Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fuel-Cladding Chemical Interaction (FCCI)”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Magnification Determination for AGHCF Metallographic Images

Metallographic images generated in the Alpha Gamma Hot Cell Facility (AGHCF) have been used for quantitative and qualitative characterization of irradiated metallic fuel pins. Individual high-magnification images (micrographs) contained in AGHCF file folders and experimental notebooks are in the form of polaroid photographs labeled with AGHCF identification number, magnification, and surface condition (as-polished or etched). Low magnification composite images (photomosaics) are also available for fuel cross sections, for radial strips from the fuel center to the cladding outer diameter, and for circumferential strips of the cladding and outer fuel region. The individual images do not have scale bars. Only a few of the composite images contain scale bars. The purpose of this work is to describe and apply methods for checking the magnification (50X to 500X) of individual images and for determining the magnification (~25X to ~100X) of composite images. The metallographic images used to verify and/or determine magnification were generated during the 1989 to 1993 timeframe for cross sections of U-10Zr/HT9 fuel rods irradiated in EBR-II and for cross sections of irradiated U-10Zr/HT9 fuel-rod samples following elevated-temperature tests conducted in the out-of-pile AGHCF Fuel Behavior Test Apparatus (FBTA). Procedures are documented in the AGHCF Operations Manual for preparation of metallographic samples, for calibration verification, and for constructing composites from individual images. Calibration verification of magnification was performed at least semiannually. One standard used for calibration verification was a glass slide with vertical lines indicating distances of 1 mm, 0.1 mm and 0.01mm. Guidance is provided in the current work for determining magnification from images of the standard. In addition to the periodic calibration verification, consistency checks are recommended to verify the magnification of images taken between the routine calibration verifications. For cladding samples with or without significant fuel-cladding chemical interaction (FCCI), images taken at different magnifications (e.g., 150X and 200X) of the unaffected cladding thickness can be compared. This process is independent of changes in cladding thickness due to swelling and creep. For images taken at only one magnification of cladding regions with no FCCI, the cladding thickness determined from the images may be compared to the nominal as-built cladding thickness (15.0 ± 0.5 mils for examples used in current work)). This procedure works best for cladding that has not experienced significant swelling and/or creep (e.g., ≤2% circumferential strain at the cladding outer surface). Composite images were constructed by pasting together higher magnification images and photographing the composite to generate a negative from which the hard-copy photograph was developed. The primary purpose of the composite images was to identify interesting areas of the fuel and cladding for imaging at higher magnification. However, procedures are recommended in the current work for determining composite magnifications to allow quantitative characterization of the fuel. Composites are not recommended for determining cladding thickness or FCCI depth because magnifications are too low (generally ≤110X) and image contrast is low. Fuel cross-section composites were created by pasting together 50X or 75X images. The nominal magnification for the photographed fuel cross-section composites is 25.4X. A more precise magnification can be determined by comparing the average cladding outer diameter measured from the composite to the average cladding outer diameter measured by profilometry. Radial-strip composites were constructed by pasting together high-magnification (150X or 250X) images. The nominal magnification of radial-strip composites photographs is about 100X. A more precise method for determining the magnification of radial strips is to compare the cladding thick

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

A Design and Fabrication Options Trade Study for Metallic Fuel without Internal Sodium Bonding

