Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ion deposition”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Magnetron sputter deposition of boron carbide in Ne and Ar plasmas

Conventional magnetron sputter deposition of B 4 C uses Ar as the working gas. In this report we explore the magnetron sputter deposition of B 4 C with a Ne plasma, which is expected to exhibit larger sputtering yields than Ar. We study properties of films deposited with different substrate tilt angles with the magnetron source operated in either direct-current (DC) or radio-frequency (RF) mode in an Ar or Ne plasma. Results show that the B 4 C film properties are determined by a combination of sputtering ballistics and effects of the working gas on the plasma discharge and gas phase scattering of depositing species flux. At constant discharge power, deposition rates for Ar and Ne plasmas are similar, which is attributed to balancing effects of a higher ballistic sputtering yield of Ne and lower ion flux to the target. Both depositing B and C neutral species and bombarding ions have higher energies for the case of Ne plasmas. Films deposited with the RF-driven Ne plasma exhibit a uniform non-columnar structure, lowest oxygen impurity content, and highest mass density and mechanical properties at a cost of Ne incorporation and larger compressive residual stress.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Impact of high-power impulse magnetron sputtering pulse width on the nucleation, crystallization, microstructure, and ferroelectric properties of hafnium oxide thin films

The impact of the high-power impulse magnetron sputtering (HiPIMS) pulse width on the crystallization, microstructure, and ferroelectric properties of undoped HfO 2 films is investigated. HfO 2 films were sputtered from a hafnium metal target in an Ar/O 2 atmosphere, varying the instantaneous power density by changing the HiPIMS pulse width with fixed time-averaged power and pulse frequency. The pulse width is shown to affect the ion-to-neutral ratio in the depositing species with the shortest pulse durations leading to the highest ion fraction. In situ x-ray diffraction measurements during crystallization demonstrate that the HiPIMS pulse width impacts nucleation and phase formation, with an intermediate pulse width of 110 μ s stabilizing the ferroelectric phase over the widest temperature range. Although the pulse width impacts the grain size with the lowest pulse width resulting in the largest grain size, the grain size does not strongly correlate with the phase content or ferroelectric behavior in these films. In conclusion, these results suggest that precise control over the energetics of the depositing species may be beneficial for forming the ferroelectric phase in this material.

36 MATERIALS SCIENCE↗
NASA NTRS1984

Deposition of diamondlike carbon films

A diamondlike carbon film is deposited in the surface of a substrate by exposing the surface to an argon ion beam containing a hydrocarbon. The current density in the ion beam is low during initial deposition of the film. Subsequent to this initial low current condition, the ion beam is increased to full power. At the same time, a second argon ion beam is directed toward the surface of the substrate. The second ion beam has an energy level much greater than that of the ion beam containing the hydrocarbon. This addition of energy to the system increases mobility of the condensing atoms and serves to remove lesser bound atoms.

Mirtich, M. J.↗
NASA NTRS1977

Optical properties of ion beam textured metals

Copper, silicon, aluminum, titanium and 316 stainless steel were textured by 1000 eV xenon ions from an 8 cm diameter electron bombardment ion source. Simultaneously sputter-deposited tantalum was used to facilitate the development of the surface microstructure. Scanning electron microscopy of the ion textured surfaces revealed two types of microstructure. Copper, silicon, and aluminum developed a cone structure with an average peak-to-peak distance ranging from 1 micron for silicon to 6 microns for aluminum. Titanium and 316 stainless steel developed a serpentine ridge structure. The average peak-to-peak distance for both of these materials was 0.5 micron. Spectral reflectance was measured using an integrating sphere and a holraum reflectometer. Total reflectance for air mass 0 and 2, solar absorptance and total emittance normalized for a 425 K black body were calculated from the reflectance measurements.

Hudson, W. R.↗
NASA NTRS1984

Status of Plasma Physics Techniques for the Deposition of Tribological Coatings

This paper reviews the plasma physics deposition techniques of sputtering and ion-plating. Their characteristics and potentials are discussed in terms of synthesis or deposition of tribological coatings. Since the glow discharge or plasma generated in the conventional sputtering and ion-plating techniques has a low ionization efficiency (<0.1%), rapid advances have been made in equipment design to further increase the ionization efficiency. The enhanced ionization favorably affects the nucleation and growth sequence of the coating. This leads to improved adherence and coherence, higher density, favorable morphological growth, and reduced internal stresses in the coatings. As a result, desirable coating characteristics can be precision tailored. Tribological coating characteristics of sputtered solid film lubricants such as MoS2, ion-plated soft gold and lead metallic films, and sputtered and ion-plated wear-resistant refractory compound films such as nitrides and carbides are discussed.

