Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Flash sintering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Phase evolution during reactive flash sintering of Li 6.25 Al 0.25 La 3 Zr 2 O 12 starting from a chemically prepared powder

Here, reactive flash sintering (RFS) of a chemically prepared multiphase precursor powder was performed to fabricate Li 6.25 Al 0.25 La 3 Zr 2 O 12 (Al-LLZO) ceramics. This approach allowed for obtaining single-phase dense samples in a remarkably short processing time of 30 s, at a furnace temperature of 600 °C, with an electric field of 50 V cm -1 and a current limit of 150 mA mm -2 . The ceramics display high bulk conductivity of 0.18 mS cm -1 at room temperature. Furthermore, phase evolution is studied by in-situ X-ray diffraction during: i) conventional heating and ii) RFS under current rate mode. As expected, the intermediate phases progressively dissolved into the Al-LLZO matrix by conventional heating. On the other hand, RFS promoted the growth of the intermediate La 2 Zr 2 O 7 , an effect that was overcome by the thermally driven formation of Al-LLZO at higher temperatures. The observed different reaction pathway suggests that RFS can be used for stabilizing phases that are not thermodynamically favored upon conventional heating.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Novel additive manufacturing for plasma facing materials ‐ creating a research pathway for minority students

This project addresses two critical and intertwined challenges in fusion energy, namely the shortage of a broadly trained scientific workforce and the lack of scalable manufacturing solutions for plasma-facing components (PFCs). Through a collaboration among Florida International University (FIU), Miami Dade College (MDC), and Purdue University, the project established structured, reproducible educational and research pathways that recruit and advance students from institutions historically outside the fusion energy enterprise, building the human capital that this field urgently needs. The project integrates the complementary research strengths of FIU and Purdue to investigate flash sintering as a transformative processing route for tungsten-based PFCs. Unlike conventional sintering approaches, flash sintering offers rapid densification at significantly reduced thermal budgets, making it a compelling candidate for fabricating complex tungsten geometries that must withstand extreme plasma-facing environments. Systematic experimental and modeling efforts will elucidate the fundamental mechanisms governing microstructure evolution, grain boundary chemistry, and thermomechanical response during flash sintering — knowledge that is presently lacking but essential for translating this technology into reliable manufacturing practice. The convergence of workforce development and cutting-edge manufacturing research positions this project to deliver measurable, durable impact: a pipeline of fusion-ready researchers cultivated through expanded institutional partnerships, and a validated materials processing framework that accelerates domestic readiness for next-generation fusion reactor construction.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Generation of electric-field stabilized zirconium monoxide secondary phase within cubic zirconia

Flash sintering of cubic yttria-stabilized zirconia has been studied via in situ energy dispersive diffraction. A secondary rocksalt-phase zirconium monoxide was observed emerging from the primary fluorite-phase zirconium dioxide, previously only observed as a thin interlayer at metal-oxide interfaces, upon application of a direct current electric field. The average secondary phase intensity rose over extended flow of direct current through the ceramic, faded upon removal of the field and disappeared entirely upon application of an alternating current electric field. The results indicate that the sustained application of a direct current electric field can result in significant electrochemical reduction of zirconia under high current density conditions. Poor sinterability and cracking under direct current is apparent and potential mechanisms discussed therein.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Electrochemical grand potential-based phase-field simulation of electric field-assisted sintering

Here, an electrochemical grand potential functional was proposed to describe the sintering of an ionic ceramic green body. The resultant phase-field description enables simulation of the consolidation of an arbitrary number of granular particles and their interactions with the surrounding void phase. The model includes the effects of charged vacancies and the associated interactions between internal and applied electric fields. Defect segregation to grain boundaries is also accounted for, as well as enhanced interfacial defect mobilities. The model was parameterized for Y 2 O 3 . Simulations of two-particle systems showed that the applied electric field had an increasingly important impact on neck growth as particle size increased. A sudden rapid increase in temperature occurred for larger field strengths, which has been reported to be correlated to the onset of a flash event in flash sintering. Simulations of many particles showed that internal heat generation by Joule heating was localized at particle–particle contacts (grain boundaries), even though their conductivities were lower than nearby internal particle-void interfaces. A percolative path for ionic charge across the green body and the ceramic sintered solid was thus defined, accelerating the Joule heating process as the porosity of the green body is removed.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Novel High Temperature Carbide and Boride Ceramics for Direct Power Extraction Electrode Applications. Final report