Nuclear fuels using alloys of uranium, or metallic fuels, have many beneficial properties. The classical metallic fuel design uses a loose fitting cylindrical “slug” of fuel placed inside stainless-steel cladding tubes where the gap is filled with sodium. This sodium bond is liquid at operating temperature and conducts heat from the slug to the cladding, especially in early life before fuel swells into contact with the cladding. Despite the benefits of sodium bonding, there is a desire to develop metallic fuel technologies without it chiefly to reduce chemical reaction hazards in spent fuel storage from sodium fast reactors operating on once-through fuel cycles. Elimination of the sodium bond may also help unlock potential benefits for fuel fabrication, reactor neutronics, and compatibility with other types of reactors. Creating a sodium-free metallic fuel revolves around the problem of manufacturing fuel slug geometries which are in close contact with the cladding at beginning of life to facilitate heat transport while alleviating fuel-cladding chemical interactions (FCCI) at this interface and providing enough free volume to accommodate fuel swelling. Accelerating development and qualification of this fuel system will require careful selection of design and manufacturing options. To this end, a design trade-off study was performed to evaluate candidate options. Several design and manufacturing options were assessed, weighted, scored, and ranked with respect to fabrication, normal reactor operation, off-normal scenarios, and back-end considerations. This effort was performed both for “baseline” needs, which represented a once-through fuel cycle at temperatures and burnups known to be viable for sodium-bonded metallic fuel, and for “enhanced” needs to represent opportunities for closed fuel cycles and/or more aggressive temperatures/burnups. The outcomes of this study prioritized a baseline technology using U-Zr alloy with additives to mitigate FCCI, produced in annular slug geometry by continuous casting, clad in austenitic stainless-steel alloy, and followed by a final step to swage the cladding down to close the gap. This study prioritized an enhanced fuel technology using U-Mo alloy, also produced by continuous casting into an annular geometry, followed by coating/plating with an FCCI barrier on the slug, again with a final step to swage the cladding diameter down using oxide dispersion strengthened steel. It was noted that development of the enhanced fuel technology would entail more risk, thus U-Zr alloy was put forth as a backup to U-Mo if challenges are encountered with FCCI barriers, and advanced ferritic/martensitic steels are put forth as a backup to oxide dispersion strengthened steels if swaging and welding are found unworkable.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Post-irradiation Examination Status for the BSU-269 Project

High-density uranium inter-metallic uranium silicide (U 3 Si 2 ) was initially considered as a potential advanced nuclear fuel for light water reactor (LWR) systems due to several advantages it demonstrated in thermophysical properties, chemical, and irradiation stability. In addition to understanding the basic thermophysical and mechanical properties of U 3 Si 2 under LWR irradiation conditions, it is important to assess its performance with advanced claddings such as FeCrAl, SiC, or conventional Zr-based claddings. Several aspects of the fuel cycle and fuel performance are being evaluated for U 3 Si 2 coupled with different types of claddings. To thoroughly characterize the U 3 Si 2 -cladding system, their chemical compatibilities and the potential for fuel-cladding chemical interaction (FCCI) must be addressed. Interdiffusion studies have been performed between U 3 Si 2 /Zry-4 and U 3 Si 2 /FeCrAl using diffusion couples. For the U 3 Si 2 /Zry-4 system, ZrSi 2 was the primary interdiffusion product observed at 800°C in addition to other secondary phases from the Zr alloying elements such as Fe and Cr. Low melting point U 6 Fe was also observed at 1000°C. For the U 3 Si 2 /FeCrAl system, at temperatures above 500°C, chemical diffusion Fe-U and Fe-U-Si was observed, increasing with rising temperatures. Although information from these non-irradiated tests is a fundamental first assessment, follow-up with focused irradiation tests is necessary. Irradiation can significantly alter the structure and evolution of the FCCI layers compared to the non-irradiated conditions.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Improvement of mechanistic fuel-cladding chemical interaction modeling in BISON

This report describes work performed during FY2024 under the auspices of the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program to inform and improve mechanistic models of fuel-cladding chemical interaction (FCCI) in metallic fuel. For fuel-side FCCI, atomistic simulations were performed to determine the diffusivity of iron (Fe) in the $\alpha$ and $\gamma$ phases of uranium (U). A model of liquid penetration of cladding due to melting of the fuel-side FCCI region was updated to account for the finite size of the FCCI region, and the model was validated through comparison with tests performed in the Fuel Behavior Test Apparatus (FBTA). For cladding wastage formation, a reduced-order model was improved by comparison with a multi-scale mechanistic model to better quantify the ROM parameters.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Diffusion Behavior of Oversized Fission Products in bcc Fe Cladding: A First-Principles Study

