Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CsPbBr3”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Investigation of defects in melt and solution grown perovskite CsPbBr 3 single crystals

Recently, there has been considerable interest in x-ray and gamma ray detectors with large volume and high energy resolution that operate at room temperature. To improve detector energy resolution, the carrier mobility-lifetime product needs to be increased, and the electronic trap state concentration needs to be minimized. Defect concentrations in the part per billion range can alter the charge transport and carrier recombination lifetime. In this work, thermally stimulated current spectroscopy measurements were systematically carried out in bulk halide perovskite single crystals of CsPbBr 3 over a temperature range of 80–320 K. The origins and trap parameters of CsPbBr 3 crystals from the solution growth and melt growth procedures were determined and compared. Trap concentrations were ranged from 1 × 10 11 to 1 × 10 16 cm –3 . Appreciable detector performance was observed for CsPbBr3 crystals with trap concentrations less than 1 × 10 14 cm –3 . The comparison of spectral responses of crystal samples grown using two different methods shows that, after purification, solution-grown crystals are comparable to melt-grown crystals in terms of low defect concentration and improved detector performance. Finally, for an improved mobility-lifetime product and enhanced spectral response to high energy radiation from fissile materials, trap states in either type of a crystal ingot must be reduced closer to 10 11 cm –3 .

36 MATERIALS SCIENCE↗
DOE OSTI2023

Local structure, bonding, and asymmetry of $\mathrm{((NH_2)_2CH)PbBr_3}$, $\mathrm{CsPbBr_3}$, and $\mathrm{(CH_3MH_3)PbBr_3}$

Here we report local structure measurements for CsPbBr 3 and ((NH 2 ) 2 CH)PbBr 3 (FAPbBr 3 ) and compare them with recent results for (CH 3 NH 3 )PbBr 3 (MAPbBr 3 ). The Pb-Br bonding is similar for all three systems; the effective spring constants, κ, are comparable (ranging from 1.20 to 1.95 eV/Å 2 ), but small in magnitude indicating very soft materials. However, there are also important differences between the three systems. Static disorder is very small for CsPbBr3 but increases somewhat with the size of the organic molecular ions MA + and FA + . At room temperature, dynamic disorder dominates in all compounds. The thermal disorder of the Pb-Br pair distribution function (PDF), i.e., the Debye-Waller factor σ 2 follows a correlated Debye or Einstein model up to 300 K in CsPbBr 3 (orthorhombic phase), but for FAPbBr 3 and MAPbBr 3 , there is a break in the σ 2 (T) curve at the orthorhombic-tetragonal transition (o-t) near 150 K, indicating a small change in the spring constant κ. κ increases for MAPbBr 3 but decreases in FAPbBr 3 at this transition. These changes are attributed to changes in the H-bonding between Br - and MA + or FA + at this transition, as a result of librations or rotations of these molecular cations. In addition, the Pb-Br PDF becomes asymmetric at a relatively low temperature for FAPbBr 3 and MAPbBr 3 , while this effect is significantly smaller for CsPbBr 3 . Finally, we address the question of a model to explain the asymmetric PDF. Two main models are discussed in the literature, an anharmonic pair potential and a split-pair distribution, possibly driven by the presence of a lone pair on the Pb ion. We show that the fourth cumulant C 4 can differentiate between these two models and other possible models. Experimentally C 4 is positive at 250 K and above, for all three systems and that is inconsistent with a split-peak model, for which C 4 is negative for splittings larger than 0.12 Å.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Phase I Final Technical Report _ RDUSA

During Phase I of this proposal our team focused on meeting the goals proposed in the Phase I project which included identifying the integration approaches and fundamental materials properties (composition, bonding, defects, structure, doping, etc.) defining response to X-ray energies between 10-100KeV and sensitivity >100 μC Gyair-1 cm-2 in perovskite systems with formula CsPbX3 and CsPb2X5 [where X = chlorine (Cl), bromine (Br), iodine (I), or a combination of any of these elements] to enable high-efficiency, low-cost, X-ray detection systems. In the sections below, we summarize the research results that confirm the feasibility of our technical approach. In summary, we have demonstrated X-ray sensitivity >500 μC Gyair-1 cm-2 in the energy range of 10-100 keV using CsPbBr3 films of thicknesses ranging from 8 μm to 500 μm, which is above the technical requirements outlined in the call for proposal.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Correlative analysis of CsPbBr2Hal (Hal = Cl, Br, I) meltcrystallization paramete

