complex materials.
Under this agreement, Laminar will loan Argonne a 50L Taylor Vortex Reactor (TVR) and provide mechanical troubleshooting guidance and consulting to ensure the successful setup of the pilot-scale synthesis process. The U.S. Department of Energy (DOE) will allocate funding for the labor and materials required for the study. To evaluate the physical and electrochemical properties of the materials produced by the 50L TVR, Argonne will perform comprehensive characterizations, including XRD, SEM, PSA, ICP, tap density, and coin half-cell testing. Throughout the collaboration, Argonne will provide feedback and recommendations for mechanical improvements to the reactor system. Furthermore, Argonne will credit Laminar as a collaborator in any presentations or publications resulting from data generated by the system. Laminar will retain no rights to experimental results or intellectual property generated through the experiments conducted with the 50L TVR at Argonne.
Flexible polyurethane foams are a diverse class of materials encompassing furniture, packaging, automotive, and many other industrial and domestic applications. Polyurethane foams are synthesized by the addition of polyols and isocyanates; however, the petroleum origin and toxic nature of isocyanates have driven many to look for more sustainable routes to production. Renewable fillers have emerged as a biobased resource to decrease the carbon footprint of this widely used polymeric material. In this study, soy hulls, as mass-produced, industrial by-products of soybean production, were used to create a biochar beneficial in the synthesis of flexible polyurethane foam composites. The addition of soy hull biochar was found to maintain the compression properties of foams at a decreasing isocyanate index, reducing the amount of isocyanates needed for production. In addition, the addition of biochar decreased the flammability of foams, important for many applications where consumer safety is important. The results point to the ability to create safer, more sustainable, and even more cost-effective polyurethane foams through the reduction in isocyanate use while maintaining the properties of this important class of polymers.
Conventional preparation of supported bimetallic catalysts relies on solution-mediated metal salt immobilization and pre-formation of alloy nanoparticles before reaction. Here, we report a fundamentally different synthesis strategy of using a physical mixture of salt precursors to generate an active catalyst during reaction. The catalytic structure is generated in situ from Pd3(OAc)6, Au(OH)3, and KOAc through H2 treatment and reaction-driven restructuring under vinyl acetate monomer (VAM) synthesis conditions. Ascertained from in situ X-ray diffraction and operando infrared spectroscopy analyses, reduction treatment produces segregated Pd and Au domains, and subsequent exposure to a VAM reaction mixture triggers dynamic extraction of Pd from the metal surface. This latter process, mediated by acetate-assisted redox cycles, facilitates Pd migration toward Au domains to form a near-surface localized Pd50Au50 alloy phase. Monometallic Pd domains serve as a reservoir of Pd to the alloy phase, leading to and sustaining a more Pd-enriched active surface and a higher population of accessible Pd sites, compared to a conventionally prepared K-PdAu/SiO2 catalyst. Consequently, this leads to a twofold increase in the VAM formation rate, demonstrating highly active bimetallic catalysts can be generated through the gas-phase treatment of physically mixed ionic precursors.
Sol–gel synthesis is a wet-chemical processing route for fabricating functional materials with control over composition and microstructure at relatively low temperatures compared to conventional solid-state synthesis. While sol–gel process initiates with intermixed molecular precursors, the early-stage nucleation pathways are insufficiently understood. Here, in this study, the chemical and structural transformation of ion disordered rocksalt (DRX) Li 1.2 Mn 0.4 Ti 0.4 O 2 (LMTO), a promising cathode material for lithium batteries, is studied by multiscale characterizations. In situ heating transmission electron microscopy (TEM) using a liquid cell visualizes and identifies crystallization pathways at the nanoscale. While some regions follow a classical multi-step transition through thermodynamically stable intermediates, others exhibit a kinetic shortcut via a localized amorphous matrix to directly form the DRX structure. Macroscale Fourier transform infrared spectroscopy corroborates the findings and reveals that transition metal ions are more strongly incorporated into the acetate-coordinated network than lithium. Although in situ heating TEM captures diverse local transformation pathways, in situ synchrotron X-ray diffraction indicates that the macroscopic transformation proceeds predominantly through spinel LMTO and lithium titanates toward DRX-LMTO. The findings uncover the spatiotemporal chemical and structural transformations in sol–gel derived DRX-LMTO materials, and call for fine-tuning of such sol–gel chemistries to manipulate the crystallization pathways and achieve target material homogeneity more efficiently.