Fuel-Cladding Chemical Interaction (FCCI) poses significant challenges in nuclear reactors, where fission products from nuclear fuel interact with Fe-based cladding materials, potentially compromising their structural integrity. This study investigates the diffusion behavior of oversized fission products, Pr, Nd, Ce, and La, within bcc Fe cladding using density functional theory (DFT), nudged elastic band (NEB) method, and self-consistent mean field (SCMF) theory. Our results reveal significant long-range vacancy binding energies, particularly up to the 6th nearest neighbor, with La exhibiting the strongest binding affinity, followed by Nd, Ce, and Pr. The NEB calculations indicate significant high barriers for the dissociation of 1nn vacancy-solute pairs for all fission products. The tracer diffusion coefficients of these fission products was derived in Arrhenius form. The significant trapping effect of vacancies by a very dilute amount of fission products reduces vacancy mobility, leading to an oversaturation of point defects, void nucleation, and swelling. These are critical issues for irradiated cladding materials. The tracer diffusion coefficients indicate that Nd diffuses the fastest, followed by La, Ce, and Pr. This study provides essential insights for developing advanced cladding materials and design strategies to mitigate FCCI, ultimately enhancing nuclear reactor safety and performance.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Multilayer Architecture Barriers for High Temperature Nuclear Applications

Innovative thin film multilayer metal/ceramic barrier coatings have been developed by Argonne National Laboratory to protect fuel cladding against different phenomena that can be encountered under the harsh operating conditions of advanced nuclear reactors. One phenomenon is Fuel-Cladding Chemical Interaction (FCCI), which can represent a challenge to the performance of steel-clad metallic fuels in sodium-cooled fast reactors (SFRs), especially when operating to high burnups at elevated cladding temperatures, and long fuel residence time. Another phenomenon is the corrosion of zirconium-based cladding under prototypic boiling water reactor (BWR) conditions and associated cladding during off normal conditions, including loss of coolant accidents (LOCA). This work provides details of the development and testing of a thin film (few microns) multilayer metal/ceramic (CrY/Y 2 O 3 ) coatings on steel cladding and its performance against FCCI. The coating architecture evolved through systematic mechanical testing, radiation tolerance assessments, and high-temperature diffusion studies from a preliminary multilayer concept to an optimized high-performance design. The optimized structure leverages stoichiometric Y 2 O 3 for its exceptional radiation stability, chemical inertness, and ultra-low fission product diffusivity (e.g., Ce diffusivity ~10 -20 m 2 /s in irradiated Y 2 O 3 at 650 °C). This is paired with ductile chromium-rich interlayers (Cr 95 Y 5 ), which significantly enhance fracture toughness and mechanical resilience. Design refinements, including increased ceramic layer thickness and optimized Cr–Y interlayer composition, eliminated fracture propagation and preserved coating integrity under extreme mechanical stress (>10× typical reactor conditions) and prolonged radiation exposure (~300 dpa). Those conditions are well beyond expected conditions during normal operations in SFR, and cover some of the transient conditions as well. In addition, the coating deposition was demonstrated to be applied uniformly to the inner surface of steel tubes representing prototypic SFR cladding. Another phenomenon under consideration in this work is the corrosion of zirconium-based cladding under prototypic boiling water reactor (BWR) conditions and associated off normal conditions including loss of coolant accident (LOCA). Another multilayer thin film coating is considered for mitigation of this phenomenon, where a coating of yttrium aluminum and yttrium aluminum ceramic/metal thin film coating. Preliminary results on the coating performance during high temperature thermal cycling (up to 1000 C) have shown promising performance of the coating. On-going optimization of the coating will continue in FY26.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

Results of Oklo Diffusion Couple Experiments

Through the Gateway for Accelerated Innovation in Nuclear (GAIN) initiative, the U.S. Department of Energy funded a GAIN Nuclear Energy Voucher to perform out-of-pile experiments related to the fuel design for Oklo Inc., headquartered in Santa Clara, CA. GAIN’s goal is to accelerate the innovation and application of advanced nuclear technologies, and voucher recipients do not receive direct financial awards but are provided access to national laboratory capabilities at no cost. This report documents the results of diffusion couple experiments performed as part of the GAIN-funded project for Oklo. This work addresses the specific problem of filling the gap in understanding of the fuel-cladding chemical interaction (FCCI) that result from the past focus on a particular fuel design. These knowledge and mechanistic modeling gaps make it difficult to extrapolate from prior fuel performance data to advance an economically competitive fuel design. Specifically, the current state-of-the-art fuel performance modeling cannot separate the entangled effects of temperature ranges, burnups, materials, and geometries.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Fuel Performance Analysis of Fast Flux Test Facility MFF-3 and -5 Fuel Pins Using BISON with Post Irradiation Examination Data