The current project aims to develop new carbide and boride ceramic materials that incorporate different metal elements (e.g., (Hf 1-x Zr x )B 2 , also called ceramic solid solutions) and understand the fundamental composition-processing-structure-property relationships for such materials. Specifically, nano powders and related nano-composites for selected mixed metal carbide and boride materials are synthesized from nano-scale mixed precursors obtained from solution-based processing via heat treatment in inert atmosphere. The obtained fine powders were then consolidated into dense ceramics via a novel flash sintering process. The mechanical properties and thermal oxidation resistance for the obtained materials were evaluated for these materials. It was found that different synthesis routes produced powders with somewhat different characteristics in terms of composition and microstructure, which then led to different properties for the final ceramics. The synthesis and processing methods demonstrated in this study might be adopted for developing other similar high temperature ceramics, while the mixed metal or solid solution ceramic materials obtained from this study might be used as hot electrodes for direction power extraction and other energy-related applications.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2024

Cost effective synthesis of oxide materials for lithium ion batteries

Methods for synthesizing single crystalline Ni-rich cathode materials are disclosed. The Ni-rich cathode material may have a formula LiNi X Mn y M z Co 1-x-y-z O 2 , where M represents one or more dopant metals, x≥0.6, 0.01≤y<0.2, 0≤z≤0.05, and x+y+z≤1.0. The methods are cost-effective, and include methods for solid-state, molten-salt, and flash-sintering syntheses.

Xiao, Jie↗
NASA NTRS1987

Fracture of flash oxidized, yttria-doped sintered reaction-bonded silicon nitride

The oxidation behavior of a slip cast, yttria-doped, sintered reaction-bonded silicon nitride after 'flash oxidation' was investigated. It was found that both the static oxidation resistance and flexural stress rupture life (creep deformation) were improved at 1000 C in air compared to those of the same material without flash oxidation. Stress rupture data at high temperatures (1000 to 1200 C) are presented to indicate applied stress levels for oxidation-dependent and independent failures.

Govila, R. K.↗
DOE OSTI2020

Coupling between interfacial charge and mechanical deformation at high temperatures in ceramics. Final report

Basic research, under this project, has led to new fundamental discoveries in the effect of electric field (and temperature) on diffusion kinetics, electroluminescence and electronic conductivity in ceramic materials. For example, yttria stabilized zirconia sinters in just seconds well below 1000°C, while, at the same time, exhibiting a highly non-linear rise in conductivity, and intense electroluminescence. The phenomenon has been shown to occur in nearly all ceramics whether they are ionic or electronic conductors, or insulators. The rise in conductivity leads to Joule heating but in-situ measurements with a platinum standard at APS and Brookhaven (NSLS-II) have shown that the temperatures are much below what would have been needed to sinter in a few seconds. We have explored the hypothesis that huge concentrations of Frenkel pairs of vacancies and interstitials are produced. While these point defects accelerate sintering (by the interstitials being transported to the pores and the vacancies to the grain boundaries), they may also produce electron-hole pairs which can impart high electrical conductivity or recombine to emit photons. Many measurements, including in-situ measurements of lattice expansion are consistent with this hypothesis. However, the energy barrier for generating Frenkels in zirconia for example is much larger than can be expected at temperature and electrical fields in these experiments. Most recent work suggests that short wavelength phonons play a critical role in the genesis of the “flash” phenomenon. For example, the Debye temperature has been shown to be the lower bound for initiating flash. Molecular dynamics simulations have shown that large concentrations of Frenkel pairs can form under the proliferation of “optical” phonons at the edge of the Brillouin zone, that is with a wavelength at or below the lattice parameter. This project has led to the development of new experimental techniques as well as a software hardware interface for process and control and data analysis in real time, with a time scale of less than one second. This approach spells a new paradigm in materials science research. It potential impact on high rate manufacturing is self evident.

