Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Material extrusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Reduced-order CFD modeling of cryogenic hydrogen isotope extrusion for pellet fueling

This study presents a reduced-order model (ROM) for computational fluid dynamics (CFD) simulations of cryogenic hydrogen isotope extrusions, focusing on protium (H₂) and deuterium (D₂) piston extruders. Using a 2D axisymmetric ROM in ANSYS-Polyflow, significant computational savings were achieved (runtime reduced from 9∼24 h to 3∼5 min), with extrusion force discrepancies between the 2D ROM and 3D models being on the order of 1%. Parametric studies identified optimal cutoff shear rates in the viscosity model (0.01/s for H₂ and 0.001/s for D₂), providing recommendations for future simulations. Finally, a comprehensive comparison of ROM results with experimental data was performed across varying geometries, cryogenic materials, temperatures, extrusion lengths, and piston velocities. Predictions at low extrusion temperatures met the objective of providing quick and efficient solutions with an acceptable extrusion force error of approximately 10% or less, validating the effectiveness of the 2D ROM approach. However, at high temperatures closer to the triple point, extrusion force error grows, which necessitates developing an improved model that accounts for temperature effects, e.g. melting. Nevertheless, the findings still represent a significant improvement in efficiency of CFD modeling of cryogenic hydrogenic extrusion. The ROM framework can also be extended to tritium (T2) and screw extruders, which will ultimately provide a fast and effective tool for optimizing pellet injector design for ITER and future reactor systems.

Fan, Joy [ORNL] (ORCID:0000000229751735)↗
DOE OSTI2025

Development of a Printable Prill Formulation Technique and Demonstration of Monomodal Prill Size on Compaction Density and Compressive Strength

Polymer-bonded explosive molding powder, or “prills,” are relied on for the fabrication of pressed high explosives since the 1950's. The wet granulation technique, also known as “slurry coating,” that is used to formulate prills, is a complex process that results in polydisperse and variable yields. This makes it difficult to study the mesoscale effect that prills have on the microstructure of a pressed article. The following study introduces a novel approach to energetic granulation that leverages techniques used in the additive manufacturing of paste-like energetic materials. This extrusion granulation, or prill printing technique, makes it possible to tailor the sizes and shapes of prills, allowing for their morphological influences to be studied in a controlled manner. The following work details the fabrication and characterization of four monomodal size lots of prills using an inert formulation (95 wt.% melamine, 5 wt.% polymer binder). Prills from each size lot were die-pressed using a fixed recipe to investigate how prill size impacts compaction density and therefore compressive strength. It was found that larger prills influence the pressing density by creating larger defects within the microstructure of a pressed article, resulting in a decrease in compressive strength.

direct ink write↗
DOE OSTI2024

Ink Casting and 3D‐Extrusion Printing of Yb 14 MnSb 11 for High‐Temperature Thermoelectric Material

Abstract Complex shapes are created from Yb 14 MnSb 11 , a high‐temperature thermoelectric Zintl phase, via a two‐step process: i) layer‐by‐layer 3D‐extrusion of ink containing partially‐reacted powders which are ball‐milled from a blend of Yb, MnSb, and Sb powders; ii) heat treatment to synthesize the ternary compound Yb 14 MnSb 11 and densify the extruded powders. A high phase purity for Yb 14 MnSb 11 (83–94%) is achieved in both cast and 3D‐extruded ink specimens via a solid‐state reaction between Yb, MnSb, and Yb 4 Sb 3 during reactive sintering. Pressure‐free sintering at temperatures of 1200–1400 °C densifies the powders to 82% relative density but can also induce the decomposition of the Yb 14 MnSb 11 phase due to Yb sublimation. A process window with optimized sintering temperature and time is identified, achieving both low porosity and high phase purity and reaching a maximum zT = 0.61 at 1000 °C, about half of the maximum zT value for bulk Yb 14 MnSb 11 made via conventional processes (pressure sintering of precursor powders). The present approach – direct ink writing of ball‐milled powders, combined with reactive sintering – is a scalable and affordable method to fabricate thermoelectric legs with intricate 3D shapes, for enhanced performances in high‐temperature thermoelectric applications.

