Results for “HECC” — Page 2

NASA NTRS2018

Evaluating the Suitability of Commercial Clouds for NASA's High Performance Computing Applications: A Trade Study

NASA’s High-End Computing Capability (HECC) Project is periodically asked if it could be more cost effective through the use of commercial cloud resources. To answer the question, HECC’s Application Performance and Productivity (APP) team undertook a performance and cost evaluation comparing three domains: two commercial cloud providers, Amazon and Penguin, and HECC’s in-house resources—the Pleiades and Electra systems. In the study, the APP team used a combination of the NAS Parallel Benchmarks (NPB) and six full applications from NASA’s workload on Pleiades and Electra to compare performance of nodes based on three different generations of Intel Xeon processors—Haswell, Broadwell, and Skylake. Because of export control limitations, the most heavily used applications on Pleiades and Electra could not be used in the cloud; therefore, only one of the applications, OpenFOAM, represents work from the Aeronautics Research Mission Directorate and the Human and Exploration Mission Directorate. The other five applications are from the Science Mission Directorate.

High Performance↗

NASA NTRSDate not supplied

NASA Small Engine Components Compressor Test Facility: High Efficiency Centrifugal Compressor Vaneless Diffuser and Transition Duct Configurations

The original vaned configuration of the High Efficiency Centrifugal Compressor (HECC) was developed with aggressive design targets to facilitate advancement of state-of-the-art technology in gas turbine compressors. This work documents modifications to the Small Engine Components Compressor Test Facility to support testing of the HECC vaneless diffuser and transition duct configurations, both of which are open geometries. These configurations were developed as follow-up studies to improve understanding of the differences between the predicted and actual performance of the original HECC vaned diffuser stage. Specifically, the vaneless diffuser was designed to provide the impeller with ideal exit conditions such that the impeller performance could be isolated from downstream stationary components, and the additively manufactured transition duct inlet configuration enables investigation into the effects of the inlet flow path on the stage performance. Features of note in the facility are active clearance control, bleed flow regulation, modular inlet configurations, and steady-state and fast-response instrumentation throughout the flow path. Details of the facility and instrumentation are presented as well as the baseline performance of the compressor stage. The geometry, performance, and detailed aerodynamic data have been made available to the public at https://storage.googleapis.com/heccdata/NASA-HECC-Data-Archive.zip.

centrifugal compressor↗

NASA NTRSDate not supplied

NASA Small Engine Components Compressor Test Facility: High Efficiency Centrifugal Compressor Vaneless Diffuser and Transition Duct Configurations

The original vaned configuration of the High Efficiency Centrifugal Compressor (HECC) was developed with aggressive design targets to facilitate advancement of state-of-the-art technology in gas turbine compressors. This work documents modifications to the Small Engine Components Compressor Test Facility to support testing of the HECC vaneless diffuser and transition duct configurations, both of which are open geometries. These configurations were developed as follow-up studies to improve understanding of the differences between the predicted and actual performance of the original HECC vaned diffuser stage. Specifically, the vaneless diffuser was designed to provide the impeller with ideal exit conditions such that the impeller performance could be isolated from downstream stationary components, and the additively manufactured transition duct inlet configuration enables investigation into the effects of the inlet flow path on the stage performance. Features of note in the facility are active clearance control, bleed flow regulation, modular inlet configurations, and steady-state and fast-response instrumentation throughout the flow path. Details of the facility and instrumentation are presented as well as the baseline performance of the compressor stage. The geometry, performance, and detailed aerodynamic data have been made available to the public at https://storage.googleapis.com/hecc-data/NASA-HECC-Data-Archive.zip.

centrifugal compressor↗

NASA NTRSDate not supplied

GT2024-139262: Development of a Computational Fluid Dynamics Model for a High-Speed Centrifugal Compressor

