Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Flash sintering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

On the confluence of ultrafast high-temperature sintering and flash sintering phenomena

Ultrafast high-temperature sintering (UHS) and flash sintering are novel methods for rapid sintering of ceramics, often completed in just a few seconds. Here, we show that both also share two additional features: an abrupt rise in electrical conductivity, which is electronic, and electroluminescence. More fundamentally, both are related to phonon physics where MD calculations have shown that proliferation of phonons at the edge of the Brillouin zone can induce Frenkel pairs without the application of electrical fields. Here, we show that, indeed, heating without the application of electric field, can also induce flash: Rapid heating processes of thin films of an oxide-salt deposited on silk fibers, with a propane torch, are shown to induce electronic conductivity, electroluminescence, and rapid sintering of the oxide. Further, the discussion in this article harkens back to two inventions, more than a century ago, which can now be related to flash and UHS: (i) the Nernst glow lamp circa 1900, made from zirconia, and (ii) the Welsbach mantle, constituted from ceria doped thorium oxide, in the late nineteenth century. Thus, the confluence between high heating rate and electric field induced flash phenomena links the past to the new. The emerging question is how injection of phonons that has been shown to create Frenkels can further induce high electronic conductivity and electroluminescence in oxides. Both electronic conductivity and luminescence are likely related to the generation of electron–hole pairs.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Effects of processing conditions on flash sintering of commercial ZrN

Flash sintering (FS) is a potentially rapid and low-cost manufacturing technique for advanced ceramics. There are still many unknowns about ceramic FS, especially for highly conductive high-temperature ceramics (HTC), which often display decreased bulk conductivity with increasing temperature. This study qualitatively characterizes the flash behavior of highly conductive HTC materials using zirconium nitride (ZrN) as an example. The effects of processing parameters (e.g., DC voltage/electrical field strength, voltage ramp rate, post-flash holding time, mechanical pressure, sample milling, and choice of electrode materials) on ZrN flash behavior are also qualitatively studied and linked to samples microstructure and hardness. It is observed that best densification was achieved using 5 min Spex-milled ZrN powder under 25 MPa of applied pressure and constant 8 V DC. The potential mechanism for ZrN FS and the similarity and difference from FS of conventional oxides like YSZ have been proposed based on experimental observations, and the directions for future research are also pointed out.

Flash Sintering↗
DOE OSTI2021

Onset of selective laser flash sintering of AlN

Abstract Flash sintering uses a combination of heating and electric fields to rapidly densify ceramics. Previously, it has been shown that a scanning laser can be used to initiate flash sintering in localized regions on an yttria‐stabilized zirconia (YSZ) sample in a process known as selective laser flash sintering (SLFS). In this work, we show using a combination of measurements of electric current flowing through the sample and observations of necks formed between powder particles that aluminum nitride (AlN) can also undergo SLFS. Scan conditions required to initiate SLFS are characterized over a range of laser powers and laser scan speeds in a dry nitrogen environment. It is shown that initiation of SLFS in AlN is governed by both the local input energy density per scan and heat dissipation and a numerical model is developed to predict temperatures during SLFS. Assuming the minimum temperature along the conductive path determines the onset of SLFS, the minimum temperature and time required is 450–670 K in 2–0.25 s for the pressed AlN pellets used in this study for laser scan speeds of 33–300 m/s, laser powers of 10–30 W, and an applied electric field of 3000 V/cm.

Gouws, Andre↗
DOE OSTI2022

Machine learning-assisted ultrafast flash sintering of high-performance and flexible silver–selenide thermoelectric devices