This research explores the effect of a composite support of SiO2 and Al2O3 with Fe and Co incorporated as catalysts for Fischer–Tropsch synthesis (FTS) using a 3D-printed stainless steel (SS) microchannel microreactor. Two mesoporous catalysts, FeCo/SiO2Al2O3 and Co/SiO2Al2O3, were synthesized via a one-pot (OP) method and extensively characterized using N2 physisorption, XRD, SEM, TEM, H2-TPR, TGA-DSC, FTIR, and XPS. H2-TPR results revealed that the synthesis method significantly affected the reducibility of metal oxides, thereby influencing the formation of active FTS sites. SEM-EDS and TEM further revealed a well-defined hexagonal matrix with a porous surface morphology and uniform metal ion distribution. FTS reactions, carried out in the 200–350 °C temperature range at 20 bar with a H2/CO molar ratio of 2:1, exhibited the highest activity for FeCo/SiO2Al2O3, with up to 80% CO conversion. Long-term stability was evaluated by monitoring the catalyst performance for 30 h on stream at 320 °C under identical reaction conditions. The catalyst was initially active for the methanation reaction for up to 15 h, after which the selectivity for CH4 declined. Correspondingly, the C4+ selectivity increased after 15 h of time-on-stream, indicating a shift in the product distribution toward longer-chain hydrocarbons. This trend suggests that the catalyst undergoes gradual activation or restructuring under reaction conditions, which enhances chain growth over time. The increase in C4+ products may be attributed to the stabilization of the active sites and suppression of methane or light hydrocarbon formation.
Synthetic aperture imaging has enabled breakthrough observations from radar to astronomy. However, optical implementation remains challenging due to stringent wavefield synchronization requirements among multiple receivers. Here we present the multiscale aperture synthesis imager (MASI), which utilizes parallelism to break complex optical challenges into tractable sub-problems. MASI employs a distributed array of coded sensors that operate independently yet coherently to surpass the diffraction limit of single receiver. It combines the propagated wavefields from individual sensors through a computational phase synchronization scheme, eliminating the need for overlapping measurement regions to establish phase coherence. Light diffraction in MASI naturally expands the imaging field, generating phase-contrast visualizations that are substantially larger than sensor dimensions. Without using lenses, MASI resolves sub-micron features at ultralong working distances and reconstructs 3D shapes over centimeter-scale fields. MASI transforms the intractable optical synchronization problem into a computational one, enabling practical deployment of scalable synthetic aperture systems at optical wavelengths.
This study presents a one-pot synthesis route to organometallic nanofibers based on copper thiolate, exhibiting distinctive chemical and physical characteristics. Electron microscopy analysis of morphology and composition revealed 2-10 μm-long, 50-90 nm-diameter hollow and non-hollow fibers composed of copper, sulfur, oxygen, hydrocarbon, and chlorine. Thermogravimetric analysis showed a pronounced mass loss within 120°C-135°C. To elucidate the thermal responsive pathways, the nanofibers were characterized before and after heating. X-ray photoelectron spectroscopy indicates that an initially mixed Cu(I)/Cu(II) oxidation states transition to predominantly Cu(I) upon heating. A layer of nanofiber was coated on battery pouch foil and evaluated as a candidate thermally sensitive coating. At elevated temperature (100-130°C), nanofiber coating released volatile organic compounds, sulfide and sulfur dioxide as detected using multiple gas sensors. This thermally responsive gas release/sensing approach provides a potential large-area temperature monitoring strategy, which is particularly relevant where direct temperature measurements of individual batteries is impractical. The results established proof of concept for nanofiber-coated battery pouch foil as overtemperature warning platform that can provide alerts when surface temperatures exceed a critical threshold. More broadly, the ability to form interconnected fiber networks positions copper thiolate nanofiber coatings as promising materials for advanced applications.
