Results for “degrees of freedom” — Page 19

NASA NTRS1973

Hybrid 3-D rocket trajectory program. Part 1: Formulation and analysis. Part 2: Computer programming and user's instruction

Models utilizing various sub-sets of the six degrees of freedom are used in trajectory simulation. A 3-D model with only linear degrees of freedom is especially attractive, since the coefficients for the angular degrees of freedom are the most difficult to determine and the angular equations are the most time consuming for the computer to evaluate. A computer program is developed that uses three separate subsections to predict trajectories. A launch rail subsection is used until the rocket has left its launcher. The program then switches to a special 3-D section which computes motions in two linear and one angular degrees of freedom. When the rocket trims out, the program switches to the standard, three linear degrees of freedom model.

Huang, L. C. P.↗

DOE OSTI2020

Robust d x 2 - y 2 -wave superconductivity of infinite-layer nickelates

Motivated by the recent observation of superconductivity in strontium-doped NdNiO 2 , we study the superconducting instabilities in this system from various vantage points. Starting with first-principles calculations, we construct two distinct tight-binding models, a simpler single-orbital as well as a three-orbital model, both of which capture the key low-energy degrees of freedom to varying degrees of accuracy. We study superconductivity in both models using the random phase approximation. We then analyze the problem at stronger coupling, and study the dominant pairing instability in the associated t-J model limit. Finally, in all instances, the dominant pairing tendency is in the d x 2 -y 2 channel, analogous to the cuprate superconductors.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

NASA NTRS1988

Grasping with mechanical intelligence

Many robotic hands have been designed and a number have been built. Because of the difficulty of controlling and using complex hands, which usually have nine or more degrees of freedom, the simple one- or two-degree-of-freedom gripper is still the most common robotic end effector. A new category of device is presented: a medium-complexity end effector. With three to five degrees of freedom, such a tool is much easier to control and use, as well as more economical, compact and lightweight than complex hands. In order to increase the versatility, it was necessary to identify grasping primitives and to implement them in the mechanism. In addition, power and enveloping grasps are stressed over fingertip and precision grasps. The design is based upon analysis of object apprehension types, requisite characteristics for active sensing, and a determination of necessary environmental interactions. Contained are the general concepts necessary to the design of a medium-complexity end effector, an analysis of typical performance, and a computer simulation of a grasp planning algorithm specific to this type of mechanism. Finally, some details concerning the UPenn Hand-a tool designed for the research laboratory-are presented.

Ulrich, Nathan Thatcher↗

NASA NTRS1973

A comparison of results from two simulators used for studies of astronaut maneuvering units

A comparison of the results from a fixed-base, six-degree-of -freedom simulator and a moving-base, three-degree-of-freedom simulator was made for a close-in, EVA-type maneuvering task in which visual cues of a target spacecraft were used for guidance. The maneuvering unit (the foot-controlled maneuvering unit of Skylab Experiment T020) employed an on-off acceleration command control system operated entirely by the feet. Maneuvers by two test subjects were made for the fixed-base simulator in six and three degrees of freedom and for the moving-base simulator in uncontrolled and controlled, EVA-type visual cue conditions. Comparisons of pilot ratings and 13 different quantitative parameters from the two simulators are made. Different results were obtained from the two simulators, and the effects of limited degrees of freedom and uncontrolled visual cues are discussed.

Stewart, E. C.↗

NASA NTRS2002

Controller Design for the ST7 Disturbance Reduction System

The Space Technology 7 experiment will perform an on-orbit system-level validation of two specific Disturbance Reduction System technologies: a gravitational reference sensor employing a free-floating test mass and a set of micro-Newton colloidal thrusters. The Disturbance Reduction System is designed to maintain a spacecraft's position with respect to the free-floating test mass to less than 10 nm/ square root of Hz, over the frequency range 10(exp -3) Hz to 10(exp -2) Hz. This paper presents the design and analysis of the coupled drag-free and attitude control system that closes the loop between the gravitational reference sensor and the micro-Newton thrusters while incorporating star tracker data at low frequencies. The effects of actuation and measurement noise and disturbances on the spacecraft and test masses are evaluated in a seven-degree-of-freedom planar model incorporating two translational and one rotational degrees of freedom for the spacecraft and two translational degrees of freedom for each test mass.

