Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “textured surfaces”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

In situ x-ray studies of the incipient ZnO atomic layer deposition on In 0.53 Ga 0.47 As

We describe in detail how ZnO films grow on In 0.53 Ga 0.47 As substrates by atomic layer deposition (ALD), employing a suite of in situ synchrotron x-ray techniques. Combining results from different measurements allows the distinguishment of three different growth behaviors: an initial, slow linear growth, often referred to as a growth delay (regime I), followed by a nonlinear growth (regime II), and finally, a steady, linear growth (regime III), the last of which is the self-limited growth behavior characteristic of ALD. By the end of regime I, the In 0.53 Ga 0.47 As surface is covered with an ultrathin, poorly ordered Zn oxide layer. The transition from regime I to II is clearly evidenced by the appearance in the x-ray absorption spectra of characteristic features of the wurtzite structure, as well as the nucleation and growth of ZnO grains (three-dimensional) on top of the poorly ordered Zn oxide layer. Regime II ends when the growth per cycle reaches a constant level. We show that the water pressure during growth has an impact on the duration of the growth delay (regime I), unlike the substrate temperature. In the regime of steady growth, we observe that the rate of deposition obtained for all temperatures inside the ALD window is 0.17 nm cy(-1). The deposition temperature has clear effects on the film texture and initial crystallization behavior, as well as the final crystallinity and thicknesses of the layers adjacent to the In 0.53 Ga 0.47 As substrate. Based on the experimental results and earlier ab initio calculations and Monte Carlo simulations of ZnO ALD on ZnO, we suggest reaction mechanisms consistent with our findings, and we present a model of growth starting from the very earliest stages of deposition to the steady growth regime.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Strong correlations and orbital texture in single-layer 1T-TaSe2

© 2020, The Author(s), under exclusive licence to Springer Nature Limited. Strong electron correlation can induce Mott insulating behaviour and produce intriguing states of matter such as unconventional superconductivity and quantum spin liquids. Recent advances in van der Waals material synthesis enable the exploration of Mott systems in the two-dimensional limit. Here we report characterization of the local electronic properties of single- and few-layer 1T-TaSe2 via spatial- and momentum-resolved spectroscopy involving scanning tunnelling microscopy and angle-resolved photoemission. Our results indicate that electron correlation induces a robust Mott insulator state in single-layer 1T-TaSe2 that is accompanied by unusual orbital texture. Interlayer coupling weakens the insulating phase, as shown by reduction of the energy gap and quenching of the correlation-driven orbital texture in bilayer and trilayer 1T-TaSe2. This establishes single-layer 1T-TaSe2 as a useful platform for investigating strong correlation physics in two dimensions.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Epitaxial growth of hexagonal BaNi O 3–δ thin films on SrTi O 3 (111) substrates

Transition metal oxides containing nickel species in oxidation states higher than 3+ often exhibit high catalytic activity, which makes them promising for applications as advanced electrocatalysts for water splitting and fuel cells. Here, we examine the structure and properties of BaNiO 3 (BNO) thin films, containing formally Ni 4+ , grown on SrTiO 3 (111) substrates using oxygen-plasma–assisted molecular beam epitaxy. X-ray diffraction and scanning transmission electron microscopy measurements reveal that BNO films have a hexagonal structure with $c$- and $a$-axes of mixed textures showing epitaxial relationships BNO (0001) ∥ SrTiO 3 (111) and BNO (10$\overline{1}$0) ∥ SrTi O 3 (111), respectively. The formation of the $a$-axis texture is dominant due to the smaller lattice mismatch with the substrate. Here, density functional theory calculations confirm that the hexagonal BNO film with the $a$-axis texture is energetically more favorable than the competing $c$-axis texture. Detailed spectroscopy data analysis indicates that hexagonal BNO films contain mixtures of Ni 2+ , Ni 3+ , and Ni 4+ species, with Ni 4+ being dominant. Our study provides insights into stabilizing Ni 4+ in complex oxides, which is important for further exploration of the potential of materials containing Ni 4+ .