Using the BISON fuel-performance code, simulations were conducted of an automated process to read initial and operating conditions from the Pacific Northwest National Laboratory (PNNL) database and reports, which contain metallic-fuel data from the Fast Flux Test Facility (FFTF) MFF Experiments. This work builds on previous modeling efforts involving 1977 EBR-II metallic fuel pins from experiments. Coupling the FFTF PNNL reports to BISON allowed for all 338 pins from MFF-3 and MFF-5 campaigns to be simulated. Each BISON simulation contains unique power and flux histories, axial power and flux profiles, and coolant-channel flow rates. Fission-gas release (FGR), fuel axial swelling, cladding profilometry, and burnup were all simulated in BISON and compared to available post-irradiation examination (PIE) data. Cladding profilometry, FGR, and fuel axial swelling simulation results for full-length MFF metallic pins were found to be in agreement with PIE measurements using FFTF physics and models used previously for EBR-II simulations. The main two peaks observed within the cladding profilometry were able to be simulated, with fuel-cladding mechanical interaction (FCMI), fuel-cladding chemical interaction (FCCI), and thermal and irradiation-induced creep being the cause. A U-Pu-Zr hot-pressing model was included in this work to allow pore collapse within the fuel matrix. This allowed better agreement between BISON-simulated cladding profilometry and PIE measurements for the peak caused by FCMI. This work shows that metallic fuel models used to accurately represent fuel performance for smaller EBR-II pins may be used for full-length metallic fuel, such as FFTF MFF assemblies and the Versatile Test Reactor (VTR). As new material models and PIE measurements become available, FFTF MFF assessment cases will be reassessed to further BISON model development.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Effective Lanthanide Diffusivity through U-Zr Metallic Fuel

Fuel-cladding chemical interaction (FCCI) is one of the main concerns for the performance of U-Zr metallic fuels. Although FCCI results in complex phase transformations and morphological changes in both the fuel and cladding sides of the interface, the formation of a brittle layer in the cladding side of the interface (sometimes referred to as wastage) has one of the most significant impacts on the cladding mechanical integrity. This brittle layer is associated with the formation of intermetallic compounds between the cladding constituents Fe, Cr and the lanthanide fission product species. The formation of this cladding wastage layer has been the focus of recent efforts to develop a mechanistic modeling framework, including production of lanthanides in the fuel, transport through the fuel to the fuel-cladding interface, and phase transformation to form intermetallic phases. To calculate the rate of transport of lanthanides through the fuel, a multi-scale computational approach has been used. Atomistic calculations have been performed to determine the diffusivities of Nd, the most prevalent lanthanide species, through the solid fuel matrix and along pore surfaces. These diffusivities have been used as input parameters for a mesoscale model to determine an effective diffusion coefficient that accounts for the formation of porosity, its interconnection, and infiltration with bond sodium from the fuel-cladding gap. The effective diffusivity has been used in engineering-scale simulations using the BISON fuel performance code, and BISON simulations have been compared to representative validation cases from the EBR-II reactor.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Multi-scale modeling of wastage layer formation in metallic fuel cladding

Fuel-cladding chemical interaction (FCCI) is a major concern for U-Zr metallic fuels' performance, primarily due to the formation of a brittle layer (wastage) in the cladding. This brittle layer, resulting from intermetallic compounds between cladding constituents Fe, Cr, and lanthanide fission products, significantly impacts the cladding's mechanical integrity. Recent efforts focus on developing a mechanistic modeling framework to understand lanthanide production, transport to the fuel-cladding interface, and phase transformation to intermetallic phases. A multi-scale computational approach has been used to calculate lanthanide transport rates, with atomistic calculations determining Nd diffusivities through the solid fuel matrix and along pore surfaces. These diffusivities inform a mesoscale model to determine an effective diffusion coefficient, accounting for porosity and infiltration with bond sodium. This effective diffusivity is used in engineering-scale simulations via the BISON fuel performance code, which has been validated against EBR-II and FFTF reactor experiments.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