Abstract — Metal halide perovskites (MHPs) are an exciting research topic as they have the potential to make solar cells that are both more efficient than current siliconbased designs and have a wider range of applications. In this work the crystallization of CsPbBr2Hal (Hal = Cl, Br, I) halide perovskite melts were studied by the differential thermal analysis method. It was established that the crystallization of CsPbBr2Hal (Hal = Cl, Br, I) melts can be “hot” (i.e., at temperatures above the point of the alloy’s start-melting temperature) or with supercooling. The replacement of the bromine atom with another halogen atom leads to a shift of the dwell temperature range, at which “hot” crystallization takes place, from 830-846 K for CsPbBr3 to 807-832 K for CsPbBr2Cl and 741-768 K for CsPbBr2I. The activation energy of “hot” crystallization decreases in the same order. A linear dependence between the pre-exponential factor (ln(𝑽𝑽𝒄𝒄𝒄𝒄𝒄𝒄𝒔𝒔𝒕𝒕 𝟎𝟎 )) and the activation energy (Ea) of the crystallization process is revealed from the experimental data, proving the compensation effect.

Kopach, O.↗
DOE OSTI2024

Near Room Temperature Solvothermal Growth of Ferroelectric CsPbBr 3 Nanoplatelets with Ultralow Dark Current

CsPbBr 3 exhibits outstanding optoelectronic properties and thermal stability, making it a coveted material for detectors, light-emitting diodes, and solar cells. Despite observations of ferroelectricity in CsPbBr 3 quantum dots, synthesizing bulk ferroelectric CsPbBr 3 crystals has remained elusive, hindering its potential in next-generation optoelectronic devices like optical switches and ferroelectric photovoltaics. Here, a breakthrough is reported: a novel solvothermal technique enabling the growth of ferroelectric CsPbBr 3 nanoplatelets with lateral dimensions in the tens of micrometers. This represents a significant step toward achieving large-area ferroelectric CsPbBr 3 crystals. Unlike traditional methods, this approach allows for growth and crystallization of CsPbBr 3 in alcohol solutions by enhancing precursor solubility. Further this study confirms the ferroelectric nature of these nanoplatelets using second harmonic generation, electrical characterizations, and piezoresponse force microscopy. This work paves the way for utilizing ferroelectric CsPbBr 3 in novel optoelectronic devices, significantly expanding the potential of this material and opening doors for further exploration in this exciting field.

25 ENERGY STORAGE↗
DOE OSTI2022

Solution‐Processed CsPbBr 3 Quantum Dots/Organic Semiconductor Planar Heterojunctions for High‐Performance Photodetectors

Abstract Planar heterojunctions (PHJs) are fundamental building blocks for construction of semiconductor devices. However, fabricating PHJs with solution‐processable semiconductors such as organic semiconductors (OSCs) is a challenge. Herein, utilizing the orthogonal solubility and good wettability between CsPbBr 3 perovskite quantum dots (PQDs) and OSCs, fabrication of solution‐processed PQD/OSC PHJs are reported. The phototransistors based on bilayer PQD/PDVT‐10 PHJs show responsivity up to 1.64 × 10 4 A W −1 , specific detectivity of 3.17 × 10 12 Jones, and photosensitivity of 5.33 × 10 6 when illuminated by 450 nm light. Such high photodetection performance is attributed to efficient charge dissociation and transport, as well as the photogating effect in the PHJs. Furthermore, the tri‐layer PDVT‐10/PQD/Y6 PHJs are used to construct photodiodes working in self‐powered mode, which exhibit broad range photoresponse from ultraviolet to near‐infrared, with responsivity approaching 10 −1 A W −1 and detectivity over 10 6 Jones. These results present a convenient and scalable production processes for solution‐processed PHJs and show their great potential for optoelectronic applications.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Development and Prospects of Halide Perovskite Single Crystal Films

Halide perovskite single crystal (HPSC) films have demonstrated extraordinary performance in solar cells, photodetectors, and lighting applications, owing to the high carrier mobility, long carrier diffusion length, tunable bandgap, and large light absorption coefficients of these materials. Here, the recent development of the major HPSC thin films is reviewed systematically, including MAPbI 3 , α-FAPbI 3 , MAPbBr 3 , CsPbBr 3 , with special emphasis on different classes of fabrication methods and thin-film characteristics. So finally, the conclusion and prospects in this field are discussed in detail. It is anticipated that the HPSC thin films will lead to a compelling future for the rising electronic applications.