36 MATERIALS SCIENCE↗
DOE OSTI2023

Laboratory-Scale Coal-Derived Graphene Process (Final Report)

The Energy & Environmental Research Center (EERC) conducted a laboratory-scale coal-derived graphene (CDG) project focused on developing a technological process for making graphene from four U.S. domestic coal or coal wastes, including lignite from North Dakota, subbituminous coal from Wyoming, bituminous coal from Utah, and anthracite from Pennsylvania. The project was divided into two performance or budget periods (BPs), with BP1 comprising the up-front laboratory experiments to make graphene materials from coal beginning on May 1, 2020, to April 30, 2022. BP2 was conducted from May 1, 2022, to April 30, 2023, and was focused on analyzing the CDG process economic feasibility and the technical gaps for technological scale-up and commercialization. During this project, a few different coal-derived high-value products have been demonstrated, including graphite, graphene oxide (GO), reduced graphene oxide (rGO), and graphene quantum dots (GQDs). A new graphite microstructure was discovered and named “croissant graphite” because of the exterior morphological and textural resemblance to croissant food items sold in commercial groceries stores. The new graphite structure and the associated preparation from coal or coal waste feedstocks has been the subject of a U.S. patent application. The systematic experimental processes involving coal cleaning, upgrading, and conversion to high-value carbon products culminated into a developed upgraded coal-to-products (UCP) technology that is being pursued for potential fast-track commercialization, if funding is available. It is envisioned that commercialization of the UCP technology would increase consumption of U.S. domestic coals or coal wastes to make environmentally sustainable high-value products for the electronics industry, high-energy-storage applications, and clean energy technologies such as electric vehicle (EV) lithium-ion batteries (LIBs), for which graphite has become a critical mineral commodity. Croissant graphite microstructures, when observed by field emission scanning electron microscopy (FESEM), display wavy surface morphology and often grow from a base that is made of graphitized particles with honeycomb-like layers, which are believed to be graphene layers. While more studies are needed to fully ascertain the mechanisms of the croissant graphite microstructure formation, it is postulated that their growth may begin from curling of the graphene sheets into ribbon-like structures, and continuous growth and densification of the ribbon-like structures forms croissant microstructures. Additional studies are ongoing to evaluate the electrochemical performance of croissant graphite for LIB applications and to determine the experimental conditions necessary to tune on/off croissant formation so that it can be either optimized or suppressed depending on performance evaluation results. In addition to the discovery of croissant graphite, the graphitization process from the four coal ranks in general was successful. X-ray diffraction (XRD) analysis showed that the degree of graphitization (DoG) ranged from 12% to 80% in an early sample set, and further optimization on lignite coal produces a DoG of about 92%, which was spectacular to see as lignite is the lowest-rank coal. Thus, it is expected that the graphitization performance for higher-rank coals will be similar or better when optimized as well. The coal-derived graphite was used to make GO and rGO. Analytical characterization, e.g., by methods such as Raman spectroscopy, XRD, Fourier transform infrared (FTIR) spectroscopy and FESEM, showed that the sequence of converting the coal to graphite, exfoliating it to GO, and then chemically reducing the GO to rGO was successful. Although coal naturally contains aromatic compounds and some relatively small-sized condensed aromatic units, it does not contain graphene sheets. In the UCP process, the aromatic domains in the coals, particularly low-rank coals, are concentrated and condensed further into graphene sheets, which are ordered into a 3D stack during graphitization. The synthesized graphite is then unpacked by methods such as exfoliation to various graphene products. GQDs were synthesized from all four coal types, and their optical properties were demonstrated to be tunable by the coal precursor preprocessing treatments. In all four coal types, enhanced optical properties were observed for the produced GDQs with incremental improvements made to the coal precursors. GQDs produced from raw coal samples displayed lower ultraviolet–visible (UV–Vis) spectroscopy absorbance intensity compared to those obtained from cleaned and upgraded coal residues. The photoluminescence (PL) intensities also varied with pretreatment conditions and with the concentration of GQDs in aqueous solutions. GQDs obtained from anthracite show longer emission wavelengths and can be excited by visible light as opposed to GQDs derived from the other coal ranks. UV fluorescence 3D maps and spectra revealed that the emission wavelength at which the GQDs solutions display the highest intensity was slightly redshifted based on the coal precursor pretreatments. In low-rank coal (lignite and subbituminous) samples, two clusters were observed in the maps for GQDs, which may suggest that there are potentially two types of fluorophores in solution or two main size populations. The ability to tune the properties of GQDs based on processing methods can be exploited to make GQDs for various optical display or optoelectronics applications. The results also highlight the importance of removing coal-borne impurities to improve the quality of the coal precursor for preparation of graphene products. Coal and/or coal wastes preprocessing methods were developed and applied to clean and upgrade the coal precursors prior to graphitization and subsequent conversion to graphene products. The preprocessing methods involve high specific-gravity separations, mineral acid cleaning (no hydrofluoric acid), and subsequent upgrading by reducing the coal-borne heteroatom (nitrogen, sulfur, and oxygen) content using proprietary chemical agents. Analytical characterization revealed that the preprocessing steps were successful, with ash reductions that range from 38% to 80% and residual ash content that was below the 5 wt% initial target. Based on proximate and ultimate analysis, the heteroatom reduction reactions produced upgraded coal residues with the oxygen content reduced by 8% to 24%, with additional reductions in the nitrogen and sulfur contents. An initial assessment of the waste streams from the UCP process shows very small to negligible environmental impact due to CO 2 , NO x , and SO x because most process steps are performed under inert atmosphere with argon. Consequently, reactive oxygen environments that tend to create these species are avoided. The inorganic and potentially hazardous species are released into aqueous waste streams that are easy to handle for proper disposal. The liquid waste streams were found to contain low-level concentrations of rare-earth elements (REEs), which could be concentrated and recovered as value-added by-products. Additionally, the volatile and gaseous fractions from carbonization and heat treatment contain useful organic compounds that can also be recovered as potential valuable by-products. Thus, the UCP technology is considered an environmentally sustainable and promising emerging technology for making high-value products from coal and coal wastes, with potential additional value-added by-products. Analysis of potential markets for the coal-derived carbon products shows a strong demand in both niche market sectors and across a wide variety of other industrial sectors. Graphite is currently considered a critical mineral commodity that has a large and growing demand in the LIB industry for EV applications. Based on data from Fortune Business Insights (2022) and Marketwatch (2023) reports, the average global graphite market is projected to reach about 33 billion by 2028, growing at a compound annual growth rate (CAGR) of about 7%, with much of this growth expected to be in the LIB industry. GO and rGO have strong market potentials in various application areas, such as coatings for anticorrosion, anti-icing, and antimicrobial protection, thermal barriers, wear resistance, sensors, additive manufacturing such as 3D inks, and others. GQDs are the emerging key player in the bioimaging, photovoltaics, and light-emitting diodes (LEDs) applications, with the potential to replace traditional semiconductor quantum dots (SQDs), which are based on metallic systems that are more toxic and more expensive. Biomedical applications of GQDs are becoming more attractive because of low to no toxicity and extremely low cost compared to SQDs. The major challenges for scale-up and commercialization of coal-derived carbon products such as graphene vary from the inherent attributes of graphene itself to reluctance to accept graphene in new manufacturing processes because of the uncertainty of the unknown. The 2D nature of graphene materials with a thickness of one atom presents significant challenges to proper handling/processing, and process scale-up becomes difficult because it requires high-end, expensive equipment, even for routine handling and analysis for quality assurance and control. Pristine graphene can also be extremely difficult to work into other matrices, thus hindering downstream processibility, especially at large scale. Currently, the cost of graphene and graphene products is still high and presents an economic risk that tends to slow down investment in scaling up emerging technologies. The lack of a standard for graphene materials for quality assurance and quality control poses a great challenge not only for the markets but also for commercialization efforts. A first-look economic feasibility analysis of the UCP technology provided valuable information that suggests the UCP process would be feasible, especially when it is scaled to a pilot scale and could be more competitive at the full scale. Graphitization was found to be the most energy-consuming and most capital-intensive step in the overall process. In small laboratory- and bench-scale experiments, labor is a significant contributor to the total process costs. Although these energy, capital, and labor constraints contribute to a higher selling price for the product, a preliminary economic model suggests that the process would be feasible at large scale when the process is fully integrated, optimized, and automated.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2020

