Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “HVOF”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

Electrochemical Behavior of HVOF-Sprayed Amorphous and Nanocrystalline Fe-Based Fe{sub 73.13}Si{sub 11.12}B{sub 10.79}Cr{sub 2.24}C{sub 2.72} Composite Coatings

The present work describes a series of new amorphous and nanocrystalline composite coatings (composition: 87.6% Fe, 6.7% Si, 2.5% B, 2.5% Cr, 0.7% C in wt.%) on a mild steel substrate made by high-velocity oxy-fuel thermal spray at different feed rates of 20, 30 and 40 g/min. The microstructure characterization using scanning electron microscopy coupled with energy-dispersive spectroscopy shows uniform and adherent coatings of different thickness depending on the feed rate. The structure of the coating is composite in nature (mixture of amorphous and nanocrystalline phases) as confirmed by the x-ray diffraction and transmission electron microscopy. The hardness of the coating is almost 6-7 times than that of the substrate. Though polarization test of the coating demonstrates corrosion resistance in 3.5% NaCl solution similar to the substrate, the difference of corrosion potentials of the coatings and the substrate is largely negative (~ more than 200 mV against saturated calomel electrode) suggesting anodic nature of the coating as compared to the substrate resulting in sacrificial effect.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Mathematical modeling of the gas and powder flow in the (HVOF) systems to optimize their coatings quality

Thermally sprayed coatings have been extensively used to enhance materials properties and provide surface protection against their working environments in a number of industrial applications. Thermal barrier coatings (TBC) are used to reduce the thermal conductivity of aerospace turbine blades and improve the turbine overall thermal efficiency. TBC allows higher gas operating temperatures and lower blade material temperatures due to the thermal insulation provided by these ceramic coatings. In the automotive industry, coatings are currently applied to a number of moving parts that are subjected to friction and wear inside the engine such as pistons, cylinder liners, valves and crankshafts to enhance their wear resistance and prolong their useful operation and lifetime.

Tawfik, Hazem H.↗

Design Optimization of Liquid Fueled High Velocity Oxy- Fuel Thermal Spraying Technique for Durable Coating for Fossil Power Systems

High-velocity oxy–fuel (HVOF) thermal spraying was developed in 1930 and has been commercially available for twenty-five years. HVOF thermal spraying has several benefits over the more conventional plasma spray technique including a faster deposition rate which leads to quicker turn-around, with more durable coatings and higher bond strength, hardness and wear resistance due to a homogeneous distribution of the sprayed particles. HVOF thermal spraying is frequently used in engineering to deposit cermets, metallic alloys, composites and polymers, to enhance product life and performance. HVOF thermal spraying system is a highly promising technique for applying durable coatings on structural materials for corrosive and high temperature environments in advanced ultra-supercritical coal- fired (AUSC) boilers, steam turbines and gas turbines. HVOF thermal spraying is the preferred method for producing coatings with low porosity and high adhesion. HVOF thermal spray process has been shown to be one of the most efficient techniques to deposit high performance coatings at moderate cost. Variables affecting the deposit formation and coating properties include hardware characteristics such as nozzle geometry and spraying distance and process parameters such as equivalence ratio, gas flow density, and powder feedstock. In the spray process, the powder particles experience very high speeds combined with fast heating to the powder material melting point or above. This high temperature causes evaporation of the powder, dissolution, and phase transformations. Due to the complex nature of the HVOF technique, the control and optimization of the process is difficult. In general, good coating quality with suitable properties and required performance for specific applications is the goal in producing thermal spray coatings. In order to reach this goal, a deeper understanding of the spray process as a whole is needed. Although many researchers studied commercial HVOF thermal spray systems, there exists a lack of fundamental understanding of the effect of hardware characteristics and operating parameters on HVOF thermally sprayed coatings. Motivated by these issues, this study is devoted to investigate the effect of hardware characteristics (e.g. spraying distance) and operating parameters (e.g. combustion chamber pressure, equivalence ratio, and total gas flow rate) on HVOF sprayed coatings using Inconel 718 alloy. The current study provides extensive understanding of several key operating and process parameters to optimize the next generation of HVOF thermally sprayed coatings for high temperature and harsh environment applications. A facility was developed to support this endeavor in a safe and efficient way, including a HVOF thermal spray system with a Data Acquisition and Remote Controls system (DARCS). The coatings microstructure and morphology were examined using X-Ray Diffraction (XRD), Scanning Electron Microscope (SEM) and Nanoindentation.