Computational fluid dynamics (CFD) has become widely used in the design and analysis of turbomachinery components such as centrifugal compressors. However, CFD is only a limited representation of experimental cases and struggles to model complex flows or lack model details to increase computation speed. The High Efficiency Centrifugal Compressor (HECC) was designed by United Technologies Research Center for NASA to investigate the difficulties behind improving centrifugal compressor technology and to provide an open case to the turbomachinery research community. The CFD technology seen in previous numerical models of the compressor have improved since then. In this study, a high-fidelity computational model for the vaneless configuration of HECC operating at its design point was developed and compared to an equivalent experimental case. This model incorporated GPU versions of mesh generation code WAND and solver code LEO from AeroDynamic Solutions, Inc. Blade sections extracted from the solid model formed the basis of the impeller mesh, while the remainder of the stage was modeled as ducts. Standard day aerodynamic conditions, design rotational speed, design mass flow rate, and inlet flow angles served as additional inputs. A mesh sensitivity study was performed prior to using the model for analysis. The accuracy of the model’s predictions of impeller and stage performance were assessed by comparing the total pressure ratio, total temperature rise ratio, and adiabatic efficiency to the corresponding parameters observed in the experimental case. Results showed a general overprediction of compressor performance by the model. Predictions were more accurate for the impeller performance compared to those for the full compressor stage. Spanwise analyses showed that the model tended to follow flow behavior patterns exhibited in the experiment. Beyond this study, this model was used to examine HECC aerodynamics and performance in research following thereafter.

centrifugal compressor↗

NASA NTRS2020

NASA GPU Hackathon Yields Significant Code Improvements

The NASA GPU Hackathon 2020 brought together application developers and computer experts to help get important NASA applications running effectively on graphics processing unit (GPU) nodes. Nine teams of application developers participated in this virtual event, a major impetus for teams to modernize codes of interest for NASA missions to CPU nodes containing GPU accelerators, with a focus on hands-on problem solving. The photo in Figure1 shows 30 of the more than50 participants. The HECC project and NVIDIA jointly organized the event, and HECC provided five Pleiades nodes each with 4 V100 GPUs for teams to use. The virtual event, which took place over four days from September 28–October 7, 2020, used Microsoft Teams and Slack as collaboration tools. Each team consisted of three to six members from NASA Centers and supporting organizations. The teams were paired with one to two mentors from industry, government, and academia. The experience levels of the teams ranged from being GPU novices to advanced CUDA programming experts. OpenACC and the emerging Kokkos API were used in addition to CUDA for GPU programming. During the event, which focused on accelerating AeroSciences and CFD applications, most teams achieved considerable performance improvements on both GPUs and CPUs. For example, a team with no GPU experience completed a first port of a time-critical loop to a GPU. Another team of expert CUDA programmers were able to restructure their algorithm, yielding a factor of five speed-up. And another team sped up some of their CUDA kernels by a factor of 20, which directly translated into their production code. This article highlights some of the many successes resulting from the event.

HECC↗

NASA NTRS2017

Progress of High Efficiency Centrifugal Compressor Simulations Using TURBO

Three-dimensional, time-accurate, and phase-lagged computational fluid dynamics (CFD) simulations of the High Efficiency Centrifugal Compressor (HECC) stage were generated using the TURBO solver. Changes to the TURBO Parallel Version 4 source code were made in order to properly model the no-slip boundary condition along the spinning hub region for centrifugal impellers. A startup procedure was developed to generate a converged flow field in TURBO. This procedure initialized computations on a coarsened mesh generated by the Turbomachinery Gridding System (TGS) and relied on a method of systematically increasing wheel speed and backpressure. Baseline design-speed TURBO results generally overpredicted total pressure ratio, adiabatic efficiency, and the choking flow rate of the HECC stage as compared with the design-intent CFD results of Code Leo. Including diffuser fillet geometry in the TURBO computation resulted in a 0.6 percent reduction in the choking flow rate and led to a better match with design-intent CFD. Diffuser fillets reduced annulus cross-sectional area but also reduced corner separation, and thus blockage, in the diffuser passage. It was found that the TURBO computations are somewhat insensitive to inlet total pressure changing from the TURBO default inlet pressure of 14.7 pounds per square inch (101.35 kilopascals) down to 11.0 pounds per square inch (75.83 kilopascals), the inlet pressure of the component test. Off-design tip clearance was modeled in TURBO in two computations: one in which the blade tip geometry was trimmed by 12 mils (0.3048 millimeters), and another in which the hub flow path was moved to reflect a 12-mil axial shift in the impeller hub, creating a step at the hub. The one-dimensional results of these two computations indicate non-negligible differences between the two modeling approaches.