Maghami, Peiman↗

NASA NTRS2003

Design and Analysis of the ST7 Disturbance Reduction System (DRS) Spacecraft Controller

The Space Technology 7 experiment will perform an on-orbit system-level validation of two specific Disturbance Reduction System technologies: a gravitational reference sensor employing a free-floating test mass and a set of micronewton colloidal thrusters. The Disturbance Reduction System is designed to maintain a spacecraft's position with respect to the free-floating test mass to less than 10 nm/square root of Hz, over the frequency range 10(exp -3) Hz to 10(exp -2) Hz. This paper presents the design and analysis of the coupled drag-free and attitude control system that closes the loop between the gravitational reference sensor and the micronewton thrusters while incorporating star tracker data at low frequencies. The effects of actuation and measurement noise and disturbances on the spacecraft and test masses are evaluated in a seven-degree-of-freedom planar model incorporating two translational and one rotational degrees of freedom for the spacecraft and two translational degrees of freedom for each test mass.

Maghami, P. G.↗

NASA NTRS2011

ATHLETE: A Cargo-Handling Vehicle for Solar System Exploration

As part of the NASA Exploration Technology Development Program, the Jet Propulsion Laboratory is developing a vehicle called ATHLETE: the All-Terrain Hex-Limbed Extra-Terrestrial Explorer. Each vehicle is based on six wheels at the ends of six multi-degree-of-freedom limbs. Because each limb has enough degrees of freedom for use as a general-purpose leg, the wheels can be locked and used as feet to walk out of excessively soft or other extreme terrain. Since the vehicle has this alternative mode of traversing through or at least out of extreme terrain, the wheels and wheel actuators can be sized for nominal terrain. There are substantial mass savings in the wheel and wheel actuators associated with designing for nominal instead of extreme terrain. These mass savings are comparable-to or larger-than the extra mass associated with the articulated limbs. As a result, the entire mobility system, including wheels and limbs, can be about 25% lighter than a conventional mobility chassis. A side benefit of this approach is that each limb has sufficient degrees-of-freedom to use as a general-purpose manipulator (hence the name "limb" instead of "leg"). Our prototype ATHLETE vehicles have quick-disconnect tool adapters on the limbs that allow tools to be drawn out of a "tool belt" and maneuvered by the limb. A power-take-off from the wheel actuates the tools, so that they can take advantage of the 1+ horsepower motor in each wheel to enable drilling, gripping or other power-tool functions. Architectural studies have indicated that one useful role for ATHLETE in planetary (moon or Mars) exploration is to "walk" cargo off the payload deck of a lander and transport it across the surface. Recent architectural approaches are focused on the concept that the lander descent stage will use liquid hydrogen as a propellant. This is the highest performance chemical fuel, but it requires very large tanks. A natural geometry for the lander is to have a single throttleable rocket engine on the centerline at the bottom, and to have the propellant tanks arranged as compactly as possible around and above that engine, with nearly-straight structural load paths that carry the heavy LO2 tanks as well as the ascent stage or cargo on a top deck. (The requirement for exactly one descent engine stems from the need to avoid symmetry planes in the exhaust plume that can entrain surface particles and loft them up into the system at hypervelocity.) This geometry is especially attractive since abort considerations drive the ascent stage to have as much open space around it as possible, in case the ascent stage needs to fire away from an out-of-control descent stage. These considerations lead to a configuration where the cargo deck of the lander is relatively high off the ground (over 6 meters in current concepts, using a 10-meter diameter launch shroud). These considerations have led some observers to presume that there is a "lander offloading problem". ATHLETE has been demonstrated as a solution to this problem, walking cargo off the high deck. This paper describes the applicability of the ATHLETE concept to exploration of the moon, Mars and even to Near- Earth Objects. Recent field test results for long-range traverse are described, along with plans for testing in the simulated microgravity environment of a NEO.