20 FOSSIL-FUELED POWER PLANTS↗

High Velocity Oxygen Fuel Spraying of Erosion and Wear Resistant Coatings on Jet Engine Parts

High velocity oxygen fuel (HVOF) spraying is the most recent development in the field of thermal spraying. The importance of this technique for the repair and new part manufacturing of jet engine parts is rapidly increasing. The HVOF uses a supersonic oxygen-fuel flame to heat and accelerate the powder particles that form the coating. The high particle velocity results in a high density and a low porosity, a high bond strength, and a high macro and micro hardness of the coating. The high quality of the HVOF coatings makes it possible to use these coatings on high loaded, rotating parts in jet engines. This paper will highlight the use of HVOF processes to apply erosion resistant cermet coatings to high pressure compressor blades. These blades are exposed to severe erosion. Next to the D-gun process, HVOF spraying is the only nonproprietary technique that can be used to apply these high performance coatings. Also the use of the HVOF process to apply wear resistant coatings and superalloys to jet engine parts will be discussed. The difference between HVOF coatings and plasma sprayed coatings will be highlighted. During HVOF spraying, the parts are exposed to a high heat flow. Solutions to avoid overheating, especially of titanium parts, will be presented.

A T J Verbeek↗

Characterization of the Benefit of APS Flash Coatings in Improving TBC Lifetime

The addition of an air plasma sprayed (APS) “flash” layer on top of a high velocity oxygen fuel (HVOF) bond coating has been shown to extend the lifetime of thermal barrier coatings. A series of furnace cycle tests (FCTs) has been conducted at 1100 °C in air + 10% H 2 O to study the benefit of flash coatings on rod and disk alloy 247 specimens and provide a better mechanistic understanding of their benefit. Flash coatings of NiCoCrAlY and NiCoCrAlYHfSi both improved the FCT lifetime of rod specimens tested in 100-h cycles and disk specimens tested in 1-h cycles. In 1-h cycles, the NiCoCrAlY flash coating significantly outperformed an HVOF-only NiCoCrAlYHfSi bond coating and a NiCoCrAlYHfSi flash coating. Both flash coatings increased the bond coating roughness compared to HVOF. During exposure, the flash layer formed an intermixed alumina-metal layer that appeared to inhibit crack formation. Using a time series of observations, the lower Y + Hf content in the Y-only flash coating appeared to reduce Al consumption. The HVOF layer acted as a source of Al for the adjacent mixed zone. A second series of specimens included a fully APS bond coating where oxide had penetrated through the entire coating to the substrate after only 100, 1-h cycles and lifetime was similar to an HVOF-only bond coating. The inner HVOF layer with the outer APS flash coating prevented this complete penetration from occurring.

Pint, Bruce↗

Microstructure, Processing, Performance Relationships for High Temperature Coatings

HVOF coating have shown high resistance to corrosion in fossil energy applications and it is generally accepted that mechanical failure, e.g. cracking or spalling, ultimately will determine coating lifetime. The high velocity oxygen-fuel method (HVOF) of applying coatings is one of the most commercially viable and allows the control of various parameters including powder particle velocity and temperature which influence coating properties, such as residual stress, bond coat strength and microstructure. Methods of assessing the mechanical durability of coatings are being developed in order to explore the relationship between HVOF spraying parameters and the mechanical properties of the coating and coating bond strength. The room temperature mechanical strength, as well as the resistance of the coating to cracking/spalling during thermal transients, is of considerable importance. Eddy current, acoustic emission and thermal imaging methods are being developed to detect coating failure during thermal cycling tests and room temperature tensile tests. Preliminary results on coating failure of HVOF FeAl coatings on carbon steel, as detected by eddy current measurements during thermal cycling, are presented. The influence of HVOF coating parameters of iron aluminides - applied to more relevant structural steels, like 316 SS and Grade 91 steel, - on coating durability will be explored once reliable methods for identification of coating failure have been developed.

20 FOSSIL-FUELED POWER PLANTS↗

The Effect of Coating Composition and Geometry on Thermal Barrier Coatings Lifetime

Several factors are being investigated that affect the performance of thermal barrier coatings (TBC) for use in land-based gas turbines where coatings are mainly thermally sprayed. This study examined high velocity oxygen fuel (HVOF), air plasma-sprayed (APS), and vacuum plasma-sprayed (VPS) MCrAlYHfSi bond coatings with APS YSZ top coatings at 900–1100 °C. For superalloy 247 substrates and VPS coatings tested in 1 h cycles at 1100 °C, removing 0.6 wt %Si had no effect on average lifetime in 1 h cycles at 1100 °C, but adding 0.3%Ti had a negative effect. Rod specimens were coated with APS, HVOF, and HVOF with an outer APS layer bond coating and tested in 100 h cycles in air + 10%H 2 O at 1100 °C. With an HVOF bond coating, initial results indicate that 12.5 mm diameter rod specimens have much shorter 100 h cycle lifetimes than disk specimens. Furthermore, much longer lifetimes were obtained when the bond coating had an inner HVOF layer and outer APS layer.