Modeling Time-Dependent Surrogates of Additive-Manufactured Nuclear Fuels Processes

Additive manufacturing (AM) technology is being increasingly adopted in a wide variety of application areas for its ability to rapidly produce, prototype, and customize designs. Recently, a hybrid AM technique was successfully developed at Idaho National Laboratory (INL) to manufacture nuclear fuels [1]. Despite the advantages, this AM technique needs optimization due to defects from a highly complex melting and sintering process. The complex metallurgical phenomena during AM processes are strongly related to parameters such as applied laser power, traveling speed, and scan style, which could lead to differences in density, residual stress, crystallographic texture, and mechanical properties. In addition, stochastic variations in laser energy interaction and associated multiscale/multiphysics phenomena cause variations in microstructure evolution and mechanical properties. Currently, researchers at INL are focusing on developing a comprehensive modeling framework, leveraging INL’s simulation tools MOOSE/MARMOT/BISON/RAVEN [2-4] to describe all steps of this AM process across multiple length scales. Although this advanced framework plays a critical role in enabling enhancements to traditional trial and error approaches for design and optimization of nuclear fuel materials, it remains computationally intense, limiting its use in sensitivity and optimization analysis. In this case, an accurate and inexpensive surrogate becomes an effective tool for providing a tractable approximation of the underlying underline physics. Surrogate models generally not based on the physics of a system are purely mathematical models used to capture the relationships between specific system inputs and outputs. Popular approaches, including neural networks [5], response surfaces [6], and subspace-based reduced order models [7], have been applied to a wide range of disciplines, such as nuclear reactor design, aerospace design and automotive design. In this summary, we employ advanced time-dependent surrogate models such as high-dimensional model representation (HDMR) [8] and physics-informed deep neural network (PINNs) [9] to accelerate the design and optimization of AM process.