turbomachinery↗

NASA NTRSDate not supplied

Updates in Developing a Prototype Science Pipeline and Full-Volume, Global Hyperspectral Synthetic Data Sets for NASA’s Earth System Observatory’s Upcoming Surface, Biology and Geology Mission

The Surface Biology and Geology (SBG) mission recently passed mission confirmation review and has entered phase A – design and development. SBG will acquire high resolution solar-reflected spectroscopy and thermal infrared observations at a data rate of ~2.5 TB/day and generate products at ~40 TB/day. Given that the per-day volume is greater than NASA’s total extant airborne hyperspectral data collection, collecting, processing, disseminating, and exploiting the SBG data present new challenges. To meet these challenges, we have developed a prototype science pipeline and a full-volume global hyperspectral synthetic data set to help prepare for SBG’s flight (see poster GC42D-0730). Our science pipeline is based on the science processing technology developed for NASA’s Kepler and TESS planet-hunting missions. The pipeline infrastructure, Ziggy, provides a scalable architecture for robust, repeatable, and replicable science and application products that can be run on a range of systems from a laptop to the cloud or a supercomputer. Ziggy is compliant with NASA Procedural Requirement (NPR) 7150.2C, is at a technical readiness level (TRL) of 7 and has been released to github.com/nasa/ziggy. We integrated Ziggy with EO-1/Hyperion workflows to build a prototype pipeline and ingested the 17-year mission archive that provides globally sampled visible through shortwave infrared spectra that are representative of SBG data types and volumes. We fully implemented the first stage and processed the entire 55 TB Hyperion data set from the raw data (Level 0) to top-of-the-atmosphere radiance (Level 1R). We are currently evaluating the ISOFIT atmospheric correction module to convert the L1R data to surface reflectance (Level 2) before reprocessing the full data set to L2. Crosschecks are being performed with RadCalNet as well as with coincident observations by AVIRIS. We are also investigating modern methods for georectifying the Hyperion scenes. Finally, we describe an analysis of the cost to conduct forward processing and reprocessing campaigns for SBG on HECC with dedicated compute and storage resources using the resurrected Hyperion pipeline as a proxy for full-volume SBG data. The analysis demonstrates that SBG L0 data can be processed to L2 on HECC with full reprocessing campaigns every two years for ~$2.6M over a 7-year lifespan. Moreover, 69% of the system capacity would be available for other activities, possibly enabling future open-source science activities, including algorithm development, L3+ processing, .etc.