36 MATERIALS SCIENCE↗

Microstructure, Processing, Performance Relationships for High Temperature Coatings

HVOF coatings have shown high resistance to corrosion in fossil energy applications and it is generally accepted that mechanical failure, e.g. cracking or spalling, ultimately will determine coating lifetime. The high velocity oxygen-fuel method (HVOF) for applying coatings is one of the most commercially viable and allows the control of various parameters including powder particle velocity and temperature which influence coating properties, such as residual stress, bond coat strength and microstructure. The mechanical durability of coatings is being assessed using a dual eddy current coil method to monitor crack formation in real time during thermal cycling. Absolute impedence signals from two coils, which interrogate two different areas on the sample, are collected. Crack detection can be determined from the differential signal generated from these absolute signals. The coils are operated at two different frequencies, resulting in two differential signals used for crack detection. Currently this crack detection method is being used to elucidate the influence of thermal cycling temperature and coating thickness on cracking. Recent results (cycles to failure) will be presented for FeAl coatings thermally sprayed (HVOF) onto carbon steel to two coating thicknesses (160 microns and 250 microns thick) and subsequently cycled at temperatures up to 700oC. Thinner coatings exhibit greater resistance to cracking. Ultimately the resistance to cracking will be used to explore the relationship between HVOF spraying parameters, the mechanical properties of the coating and coating bond strength to develop optimized thermal spray parameters. To this end thermal spray coatings (FeAl and Fe3Al) have been applied to additional alloy substrates (Grade 91 steel, 316 SS, etc.) relevant to the fossil industry. Future plans also include a direct comparison to conventional weld overlay coatings currently used in the industry as well as exploration of new coatings. The room temperature mechanical strength and coating adhesion to the substrate is also of considerable importance. Eddy current methods are being developed to detect coating failure during room temperature tensile tests to optimize surface preparation as well as aid in the optimization of the HVOF thermal spray parameters.

20 FOSSIL-FUELED POWER PLANTS↗

Effect of Air Plasma Sprayed Flash Bond Coatings on Furnace Cycle Lifetime of Disks and Rods

Air plasma sprayed (APS) flash coatings on high velocity oxygen fuel (HVOF) bond coatings are well known to extend the lifetime of thermal barrier coatings (TBCs). Recent work compared flash coatings of NiCoCrAlY and NiCoCrAlYHfSi applied to both rods and disk substrates of alloy 247. For rod specimens, 100 h cycles were used at 1100 °C in wet air. Both flash coatings significantly improved the lifetime compared to HVOF-only and vacuum plasma spray (VPS)-only MCrAlY bond coatings with no statistical difference between the two flash coatings. For disk specimens tested in 1 h cycles at 1100 °C in wet air, the NiCoCrAlY flash coating significantly outperformed an HVOF-only NiCoCrAlYHfSi bond coating and a NiCoCrAlYHfSi flash coating. The flash coatings formed a mixed oxide-metal zone that appeared to inhibit crack formation and therefore extend lifetime. In addition to the flash coating increasing the bond coating roughness, the underlying HVOF layer acted as a source of Al for this intermixed zone and prevented the oxide from penetrating deeper into the bond coating. Here, the lower Y+Hf content in the Y-only flash coating appeared to minimize oxidation in the flash layer, thereby increasing the benefit compared to a NiCoCrAlYHfSi flash coating.

42 ENGINEERING↗

Microstructure, Processing, Performance Relationships for High Temperature Coatings

This work evaluates the suitability of iron aluminide coatings for use in high temperature fossil fuel combustion environments, such as boiler applications. The coatings are applied using High Velocity Oxy-Fuel (HVOF) thermal spray techniques. Iron aluminide coatings, with the nominal composition of Fe3Al, were applied to various high temperature structural materials (316 Stainless Steel, 9Cr-1Mo steel and Inconel 600) that typically lack inherent resistance to environmental degradation found in fossil fuel combustion atmospheres. Coating/substrate combinations were subjected to thermal cycling to evaluate the effect of HVOF parameters, coating thickness, substrate material and substrate surface roughness on the resistance to coating delamination and cracking. It was found that substrate surface roughness had a profound influence on the performance of a given substrate/coating system and that surface preparation techniques will need to be tailored to the specific substrate material. Also, higher particle velocity during HVOF thermal spray deposition of the iron aluminide coatings tended to result in better-performing coating/substrate systems with less delamination at the coating/substrate interface. Some combinations of HVOF parameters, coating thickness and substrate materials were found to perform extremely well even at temperatures up to 900oC. However, in some cases, substantial reactions at the interface were observed.