Flexible thermoelectric generators (TEGs) have shown immense potential for serving as a power source for wearable electronics and the Internet of Things. A key challenge preventing large-scale application of TEGs lies in the lack of a high-throughput processing method, which can sinter thermoelectric (TE) materials rapidly while maintaining their high thermoelectric properties. Herein, we integrate high-throughput experimentation and Bayesian optimization (BO) to accelerate the discovery of the optimum sintering conditions of silver–selenide TE films using an ultrafast intense pulsed light (flash) sintering technique. Due to the nature of the high-dimensional optimization problem of flash sintering processes, a Gaussian process regression (GPR) machine learning model is established to rapidly recommend the optimum flash sintering variables based on Bayesian expected improvement. For the first time, an ultrahigh-power factor flexible TE film (a power factor of 2205 μW m -1 K -2 with a zT of 1.1 at 300 K) is demonstrated with a sintering time less than 1.0 second, which is several orders of magnitude shorter than that of conventional thermal sintering techniques. Further, the films also show excellent flexibility with 92% retention of the power factor (PF) after 10 3 bending cycles with a 5 mm bending radius. In addition, a wearable thermoelectric generator based on the flash-sintered films generates a very competitive power density of 0.5 mW cm -2 at a temperature difference of 10 K. This work not only shows the tremendous potential of high-performance and flexible silver–selenide TEGs but also demonstrates a machine learning-assisted flash sintering strategy that could be used for ultrafast, high-throughput and scalable processing of functional materials for a broad range of energy and electronic applications.

25 ENERGY STORAGE↗
DOE OSTI2022

The influence of the processing parameters on the reactive flash sintering of ZrO 2 -CeO 2

Reactive flash sintering (RFS) is a method that was recently developed to produce dense single-phase bulk ceramic parts through solid-state reactions in a single-step that only takes a few minutes. The influence of the RFS parameters on the phase purity of a simple mixed oxide, (Zr 0.8 ,Ce 0.2 )O 2 , was investigated. Parameters such as furnace temperature, furnace atmosphere, electric current density, and alternating current (AC) or direct current (DC) were examined. It was found that (Zr 0.8 ,Ce 0.2 )O 2 pellets with high densities, above 90% of its theoretical density, can be produced by RFS in a few minutes when RFS occurs under oxidizing atmospheres, AC fields with current densities of 100 mA·mm –2 , and at a furnace temperature of 1200°C. Reducing conditions such as Ar-H 2 atmosphere and DC fields, low furnace temperatures, and low current densities resulted in phase impurities and poor reactions between the ZrO 2 and the CeO 2 powders. These results show that RFS is a useful method to produce mixed oxides, but it is very sensitive to the processing parameters. This is the first time that the influence of most of the RFS processing parameters has been studied systematically. Thus, the present work aims to provide guidelines on selecting the right processing parameters when exploring RFS.

36 MATERIALS SCIENCE↗
DOE OSTI2024

In-situ synchrotron X-ray diffraction of hydroxyapatite-zirconia composite during conventional and flash sintering

Here, we conducted in-situ X-ray diffraction to study the crystalline phase evolution in hydroxyapatite-zirconia composites during both conventional and flash sintering processes. Additionally, we examined the thermal history and microstructure of the composite under these sintering conditions. Despite both sintering methods reaching similar average temperatures, they yielded distinct results in terms of crystalline phase composition and microstructure. In the flash sintered samples, we observed a complete transformation of hydroxyapatite into α- tricalcium phosphate and a complete tetragonal to cubic phase transition in zirconia. Conversely, the conventionally sintered samples remained practically stable. Notably, the flash sintered samples exhibited needle-like microstructures, which were absent in their conventionally sintered counterparts. This divergence suggests that the application of an electric field plays a role in generating athermal effects during the sintering of hydroxyapatite-zirconia composites.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Reactive flash sintering of TiZrN and TiAlN ternary metal nitrides

Here, this study demonstrated the reactive flash sintering (RFS) for two powder mixtures: TiN-ZrN (both conducting) and AlN-TiN (TiN conducting but AlN insulating), targeting ternary metal nitrides (TMN) of Ti 0.5 Zr 0.5 N and Ti 0.5 Al 0.5 N, respectively. A constant volage and pressure (e.g., 8 V DC, ∼15 MPa) at room temperature triggered the flash (current density up to 27 A/mm 2 ) without pre-heating, and the entire RFS process finished in a few minutes. For TiZrN, the flash was instantaneous whereas for TiAlN, there was a long incubation before the flash followed by a quick and dramatic flash. Both conventional ex situ XRD and in situ synchrotron study had been carried out. They showed a uniform Ti 0.57 Zr 0.43 N solution formed in RFS and persisted upon cooling, while (Ti, Al) N solid solution formed at high temperature was not stable and likely went through a very quick phase separation in the cooling process. The final products from RFS had been characterized using SEM/EDS for microstructure. Both TiZrN and TiAlN were dense. Distribution of Ti, Zr, and N was uniform for TiZrN; for TiAlN, Ti and N distribution was uniform, while association of Al with oxygen was observed. TGA-DSC revealed the onset oxidation temperature for TiZrN was comparable to TiN and ZrN, while it was higher by ∼200 °C for TiAlN, likely due to the formation of Al 2 O 3 . In terms of mechanical properties such as hardness or fracture toughness, forming a single-phase solid solution (like TiZrN) does not offer obvious benefits. while large grain size from RFS seemed to be unfavorable. Future optimization of RFS condition and in-depth study by both experiments and simulation are needed to fully understand the composition-processing-structure-property relationships for such TMN from the reactive flash sintering process.