Space Robotics↗

NASA NTRS2012

ATHLETE: A Limbed Vehicle for Solar System Exploration

As part of the Human-Robot Systems project funded by NASA, the Jet Propulsion Laboratory has developed a vehicle called ATHLETE: the All-Terrain Hex-Limbed Extra-Terrestrial Explorer. Each vehicle is based on six wheels at the ends of six multi-degree-of-freedom limbs. Because each limb has enough degrees of freedom for use as a general-purpose leg, the wheels can be locked and used as feet to walk out of excessively soft or other extreme terrain. Since the vehicle has this alternative mode of traversing through or at least out of extreme terrain, the wheels and wheel actuators can be sized for nominal terrain. There are substantial mass savings in the wheel and wheel actuators associated with designing for nominal instead of extreme terrain. These mass savings are comparable-to or larger-than the extra mass associated with the articulated limbs. As a result, the entire mobility system, including wheels and limbs, can be about 25% lighter than a conventional mobility chassis. A side benefit of this approach is that each limb has sufficient degrees-of-freedom to use as a general-purpose manipulator (hence the name "limb" instead of "leg"). Our prototype ATHLETE vehicles have quick-disconnect tool adapters on the limbs that allow tools to be drawn out of a "tool belt" and maneuvered by the limb.

Space Robotics↗

NASA NTRS2010

ATHLETE: Lunar Cargo Unloading from a High Deck

As part of the NASA Exploration Technology Development Program, the Jet Propulsion Laboratory is developing a vehicle called ATHLETE: the All-Terrain Hex-Limbed Extra-Terrestrial Explorer. Each vehicle is based on six wheels at the ends of six multi-degree-of freedom limbs. Because each limb has enough degrees of freedom for use as a general-purpose leg, the wheels can be locked and used as feet to walk out of excessively soft or other extreme terrain. Since the vehicle has this alternative mode of traversing through or at least out of extreme terrain, the wheels and wheel actuators can be sized for nominal terrain. There are substantial mass savings in the wheel and wheel actuators associated with designing for nominal instead of extreme terrain. These mass savings are at least comparable-to or larger-than the extra mass associated with the articulated limbs. As a result, the entire mobility system, including wheels and limbs, can be lighter than a conventional all-terrain mobility chassis. A side benefit of this approach is that each limb has sufficient degrees-of freedom to be used as a general-purpose manipulator (hence the name "limb" instead of "leg"). Our prototype ATHLETE vehicles have quick-disconnect tool adapters on the limbs that allow tools to be drawn out of a "tool belt" and maneuvered by the limb. A power-take-off from the wheel actuates the tools, so that they can take advantage of the 1+ horsepower motor in each wheel to enable drilling, gripping or other power-tool functions.

robotics↗

NASA NTRS2009

ATHLETE: a Cargo and Habitat Transporter for the Moon

As part of the NASA Exploration Technology Development Program, the Jet Propulsion Laboratory is developing a vehicle called ATHLETE: the All-Terrain Hex-Limbed Extra-Terrestrial Explorer. The vehicle concept is based on six wheels at the ends of six multi-degree-of-freedom limbs. Because each limb has enough degrees of freedom for use as a general-purpose leg, the wheels can be locked and used as feet to walk out of excessively soft or other extreme terrain. Since the vehicle has this alternative mode of traversing through (or at least out of) extreme terrain, the wheels and wheel actuators can be sized only for nominal terrain. There are substantial mass savings in the wheels and wheel actuators associated with designing for nominal instead of extreme terrain. These mass savings are comparable-to or larger-than the extra mass associated with the articulated limbs. As a result, the entire mobility system, including wheels and limbs, can be about 25 percent lighter than a conventional mobility chassis for planetary exploration. A side benefit of this approach is that each limb has sufficient degrees-of-freedom for use as a general-purpose manipulator (hence the name "limb" instead of "leg"). Our prototype ATHLETE vehicles have quick-disconnect tool adapters on the limbs that allow tools to be drawn out of a "tool belt" and maneuvered by the limb. A rotating power-take-off from the wheel actuates the tools, so that they can take advantage of the 1-plus-horsepower motor in each wheel to enable drilling, gripping or other power-tool functions.