42 ENGINEERING↗
DOE OSTI2022

Electrical Analysis of Pulsed Laser Annealed Poly-Si:Ga/SiOx Passivating Contacts

High-efficiency single crystalline silicon (c-Si) solar cells require precise control of dopant diffusion profiles and highly active doping concentrations through thermal annealing. Conventional furnace annealing has been successfully employed for dopant diffusion in aluminum back-surface field (Al-BSF), passivated emitter and rear contact (PERC), and Topcon cells. However, furnace annealing limits some next-generation polycrystalline silicon (poly-Si) on SiOx passivating contacts. This limitation largely affects p-type passivating contacts by not being able to: 1) control the dopant diffusion accurately to prevent B segregation at the SiOx and c-Si interface; and 2) provide highly activated doping concentrations for low contact resistivity. In this contribution, we use a nanosecond excimer laser to examine the passivation quality and electrical performance of both B- and Ga-doped poly-Si/SiOx passivating contacts. The core of this method is to take advantage of the nonequilibrium nature of the anneal through rapid melting and recrystallizing the poly-Si in a short timescale and to achieve doping concentrations above the solid solubility limit. Simulations were performed on polished surfaces to visualize the doping diffusion profiles under different laser conditions, and secondary ion mass spectrometry (SIMS) was used to verify the experimental diffusion profiles post pulsed laser melting (PLM). The results show the dopant diffusion profiles can be tuned precisely through PLM. The electrical analysis using VdP-Hall measurements reveals that the active doping concentration reached 10^21 cm-3 for B and ~2×10^21 cm-3 for Ga in poly-Si, far exceeding their solid solubility limit in Si, with a nearly 100% dopant activation achieved for B, and 20% for Ga. This highly activated dopant profile results in a low contact resistivity of <15 mO·cm^2 for B-doped contacts and <40 mO·cm^2 for Ga-doped contacts. We demonstrate that the passivation quality of the laser annealed contacts shows a linear dependency with the laser energy density and the number of pulses. PLM was also performed on random pyramid textured samples, and we found that preferential melting exists for the tips of pyramids, which can be pursued further for selective pinhole opening. Additionally, we perform thermal stability tests of these hyperdoped passivating contacts and show that under certain laser conditions, the B-doped samples exhibit good thermal stability with near full activation for temperatures up to 800°C. Lastly, we transfer this technique to a larger area by overlapping laser spots and show uniform passivation quality and electrical performance. We are currently implementing this PLM annealed p-type passivating contacts into double-side back-junction poly-Si/SiOx passivating contact devices. Our results show that PLM can not only enable the next generation of high-efficiency c-Si photovoltaics technology but can also benefit the c-Si integrated circuit industry through hyperdoping other semiconductors with atoms that may otherwise have a low solubility.

doping diffusion profile↗
DOE OSTI2020

Fine Root and Soil Organic Carbon Depth Distributions are Inversely Related Across Fertility and Rainfall Gradients in Lowland Tropical Forests

Humid tropical forests contain some of the largest soil organic carbon (SOC) stocks on Earth. Much of this SOC is in subsoil, yet variation in the distribution of SOC through the soil profile remains poorly characterized across tropical forests. We used a correlative approach to quantify relationships among depth distributions of SOC, fine root biomass, nutrients and texture to 1 m depths across 43 lowland tropical forests in Panama. The sites span rainfall and soil fertility gradients, and these are largely uncorrelated for these sites. We used fitted b parameters to characterize depth distributions, where b is a numerical index based on an asymptotic relationship, such that larger b values indicate greater concentrations of root biomass or SOC at depth in the profile. Root b values ranged from 0.82 to 0.95 and were best predicted by soil pH and extractable potassium (K) stocks. For example, the three most acidic (pH < 4) and Kpoor (< 20 g K m -2 ) soils contained 76 ± 5% of fine root biomass from 0 to 10 cm depth, while the three least acidic (pH > 6.0) and most K-rich (> 50 g K m -2 ) soils contained only 41 ± 9% of fine root biomass at this depth. Root b and SOC b values were inversely related, such that a large fine root biomass in surface soils corresponded to large SOC stocks in subsoils (50–100 cm). SOC b values were best predicted by soil pH and base cation stocks, with the three most base-poor soils containing 34 ± 8% of SOC from 50 to 100 cm depth, and the three most base-rich soils containing just 9 ± 2% of SOC at this depth. Nutrient depth distributions were not related to Root b or SOC b values. Here, these data show that large surface root biomass stocks are associated with large subsoil C stocks in strongly weathered tropical soils. Further studies are required to evaluate why this occurs, and whether changes in surface root biomass, as may occur with global change, could in turn influence SOC storage in tropical forest subsoils.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