Chen, Ming [Department of Materials Science &amp, ↗
DOE OSTI2025

Shear Assisted Processing and Extrusion of Magnesium Alloy Machining Chips

The Pacific Northwest National Laboratory (PNNL) utilized Shear Assisted Processing and Extrusion (ShAPE) to convert magnesium alloy machining chips directly into wrought material. PNNL fabricated 0.25” and 0.50” round rod from cold compacted briquettes pressed from dry-machined chips by Loukus Technologies. The alloy composition is proprietary and protected by a Materials Transfer Agreement (MTA) between PNNL and Loukus. Extrusions were fabricated using the ShAPE 2.0 machine, tooling, and process. PNNL is evaluating tensile properties per ASTM E8 and microstructure for grain size, texture, and porosity using Scanning Electron Microscopy (SEM) and Electron Backscatter Diffraction (EBSD). Tensile properties and microstructure results were not available at the time of writing this document. Extruded rods have also been sent to Loukus for evaluation.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Synergistic torrefaction of plastic polymers and biomass

This study explores the synergistic torrefaction of biomass and plastics, aimed at enhancing bioenergy production and promoting a circular economy. By leveraging the unique properties of both materials, we investigated the thermochemical transformations occurring during the torrefaction process, from material preparation to the final characteristics of the torrefied product. The biomass used included corn stover (CS) and loblolly pine (LP), while various plastics were categorized from #1 to #7. Torrefaction was conducted at temperatures of 200, 225, and 250 °C, with subsequent extrusion of the torrefied materials and raw materials to produce composite filaments. The results show a consistent decrease in mass yield with increased torrefaction temperature, with notable variations among different biomass-plastic combinations. Co-torrefaction of biomass with polyvinyl chloride and polypropylene resulted in accelerated reaction kinetics, with an observed mass loss rate increase of 15 % at 250 °C compared to the expected rates for individual components. This synergy was quantified, indicating a 20.3 % increase in mass loss for the loblolly pine-polypropylene combination and 23.9 % for corn stover-polypropylene. In contrast, other plastics, including polyethylene terephthalate, high-density polyethylene, low-density polyethylene, polystyrene, and polycarbonate, did not exhibit significant synergistic effects. Mechanical testing indicated that the torrefaction process alters the strength and brittleness of the resulting materials, with implications for their application in bioenergy production and bio-renewable materials. Overall, this research highlights the potential of synergistic torrefaction as a viable strategy for co-processing biomass and plastics, paving the way for innovative solutions in waste management and renewable energy resource development.

09 - BIOMASS FUELS↗
DOE OSTI2025

Multiplexing core & sheath extrusion system development for additive manufacturing for inner-bead multi-material capability

Single-feed polymer extruders are widely used in large-format additive manufacturing (AM) systems; however, the increasing demand for multi-material functionality within a single part has driven significant innovation in this field. One approach involves robotic pick-and-place operations, while another explores mechanical switching of feed lines during extrusion. Although robotic pick-and-drop systems offer flexibility, they introduce longer layer times during material changes, which can negatively affect the structural integrity of the part. On the other hand, mechanical feed switching causes delays in material transitions, as the existing material must be flushed before the new material emerges from the nozzle. This poses particular challenges for smaller or more intricate parts. In this study we are developing a unique multiplexing extrusion system with core & sheath nozzle that combines two extruders via co-extrusion. This allows for a unique inside and outside inner-bead (i.e., within the same bead) multi-material capability. We believe that this technology will allow for combining neat and filled materials, ductile and stronger materials, and many other combinations to address the problems aforementioned above and disrupt the AM technology creating new opportunities and opening application areas.

Tekinalp, Halil [ORNL]↗
DOE OSTI2025

3D printable silicone compositions exhibiting high toughness and low durometer

3D printable silicones can be designed with varying crosslink density, network structures, and types of reinforcing additives. Within this design space, one may tailor the uncured material’s rheology and mechanical response to access a wide range of potential applications. However, printable, low modulus silicones, particularly those applicable to direct ink write, are underreported in published literature. To address the need for higher performance, low modulus silicones with demonstrated printability, a new set of ca. 20–50 Shore A hardness silicone elastomers exhibiting ca. 7 MPa ultimate tensile strength and ca. 400–1200% elongation at break is presented. Mechanical properties were analyzed, providing insight to the effects of formulation constituents on mechanical properties. Cyclic mechanical testing of the silicone formulations was also performed, and the energy loss and permanent set throughout cycling were determined. In conclusion, printed structures demonstrate the feasibility of these new silicones as durable frameworks for novel soft device applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Assessment of Benefits of Solid-State Advanced Manufacturing Processes for Nuclear Energy Products