ESD↗

NASA NTRS2014

High Efficiency Centrifugal Compressor for Rotorcraft Applications

The report "High Efficiency Centrifugal Compressor for Rotorcraft Applications" documents the work conducted at UTRC under the NRA Contract NNC08CB03C, with cost share 2/3 NASA, and 1/3 UTRC, that has been extended to 4.5 years. The purpose of this effort was to identify key technical barriers to advancing the state-of-the-art of small centrifugal compressor stages; to delineate the measurements required to provide insight into the flow physics of the technical barriers; to design, fabricate, install, and test a state-of-the-art research compressor that is representative of the rear stage of an axial-centrifugal aero-engine; and to acquire detailed aerodynamic performance and research quality data to clarify flow physics and to establish detailed data sets for future application. The design activity centered on meeting the goal set outlined in the NASA solicitation-the design target was to increase efficiency at higher work factor, while also reducing the maximum diameter of the stage. To fit within the existing Small Engine Components Test Facility at NASA Glenn Research Center (GRC) and to facilitate component re-use, certain key design parameters were fixed by UTRC, including impeller tip diameter, impeller rotational speed, and impeller inlet hub and shroud radii. This report describes the design effort of the High Efficiency Centrifugal Compressor stage (HECC) and delineation of measurements, fabrication of the compressor, and the initial tests that were performed. A new High-Efficiency Centrifugal Compressor stage with a very challenging reduction in radius ratio was successfully designed, fabricated and installed at GRC. The testing was successful, with no mechanical problems and the running clearances were achieved without impeller rubs. Overall, measured pressure ratio of 4.68, work factor of 0.81, and at design exit corrected flow rate of 3 lbm/s met the target requirements. Polytropic efficiency of 85.5 percent and stall margin of 7.5 percent were measured at design flow rate and speed. The measured efficiency and stall margin were lower than pre-test CFD predictions by 2.4 percentage points (pt) and 4.5 pt, respectively. Initial impressions from the experimental data indicated that the loss in the efficiency and stall margin can be attributed to a design shortfall in the impeller. However, detailed investigation of experimental data and post-test CFD simulations of higher fidelity than pre-test CFD, and in particular the unsteady CFD simulations and the assessment with a wider range of turbulence models, have indicated that the loss in efficiency is most likely due to the impact of unfavorable unsteady impeller/diffuser interactions induced by diffuser vanes, an impeller/diffuser corrected flow-rate mismatch (and associated incidence levels), and, potentially, flow separation in the radial-to-axial bend. An experimental program with a vaneless diffuser is recommended to evaluate this observation. A subsequent redesign of the diffuser (and the radial-to-axial bend) is also recommended. The diffuser needs to be redesigned to eliminate the mismatching of the impeller and the diffuser, targeting a slightly higher flow capacity. Furthermore, diffuser vanes need to be adjusted to align the incidence angles, to optimize the splitter vane location (both radially and circumferentially), and to minimize the unsteady interactions with the impeller. The radial-to-axial bend needs to be redesigned to eliminate, or at least minimize, the flow separation at the inner wall, and its impact on the flow in the diffuser upstream. Lessons were also learned in terms of CFD methodology and the importance of unsteady CFD simulations for centrifugal compressors was highlighted. Inconsistencies in the implementation of a widely used two-equation turbulence model were identified and corrections are recommended. It was also observed that unsteady simulations for centrifugal compressors require significantly longer integration times than what is current practice in industry.