High-Performance Passivating Contacts for Si PV Based on Engineered, Doped Nanopinholes through Dielectric Layers

We present a novel, industrially relevant method to fabricate high-performance poly-Si passivating contacts for Si PV. Passivating contacts based on SiOx/poly-Si layer stacks have been implemented in record-efficiency homojunction Si solar cells. In this technology, the carrier transport through a surface-passivating SiOx is enabled either by quantum-tunneling or nanopinholes. The doped poly-Si layer provides charge-carrier selectivity. Previously, the ISFH research group demonstrated a record 26.1% efficient Si homojunction cell, where transport pinholes in ~2 nm SiOx were produced by thermal breakdown at > 1000 degrees C, which is hard to control and is surface morphology-dependent. At room temperature, our new process uses electroless plating of Ag nanoparticles, followed by metal-assisted chemical etching. Nanogalvanic corrosion yields < 20 nm-wide nanopinholes in an insulating > 2 nm SiOx layer. The nanopinholes are filled by a heavily doped a-Si:H overlayer. We drive in the dopants into the Si wafer with subsequent high-temperature annealing. Preferential incorporation of dopants at pinhole locations results in nanoscale p+/n or n+/n junctions near the wafer interface. Each heavily-doped nanoscale pinhole junction collects and transports photogenerated carriers to the cell metal contacts. The density of the engineered nanopinholes can be tuned over a wide range which is critical for optimization of device performance. The same nanogalvanic corrosion principles can be applied to produce doped transport pinholes in well-passivating thick dielectric SiOx/SiNy stacks. Importantly, our process does not rely on thermal breakdown of the dielectric layers and can be applied to textured wafers resulting in Si solar cells with > 20% conversion efficiency.

dielectric layer↗
DOE OSTI2020

Influence of Binder Coverage on Interfacial Chemistry of Thin Film LiNi 0.6 Mn 0.2 Co 0.2 O 2 Cathodes

In this work, we explore the influence of binder coverage and chemistry on the interfacial properties of the textured Ni-rich cathode LiNi 0.6 Mn 0.2 Co 0.2 O 2 . We find that the formation of the cathode/electrolyte interphase (CEI) composition varies significantly for cathodes coated with either poly(vinylene fluoride) (PVDF), carboxymethyl cellulose (CMC), or lithium polyacrylate (LiPAA) after cycling to high upper cutoff voltages (4.5 V vs Li/Li). The PVDF-coated samples had a thinner CEI and twice the relative concentration of LiF and Li 2 CO 3 to Li x PO y F z species in the CEI compared to the uncoated sample. This correlated with significantly lower interfacial impedance (285 vs ~1700 Ohm-cm 2 ) and improved capacity retention between cycles of the PVDF-coated samples compared to the other binder compositions and the uncoated sample. CMC-coated samples performed worst, with a CEI comprised of greater amounts of Li x PO y F z . In addition, we find the choice of binder results in the selective protection or promotion of electrolyte reactions at the (104) surface of the 622 cathode. This suggests that the choice of binder can impact the surface chemistry and performance of high voltage cathodes and supports an avenue for interest in multifunctional binders for stabilizing the CEI.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Soft matter approach for creating novel protein hydrogels using fractal whey protein assemblies as building blocks

In this study, mesoscopic sized fractal assembly (FA) particles were prepared using whey protein isolate; the coldset gelation properties of FA particles were investigated in-depth. Two types of FA particles (FA -62 and FA -90) with different mean sizes were synthesized through controlled thermal treatment of whey protein solutions at two concentrations (62 g/L and 90 g/L). Particle characteristics e.g. hydrodynamic radius, ζ-potential and surface hydrophobicity were dependent on pH and structure of FA. Transmission electron microscopy (TEM) observation confirmed the fractal morphology and small-angle X-ray scattering (SAXS) analysis suggested an internal fractal structure for the obtained FA particles. Eight cold-set FA protein gels (2 % w/v) were manufactured by controlling two gelling factors at two levels: pH (5.8 and 7.0) and Ca 2+ content (5 mM and 10 mM). Rheological characteristics in the large amplitude oscillatory shear regime revealed that pH 7.0 gels were softer and elastic while pH 5.8 gels were harder and brittle. Rheology Pipkin diagrams demonstrated that the strain softening/stiffening and the shear-thinning/thickening behaviors may be fine-tuned by manipulating the key gelation factors: e.g. FA structure, pH, and Ca 2+ . The entrainment speed-dependent friction coefficient curves showed that at an intermediate velocity regime (6-250 mm s -1 ), FA -90 particles induced hydrogels had superior lubrication effect compared to FA -62 gels. Further, this work demonstrated a food structure design approach regarding tuning texture and lubrication properties of protein gels without changing protein content and protein composition. The optimized protein hydrogels may be used as texturizer for "cleaner label" food formulas and/or as delivery system for carrying micronutrients.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2025