EDS Analysis of FCCI in AFC-FAST Fuel Pins

The Advanced Fuel Campaign’s Fission Accelerated Steady-state Testing (FAST) program uses metallic fuel pins with small diameters to reach a desired burnup more quickly. This enables accelerated testing of advanced fuel designs and decreases the time between idea conception and commercial usage. Post-irradiation examination is critical in this process, especially with respect to the fuel-cladding chemical interactions (FCCI). In this work, energy dispersive X-ray spectroscopy (EDS) is used to track how elements from the fuel and fission products have diffused through the cladding. Elemental redistribution along the fuel-cladding interface is mapped and FCCI region thicknesses are measured. The correlations between geometry, temperature, burnup, and FCCI thickness are presented.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

TEM characterization of two variants of fuel cladding chemical interaction in a HT-9 Clad U-10Zr Fuel. Variant 1: FCCI with a Zr Rind

Here, this study investigated the fuel cladding chemical interaction (FCCI), a key factor that limits operational temperature and burnup, in an HT-9 clad U-10Zr nuclear fuel sample irradiated to a high burnup of 13.1 at.% at a time-averaged peak inner cladding temperature (PICT) of 530 °C. Previous results showed this fuel sample exhibited two distinct levels of FCCI at d. This paper analyzed the FCCI at an azimuthal position showing an interdiffusion layer of <10 µm using transmission electron microscopy to examine chemical and crystallographic nature of phases at the fuel-cladding interface at the nanoscale level. A ZrC layer and a Zr 3 Si phase were identified at the interface; these, along with the relatively low local temperature, potentially contributed to limit interdiffusion, behaving as inhibitors for deleterious interactions. Lanthanides (Ln) partially consumed the ZrC layer and interacted with Fe, forming a Zr-Ln compound and a (Zr,Ce)Fe 2+x phase while also infiltrating up to 4 µm into the cladding. Neither U nor Zr were observed in the cladding, whereas Fe diffused up to 3–5 µm in the fuel. Fe infiltration formed a ternary U-Zr-Fe ε-phase and likely promoted the precipitation of a Cr-rich α’ phase on the cladding interface. Additionally, a Cr-rich χ-phase, likely formed by the dissociation of pre-existing M 23 C 6 carbide precipitates, was identified about 2–5 µm from the fuel-cladding interface. Irradiation-induced nano-voids were also observed in the HT-9 bulk. These findings provide critical insights into FCCI mechanisms at representative irradiation conditions, essential for developing models simulating in-pile metallic fuel behaviors for next-generation reactors.

36 - MATERIALS SCIENCE↗
DOE OSTI2022

Transmission electron microscopy characterization of the fuel-cladding chemical interactions in HT9 cladded U-10Zr fuel

Fuel cladding chemical interaction (FCCI) is a key phenomenon needs to be better understood to establish the design basis for U-10Zr metallic fuel performance. Characterizing the microstructure and chemical composition of FCCI at micron and sub-micron scale is critically important toward a more mechanistic understanding of FCCI phenomenon and its potential effects on cladding integrity and metallic fuel performance. This paper, by using transmission electron microscopy, investigated the FCCI region in HT9 cladded U-10Zr fuel irradiated to 5.7% FIMA burnup at a peak inner cladding temperature of 615 °C in Fast Flux Test Facility (FFTF). Four distinct layers are identified in the FCCI region. The migration of Fe into the fuel side leads to the formation of several U-Zr-Fe ternary phases, including ?-Fe0.5Zr0.32U0.18, e-Fe0.3Zr0.4U0.3, and ?-Fe0.06Zr0.23U0.71, mingled with UFe2, U6Fe, and U phase at various Fe penetration depth up to ~ 150 µm. On the cladding side, grain coarsening and significant lanthanides infiltration along grain boundaries are observed. Laves phase, (Fe,Cr)2(Mo,W), which typically does not exist in fresh HT9, is identified in a wide radial range in the cladding. The typical HT9 martensitic lath structure and pre-existing M23C6 precipitates disappear, partially or completely, depending on the radial distance from the fuel-cladding interface. Those microstructural and compositional changes could cause mechanical degradation in the HT9 cladding. The present characterization results will improve the understanding of FCCI phenomenon and facilitate the development of microstructure-informed FCCI modeling for metallic fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Advanced Characterization of Fuel-cladding Chemical Interaction between U-10Zr Fuel and HT9 Cladding Tested in Fast Flux Test Facility