MAPbI3↗
DOE OSTI2023

Using 3D position sensitivity to reveal response non-uniformities in CdZnTe, TlBr, and CsPbBr 3 detectors

Position sensitivity enables the correction of response non-uniformities in room-temperature semiconductor detectors caused by crystal defects and other factors. It can also be used to pinpoint the exact location of crystal defects responsible for the response variations. This work describes a technique for revealing and visualizing the detector regions affecting the charge collection efficiency in CdZnTe (CZT), TlBr, and CsPbBr 3 detectors configured as position-sensitive virtual Frisch-grid (VFG) devices. The technique correlates the photopeak events in energy spectra with their spatial distributions inside the detectors using the position information. By selecting the events from narrow energy intervals within a photopeak, we can visualize the detector volumes with particular charge collection efficiencies, which, in turn, correlate with the locations of electrode and crystal defects. Here, we demonstrate this technique in several examples. Columnar structures in the volume plots (position distribution maps) are consistent with signal losses near or at the anode in selected samples of CZT and TlBr. Structures exhibiting a distinct depth dependence are consistent with grain boundaries or other crystal defects.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗
DOE OSTI2025

X-ray escape peaks in gamma-ray spectrum acquired by perovskite detector

The X-ray escape peaks are clearly visible in the high-resolution gamma spectra acquired by CsPbBr 3 , credit to the rapidly improving energy resolution of perovskite gamma detectors. But it also raises concerns. If this peak remains as significant as it is, perovskite gamma detectors would have very limited use in complex gamma spectrometry applications. This paper discusses the origin of the escape peaks in CsPbBr 3 detectors, benchmarked against Ge and CZT detectors. The Pb escape peak consists of four escape peaks that are merged together, while the Cs and Br escape peaks are hidden inside the photopeak of 137 Cs (662 keV). These combined effects either create a noticeable gamma peak observed to the left of the 662 keV photopeak when acquired using a high-resolution CsPbBr 3 detector or raise the left slope of the photopeak. We also explore potential methods to mitigate these peaks, such as applying anti-coincidence method. The height of the escape peaks diminishes as the detector volume increases but will not go away entirely. The relationship between the observed Pb escape peak and the detector's dimensions is demonstrated through Monte Carlo simulation.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2024

Growth of High-Purity CsPbBr 3 Crystals for Enhanced Gamma-Ray Detection

High-quality CsPbBr 3 crystals hold significant potential for gamma-ray detection due to their remarkable optoelectronic properties. This study details an optimized production process using the Bridgman method to achieve highly pure CsPbBr 3 crystals. By implementing rigorous synthesis and purification techniques, we successfully reduced the total impurity levels to 9 ppm, as confirmed by glow discharge mass spectroscopy (GDMS). The resulting CsPbBr 3 crystals demonstrate exceptional performance, including high transparency, intense photoemission, and prolonged photoluminescence decay times. These properties facilitate superior gamma-ray detection with an energy resolution of 1.4% for the 137 Cs 662 keV gamma-rays, comparable to commercial Cd 1-x Zn x Te (CZT) detectors. Our findings underscore the critical relationship between material purity and detector performance, highlighting the potential of CsPbBr 3 as a cost-effective alternative in radiation detection applications. Further studies on defect origins and electronic states are necessary to fully leverage the capabilities of CsPbBr 3 crystals in practical high-energy radiation detection systems.

Bridgman↗
DOE OSTI2024

Intraband Cooling and Auger Recombination in Weakly to Strongly Quantum-Confined CsPbBr 3 Perovskite Nanocrystals

Semiconductor nanocrystals (NCs) with size-tuned energy gaps present unique and desirable properties for optoelectronic applications. Recent synthetic advancements offer routes to spheroidal CsPbBr 3 perovskite NCs in the strong quantum confinement regime with narrow size dispersion. Further, using tunable femtosecond laser pulses, we examine intraband carrier relaxation using transient absorption spectroscopy and show that, across the transition from weak to strong confinement, hot carrier lifetime increases compared to larger bulk-like particles. However, further increases of confinement subsequently lead to a reduction of the hot carrier lifetime and increase of the non-radiative Auger recombination rate. Finally, we show that hot carrier lifetimes increase as a function of excess energy above the band gap less sensitively under high confinement in comparison to the bulk. Understanding such unique trends is important for maximizing hot carrier lifetimes for use in next-generation hot carrier devices as well as evaluating the transition from weak to strong confinement.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Dependence of Exciton Spin Dynamics on Quantum Confinement Dimensionality in CsPbBr 3 Nanocrystals

Semiconductor nanomaterials offer a promising platform to produce optically addressable spins for use in quantum technologies. Here, in this study, we examine CsPbBr 3 nanospheres, cubes, and rods spanning the zero-dimensional (0D) to three-dimensional (3D) transition to investigate the influence of dimensionality and shape on exciton spin decoherence. Using circularly polarized transient absorption spectroscopy, we find that the spin relaxation rate is independent of the surface to volume ratio and instead follows a dependence on the length of the shortest dimension. Additionally, differences in surface quality and termination appear to have no effect on the spin relaxation rate for measured materials, and instead the spin relaxation rate is most clearly correlated with the exciton binding energy. Finally, decreasing the dimensionality of the nanomaterials decreases the influence of multiexciton interactions on the spin relaxation rate.