Flash Sintering↗
DOE OSTI2023

The onset of selective laser flash sintering in undoped and doped lanthanum chromite

Previous studies have shown that selective laser flash sintering (SLFS) can be initiated in dielectrics that exhibit ionic or electronic conduction at high temperature. These materials required high laser powers to reach the temperatures where electrical conduction is sufficient to initiate SLFS. In this study, SLFS in lanthanum chromite (LC), an intrinsic electronic conductor with high conductivity, and lanthanum strontium chromite (LSC), which is doped to further increase electronic conductivity, were investigated with a focus on understanding the initiation mechanisms. Results show that the initiation of SLFS in LC and LSC occurs when electronic charge carriers are activated and flow to the electrode where the current is measured. A combination of carriers produced at the electrode, temperature-activated intrinsic charge carriers, and extrinsic charge carriers present in LSC due to doping are responsible for the facile initiation of SLFS.

36 MATERIALS SCIENCE↗
DOE OSTI2021

On the Arrhenius-like behavior of conductivity during flash sintering of 3 mol% yttria stabilized zirconia ceramics

Here, we discuss the Arrhenius behavior of electrical conductivity σ during flash sintering of 3 mol% yttria stabilized zirconia (3YSZ). In situ x-ray diffraction is used to determine sample temperature. Sintering contribution to σ is excluded by investigating the flash event on a dense ceramic. We show that total conductivity follows an Arrhenius-like equation in both dense and green samples, even during Stage II of flash. The non-linearity often verified during flash sintering of 3YSZ is therefore related to the furnace temperature instead of the sample temperature when building the ln(σ) vs. 1/T plots. Furthermore, we verified a change in the activation energy for conduction prior to the ignition of the flash event and discussed the possible mechanisms. For instance, the decrease in activation energy from Stage I to II in the dense sample is attributed to a contribution from electronic carriers.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Controlled current-rate AC flash sintering of uranium dioxide

Uranium dioxide (UO2) pellets with controlled microstructures were densified up to 93.4% of their theoretical density in less than 25 minutes at a furnace temperature of 873 K, utilizing controlled current-rate alternating current (AC) flash sintering (FS). Using this AC-FS method it was possible to control the sintering rate and thermal gradients, resulting in dense pellets with no appreciable hourglassing and good mechanical integrity. Moreover, the apparent sintering activation energy for FS and for conventionally sintered samples was estimated to be 108 kJ mol -1 and 380 kJ mol -1 , respectively using the master sintering curve method. The apparent activation energy for FS was remarkably close to those reported in the literature for spark plasma sintering of UO 2 . Furthermore, both these field assisted sintering methods utilize fast heating rates and electrical effects that are likely enhancing the grain boundary diffusion mechanism. Finally controlled current-rate AC-FS has been demonstrated as a technological advancement, capable of producing ceramic nuclear fuels in a fraction of the conventional processing time.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Modeling of flash sintering of ionic ceramics

A fundamental understanding of the influence of defects in ionic ceramics at the atomic, microstructural, and macroscopic levels, before, during, and after the flash sintering event is key to the development of ceramic processing operations that lead to fast, low cost, and environmentally safe fabrication of materials. The observed phenomenology of the flash process encompasses multiple time and length scales and have resulted on a wide variety of what sometimes appears to be contradictory explanations. Here, this article summarizes the latest developments on the modeling and simulation of flash sintering, specifically those related to the understanding of the equilibrium and kinetic properties and the corresponding microstructural evolution of ionic ceramics. Challenges and opportunities in the development of theoretical analyses that include unidentified multiphysical effects are discussed, as they pertain to the processing of technologically relevant ceramic materials for advanced structures and devices.