Robust Spin-Moiré-Superlattice-Driven Gap Opening in EuAg 4 Sb 2 under in-Plane Magnetic Field

Moiré superlattices introduce new length and energy scales, enabling discoveries, such as unconventional superconductivity, in 2D systems. This concept has recently been extended to bulk materials with multiple-q spin textures, opening exciting opportunities for spin moiré physics. A notable example is EuAg 4 S b2 , where a spin moiré superlattice (SMS), manifested as a double-q spin modulation, induces a superzone gap opening. In this work, we investigate the tunability of this gap by an in-plane magnetic field in EuAg 4 Sb 2 by using neutron scattering, magnetization, and transport measurements. We reveal a cycloidal ground state and multiple spin-reoriented phases induced by the in-plane field, highlighting the critical role of in-plane components in driving magnetic transitions. Moreover, we demonstrate that a robust gap opening persists in the double-q phase, regardless of in-plane field orientation. Model calculations attribute this robustness to the stability of the SMS under tilted fields. Here, our results establish EuAg 4 Sb 2 as a tunable platform for exploring the spin-texture-driven superzone gap opening in electronic states.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Spontaneous Chirality Flipping in an Orthogonal Spin-Charge Ordered Topological Magnet

The asymmetric distribution of chiral objects with opposite chirality is of great fundamental interest ranging from molecular biology to particle physics. In quantum materials, chiral states can build on inversion-symmetry-breaking lattice structures or emerge from spontaneous magnetic ordering induced by competing interactions. Although the handedness of a chiral state can be changed through external fields, a spontaneous chirality flipping has yet to be discovered. We present experimental evidence of chirality flipping via changing temperature in a topological magnet EuAl 4 , which features orthogonal spin density waves (SDW) and charge density waves (CDW). Using circular dichroism of Bragg peaks in the resonant magnetic x-ray scattering, we find that the chirality of the helical SDW flips through a first-order phase transition with modified SDW wavelength. Intriguingly, we observe that the CDW couples strongly with the SDW and displays a rare commensurate-to-incommensurate transition at the chirality flipping temperature. Combining with first-principles calculations and angle-resolved photoemission spectroscopy, our results support a Fermi surface origin of the helical SDW with intertwined spin, charge, and lattice degrees of freedom in EuAl 4 . Our results reveal an unprecedented spontaneous chirality flipping and lay the groundwork for a new functional manipulation of chirality through momentum-dependent spin-charge-lattice interactions. Published by the American Physical Society 2024

3-dimensional systems↗
DOE OSTI2023

Lime slurry treatment of soils developing on abandoned coal mine spoil: Linking contaminant transport from the micrometer to pedon-scale