Fuel cladding chemical interaction (FCCI) can greatly accelerate the cladding failure. However, due to the limited space in a fuel cladding assembly, it is historically challenging to gain an mechanistical understanding of the formation mechanism of FCCI and its influence on fuel and cladding performance. With the imminent need to qualify U-10Zr based metallic fuel cladded by HT-9 for advanced reactors demonstration project, it is of vital importance to use advanced characterization method to study FCCI in a unprecedent detailed manner and gain better mechanism understanding of FCCI. Mechanistic Fuel Failure (MFF) series of prototypic fuel elements irradiated in FFTF [1, 2] provides the best samples to study FCCI since the MFF-series assemblies had an axial fuel height the same as proposed length by industry partners. Jason et al. [3] has performed preliminary post-irradiation examination on a MFF fuel pin sample, which was extracted from the HT9 cladded U-10at.%Zr MFF-3 pin MFF-3 pin (#193045) at an axial location of X/L = 0.98. This sample has a peak burnup of 5.7 at.% and peak inner cladding temperature (PICT) of around 615 °C during in-core testing. Scanning electron microscope examination has identified visible FCCI region on more than half of the HT9 circumference [3]. The most striking feature are grain boundary attacking by apparently lanthanides (Lns) rich phase. However, SEM cannot provide accurate assessment of phase and concentration of grain boundary phases and prevented a better understanding of the formation mechanism of such attach. This study, by pairing transmission electron microscope (TEM) characterization and atom probe tomography (APT) techniques with in-situ micro-tensile testing in scanning electron microscope (SEM), aims at gaining in-depth understanding on the formed FCCI region. The identified FCCI region roughly consists of multilayers as illustrated in Figure 1 (c). The main findings are: (1) layer-B shows observable lanthanides (Lns) infiltration along grain boundaries and mechanical softening due to FCCI- and irradiation-induced microstructural and microchemistry changes, particularly the recovery of martensitic lath structure and dissolution of pre-existing M23C6 together with the formation of coarsened Laves phases, (Fe, Cr)2(Mo, W); (2) layer-C is Fe depleted but Lns significantly enriched, becoming very brittle; (3) layer-D is mainly composed of UFe2 and Lns; (4) three FCCI-induced intermetallic U-Fe-Zr phases, ? (Fe0.5Zr0.32U0.18), e (Fe0.3Zr0.4U0.3), ? (Fe0.06Zr0.23U0.71), were identified near layer-E; (5) the ? (Fe0.5Zr0.32U0.18) phase was characterized to be a face centered cubic (FCC) crystal structure. These results will help to better understanding the governing mechanism of FCCI and facilitating the development of theoretical model for assessing the performance of metallic fuel and cladding integrity.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Effect of TiN coating on suppressing Ce-Fe interaction under irradiation

Advanced cladding is critical for fast reactors with the adequate thermal conductivity, mechanical stability and radiation tolerance of the cladding base material, corrosion resistance and high temperature coolant compatibility of the cladding surface, and chemical stability of the cladding inner wall against fuel cladding chemical interaction (FCCI). The preliminary results of recent ion irradiation studies of two diffusion-couple samples of cerium (Ce)/oxide-dispersion strengthened steel (ODS) and Ce/TiN/ODS, irradiated with 80 MeV xenon (Xe) ions to 100 displacements per atom (dpa) at 500°C, are summarized. Significant Ce-Fe interaction occurred in the Ce/ODS sample, and no noticeable Ce-Fe interaction was found in the Ce/TiN/ODS sample. It shows the effectiveness of 1-µm TiN diffusion barrier coated by the pulsed laser deposition on suppressing Ce-Fe interaction, a major contributor to FCCI in cladding. Here, density function theory (DFT) calculations of the impurity diffusivities of Ce and Fe within the Ti sublattice of TiN were performed to assist a mechanistic understanding of the experimental results.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