The Advanced Materials and Manufacturing Technology (AMMT) program develops cross cutting technologies in support of a broad range of nuclear reactor technologies and maintains U.S. leadership in materials and manufacturing technologies for nuclear energy applications. This overall project provides the U.S. Department of Energy a critical feasibility study comparison of three solid-state processes to other AM processes, thereby providing the feasibility of the solid-state processes examined to manufacture 316H SS and ODS steel components: • Fused-filament fabrication (FFF): This work provides an initial evaluation of the impact of powder morphology and sizes on the FFF process, and the feasibility and adaptability for different material systems, to use FFF for ODS steels and 316 SS. • Shear-assisted processing and extrusion (ShAPE): Specifically for this portion of the project on ShAPE tube forming, the objectives will be to determine the feasibility to direct tube forming of high tensile strength steel tubing, specifically for ODS steel to determine the effect of the patented extrusion process on the dispersoids of the ODS material. Additionally, as often ODS powders are mechanically alloyed and therefore more platelike or angular, this feasibility was to explore the impact on the optimization process and initial feasibility of direct tube forming. • Cold spray and friction stir additive manufacturing as a stretch goal: Bulk and near net shape manufacturing processes for high-temperature, high-strength alloys are needed. Additionally, cold spray techniques can be applied in-situ at the operational level for repair and can provide multiple benefits to the nuclear industry. These tasks aim to provide information to show benefits of cold spray during the full life cycle, namely research and development, product manufacturing, and repair to mention a few key points.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2026

Multi-material direct ink writing and co-sintering of gadolinium oxide – zirconium oxide components

Methods for fabrication of multi-material or functionally graded ceramic composite architectures are of interest for numerous applications. However, conventional co-sintering of multi-material ceramic parts is a challenge because differences in the sintering behavior of the two materials leads to interfacial strain and, ultimately, component failure. Direct ink writing (DIW) is an extrusion-based additive manufacturing process that excels at multi-material printing because multiple extrusion nozzles can be installed on the same gantry system. Furthermore, the use of DIW as a method to fabricate multi-material ceramic green bodies offers an additional variable for controlling and potentially matching sintering kinetics in the slurry formulation used for two dissimilar feedstocks. In the work documented in this manuscript, we explored two strategies to successfully co-sinter multi-material ceramic oxides: slurry optimization to match sintering kinetics and material gradients to step from one material to another. This manuscript also quantifies the allowable mismatch that avoids part cracking in solid solution forming multi-material systems and discusses best strategies to reduce mismatch during co-sintering. Inks composed of gadolinium oxide (Gd 2 O 3 ) and zirconium oxide (ZrO 2 ), a surrogate for uranium oxide (UO 2 ), were thermally matched, which resulted in a sintering mismatch reduction of over 10%. It was found that ~1% mismatch is tolerable during debind cycles and that ~5% mismatch is manageable during sintering cycles after slurry formulations are optimized to match the sintering behavior. Use of continuous gradients is shown to reduce sintering mismatch, although geometric resolution may be lost due to solid solution formation.

Snarr, Patrick L. [Oak Ridge National Laboratory (↗
DOE OSTI2025

Fused filament fabrication of thermoplastic polyurethane composites with microencapsulated phase-change material

Here, the present study examines the thermal energy storage (TES) effectiveness and printability of microencapsulated phase-change material (MEPCM) combined with thermoplastic polyurethane (TPU) for fused filament fabrication (FFF). Two formulations were assessed: 24D MEPCM, which changes phase at 24 ° C, compounded with TPU pellets and 43D MEPCM, which changes phase at 43 ° C, integrated with TPU powder. These combinations are designed to evaluate the effectiveness of the form of the TPU (pellets versus powder) in the FFF process. The investigation includes a comprehensive analysis of thermal characteristics, encompassing phase-change temperature, latent heat of fusion, thermal conductivity, and thermal decomposition, which are assessed through differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). Additionally, mechanical properties, including stress-strain behavior, are examined to evaluate material suitability for TES applications, while microstructural visualization is used to provide deeper insights into material performance, structural integrity, and the quality of printed components. The 24D MEPCM and TPU pellets formulation experienced a significant loss of approximately 39.6% of PCM during filament extrusion and printing, resulting in a reduced effective latent heat. Therefore, further characterization of the pellet formulation was discontinued due to excessive leakage. In contrast, the 43D MEPCM and TPU powder formulation demonstrated minimal PCM loss, with the 60 wt.% composition achieving an effective latent heat of 132 J/g. This value represents the highest effective latent heat currently documented in the literature for PCM-polymer-composite materials produced using an FFF-based additive manufacturing process.