Historical and abandoned coal mine spoil continues to generate acid- and metal(loid)-rich porewaters and represents a geographically large and diffuse non-point source of contamination to local watersheds. A potentially inexpensive approach to treat these materials and soils developing on them is through the application of lime slurries, to neutralize acidity and encourage the (co)precipitation of metal(loids) with Fe(III)-(oxy)hydroxides, and potentially other metal-oxides and/or Ca-bearing phases. Here, the efficacy of this approach was evaluated through parallel field application and laboratory-based flow-through column experiments. The field site is Huff Run sub-watershed 25 located in Tuscarawas County, Ohio and was chosen in part because it was previously classified as one of the most highly AMD-impacted sub-watersheds in the region. Two locations with historical spoil were chosen and suction lysimeters were installed at 25 and 75 cm depth to monitor porewater composition on two sides at the base of each pile. Half of each slope received seven lime slurry treatments from June through October of 2017. A suite of aqueous (ICP-OES, IC, and TOC-L) and solid phase geochemical and mineralogical approaches (quantitative SEM-EDS and synchrotron μ-XRF) were used to determine how composition, texture, morphology, and spatial distribution of mineral coatings differ in pre- and post-lime treated soils, and how that impacts the distribution and transport of trace metal(loid)s. Mine spoil porewater at site 1 was slightly less alkaline (pH ranging from 7.04 to 7.37) than at site 2 (ranging from 7.55 to 7.71), and average electrical conductivity values at site 1 (316–405 μS cm —1 ) were slightly lower than at site 2 (358–464 μS cm —1 ), although differences between the sites were not significant. Porewater pH and electrical conductivity in all lysimeters decreased over the course of the field season but there was no obvious response to lime treatment at either site or any depth. At site 1, both treatment and depth were significant factors affecting Ca, K, Ni, SO 4 2— , and DOC concentrations while only treatment effects were significant for dissolved Al and Cu (p < 0.05). For all soils, there were no trends in metal concentration observed over time although DOC and SO 4 2— decreased over the field season. Pedon-scale changes in metal porewater concentrations in response to treatment were linked to micrometer-scale changes in mineral surface coatings; specifically, higher concentrations of Ca, Fe, Mn, and Zn were observed in the coatings and no changes were observed in Fe redox speciation, whereas total S decreased likely due to oxidation of S in coal fragments. In contrast to the field experiment, the column experiments exhibited a much greater response in effluent composition with respect to lime treatment. The untreated columns had approximately an order of magnitude more H + leached over the course of the experiment (p < 0.001) and resulted in greater Ca, Al, Cu, and DIC leached and less Mn, Zn, and SO 4 2— . Soils treated with the lime slurry in the column experiments exhibited larger and thicker secondary Fe-coatings, including the addition of Fe-sulfates. Despite clear trends in the laboratory-based column experiment where the lime-to-soil ratio was higher, the effects were either muted or undetected in the field pilot project, suggesting that a higher application rate of lime in the field is needed to achieve a similar effect. This work provides evidence that a less alkaline lime slurry could be a practical and inexpensive method of treating coal mine spoil-impacted soils and represents an important step in linking laboratory-based remediation studies to implemented field-based studies.

58 GEOSCIENCES↗
DOE OSTI2023

Defect Characterization of Monocrystalline Silicon Solar Cells with Polysilicon Passivated Contact Using Electrically-Detected Magnetic Resonance (EDMR) Spectroscopy

As the c-Si based solar cell efficiencies are approaching over 26%, it is becoming critical to characterize the low concentrations of the defects – as low as 10^10-10^11 cm-3 (for e.g., iron contamination in high-lifetime Ga-doped wafers3 and n-type wafers), and further reduce them. Also, atomistic level understanding of the mechanisms of the low concentration process-induced-defects and reliability limiting defects (such as light and elevated temperature induced degradation, surface passivation degradation) is needed to design the mitigation strategies. The conventional characterization techniques are limited due to their detection limitations. Some of the techniques based on lifetime spectroscopies can still be used for low concentration characterization however, they are based on estimations and theoretical models and hence, indirect and cannot fully reveal information about the microscopic mechanism of the defects. Thus, we present the application of an ultrasensitive magnetic resonance-based technique for the direct spectroscopic detection of the defects in Si PV - electrically detected magnetic resonance (EDMR). In this work, we aim to focus on establishing a process flow for fabrication of minicells with (miniature replica of the larger-area cells) and setting up the routine for EDMR measurements on them with the EDMR instrumentation capability at NREL. For the EDMR measurements, sample size is limited by the dimensions of sample holder tube (width less than 3.2 mm, active area - 20 mm). Thus, we have designed c-Si based minicells with polysilicon (poly-Si) passivated contacts same as the larger-area cells that we fabricate in our group at NREL. We also modified our minicell process flow for fabricating the textured minicells for preserving the texture during processing and taking care of the laser-ablation edge damage which can significantly affect the performance of such small devices. We have achieved comparable performance on these newly fabricated minicells as that of our 4 cm2 devices with same structure (comparable VOC, JSC, FF). We also conducted EDMR measurements on the minicells and observed a distinct EDMR signal at g-value ~2.005 at temperatures 30K and above, as shown in Fig. 2. We associate this signal to the presence of silicon dangling bonds based on the g-value. We also observed an EDMR signal at g-value ~1.998 at temperature ~5K. The origin of this signal is still being investigated. Thus, we show the proof of concept of minicells and EDMR measurements with which we now aim to study some of the unknown defects in silicon solar cell devices.