AFC Metal Fuel Workshop Presentations

Compilation of PowerPoint slide decks from presentations given at the 3rd Annual AFC Metal Fuels Workshop. The purpose of this workshop is to bring the national metallic fuel stakeholders together to discuss status and needs of metallic fuel and review the DOE AFC Metal Fuel R&D. Desired Outcomes - Advance Metallic Fuel Technology: 1. Stakeholder Community Building 2. National Program R&D Accountability, Planning Support, and Increased Stakeholder Advocation.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

The effect of temperature and burnup on U-10Zr metallic fuel chemical interaction with HT-9: A SEM-EDS study

The fuel cladding chemical interaction (FCCI) between Uranium-Zirconium-based metallic fuel and cladding materials during in-pile service is one of the most constraining phenomena affecting the performance of this fuel system. In this study, we investigated the effect of temperature and burnup on the FCCI development in two U-10 wt.% Zr (U-10Zr) fuel samples with HT-9 cladding irradiated as part of the MFF-3 irradiation test in the Fast Flux Test Facility (FFTF). One sample achieved a burnup of 13.1 at.% and operated with an average inner cladding temperature of 530°C, while the other achieved a burnup of 8.5 at.% and was subjected to an average inner cladding temperature of 615°C. Automated scanning electron microscopy (SEM) back-scattered electron (BSE) imaging of entire fuel cross-sections and SEM energy dispersive x-ray spectroscopy (EDS) analysis on specific fuel-cladding interface regions successfully provided a comprehensive characterization of the depth and type of interaction happening under different irradiation conditions. Further, our analysis shows that FCCI development on both fuel and cladding side is strongly influenced by the inner cladding temperature and, to some extent, the formation and integrity of Zr-rich layers between the fuel and cladding, while the impact of burnup and power is negligible. Measured FCCI thicknesses were compared to BISON simulations using both an empirical model based upon legacy data from the Experimental Breeder Reactor II (EBR II) irradiations and a mechanistic model currently under development for the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program, showing satisfactory agreement. Nonetheless, this comparison supports the need for additional microstructural characterization in intermediate ranges of temperature, power, and burnups in prototypic-length pins.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Chemical interaction and compatibility of uranium mononitride and alumina forming austenitic stainless steel

Uranium mononitride (UN) and alumina forming austenitic (AFA) stainless steel are a potential fuel-cladding combination for the lead-cooled fast reactor (LFR). Chemical compatibility between UN and AFA steel needs to be verified before implementation in a nuclear reactor. Diffusion couple experiments at 823 K and 1023 K were conducted for nonirradiated UN samples in contact with as-cast (no thermally grown Al 2 O 3 ) and preoxidized (with thermally grown Al 2 O 3 ) AFA for 500 and 1000 h in an inert environment. Preoxidized AFA exhibited little to no interaction with all UN samples tested at both 823 K and 1023 K, displaying the stability and capability of the Al 2 O 3 layer to prevent chemical interaction and inter-diffusion with UN. Chemical interaction occurs between UN and as-cast AFA. At 1023 K, an aluminum and nitrogen rich phase (likely AlN) formed along the interface of as-cast AFA and UN samples. At 823 K the AlN phase was not prominently observed due to the reduced diffusivity of aluminum through AFA. The aluminum and nitrogen-enriched phase was also observed in a high temperature pressure-assisted test sample of UN and as-cast AFA thermally treated at 1373 K. Finally, in UN samples doped with a low weight percent of UO 2 (< 3 wt%), AlN was not detected along the interface at either temperatures, and an Al 2 O 3 layer likely formed along the interface and prevented further chemical interaction between UN and as-cast AFA.

36 MATERIALS SCIENCE↗