36 MATERIALS SCIENCE↗
DOE OSTI2023

In-operando synchrotron experiments of flash sintering carried out in current rate mode

Here, we report first-time results for in-operando flash sintering synchrotron experiments carried out in current rate mode where the specimen, held at a constant temperature, is fed current that is increased at a constant rate. These experiments are unique because the time dependence of the sintering behavior can be stretched out over a longer period (by changing the current rate) than in voltage-to-current experiments in which sintering occurs in a burst at the onset of the flash. Two results are presented: (i) A comparison of temperatures measured with the platinum standard to those predicted by the black body radiation model leading to estimates of the emissivity as a function of porosity whereby emissivity increases from 0.65 to 0.9 as the sample sinters from its green state to full density, and (ii) measurements of the excess lattice expansion as a function of density as the sample sinters continuously while the current is increased. The present work highlights the promise of current rate experiments to obtain results while the sample sinters gradually from its green density to full density (somewhat akin to conventional sintering) for gaining further insights into the mechanisms of flash sintering.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Multicycle flash sintering of cubic Y 2 O 3 -stabilized ZrO 2 : An in situ energy dispersive synchrotron x-ray diffraction study with high temporal resolution

The current induced unit cell volume changes, (111) Bragg peak full width at half maximum (FWHM) and its integrated intensity in 8 % Y 2 O 3 stabilized ZrO 2 (8 %YSZ) solid state electrolyte was monitored during a triple-flash sintering experiment by in situ energy dispersive x-ray diffraction using a polychromatic synchrotron probe (max, photon energy 200 keV) with 2 second temporal resolution. The first spontaneous singularity in the unit cell volume (+0.54 %) was observed at 899 °C under 15 V/mm applied field intensity, which was associated with 13 mA/mm 2 current draw and an increase in density to 97 %. Following anelastic relaxation of the unit cell volume under open circuit conditions, the same applied field was applied twice in a row which resulted in additional induced singularities at 925 °C (+0.48 %) and 944 °C (+0.42 %). A floating baseline, which was above the thermal expansion baseline, was observed from 833 to 969 °C and was attributed to Joule heating. In conclusion, the singularity at 899 °C is associated with a sharp change in (111) FWHM and a 34 % decrease in integrated peak area that was attributed to changes in the distribution of oxygen vacancies and the changes in their concentration as induced by the applied field in the spontaneous transient stage of flash sintering.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Synthesis and Flash Sintering of (Hf1-xZrx)B2 Solid Solution Fine Powders

Fine powders of (Hf1-xZrx)B2 solid solution were synthesized by two methods. In the first one, solution-based processing of HfCl4, ZrCl4, sucrose and H3BO3 was carried out followed by heat treatment (e.g., at 1500 °C for 1 h) in Argon to achieve the carbothermal reduction (CTR) reaction to form the boride solid solution. In the second one, called boron hydride reduction (BHR) method, HfCl4, ZrCl4 and NaBH4 were directly mixed in a glove box followed by heat treatment in Argon at elevated temperatures from 700 to 1500 °C. In addition, the powders synthesized via both methods were flash sintered without sample preheating in a homemade setup. The synthesized powders as well as the flash sintered bulk ceramics were characterized using different techniques including XRD, SEM, EDS, TEM, TGA-DSC, and Vickers hardness test to reveal the inter-relationships between starting materials composition, processing conditions, and the resulting materials microstructure and physical/chemical properties.