Gorazd Medic↗

NASA NTRS2014

High Efficiency Centrifugal Compressor for Rotorcraft Applications

The report "High Efficiency Centrifugal Compressor for Rotorcraft Applications" documents the work conducted at UTRC under the NRA Contract NNC08CB03C, with cost share 2/3 NASA, and 1/3 UTRC, that has been extended to 4.5 years. The purpose of this effort was to identify key technical barriers to advancing the state-of-the-art of small centrifugal compressor stages; to delineate the measurements required to provide insight into the flow physics of the technical barriers; to design, fabricate, install, and test a state-of-the-art research compressor that is representative of the rear stage of an axial-centrifugal aero-engine; and to acquire detailed aerodynamic performance and research quality data to clarify flow physics and to establish detailed data sets for future application. The design activity centered on meeting the goal set outlined in the NASA solicitation-the design target was to increase efficiency at higher work factor, while also reducing the maximum diameter of the stage. To fit within the existing Small Engine Components Test Facility at NASA Glenn Research Center (GRC) and to facilitate component re-use, certain key design parameters were fixed by UTRC, including impeller tip diameter, impeller rotational speed, and impeller inlet hub and shroud radii. This report describes the design effort of the High Efficiency Centrifugal Compressor stage (HECC) and delineation of measurements, fabrication of the compressor, and the initial tests that were performed. A new High-Efficiency Centrifugal Compressor stage with a very challenging reduction in radius ratio was successfully designed, fabricated and installed at GRC. The testing was successful, with no mechanical problems and the running clearances were achieved without impeller rubs. Overall, measured pressure ratio of 4.68, work factor of 0.81, and at design exit corrected flow rate of 3 lbm/s met the target requirements. Polytropic efficiency of 85.5 percent and stall margin of 7.5 percent were measured at design flow rate and speed. The measured efficiency and stall margin were lower than pre-test CFD predictions by 2.4 percentage points (pt) and 4.5 pt, respectively. Initial impressions from the experimental data indicated that the loss in the efficiency and stall margin can be attributed to a design shortfall in the impeller. However, detailed investigation of experimental data and post-test CFD simulations of higher fidelity than pre-test CFD, and in particular the unsteady CFD simulations and the assessment with a wider range of turbulence models, have indicated that the loss in efficiency is most likely due to the impact of unfavorable unsteady impeller/diffuser interactions induced by diffuser vanes, an impeller/diffuser corrected flow-rate mismatch (and associated incidence levels), and, potentially, flow separation in the radial-to-axial bend. An experimental program with a vaneless diffuser is recommended to evaluate this observation. A subsequent redesign of the diffuser (and the radial-to-axial bend) is also recommended. The diffuser needs to be redesigned to eliminate the mismatching of the impeller and the diffuser, targeting a slightly higher flow capacity. Furthermore, diffuser vanes need to be adjusted to align the incidence angles, to optimize the splitter vane location (both radially and circumferentially), and to minimize the unsteady interactions with the impeller. The radial-to-axial bend needs to be redesigned to eliminate, or at least minimize, the flow separation at the inner wall, and its impact on the flow in the diffuser upstream. Lessons were also learned in terms of CFD methodology and the importance of unsteady CFD simulations for centrifugal compressors was highlighted. Inconsistencies in the implementation of a widely used two-equation turbulence model were identified and corrections are recommended. It was also observed that unsteady simulations for centrifugal compressors require significantly longer integration times than what is current practice in industry.

Gorazd Medic↗

NASA NTRS2017

NeMO-Net: The Neural Multi-Modal Observation and Training Network for Global Coral Reef Assessment

In the past decade, coral reefs worldwide have experienced unprecedented stresses due to climate change, ocean acidification, and anthropomorphic pressures, instigating massive bleaching and die-off of these fragile and diverse ecosystems. Furthermore, remote sensing of these shallow marine habitats is hindered by ocean wave distortion, refraction and optical attenuation, leading invariably to data products that are often of low resolution and signal-to-noise (SNR) ratio. However, recent advances in UAV and Fluid Lensing technology have allowed us to capture multispectral 3D imagery of these systems at sub-cm scales from above the water surface, giving us an unprecedented view of their growth and decay. Exploiting the fine-scaled features of these datasets, machine learning methods such as MAP, PCA, and SVM can not only accurately classify the living cover and morphology of these reef systems (below 8 percent error), but are also able to map the spectral space between airborne and satellite imagery, augmenting and improving the classification accuracy of previously low-resolution datasets. We are currently implementing NeMO-Net, the first open-source deep convolutional neural network (CNN) and interactive active learning and training software to accurately assess the present and past dynamics of coral reef ecosystems through determination of percent living cover and morphology. NeMO-Net will be built upon the QGIS platform to ingest UAV, airborne and satellite datasets from various sources and sensor capabilities, and through data-fusion determine the coral reef ecosystem makeup globally at unprecedented spatial and temporal scales. To achieve this, we will exploit virtual data augmentation, the use of semi-supervised learning, and active learning through a tablet platform allowing for users to manually train uncertain or difficult to classify datasets. The project will make use of Pythons extensive libraries for machine learning, as well as extending integration to GPU and High-End Computing Capability (HECC) on the Pleiades supercomputing cluster, located at NASA Ames. The project is being supported by NASAs Earth Science Technology Office (ESTO) Advanced Information Systems Technology (AIST-16) Program.