25 ENERGY STORAGE↗
DOE OSTI2026

HYBRID COMPOSITES VIA CO-EXTRUSION ADDITIVE MANUFACTURING-COMPRESSION MOLDING FOR PERFORMANCE OPTIMIZATION

The growing demand for hybrid polymer composites with multifunctional properties has led to the development of various hybridization techniques, such as multi-material compounding and controlled laminate stacking sequence. In this study, a novel hybrid manufacturing approach was used by integrating a multiplexing extrusion system (MExS) based on additive manufacturing with subsequent compression molding process. This technique enabled the co-extrusion of different materials during the additive manufacturing process to fabricate composites with tailored performance. The developed hybrid composite featured a skin layer of glass fiberreinforced polycarbonate (PC/GF) encapsulating a carbon fiber-reinforced acrylonitrile butadiene styrene (CF/ABS) core. The structure was engineered to promote improved thermal and impact resistance at the surface, supported by a stiff core for enhanced overall mechanical integrity. Mechanical, thermal and morphological properties of the hybrid composites were investigated to understand trade-offs in performance compared to a single-material system. The results demonstrate that this approach enables the production of multifunctional composites suitable for applications such as automotive body panels and protective housings, where a balance of weight, mechanical strength, and thermal performance is essential.

Wasti, Sanjita [ORNL]↗
DOE OSTI2025

Warpage-Resistant, Under-Extrusion-Free, High-Surface-Quality Additive Manufacturing Process for Polyethylene-Based Composite Radiation Shielding Material

Polyethylene (PE) is one of the best shielding materials for primary space radiation due to its high hydrogen content. For effective secondary neutron shielding, boron-rich fillers are incorporated to enhance performance. The semicrystalline nature and high thermal expansion coefficient of PE impede its adoption for in situ additive manufacture in space via the fused deposition modeling (FDM) 3D printing. Here, we developed an optimized PE blend to mitigate the effects of under-extrusion and warpage. Guided by studies on extrusion and warpage, we developed an optimal set of printing parameters for the proposed PE blend. The optimum PE blend─both in its pure form and when doped with fillers─has been tested on different FDM printers. The printed structures exhibit high and uniform density, smooth surfaces, no warpage, and competitive mechanical properties. The FDM-printed plates demonstrate efficient shielding from thermal neutrons, predicted via modeling and confirmed experimentally using extended Q-range small-angle neutron scattering.

additive manufacturing↗
DOE OSTI2026

Quantifying market volume sensitivity to material property modifications in polyhydroxybutyrate: A parametric analysis approach

Polyhydroxybutyrate (PHB), a biodegradable biopolymer, represents a promising alternative to petroleum-based thermoplastics. However, despite consistent market growth, PHB faces persistent commercialization challenges that limit widespread adoption. Existing research has focused predominantly on optimizing PHB production processes, leaving a critical gap in understanding which material property modifications would most effectively enhance market competitiveness. This study addresses this gap by systematically analyzing the relationship between polymer material properties and market performance using U.S. market data from 2008 to 2021 for 21 thermoplastic polymers across 19 material properties. We employed principal component regression to identify property modifications that could maximize market volume while reducing CO 2 emissions. Our parametric analysis revealed that two specific material properties – Hardness Shore A and Sheet Extrusion Temperature – significantly influence PHB marketability across different price points. Market simulations demonstrated that a 10% increase in Hardness Shore A could increase PHB market volume by 431.5 million kg while reducing emissions by 188.7 kg CO 2 . A similar 10% increase to Sheet Extrusion Temperature could yield a 297.5 million kg volume increase and a 99.2 kg CO 2 reduction in emissions. Critically, this approach is agnostic to the specific methods required to achieve these property changes, instead providing material scientists with quantitative, data-driven targets for R&D prioritization. Here, this framework offers a novel methodology for evaluating biopolymer competitiveness and supporting strategic decisions to accelerate PHB market adoption and contribute to decarbonization of the plastics industry.