mobile habitats↗

DOE OSTI2020

Spin crossovers and superdiffusion in the one-dimensional Hubbard model

We use tools from integrability and generalized hydrodynamics to study finite-temperature dynamics in the one-dimensional Hubbard model. First, we examine charge, spin, and energy transport away from half-filling and zero magnetization, focusing on the strong coupling regime where we identify a rich interplay of temperature and energy scales, with crossovers between distinct dynamical regimes. We identify an intermediate-temperature regime analogous to the spin-incoherent Luttinger liquid, where spin degrees of freedom are hot but charge degrees of freedom are at low temperature. We demonstrate that the spin Drude weight exhibits sharp features at the crossover between this regime and the low-temperature Luttinger liquid regime, which are absent in the charge and energy response, and rationalize this behavior in terms of the properties of Bethe ansatz quasiparticles.We then turn to the dynamics along special lines in the phase diagram corresponding to half-filling and/or zero magnetization where on general grounds we anticipate that the transport is subballistic but superdiffusive. We provide analytical and numerical evidence for Kardar-Parisi-Zhang (KPZ) dynamical scaling (with length and time scales related via x ~ t 2/3 ) along both lines and at the SO(4)-symmetric point where they intersect. Furthermore, our results suggest that both spin-coherence crossovers and KPZ scaling may be accessed in near-term experiments with optical lattice Hubbard emulators.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

NASA NTRS1972

A proposed remote manipulator system: A concept

System is described with variable ratio, mixed mode, bilateral, master-slave control. Manipulator arms consist of shoulder and elbow with two degrees of freedom, a wrist with three degrees of freedom, and terminal grasping device. Feedback is provided by TV cameras attached near shoulder, grasping device, and at end of shuttle opposite arm.

Brodie, S.↗

NASA NTRS1973

New plate and shell elements for NASTRAN

A new higher order triangular plate-bending finite element is presented which possesses high accuracy for practical mesh subdivisions and which uses only translations and rotations as grid point degrees of freedom. The element has 18 degrees of freedom, the transverse displacement and two rotations at the vertices and mid-side grid points of the triangle. The transverse displacement within the element is approximated by a quintic polynomial; the bending strains thus vary cubically within the element. Transverse shear flexibility is taken into account in the stiffness formulation. Two examples of static and dynamic analysis are included to show the behavior of the element.

Narayanaswami, R.↗

NASA NTRS1993

Evaluation of actuators for the SDOF and MDOF active microgravity isolation systems

The University of Virginia examined the design of actuators for both single-degree-of-freedom (SDOF) and multiple-degree-of-freedom (MDOF) active microgravity isolation systems. For SDOF systems, two actuators were considered: a special large gap magnetic actuator and a large stroke Lorentz actuator. The magnetic actuator was viewed to be of greater difficulty than the Lorentz actuator with little compelling technical advantage and was dropped from consideration. A Lorentz actuator was designed and built for the SDOF test rig using magnetic circuit and finite element analysis. The design and some experimental results are discussed. The University also examined the design of actuators for MDOF isolation systems. This includes design of an integrated 1 cm gap 6-DOF noncontacting magnetic suspension system and of a 'coarse' follower which permits the practical extension of magnetic suspension to large strokes. The proposed 'coarse' actuator was a closed kinematic chain manipulator known as a Stewart Platform. The integration of the two isolation systems together, the isolation tasks assigned to each, and possible control architectures were also explored. The results of this research are examined.

Source record↗

NASA NTRS1993

Control of a serpentine manipulator with collision avoidance

The robotics lab at the Kennedy Space Center is investigating the possibility of using a 'serpentine' manipulator for Shuttle inspection and payload processing. Serpentine manipulators are characterized by a large number of degrees of freedom giving them a high degree of redundancy. This redundancy allows them to be used to reach confined areas while avoiding collisions with their environment. In this paper, the author describes a new approach to controlling the joint rates for an n degree of freedom robot such that it moves its end effector to a desired position while simultaneously avoiding collision of any part of the robot arm with obstacles. Joint rates which move the end effector toward the target are found via a Lyapunov stability function. The gradient of an obstacle cost function indicates the direction toward obstacle collision in the joint space. The component of the end effector joint rates orthogonal to the obstacle gradient becomes the commanded joint rates. A notional eleven DOF model is used to numerically demonstrate the efficacy of the control law.