NeMO-Net↗

NASA NTRS2017

NeMO-Net The Neural Multi-Modal Observation Training Network for Global Coral Reef Assessment

In the past decade, coral reefs worldwide have experienced unprecedented stresses due to climate change, ocean acidification, and anthropomorphic pressures, instigating massive bleaching and die-off of these fragile and diverse ecosystems. Furthermore, remote sensing of these shallow marine habitats is hindered by ocean wave distortion, refraction and optical attenuation, leading invariably to data products that are often of low resolution and signal-to-noise (SNR) ratio. However, recent advances in UAV and Fluid Lensing technology have allowed us to capture multispectral 3D imagery of these systems at sub-cm scales from above the water surface, giving us an unprecedented view of their growth and decay. Exploiting the fine-scaled features of these datasets, machine learning methods such as MAP, PCA, and SVM can not only accurately classify the living cover and morphology of these reef systems (below 8 error), but are also able to map the spectral space between airborne and satellite imagery, augmenting and improving the classification accuracy of previously low-resolution datasets.We are currently implementing NeMO-Net, the first open-source deep convolutional neural network (CNN) and interactive active learning and training software to accurately assess the present and past dynamics of coral reef ecosystems through determination of percent living cover and morphology. NeMO-Net will be built upon the QGIS platform to ingest UAV, airborne and satellite datasets from various sources and sensor capabilities, and through data-fusion determine the coral reef ecosystem makeup globally at unprecedented spatial and temporal scales. To achieve this, we will exploit virtual data augmentation, the use of semi-supervised learning, and active learning through a tablet platform allowing for users to manually train uncertain or difficult to classify datasets. The project will make use of Pythons extensive libraries for machine learning, as well as extending integration to GPU and High-End Computing Capability (HECC) on the Pleiades supercomputing cluster, located at NASA Ames. The project is being supported by NASAs Earth Science Technology Office (ESTO) Advanced Information Systems Technology (AIST-16) Program.

Remote Sensin↗

NASA NTRS2017

High Efficiency Centrifugal Compressor for Rotorcraft Applications

The report "High Efficiency Centrifugal Compressor for Rotorcraft Applications" documents the work conducted at UTRC under the NRA Contract NNC08CB03C, with cost share 2/3 NASA, and 1/3 UTRC, that has been extended to 4.5 years. The purpose of this effort was to identify key technical barriers to advancing the state-of-the-art of small centrifugal compressor stages; to delineate the measurements required to provide insight into the flow physics of the technical barriers; to design, fabricate, install, and test a state-of-the-art research compressor that is representative of the rear stage of an axial-centrifugal aero-engine; and to acquire detailed aerodynamic performance and research quality data to clarify flow physics and to establish detailed data sets for future application. The design activity centered on meeting the goal set outlined in the NASA solicitation-the design target was to increase efficiency at higher work factor, while also reducing the maximum diameter of the stage. To fit within the existing Small Engine Components Test Facility at NASA Glenn Research Center (GRC) and to facilitate component re-use, certain key design parameters were fixed by UTRC, including impeller tip diameter, impeller rotational speed, and impeller inlet hub and shroud radii. This report describes the design effort of the High Efficiency Centrifugal Compressor stage (HECC) and delineation of measurements, fabrication of the compressor, and the initial tests that were performed. A new High-Efficiency Centrifugal Compressor stage with a very challenging reduction in radius ratio was successfully designed, fabricated and installed at GRC. The testing was successful, with no mechanical problems and the running clearances were achieved without impeller rubs. Overall, measured pressure ratio of 4.68, work factor of 0.81, and at design exit corrected flow rate of 3 lbm/s met the target requirements. Polytropic efficiency of 85.5 percent and stall margin of 7.5 percent were measured at design flow rate and speed. The measured efficiency and stall margin were lower than pre-test CFD predictions by 2.4 percentage points (pt) and 4.5 pt, respectively. Initial impressions from the experimental data indicated that the loss in the efficiency and stall margin can be attributed to a design shortfall in the impeller. However, detailed investigation of experimental data and post-test CFD simulations of higher fidelity than pre-test CFD, and in particular the unsteady CFD simulations and the assessment with a wider range of turbulence models, have indicated that the loss in efficiency is most likely due to the impact of unfavorable unsteady impeller/diffuser interactions induced by diffuser vanes, an impeller/diffuser corrected flow-rate mismatch (and associated incidence levels), and, potentially, flow separation in the radial-to-axial bend. An experimental program with a vaneless diffuser is recommended to evaluate this observation. A subsequent redesign of the diffuser (and the radial-to-axial bend) is also recommended. The diffuser needs to be redesigned to eliminate the mismatching of the impeller and the diffuser, targeting a slightly higher flow capacity. Furthermore, diffuser vanes need to be adjusted to align the incidence angles, to optimize the splitter vane location (both radially and circumferentially), and to minimize the unsteady interactions with the impeller. The radial-to-axial bend needs to be redesigned to eliminate, or at least minimize, the flow separation at the inner wall, and its impact on the flow in the diffuser upstream. Lessons were also learned in terms of CFD methodology and the importance of unsteady CFD simulations for centrifugal compressors was highlighted. Inconsistencies in the implementation of a widely used two-equation turbulence model were identified and corrections are recommended. It was also observed that unsteady simulations for centrifugal compressors require significantly longer integration times than what is current practice in industry.