20 FOSSIL-FUELED POWER PLANTS↗

Effect of APS flash bond coatings and curvature on TBC performance on rod specimens

The addition of an air plasma sprayed (APS) “flash” bond coating layer on top of a high velocity oxy-fuel (HVOF) bond coating greatly extended the lifetime of APS yttria stabilized zirconia (YSZ) thermal barrier coatings (TBC) on rod specimens of superalloy 247 tested using 100-h cycles in air+10%H 2 O at 1100 °C. The flash bond coatings of both NiCoCrAlY and NiCoCrAlYHfSi powder were compared to an HVOF-only and a vacuum plasma sprayed (VPS) NiCoCrAlYHfSi bond coating. Here, the flash coatings appear to form a mixed oxide-metal zone, which likely inhibits crack formation and therefore extends lifetime compared to conventional bond coatings. The underlying dense HVOF layer appeared to act as a source of Al for this intermixed zone and prevented the oxide from penetrating deeper into the bond coating. Residual stress in the thermally-grown Al 2 O 3 scale was measured using photo-luminescence piezospectroscopy (PLPS) as a function of time for each coating variation, including a comparison of concave and convex surfaces on a specially designed rod.

36 MATERIALS SCIENCE↗

Effect of APS flash bond coatings on furnace cycle lifetime of disks and rods

Air plasma sprayed (APS) flash coatings on high velocity oxygen fuel (HVOF) bond coatings are well known to extend the lifetime of thermal barrier coatings. Recent work compared flash coatings of NiCoCrAlY and NiCoCrAlYHfSi applied to both rods and disk substrates of alloy 247. For rod specimens, 100-h cycles were used at 1100°C in wet air. Both flash coatings significantly improved the lifetime compared to HVOF-only and VPS-only MCrAlY bond coatings with no statistical difference between the two flash coatings. For disk specimens tested in 1-h cycles at 1100°C in wet air, the NiCoCrAlY flash coating significantly outperformed an HVOFonly NiCoCrAlYHfSi bond coating and a NiCoCrAlYHfSi flash coating. The flash coatings formed a mixed oxide-metal zone that appeared to inhibit crack formation and extend lifetime. In addition to the flash coating increasing the bond coating roughness, the underlying HVOF layer acted as a source of Al for this intermixed zone and prevented the oxide from penetrating deeper into the bond coating. The lower Y+Hf level in the Y-only flash coating appeared to minimize oxidation in the flash layer, thereby increasing the benefit compared to a NiCoCrAlYHfSi flash coating.

Pint, Bruce↗

Advanced thermal barrier coatings for operation in high hydrogen content fueled gas turbines