09 BIOMASS FUELS↗
DOE OSTI2025

Extrusion‐Based Printing of Nanostructured Fatty Acid Gels Incorporated in Hydrogels

Soft materials with unique nanostructures such as lamellar, hexagonal, and cubic morphologies can replicate complex structures that have potential in various fields, including biomedical and industrial applications. However, a key challenge in advancing the broader applications of 3D printing for these nanostructured soft materials is insufficient mechanical properties that hinder their printability and compromise structural stability in the final product. In this study, the suitability of a fatty acid‐based lamellar gel is evaluated for direct extrusion‐based 3D printing. Here, the lamellar gel with varying water content is integrated with a photocurable hydrogel to preserve the shape and stability of the final prints. Complex 2D and 3D design patterns are used to assess extrusion behavior, structural stability, and print precision under varying pressures. Small‐angle X‐ray Scattering (SAXS) measurements reveal the formation of lamellar nanostructures and confirm their retention after photocuring in various gels. Rheological analysis confirms that these gels exhibit key properties suitable for extrusion‐based 3D printing, such as shear‐thinning behavior. Additionally, tensile testing is conducted to evaluate the mechanical properties across cured print samples. This study underscores the potential of nanostructured gels as a robust and versatile platform, facilitating the development of materials engineered for various applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Direct ink writing of aqueous-based Gadolinium (III) oxide slurries

Gadolinium (III) oxide (gadolinia, Gd 2 O 3 ) has recently been identified as an intriguing material for applications in the medical, solid oxide fuel cell, and nuclear industries. This interest drives the need for developing and understanding manufacturing techniques that can produce dense Gd 2 O 3 structures. Direct ink writing (DIW), an extrusion-based additive manufacturing method, has also garnered interest because of its capability to produce dense ceramic parts with increased complexity in an economical manner. In this study, DIW was explored as a manufacturing technique for Gd 2 O 3 . Experiments were performed to develop Gd 2 O 3 bearing inks capable of being processed via DIW. Ink solids loading and sintering temperatures were varied to assess their impact on the final density and microstructure. Optimum sintering conditions are proposed and were experimentally verified at a dwell temperature of 1500°C. Gd 2 O 3 samples were successfully manufactured using DIW, achieving densities greater than 96 % of the theoretical density.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Coarse-Grained Simulations of Polyrotaxane Hydrogels under Quiescent and Shear Conditions

Cyclodextrin-based polyrotaxanes (PR) form hydrogels in water through cyclodextrin (CD) aggregation and crystallization. These networks can break under shear flows, making them versatile platforms for extrusion-based 3D printing. To optimize the material properties of 3D-printed PR gels, a microscopic understanding of the structural evolution during 3D printing is necessary. Here, we employ coarse-grained (CG) simulations to reveal the PR assembly process at the molecular level. Our simulations reproduce the experimental crystal morphologies of PR at varying concentrations and chain lengths under quiescent conditions. Using nonequilibrium simulations, we show shear flow ruptures crystalline domain connectivity in PR gels and stacks the lamellae in the gradient direction, allowing the materials to flow during 3D printing. After the cessation of flow, the anisotropic crystal alignment and absence of available dangling PR diminish the intercrystal connectivity. The printed materials are therefore mechanically weaker than the pristine hydrogels, in agreement with experimental results. Nonetheless, by relating the microscopic structural evolution with viscoelastic properties of PR gels and solutions, we elucidate how flow conditions and sample composition affect the 3D printing performance of PR hydrogels.

Smith, Cameron D. [Dartmouth College, Hanover, NH ↗
DOE OSTI2025

Friction-based recycling: an evaluation of friction extrusion for fabricating Ti-6Al-4 V wire fabricated from machining chip feedstock

Abstract Titanium and its alloys are used in aviation and automobile industries due to their remarkable strength to weight ratio, but machining loss commonly is high with ~ 80 wt% of the material being converted to scrap. Recycling post-consumer Ti scrap directly into solid bulk products is a potential solution for repurposing valuable material. Further, eliminating fresh Ti sponge during recycling might lead to lower energy and greenhouse gas emissions. In this study, a solid-phase process known as friction extrusion was utilized to recycle Ti-6Al-4 V machining chips into solid wires which could be used as feedstock in additive manufacturing. The friction consolidation technique was first used to convert chips with varying degrees of oxygen content into solid billets for its use as feedstock material in subsequent friction extrusion. The extrudates were fabricated above the beta transition temperature, which was achieved by selecting the rotation rate and feed rate, to process the billets near 1000 °C using a tungsten-lanthana extrusion die. This work presents the first occurrence of friction extruded titanium alloy wires. The effect of friction extrusion on microstructural features, tensile properties, and texture are reported. Overall, the friction extrusion method is capable of directly recycling Ti-6Al-4 V scrap into extruded wire.

Friction Extrusion↗