Centrifugal compressor↗

NASA NTRS2015

Advanced Computing Support at NASA Advanced Supercomputing (NAS) Division

NAS (NASA Advanced Supercomputing) Division: Advanced Computing: High-End Computing Capability (HECC) Project; Quantum Artificial Intelligence Lab (QuAIL); NASA Earth Exchange (NEX); Data Analytics Infrastructure for NASA; Cloud Services for Science & Engineering Projects.

Advanced Computing↗

NASA NTRS2018

NASA Blazes a Different Path to Energy-Efficient Supercomputing

For years, NASA had a very straightforward process for replacing high-performance computing hardware: over a three-year period, when it became more expensive to operate an older suite of hardware than it did to replace it with new products that could accomplish the same work, we simply replaced the old hardware. For NASA’s High-End Computing Capability (HECC) Project, that process changed when we reached the limits of our facility’s power, cooling, and floor-loading capacity, becoming a strategy of decommissioning the least productive hardware and replacing it with more capable counterparts. The impact was that we provided our users with less supercomputing capability than we would have without the limitations. Additionally, with 25% of our total power consumption going to cool our systems and 50,000 gallons of water per day being evaporated, we wanted a solution that would expand our compute facility while being sensitive to the impact on our environment.

Thigpen, William↗

NASA NTRS2019

The Evolution of NASA’s High-End Computing Capabilities

For over 35 years, the NASA Advanced Supercomputing (NAS) Division at Ames Research Center has housed and managed the U.S. space agency’s largest supercomputing assets. Focused on high-end computing technologies, efficient operations, and user success, the NAS Division has worked with industry to deploy a series of highly successful systems that enable scientific and engineering achievements across NASA. The complementary role of the High-End Computing Capability (HECC) project is evolving to meet NASA’s future challenges in returning to the Moon as a pathway to Mars, while continuing exciting research in aeronautics, space exploration, and Earth science.

Thigpen, William↗

NASA NTRSDate not supplied

NASA's Unsteady Pressure-Sensitive Paint Research and Operational Capability Developments