Belisario, Jose↗
DOE OSTI2020

Synthesis and flash sintering of (Hf 1-x Zr x )B 2 solid solution powders

(Hf 1-x Zr x )B 2 solid solution powders were synthesized by two methods. First, solution-based processing of HfCl 4 , ZrCl 4 , sucrose, and H 3 BO 3 was conducted followed by heat treatment in Argon to carry out the carbothermal reduction (CTR) reaction to form the diboride powders. Alternatively, in the so-called borohydride reduction (BHR) method, HfCl 4 , ZrCl 4 and NaBH 4 were mixed in an Argon glove box followed by heat treatment in Argon at 700-1500°C. The synthesized powders were characterized by XRD, SEM, TEM, EDS, and TGA, and the influence of different parameters such as starting composition, heat treatment temperature and time on products characteristics were revealed. Both CTR and BHR solid solution powders were then consolidated within ~5 min in a homemade flash sintering (FS) setup. Here, the composition, microstructure, hardness, and thermal-oxidation properties of flash sintered ceramics were characterized, and the implication of this study and directions for future research were discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Phase evolution during conventional and reactive flash sintering of (Mg,Ni,Co,Cu,Zn)O via in situ X-ray diffraction

Reactive flash sintering (RFS) enables the simultaneous synthesis and sintering of ceramics and has been shown to affect the reaction pathway of different materials. Herein, in situ synchrotron X-ray diffraction (XRD) is used to investigate the (Mg,Ni,Co,Cu,Zn)O entropy-stabilized oxide formation during: (i) conventional heating and (ii) RFS under current rate-controlled mode. The same reaction pathway is verified in both instances: the starting rock-salt (RS), spinel (Co 3 O 4 ), tenorite (CuO), and wurtzite (ZnO) phases transform into a single RS phase with a (1 1 1) to (2 0 0) intensity ratio of 0.67, consistent with a random distribution of the cations into the structure. Pt lattice peak shift from the XRD patterns is used as standard to monitor the sample surface temperature, revealing a strong endothermic reaction during the RS single-phase formation (Pt peaks shift toward higher angles while increasing sample temperature/current density). Furthermore, in RFS, the single-phase RS structure is formed in just 60 s at a furnace temperature of 600°C and a current rate of 220 mA mm -2 /min. Therefore, RFS greatly accelerates the synthesis of (Mg,Ni,Co,Cu,Zn)O, however, it does not play a role in the reaction pathway for this material formation.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Reactive flash sintering and characterization of bulk high entropy nitrides

Over the past decade, numerous high-entropy ceramics have been synthesized, often displaying attractive properties. However, the study on facile preparation of bulk high entropy nitrides (HEN) are limited, despite its broad potential applications. This research demonstrates for the first time rapid fabrication (within ∼6 min) of bulk high-entropy nitrides, especially (Al 0.17 Nb 0.17 Ta 0.17 Ti 0.32 Zr 0.17 )N, from binary nitride powder mixtures using a highly efficient reactive flash sintering (RFS) technique. X-ray diffraction (XRD) shows the HENs from RFS are near single-phase solid solutions with a rock salt crystal structure, while in situ synchrotron study carried out during RFS captured in real time the formation of HEN, which was preserved upon cooling, suggesting thermodynamic stability of the HEN phase, even up to extreme pressure (∼35.6 GPa). Microscopic analyses using SEM, STEM, and EDS reveal decent uniformity for HEN with no obvious segregation of elements, even to submicron scale. Some properties of the obtained bulk HENs are consistent with expectations. For example, their hardness and bulk modulus are close to estimates based on rule-of-mixture (ROM) values from the constituent binary nitrides. Meanwhile, some other measured properties seem to show surprises. For example, the fracture toughness for the HENs (e.g., 7.81 ± 1.40 MPa•m 1/2 or higher) turns out to be more than double of the expected ROM estimates. The significantly improved fracture toughness is attributed to the observed nano-layered structure of the HENs, despite the HEN’s cubic crystal structure and high hardness. In addition, the oxidation resistance shows improvement up till ∼800°C, possibly due to Ta doping that suppress oxygen vacancy formation in the oxide shell, while the 5-metal HEN of (Al 0.17 Nb 0.17 Ta 0.17 Ti 0.32 Zr 0.17 )N displays superconductivity (T c of ∼5–7 K from magnetism and resistivity measurements, slightly lower than ROM estimate), despite insulating property of starting AlN. Furthermore, future study combining experimental investigation using larger samples to confirm the observed increase in fracture toughness and oxidation resistance, theoretical modeling at different length scale, and more detailed structural/chemical characterization, especially at the atomic scale, are all needed to fully understand the inter-relationships between composition, processing, structure, and novel properties for these HENs and the development of related new materials for different applications.

Flash sintering↗