Cost-effective and scalable synthesis of single-crystal lithium–metal-oxide cathodes with controlled size and morphology remains challenging for advancing high-performance lithium-ion batteries. Here, we demonstrate a solution combustion–assisted solid-state method for producing single-crystal NMC622 with tunable particle size at various lithium stoichiometries. Structural and electronic characteristics were probed using synchrotron-XANES, EXAFS, XRD and XPS, confirming well-defined coordination environments and phase purity up to Li ≈ 1.3. The electrochemical behavior of LixNMC (x = 1.0 and 1.3) single crystals was evaluated across 2.8–4.3 V and 2.8–4.7 V windows to elucidate the effects of lithium content and operating voltage. At 2.8–4.3V, Li1.3NMC exhibits higher initial capacity due to its larger lithium inventory, while Li1.0NMC shows superior long-term retention driven by its larger crystal size and reduced structural distortion. Increasing the cutoff voltage to 4.7 V enhances the initial capacity of both compositions by 17–25%, but long-term capacity retention ultimately converges to values comparable to those at 4.3 V due to voltage-induced degradation, where Li+ diffusion constant remains lying ranging from 10−12 –10−11 cm2s−1. Overall, this study establishes a scalable combustion-assisted route for synthesizing tunable single-crystal NMC622 and highlights the interplay between lithium stoichiometry, particle size, and voltage window in governing cathode stability.
Sodium-ion batteries (SIBs) are a sustainable alternative to lithium-ion systems for global electrification, with O3-type layered oxide cathodes offering high specific capacity and feasibility of scalable synthesis. Industrial co-precipitation synthesis of these cathodes typically uses transition metal sulfates, requiring extensive water rinsing to remove Na 2 SO 4 impurities, a process that consumes significant water and risks residual inactive phases if incomplete. Here, this work introduces a rinse-free, resource-efficient approach using metal acetate precursors. Residual sodium acetate in non-rinsed precursors decomposes during sintering to generate Na 2 CO 3 in situ, partially substituting an external sodium resource (e.g., NaOH and Na 2 CO 3 ) and reducing its consumption by ∼18–20%. Phase-pure O3-Na 1.0 Ni 1/3 Fe 1/3 Mn 1/3 O 2 (NFM111) cathodes synthesized via this method exhibit microstructure and electrochemical performance comparable to rinsed sulfate-derived counterparts, with initial capacities of 141 mAh g −1 at C/20 (7.5 mA g −1 ). By eliminating rinsing and minimizing sodium reagent use, this acetate-based route enhances sustainability and scalability of layered oxide production for SIBs.
In recent years, graphene-type materials originating from metal–organic frameworks (MOFs) or integrated with MOFs have exhibited notable performances across various applications. However, a comprehensive understanding of these complex materials and their functionalities remains obscure. While some studies have reviewed graphene/MOF composites from different perspectives, due to their structural–functional intricacies, it is crucial to conduct more in-depth reviews focusing on specific sets of graphene/MOF composites designed for particular applications. In this review, we thoroughly investigate the syntheses, characteristics, and performances of N-G/MOF(ZIF-8)-based/derived materials employed in electrochemical energy conversion and storage systems. Special attention is given to realizing their fundamental functionalities. The discussions are divided into three segments based on the application of N-G/ZIF-8-based/derived materials as electrode materials for batteries, electrodes for electrochemical capacitors, and electrocatalysts. As electrodes for batteries, N-G/MOF(ZIF-8) materials can mitigate issues like an electrode volume expansion for Li-ion batteries and the ‘shuttle effect’ for Li-S batteries. As electrodes for electrochemical capacitors, these materials can considerably improve the ion transfer rate and electronic conductivity, thereby enhancing the specific capacitance while maintaining the structural stability. Also, it was observed that these materials could occasionally outperform standard platinum-based catalysts for the electrochemical oxygen reduction reaction (ORR). The reported electrochemical performances and structural parameters of these materials were carefully tabulated in uniform units and scales. Through a critical analysis of the present synthesis trends, characteristics, and functionalities of these materials, specific aspects were identified that required further exploration to fully utilize their inherent capabilities.