The Center for Thermal Spray Research (CTSR) at Stony Brook University in partnership with its industrial Consortium for Thermal Spray Technology is investigating science and technology related to advanced metallic alloy bond coats and ceramic thermal barrier coatings for applications in the hot section of gasified coal-based high hydrogen turbine power systems. In conjunction with our OEM partners (GE and Siemens) and through strategic partnership with Oak Ridge National Laboratory (ORNL) (materials degradation group and high temperature materials laboratory), a systems approach, considering all components of the TBC (multilayer ceramic top coat, metallic bond coat & superalloy substrate) is being taken during multi-layered coating design, process development and subsequent environmental testing. Recent advances in process science and advanced in situ thermal spray coating property measurement enabled within CTSR has been incorporated for full-field enhancement of coating and process reliability. The development of bond coat processing during this program explored various aspects of processing and microstructure and linked them to performance. The determination of the bond coat material was carried out during the initial stages of the program. Based on tests conducted both at Stony Brook University as well as those carried out at ORNL it was determined that the NiCoCrAlYHfSi (Amdry) bond coats had considerable benefits over NiCoCrAlY bond coats. Since the studies were also conducted at different cycling frequencies, thereby addressing an associated need for performance under different loading conditions, the Amdry bond coat was selected as the material of choice going forward in the program. With initial investigations focused on the fabrication of HVOF bond coats and the performance of TBC under furnace cycle tests , several processing strategies were developed. Two-layered HVOF bond coats were developed to render optimal balance of density and surface roughness and resulted in improved TBC lifetimes. Processing based approaches of identifying optimal processing regimes deploying advanced in-situ coating property measurements and in-flight diagnostic tools were used to develop process maps for bond coats. Having established a framework for the bond coat processing using the HVOF process, effort were channeled towards fabrication of APS and VPS bond coats with the same material composition. Comparative evaluation of the three deposition processes with regard to their microstrcuture , surface profiles and TBC performance were carried out and provided valuable insights into factors that require concurrent consideration for the development of bond coats for advanced TBC systems. Over the course of this program several advancements were made on the development of durable thermal barrier coatings. Process optimization techniques were utilized to identify processing regimes for both conventional YSZ as well as other TBC compositions such as Gadolinium Zirconate and other Co-doped materials. Measurement of critical properties for these formed the initial stages of the program to identify potential challenges in their implementation as part of a TBC system. High temperature thermal conductivity measurements as well as sintering behavior of both YSZ and GDZ coatings were evaluated as part of initial efforts to undersand the influence of processing on coating properties. By effectively linking fundamental coating properties of fracture toughness and elastic modulus to the cyclic performance of coatings, a durability strategy for APS YSZ coatings was developed. In order to meet the goals of fabricating a multimaterial TBC system further research was carried out on the development of a gradient thermal conductivity model and the evaluation of sintering behavior of multimaterial coatings. Layer optimization for desired properties in the multimaterial TBC was achieved by an iterative feedback approach utilizing process maps and in-situ and ex-situ coating property sensors. Addressing the challenges pertaining to the integration of the two materials YSZ and GDZ led to one of most the critical outcomes of this program, the development of durable multimaterial, multifunctional TBC systems.

36 MATERIALS SCIENCE↗

Optimal Substrate Preheating Model for Thermal Spray Deposition of Thermosets onto Polymer Matrix Composites

High velocity oxy-fuel (HVOF) sprayed, functionally graded polyimide/WC-Co composite coatings on polymer matrix composites (PMC's) are being investigated for applications in turbine engine technologies. This requires that the polyimide, used as the matrix material, be fully crosslinked during deposition in order to maximize its engineering properties. The rapid heating and cooling nature of the HVOF spray process and the high heat flux through the coating into the substrate typically do not allow sufficient time at temperature for curing of the thermoset. It was hypothesized that external substrate preheating might enhance the deposition behavior and curing reaction during the thermal spraying of polyimide thermosets. A simple analytical process model for the deposition of thermosetting polyimide onto polymer matrix composites by HVOF thermal spray technology has been developed. The model incorporates various heat transfer mechanisms and enables surface temperature profiles of the coating to be simulated, primarily as a function of substrate preheating temperature. Four cases were modeled: (i) no substrate preheating; (ii) substrates electrically preheated from the rear; (iii) substrates preheated by hot air from the front face; and (iv) substrates electrically preheated from the rear and by hot air from the front.

Ivosevic, M.↗

Crack Detection in High-Velocity Oxygen-Fuel-Sprayed Al{sub 59.2}Cu{sub 25.5}Fe{sub 12.3}B{sub 3} Quasicrystalline Coatings Using Piezoelectric Active Sensors

Quasicrystals have received some attention in recent years regarding their potential usefulness as low friction and wear resistant materials. When quasicrystalline (QC) coatings are exposed to different levels of external loading or are subjected to thermal stresses, crack nucleation, and propagation become life-limiting factors. In this investigation, Al{sub 59.2}Cu{sub 25.5}Fe{sub 12.3}B{sub 3} QC coatings were deposited onto AISI-A36 steel substrates using the high-velocity oxygen-fuel (HVOF) technique. The coatings were deposited at different oxygen-to-fuel ratios. To characterize the integrity of the coatings, the active piezoceramic excitation technique was applied to detect the propagation of cracks during three-point bending tests. The piezoelectric transducer signal was processed using wavelet transformation analysis. The results revealed that the coated samples displayed different densities of cracks depending on the oxygen-to-fuel. The crack density was found higher for coatings formed using a slightly oxidizing flame. The opening of the pre-existing cracks in the coating was the main reason of signal attenuation during piezoelectric excitation. The HVOF-sprayed AlCuFeB quasicrystalline coating, with thickness between 150 and 180 μm, withstands a flexural stress as high as 340 MPa. To the best of our knowledge, this study is the first that provides a quantitative assessment of the viability of QC coatings in mechanical applications in spite of their intrinsic brittleness.

36 MATERIALS SCIENCE↗