Talivaldis Spalvins↗
DOE OSTI2024

Phase-Slip Lines and Anomalous Josephson Effects in Tungsten Nanoscale Cluster-Based Topological Insulator Nanobridges: Implications for Topologically Protected Qubits and Quantum Sensors

Superconducting topological systems formed by a strong 3D topological insulator (TI) in proximity to a conventional s-wave superconductor (SC) have been intensely studied, as they may host Majorana zero modes. However, there are limited experimental realizations of TI-SC systems in which robust superconducting pairing is induced on the surface states of the TI and a topological superconducting state is established. Here, we fabricate a TI-SC system by depositing, via a focused ion beam, tungsten (W) nanoscale clusters on the surface of TI Bi 0.91 Sb 0.09 . We find that the resulting heterostructure supports phase-slip lines (PSLs) that act as effective Josephson junctions (JJs). Here, we probe the response of the system to microwave radiation. We find that for some ac frequencies, and powers, the resulting Shapiro steps’ structure of the voltage–current characteristic exhibits a missing first step and an unexpectedly wide second Shapiro step. The theoretical analysis of the measurements shows that the unusual Shapiro response arises from the interplay between a static JJ and a dynamic one and allows us to identify the conditions under which the missing first step can be attributed to the topological nature of the JJs formed by the PSLs. Our results suggest an approach to induce superconductivity in a TI, a route to realizing highly transparent topological JJs, and show how the response of superconducting systems to microwave radiation can be used to infer the dynamics of PSLs. Highly transparent topological junctions are promising candidates to realize vector field sensors with very high sensitivity. In addition, due to the nontrivial Berry phase of the TI’s surface states such junctions can be in a topological state which is ideal to create topologically protected qubits.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Visualizing Lithium Dendrite Formation within Solid-State Electrolytes

Solid-state electrolyte (SSE) is promising for application in allsolid-state lithium metal batteries because of its reliable safety and longevity. The failure of SSE to suppress dendrite formation of Li metal anodes has been conventionally explained by uneven Li deposition at Li/SSE interfaces and its subsequent dendritic growth. While Li deposition within SSE has been recently proposed as another key cause for SSE failure, little is known regarding the Li growth details inside the SSE itself. In this work, we performed in situ microscopic observation of Li deposition inside the SSE and obtained visualized evidence regarding the dynamic process of Li dendrite formation and growth. Here, Li is seen to directly nucleate and propagate within the SSE, leading to its structural cracking. Such behavior should be caused by the presence of P- and S-based crystalline defects in Li 3 PS 4 SSE, which is consistent with the cryo-transmission electron microscopy observations and theoretical calculations. This observation provides important insights into the growth mechanisms of Li dendrites within a working lithium battery.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Atomic order of rare earth ions in a complex oxide: a path to magnetotaxial anisotropy

Abstract Complex oxides offer rich magnetic and electronic behavior intimately tied to the composition and arrangement of cations within the structure. Rare earth iron garnet films exhibit an anisotropy along the growth direction which has long been theorized to originate from the ordering of different cations on the same crystallographic site. Here, we directly demonstrate the three-dimensional ordering of rare earth ions in pulsed laser deposited (Eu x Tm 1-x ) 3 Fe 5 O 12 garnet thin films using both atomically-resolved elemental mapping to visualize cation ordering and X-ray diffraction to detect the resulting order superlattice reflection. We quantify the resulting ordering-induced ‘magnetotaxial’ anisotropy as a function of Eu:Tm ratio using transport measurements, showing an overwhelmingly dominant contribution from magnetotaxial anisotropy that reaches 30 kJ m −3 for garnets with x = 0.5. Control of cation ordering on inequivalent sites provides a strategy to control matter on the atomic level and to engineer the magnetic properties of complex oxides.

Science & Technology - Other Topics↗
DOE OSTI2021

Engineering catalyst supports to stabilize PdO x two-dimensional rafts for water-tolerant methane oxidation

The treatment of emissions from natural gas engines is an important area of research since methane is a potent greenhouse gas. The benchmark catalysts, based on Pd, still face challenges such as water poisoning and long-term stability. In this work, we report an approach for catalyst synthesis that relies on the trapping of metal single atoms on the support surface, in thermally stable form, to modify the nature of further deposited metal/metal oxide. By anchoring Pt ions on a catalyst support we can tailor the morphology of the deposited phase. In particular, two-dimensional (2D) rafts of PdO x are formed, resulting in higher reaction rates and improved water tolerance during methane oxidation. The results show that modifying the support by trapping single atoms could provide an important addition to the toolkit of catalyst designers for controlling the nucleation and growth of metal and metal oxide clusters in heterogeneous catalysts.