In the last three years, several advancements have been made to produce a new state-of-the-art capability in the field of Aerosciences. NASA’s Aerosciences Evaluations and Test Capabilities (AETC) Portfolio Office has funded a multi-year project to produce the unsteady Pressure-Sensitive Paint (uPSP) technology as an operational capability in key ground test facilities at NASA. The research and development has primarily been conducted at NASA Ames Research Center’s (ARC) Unitary Plan Wind Tunnel (UPWT) 11-by 11-ft Transonic Wind Tunnel (TWT). The NASA ARC UPWT is one of the ground test facilities under NASA AETC’s Portfolio Office. AETC’s goals are to provide the tools to deliver the technology innovations and breakthroughs necessary to address increasingly complex research and development challenges. AETC’s integrated approach will consider the complimentary high-end compute capabilities necessary to advance analysis in conjunction with ground experimental capabilities. The uPSP Capability Challenge Project is a demonstration of several different technologies: 1) the unsteady Pressure-Sensitive Paint (uPSP) technology, and 2) Project: Red Rover, establishing a secure, reliable, fast connection between experimental and computation facilities, leveraging NASA’s computational resources within the High-End Compute Capability (HECC) Project for processing, storing, and sharing data efficiently. This project demonstrates the technical diversity and technical inclusion need to advance the field of Aerosciences. The approach to combine subject matter experts in experimental methods, optical methods, production wind tunnel testing, network engineering, high-end computing, signal processing, grid generation, and visualization while establishing the required infrastructure for subject matter experts to have access to the data while the wind tunnel test is being conducted. The most recent advancements for the uPSP technology have focused on three key areas: development of data products, robust processing pipeline, operational efficiencies and uncertainty quantification.

buffet↗

NASA NTRSDate not supplied

A Machine Learning Ready Dataset of Acoustic Power Maps for Detection of Active Region Emergence

The development of an accurate forecast for solar eruptive activity has become increasingly important in order to prevent any potential impact on activities in space and the Earth's environment. It is therefore crucial to detect active regions before they appear on the solar surface and create early warning capabilities for upcoming Space Weather disturbances. In this work, 9TB of solar data (SDO/HMI dopplergrams, magnetograms and continuum intensity maps) involving the emergence of 61 NOAA solar active regions since 2010 were processed using the NASA HECC capabilities. An acoustic power maps time-series dataset was created (for four different frequency ranges and processed to take into account the solar sphere geometric effect ) which can be used for understanding the dynamics of the solar surface and train a variety of ML models. The calculated acoustic power maps carry precursor information associated with the decrease in continuum intensity on the solar surface, verifying older helioseismology research. Our results show that a Long Short-Term Memory (LSTMs) model, with a modest layer depth and the right hyperparameters tuned, when trained on this solar acoustic power maps dataset can predict without false negatives a drop in intensity (associated with the emergence of the active region), up to 18 hours in advance.

SMD↗

NASA NTRSDate not supplied

A Comparative Study of Contrail Frequency Indices and GOES-16 Contrail Data Set

Contrail formations have been shown to contribute to the greenhouse effect: they are practically transparent to incoming solar radiation and do little to reflect heat away from Earth but are highly effective at trapping heat within Earth’s atmosphere. To understand the impact contrails have on climate change, contrail frequency indices (CFIs) can be used as a method to quantify aircraft-induced persistent contrails. These indices are capable of tracking long-term contrail formation and identify regions of airspace with the highest contrail formation rates. In this aper, an algorithm is proposed which is capable of using NASA Sherlock and Global Forecast System (GFS) datasets and computing CFIs over large geographic regions and long temporal intervals using NASA Ames’ High-End Computing Capability (HECC) supercomputing system. CFIs are computed using nowcast weather data and previously flown flight tracks. This paper calculated the CFIs of all twenty Air Route Traffic Control Centers in the National Airspace System on October 28th, 2019 and compared the distribution of non-zero CFIs with observed contrail data collected from GOES-16 Satellite data in order to assess the accuracy of the CFI system as a contrail prediction model. It was ultimately determined that the computed CFIs were broadly distributed in the same way as the GOES-16 contrail data and that the individual CFIs computed at the latitude/longitude points at which GOES-16 contrail masks were available had high precision and recall (at 0.75 and 0.86 respectively). While these validation results bode well for the accuracy of the CFI method, the number of provided GOES-16 masks was quite small. Future work should aim to increase the size of the GOES-16 dataset in order to perform a more comprehensive comparison between these two datasets.

Contrails↗