CsPbBr3 nanocrystals↗
DOE OSTI2025

Assessment of Blocking Contacts in Suppressing Polarization Effects in CsPbBr 3 Perovskite Detectors

The CsPbBr 3 perovskite has garnered significant attention as a room-temperature semiconductor for hard radiation detection due to straightforward synthesis, scalable crystal growth, low cost, and excellent energy resolution. However, despite these advantages, at ambient temperature, CsPbBr 3 devices may experience performance deterioration and irreversible failure due to “polarization” induced by electromigration of ions to electrical connections on the device. In this study, we tested several contact materials and their optimization deposition techniques to assess the stability of high-performance CsPbBr 3 γ-ray detectors. Metals, with low work functions (Ti, In, Sn, Sb, Pb, Bi, Al, Au, and TiC) and high-work-function (Au or Pt) contacts, were used to form different Schottky junctions using vacuum thermal evaporation, electron-beam evaporation, and sputtering methods. These detectors were tested in intermittent and continuous modes to assess their stability. Among the tested detectors, the Bi/CLB/Pt electrode configuration demonstrated superior stability, operating effectively for 11 months under periodic testing and 16 days under continuous testing. In contrast, other configurations functioned only for a few months under intermittent conditions. Upon incorporating a ~40-nm-thick TiC passivation layer on the anode side (Bi/TiC/CLB/Pt), the CLB device operated continuously for 36 days without degradation. In many cases, the failure mode of the devices was due to the degradation of the anode. Here, the chemical changes in the fresh and deteriorated anodes were characterized using scanning electron microscopy and energydispersive X-ray spectroscopy

CsPbBr3 perovskite↗
DOE OSTI2025

Interplay Between Metastability and Mechanically Induced Structural Instability in CsPbBr 3 Photovoltaic Perovskite

An atomic-level understanding of the underlying structural metastability is still absent in halide perovskite photovoltaic systems. Focusing on the model material CsPbBr 3 , the impact of mechanically induced atomic structure alteration is elucidated through structural modeling and X-ray diffraction measurements. Sudden Cs–Br bond breaking drives the system metastability, where the first-order transition arises from cation-halide bond strain relief by severing the corner connectivity of the PbBr 6 units. The pressure–volume and entropy terms govern the Gibbs free-energy landscape in halide perovskites. In conclusion, metastability is revealed as a critical factor limiting the performance of lead halide perovskites under extreme but natural environments.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Investigating the Role π -Rich Solvents Play in the Growth of Cesium Lead Bromide Nanocrystals

In this report, the role that a high-boiling-point solvent type plays on the nucleation and growth, morphology, and crystal-phase transformation of cesium lead bromide nanocrystals (CsPbBr 3 ) is studied. The CsPbBr 3 products were compared between a one-pot growth mechanism at room temperature (RT) versus a hot-injection mechanism (HI) control using dibenzyl ether (DBE), diphenyl ether (DPE), dioctyl ether (DOE), or 1- octadecene (ODE). The coordination between these solvents and the PbBr 2 salt precursors resulted in different plumbate [PbSBr n ] 2−n precursors being formed. The S-to-Pb 2+ coordination within [PbSBr n ] 2−n was probed by UV−vis and solvent-phase 207 Pb NMR, both of which showed considerable coordination between [PbSBr n ] 2−n and the π-rich DBE and DPE, whose reactivity affected CsPbBr 3 growth. The effect was more pronounced for CsPbBr 3 prepared via RT, where the morphology was tunable, with π-rich solvents producing thin rod-like CsPbB r3 with a blue emission, compared to the green-emitting thicker platelets formed via HI. While XRD showed crystalline products for both RT and HI, with orthorhombic and cubic forms, respectively, the RT products had considerable surface defects, as was indicated by lower quantum yields, and to understand this the photoluminescent lifetimes were measured by time-correlated single photon counting.