EDMR↗
DOE OSTI2023

2017 Meander C sediment characterization from the East River, Colorado

This dataset includes characterization data collected on sediment samples from Meander C as part of the Watershed Function Scientific Focus Area (SFA) located in the Upper Colorado River Basin. The data were collected to investigate the nature of mineral-organic associations across the meander transect and with depth. Samples were collected in 2017, and analyzed using sequential extractions (water, pyrophosphate, HCl, and dithionite) and density fractionation. Data collected include: texture, pH, root biomass, and metals (Fe, Al, Ca, Si) of bulk sediment samples; C and N of heavy fraction; and extractable OC, Fe, and Al, and organic matter characterization using high-resolution mass spectrometry (FT-ICR-MS) of sequential extractions. Sample locations are included in the ‘sample_metadata.xlsx” file. Sediment characterization data is included in the accompanying csv files: bulk and density fractions (MCB2017_density-and-bulk-fractions.csv), sequential extractions (MCB2017_sequential-extractions.csv), and FT-ICR-MS data from sequential extractions in three files to be read by the R package ftmsRanalysis (MCB2017_FTICRMS-sequential-edata.csv, MCB2017_FTICRMS-sequential-emeta.csv, and MCB2017_FTICRMS-sequential-fdata.csv). Sediment was collected in triplicate; ID’s refer to individual samples.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Data for "Soil texture and environmental conditions influence the biogeochemical responses of soils to drought and flooding"

This dataset contains data used for the paper "Soil texture and environmental conditions influence the biogeochemical responses of soils to drought and flooding". The Related References field will be updated with a full citation when available.Climate change is intensifying the global water cycle, with increased frequency of drought and flood. Water is an important driver of soil carbon dynamics, and it is crucial to understand how moisture disturbances will affect carbon availability and fluxes in soils. Here we investigate the role of water in substrate-microbe connectivity and soil carbon cycling under extreme moisture conditions. We collected soils from Alaska, Florida, and Washington USA, and incubated them under Drought and Flood conditions. Drought had a stronger effect on soil respiration, pore-water carbon, and microbial community composition than flooding. Soil response was not consistent across sites, and was influenced by site-level pedological and environmental factors. Soil texture and porosity can influence microbial access to substrates through the pore network, driving the chemical response. Further, the microbial communities are adapted to the historic stress conditions at their sites and therefore show site-specific responses to drought and flood.This dataset contains a compressed (.zip) archive of the data and R scripts used for this manuscript. The dataset includes files in .csv and .txt format, which can be accessed and processed using MS Excel or R. This archive can also be accessed on GitHub at https://github.com/kaizadp/TES_3Soils_2021 (DOI: 10.5281/zenodo.4792655).

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Experimental Observation and Spin Texture of Dirac Node Arcs in Tetradymite Topological Metals

We report the observation of a nontrivial spin texture in Dirac node arcs, i.e., novel topological objects formed when Dirac cones of massless particles extend along an open one-dimensional line in momentum space. We find that such states are present in all the compounds of the tetradymite M 2 Te 2 X family (M=Ti, Zr, or Hf and X=P or As) regardless of the weak or strong character of the topological invariant. Finally, the Dirac node arcs in tetradymites are thus the simplest possible textbook example of a type-I Dirac system with a single spin-polarized node arc.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Biochar alters hydraulic conductivity and impacts nutrient leaching in two agricultural soils

Biochar is purported to provide agricultural benefits when added to the soil, through changes in saturated hydraulic conductivity (K sat ) and increased nutrient retention through chemical or physical means. Despite increased interest and investigation, there remains uncertainty regarding the ability of biochar to deliver these agronomic benefits due to differences in biochar feedstock, production method, production temperature, and soil texture. In this project, a suite of experiments was carried out using biochars of diverse feedstocks and production temperatures, in order to determine the biochar parameters which may optimize agricultural benefits. Sorption experiments were performed with seven distinct biochars to determine sorption efficiencies for ammonium and nitrate. Only one biochar effectively retained nitrate, while all biochars bound ammonium. The three biochars with the highest binding capacities (produced from almond shell at 500 and 800 °C (AS500 and AS800) and softwood at 500 °C (SW500)) were chosen for column experiments. Biochars were amended to a sandy loam and a silt loam at 0 % and 2 % (w/w), and K sat was measured. Biochars reduced K sat in both soils by 64 %–80 %, with the exception of AS800, which increased K sat by 98 % in the silt loam. Breakthrough curves for nitrate and ammonium, as well as leachate nutrient concentration, were also measured in the sandy loam columns. All biochars significantly decreased the quantity of ammonium in the leachate, by 22 % to 78 %, and slowed its movement through the soil profile. Ammonium retention was linked to high cation exchange capacity and a high oxygen-to-carbon ratio, indicating that the primary control of ammonium retention in biochar-amended soils is the chemical affinity between biochar surfaces and ammonium. Biochars had little to no effect on the timing of nitrate release, and only SW500 decreased total quantity, by 27 % to 36 %. The ability of biochar to retain nitrate may be linked to high micropore specific surface area, suggesting a physical entrapment rather than a chemical binding. Together, this work sheds new light on the combined chemical and physical means by which biochar may alter soils to impact nutrient leaching and hydraulic conductivity for agricultural production.

54 ENVIRONMENTAL SCIENCES↗