Byers, Robert M.↗

DOE OSTI2024

Measurement of the Pion Exclusive Electro-Production Cross-Section in the E12-19-006 Experiment in Hall-C at Jefferson Lab

One of the most effective methods for exploring the transition from hadronic degrees of freedom to quark-gluon degrees of freedom in Quantum Chromodynamics (QCD) is through the investigation of \exclusive" pion and kaon electro-production reactions at various Q2 and ?t values. The E12-19-006 experiment is conducted within the confi?nes of experimental Hall C at the Thomas Jefferson National Accelerator Facility, USA, for such studies. The primary aim of the experiment is to ?first enhance our comprehension of the pion electro-production cross-section and its form factor at Q2 = 0.38 and 0.42 GeV2. This is the fi?rst run period of the E12-19-006 experiment which ran in summer 2019. A more profound understanding of the pion electro-production reaction, 1H(e,e'?+)n, at low Q2 is deemed essential to employ this electro-production reaction (an indirect technique) for the high Q2 studies, thereby delving deeper into the realm of QCD. Consequently, this dissertation presents a thorough analysis of the experimental data acquired in the ?first run period of the E12-19-006 experiment. In pursuit of precision, a series of systematic studies (target boiling correction study, the elastic reaction cross-section measurements, study for determining vari- ous kinematics o?sets, etc.) are conducted to discern the accuracy of the analyzed data, a prerequisite for the use of Rosenbluth separation technique to separate the pion electro-production cross-section terms in t bins. The separated pion electro-production cross-section through the Rosenbluth separation technique is then used to extract the pion electromagnetic form factor. In this dissertation, the pion electro-production cross-section is carefully dissected into its four constituent components: longitudinal (?L), transverse (?T ), longitudinal-transverse (?LT ), and transverse-transverse (?TT ), using the full version of Rosenbluth separation technique for the Q2 = 0.38 GeV2. The technique is simultaneously fi?tted to the unseparated pion electro-production cross-sections at the three values of polarization of the virtual photon (?), i.e., ? = 0.286, 0.629 and 0.781. An iterative process is applied to re?ne the parameters of the model cross-sections until the yield ratio of experimental and Monte Carlo simulation converges. In this study, 21 iterations are conducted to re?ne the model cross-section parameters. The fi?nal pion electro-production cross-section terms are then determined for 7 t bins using the optimized parameters of the model cross-sections.

Kumar, Vijay↗

NASA NTRS1989

A multi-point force appropriation method based upon a singular value decomposition approach

Force appropriation methods aim to provide an estimate for the force pattern required to excite a 'pure' normal mode in a vibration test where multiple exciters are available. In this paper, a new method based upon a Singular Value Decompositon approach is presented. The appropriated force vector which minimizes the in-plane response components while maximizing the required quadrature components is found, subject to a fixed force norm. The method can accommodate more transducers than exciters and also more exciters than effective degrees of freedom. The method is demonstrated upon a six degree of freedom theoretical model and it is shown that an estimate for the effective degrees of freedom can be obtained.

Juang, Jer-Nan↗

NASA NTRS1994

Programs To Optimize Spacecraft And Aircraft Trajectories

POST/6D POST is set of two computer programs providing ability to target and optimize trajectories of powered or unpowered spacecraft or aircraft operating at or near rotating planet. POST treats point-mass, three-degree-of-freedom case. 6D POST treats more-general rigid-body, six-degree-of-freedom (with point masses) case. Used to solve variety of performance, guidance, and flight-control problems for atmospheric and orbital vehicles. Applications include computation of performance or capability of vehicle in ascent, or orbit, and during entry into atmosphere, simulation and analysis of guidance and flight-control systems, dispersion-type analyses and analyses of loads, general-purpose six-degree-of-freedom simulation of controlled and uncontrolled vehicles, and validation of performance in six degrees of freedom. Written in FORTRAN 77 and C language. Two machine versions available: one for SUN-series computers running SunOS(TM) (LAR-14871) and one for Silicon Graphics IRIS computers running IRIX(TM) operating system (LAR-14869).

Brauer, G. L.↗