207Pb NMR↗
DOE OSTI2024

Unraveling the Luminescence Quenching Mechanism in Strong and Weak Quantum-Confined CsPbBr 3 Triggered by Triarylamine-Based Hole Transport Layers

Luminescence quenching by hole transport layers (HTLs) is one of the major issues in developing efficient perovskite light-emitting diodes (PeLEDs), particularly prominent in blue-emitting devices. While a variety of material systems have been used as interfacial layers, the origin of such quenching and the type of interactions between perovskites and HTLs are still ambiguous. Here, we present a systematic investigation of the luminescence quenching of CsPbBr 3 by a commonly employed hole transport polymer, Poly(9,9-dioctylfluorene-alt-N-(4-sec-butylphenyl)-diphenylamine) (TFB) in LEDs. Strong and weakly quantum-confined CsPbBr 3 (nanoplatelets (NPLs)/nanocrystals (NCs)) are rationally selected to study the quenching mechanism by considering the differences in their morphology, energy level alignments, and quantum confinement. The steady-state and time-resolved Stern-Volmer plots unravel the dominance of dynamic and static quenching at lower and higher concentrations of TFB, respectively, with maximum quenching efficiency of 98%. The quenching rate in NCs is faster than in NPLs owing to their longer PL lifetimes and weak quantum confinement. The ultrafast transient absorption results support these dynamics and rule out the involvement of Forster or Dexter energy transfer. Finally, the 1D 1 H and 2D NOESY NMR study confirms the exchange of native ligands at the NCs surface with TFB, leading to dark CsPbBr 3 -TFB ensemble formation accountable for luminescence quenching. This highlights the critical role of the triarylamine functional group on TFB (also the backbone of many HTLs) in the quenching process. These results shed light on the underlying reasons for the luminescence quenching in PeLEDs and will help to choose the interfacial layers rationally for developing efficient LEDs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Low-energy pathways lead to self-healing defects in CsPbBr 3

Self-regulation of free charge carriers in perovskites via Schottky defect formation has been posited as the origin of the well-known defect-tolerance of metal halide perovskite materials. Understanding the mechanisms of self-regulation promises to lead to the fabrication of better performing solar cell materials with higher efficiencies. We investigate many such mechanisms here for CsPbBr 3 , a popular representative of a more commercially viable all-inorganic metal halide perovskite. We investigate different atomic-level mechanisms and pathways of the diffusion and recombination of neutral and charged interstitials and vacancies (Schottky pairs) in CsPbBr 3 . We use nudged elastic band calculations and ab initio-derived pseudopotentials within quantum ESPRESSO to determine energies of formation and migration and hence the activation energies for these defects. While halide vacancies are known to exhibit low formation energies, the migration of interstitials is less studied. Our calculations uncover interstitial defect pathways capable of producing an activation energy at, or below, the single experimental value of 0.53 eV observed for the slow, temperature-dependent recovery of light-induced conductivity in bulk CsPbBr 3 . Our work reveals the existence of a low-energy diffusion pathway involving a concerted “domino effect” of interstitials, with the net result that interstitials can diffuse more readily over longer distances than expected. This observation suggests that defect self-healing can be promoted if the “domino effect” strategy can be engaged.

14 SOLAR ENERGY↗
DOE OSTI2022

Giant spin-selective bandgap renormalization in CsPbBr 3 colloidal nanocrystals

The spin-dependence of the strongly correlated phenomena and many-body interactions play an important role in quantum information science. In particular, it is quite interesting but unclear how the spin degree of freedom ramifies the bandgap renormalization, one of the fundamental many-body phenomena. We report the first room-temperature observation of giant spin-selective bandgap renormalization (SS-BGR) in CsPbBr 3 colloidal nanocrystals using time-resolved circularly polarized femtosecond pump-probe spectroscopy. The SS-BGR results from many-body interactions among carriers with the same spin that renormalize their joint density of states by 57+/- 1 meV, visualized here as photoinduced absorption (PIA) below band-edge transition energy when the pump and probe are co-polarized. The hallmark result of spectrally resolved SS-BGR is in stark contrast to the usually submerged signal in II-VI and III-V semiconductors and is 3 orders of magnitude larger than that observed in Ge/SiGe quantum wells, highlighting the unique and beneficial band structure of the metal-halide semiconductors. We propose that the PIA, due to SS-BGR, can be used to describe the spin-polarization and spin-relaxation dynamics. The experimental and theoretical findings open up new possibilities for optical manipulation of spin degrees of freedom and their many-body interactions in metal-halide perovskite nanocrystals for potential room-temperature applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