2D raft↗
DOE OSTI2021

Strong Fermi-level pinning at metal contacts to halide perovskites

The performance of halide perovskite-based electronic and optoelectronic devices is often related to interfacial charge transport. To shed light on the underlying physical and chemical properties of CH 3 NH 3 PbI 3 (MAPbI 3 ) in direct contact with common electrodes Al, Ti, Cr, Ag, and Au, the evolution of interfacial properties and Fermi level pinning is systematically studied. Given a unique experimental facility, pristine interfaces without any exposure to ambient air were prepared. We observe aggregation of substantial amounts of metallic lead (Pb 0 ) at the metal/MAPbI 3 interface, resulting from the interfacial reaction between the deposited metal and iodine ions from MAPbI 3 . It is found that the Schottky barrier height at the metal/MAPbI 3 interface is independent of the metal work function due to strong Fermi level pinning, possibly due to the metallic Pb 0 aggregates, which act as interfacial trap sites. The charge neutrality level of MAPbI 3 is consistent with the energy level of Pb 0 -related defects, indicating that Pb 0 interfacial trap states can be nonradiative recombination sites. Here this work underlines that control of chemical bonding at interfaces is a key factor for designing future halide perovskite-based devices.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Origin and effect of film sub-stoichiometry on ultraviolet, ns-laser damage resistance of hafnia single layers

Understanding the origin of laser damage-prone precursors in high index materials such as hafnia holds the key to the development of laser damage-resistant multilayer dielectric coated optics for high power and energy laser systems. In this study, we investigate the source of sub-stoichiometry, a potent laser damage precursor, in hafnia films produced by an ion beam sputtering (IBS) deposition method and the effect of such defects on the film performance upon ns ultraviolet (UV) laser (8 ns, 355 nm) exposure. Chemical analysis of data obtained via Rutherford backscattering spectroscopy (RBS) suggests that hafnia films deposited at two different planetary locations from the same deposition run exhibit anisotropic and location-dependent stoichiometries. While the oxygen-to-hafnium ratio is at the stoichiometric value of 2 for the hafnia film at the edge location, the ratio is significantly deviated and is 1.7 for that deposited at the planetary center. The sub-stoichiometric hafnia films display a much lower 1-on-1 damage onset at 1.6 ± 0.2 J/cm 2 compared to 2.3 ± 0.2 J/cm 2 in a stoichiometric film. The low damage performance films also have an over three times higher damage density at fluences above initiation. Coupled with Monte Carlo simulations, we reveal that sub-stoichiometry is primarily attributed to preferential removal of oxygen during film deposition by the bombardment of energetic reflected argon neutrals. The resulting oxygen deficiencies create the sub-bandgap states which facilitate the strong laser energy coupling and reduce the resistance to laser-induced damage in the hafnia single layer films.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Energy Evolution from the Chromosphere to the Heliosphere in the 2021 October 28 Solar Eruption

We perform a detailed study of the energetics for a well-observed solar eruption and flare that occurred on 2021 October 28. This event included a GOES class X1.0 flare, a global extreme-UV (EUV) wave, and a coronal mass ejection (CME) that reached speeds of >2000 km s −1 . The event was observed from a variety of spacecraft in NASA’s Heliophysics System Observatory, including multiple missions near Earth, STEREO-A off the Sun-Earth line, and Solar Orbiter, near the Sun-Earth line at about 0.8 au. Using remote sensing, in situ observations, and in some cases scaling laws based on previous observations, we characterize the following quantities: free magnetic energy, energy in nonthermal electrons, energy in nonthermal ions, bolometric energy, energy deposited in the chromosphere, thermal energy radiated in the flare loops, energy dissipated by the EUV wave, CME kinetic and gravitational potential energy, CME energy flux in the heliosphere, and the energy partition in the CME shock. We find that the total energy released during the event is consistent with estimates of the pre-event stored magnetic energy, and the CME kinetic + potential energy dominates the energy partition.

solar coronal mass ejection shocks↗
NASA NTRS1970

Low stress integral coverslips

Low stress integral coverslips deposition by high vacuum ion beam sputtering for solar cell manufacturing cost reduction

Bartels, F. T. C.↗
NASA NTRS1971

Behavior of hydrogen on nickel

Hydrogen adsorption behavior on polycrystalline nickel surfaces, using electron impact desorption flash filament with gas phase and ion spectrometer and vapor deposition

Gilbreath, W. P.↗
NASA NTRS1974

Eight-cm mercury ion thruster system technology

The technology status of 8 cm diameter electron bombardment ion thrusters is presented. Much of the technology resulting from the 5 cm diameter thruster has been adapted and improved upon to increase the reliability, durability, and efficiency of the 8 cm thruster. Technology discussed includes: dependence of neutralizer tip erosion upon neutralizer flow rate; impregnated and rolled-foil insert cathode performance and life testing; neutralizer position studies; thruster ion beam profile measurements; high voltage pulse ignition; high utilization ion machined accelerator grids; deposition internal and external to the thruster; thruster vectoring systems; thruster cycling life testing and thruster system weights for typical mission applications.

Source record↗