36 MATERIALS SCIENCE↗
NASA NTRSDate not supplied

Process Recipes for Additively Printed Copper Ink Flexible Circuits using Direct Write Methods

In this paper, the process-recipes and process-performance relationships for additive-printing of copper circuits using direct-write methods have been studied. The process has been implemented on the direct write platform. Interest in the use of additive printing methods for the manufacture of micro-circuits has grown immensely in recent times. Direct write methods have been shown to have the ability to create circuits in a limited manner. However, the process recipes and the effect of process parameters on the manufactured properties are not well understood. Copper ink is a good and cost-effective alternative to silver ink but its use has lagged owing to an increased propensity for oxidation. In this paper, photonic curing has been used to sinter copper ink to make the traces conductive. The method flashes high energy light that sinter metal particles instantaneously and the temperature of the substrate remains low. The effect of the different photonic sintering profiles on the mechanical and electrical properties of the printed traces has been studied in this paper.The print process parameters also play an important role in the line width and height that has been studied to print with the desired line profile for the end application. An LC filter circuit is been printed with SMD components been attached using an electrically conductive adhesive (ECA). The manufactured flexible LC filter is been tested for its frequency sweep to compare with the commercially available LC filer with the help of the Bode plot.

Process control↗
DOE OSTI2021

Aerosol jet printed 3 omega sensors for thermal conductivity measurement

The 3 omega (3ω) method is a trusted technique for measuring thermal conductivity—a fundamental material property of critical importance in a broad range of applications. However, traditional 3ω sensor processing requires some form of physical vapor deposition, such as metal evaporation or sputtering. These 3ω sensor deposition techniques limit the materials and sample sizes applicable to the 3ω method. This work demonstrates an aerosol jet printing method to directly print silver 3ω sensors that yield accurate temperature-dependent measurement up to 300 °C on materials with thermal conductivity ranging from 1 to 150 W/m K. The interrelationship between printed sensor geometry, sensor thermal stability, and applicability to the 3ω method is examined. Thermal conductivity measurement with 3ω sensors conventionally sintered at 300 °C agrees to independent laser flash measurement within 4% from room temperature to 150 °C. An unconventional rapid high-temperature sintering method is shown to produce sensors that agree within 3% of the laser flash measurements from room temperature to 300 °C. The rapid sintering profiles also reduced the sensor–substrate thermal boundary resistance of the printed sensors by as much as 88%. The direct printing of 3ω sensors creates opportunities for measurement of thermal transport properties in applications previously inapplicable to the 3ω method.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

Fabrication and thermophysical properties of UO 2 -UB 2 and UO 2 -UB 4 composites sintered via spark plasma sintering

Uranium dioxide (UO 2 ) composites with uranium diboride (UB 2 ) and uranium tetraboride (UB 4 ) have been proposed as advanced fuel candidates due to their high thermal conductivity, high melting point, high fissile density and their ability to incorporate a built-in burnable poison by tailoring the targeted 10 B/ 11 B ratio. As such, it is important to assess the fabrication, and thermal and micromechanical properties of such composites. In this work, UO 2 -UB 2 and UO 2 -UB 4 samples with boride phase fractions of 5, 15 and 30 wt% were fabricated to high densities (above 95 % theoretical density) via spark plasma sintering (SPS). This enabled sintering at relatively low temperatures and short timescales. SPS also aided in maintaining the target phase fractions of the samples as reactions between the constituent phases were suppressed due to the short timescales and reducing environment during sintering. Here, thermal diffusivity measurements from 299 to 1273 K were conducted through laser flash analysis (LFA). The diffusivity increased as a function of boride weight fraction, and UB 2 additions increased the thermal diffusivity of the composites more than UB 4 additions. Assessment of the LFA results indicated in-situ reactions between the UO 2 and boride phases that suppress the thermal diffusivity occur above 800 K for all samples. Oxidation of the boride phase was proposed as the underlying reaction. This was supported by thermodynamic assessments from the literature, as well as microstructural, crystallographic, and nanoindentation characterization performed on these samples.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