SEARCH · Engineering Papers

Results for “residual minimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

All sources NASA NTRS DOE OSTI

NASA NTRS1973

Analysis of multiple pulse NMR in solids

The general problems associated with the removal of the effects of dipolar broadening from solid-state NMR spectra are analyzed. The effects of finite pulse width and H sub 1 inhomogeneity are shown to have limited the resolution of previous pulse cycles, and a new eight-pulse cycle designed to minimize these problems is discussed. Spectra for F-19 in CaF2 taken with this cycle are presented which show residual linewidth near 10 Hz. The feasibility of measuring proton chemical shift tensors is discussed.

Rhim, W.-K.↗

NASA NTRS1991

Analysis of pressure-broadened ozone spectra in the 3 micron region

This work involves the analysis of a series of McMath Fourier Transform Infrared (FTIR) spectra of ozone broadened by mixing with air (four different pressures), nitrogen (three pressures), or oxygen (three pressures). Each spectrum covers the region from 2396 to 4057 cm(-1). This study focused on the 3 sub nu sub 3 band in t 3000 to 3060 cm(-1). The band is analyzed by first dividing its region into small intervals containing a few well isolated absorption lines of reasonable intensity. Each of these small intervals is fit by multiple iterations of the nonlinear least squares program until residuals (the difference between calculated and observed spectrum, as a percent of the strongest intensity in the interval) are minimized to a reasonable value which corresponds to the noise level of the measured spectrum. Position, intensity, and half-width are recorded for later analysis. From the measured half-widths, a pressure broadening coefficient was determined for each absorption line. Pressure shifts were determined by comparing observed line positions in the spectra of the diluted ozone samples to tabulated line positions determined from spectra of pure gas samples. Comparisons to other work on ozone indicate that the broadening and shift coefficients determined in this study are consistent with those determined in other spectral regions.

Prochaska, Eleanor S.↗

DOE OSTI2020

Oxy-Combustion System Process Optimization

The overall objective of this work is to develop a new chemical absorbent-based, high pressure, CO 2 purification system to remove the residual oxygen that currently contaminates the recovered CO 2 , and to optimize the Pressurized Oxy-Combustion (POxC) process to minimize the Cost of Electricity (COE) generated in this advanced combustion process. TDA developed and validated the performance of the oxygen removal system for CO 2 purification. In collaboration with the Advanced Power & Energy Program (APEP) of University of California, Irvine (UCI), we optimized the POxC process, including thermal management, heat integration, and power cycle optimization using process design and modeling supported with Aspen Plus® process simulations. The techno-economic analysis results indicate that the pressurized oxycombustion coal power plant with Ion-transport membrane (ITM) air separation unit (ASU) (Case 2 – 30.55%) does not show an advantage over a cryogenic ASU (Case 1 – 31.24%) while TDA’s sorption-based ASU (Case 4 - 32.61%) shows a significant advantage over the cryogenic ASU (Case 1 – 331.24%). The specific plant costs show a wide range with a low of $2544/kW for Case 11C (TDA ASU, co-sequestering the SO x , and ultra-supercritical steam cycle) to a high of $2975/kW for Case 12A (cryogenic ASU and sCO 2 cycle). In general, the ITM ASU based cases have lower specific plant costs than the corresponding cryogenic ASU based cases while the TDA ASU based cases show the lowest specific plant costs. The main reason for lowering these costs is the higher overall plant thermal efficiency which decreases the plant cost on a $ per kW basis. Next comparing the cases with different power cycle working fluid conditions in terms of temperature and pressure while all utilizing steam, similar trends as the plant costs may be observed. However, with the supercritical CO 2 (sCO 2 ) cycle, the increase in thermal efficiency of the sCO 2 cycle was not able to offset its increase in plant cost making the plant costs higher than those of the corresponding steam cycle cases. The Cost of Electricity (COE) again shows similar trends as the specific plant costs. The COE for Case 11C at $110.1/MWh is also the lowest, but among all cases that do not co-sequester the SO x , Case 12C (TDA ASU and sCO 2 cycle) has the lowest COE at $\$$117.5/MWh while the highest is for Case 8A (cryogenic ASU and supercritical steam cycle) at $130.4/MWh.

20 FOSSIL-FUELED POWER PLANTS↗

NASA NTRS2003

Case Studies of Fatigue Life Improvement Using Low Plasticity Burnishing in Gas Turbine Engine Applications

Surface enhancement technologies such as shot peening, laser shock peening (LSP), and low plasticity burnishing (LPB) can provide substantial fatigue life improvement. However, to be effective, the compressive residual stresses that increase fatigue strength must be retained in service. For successful integration into turbine design, the process must be affordable and compatible with the manufacturing environment. LPB provides thermally stable compression of comparable magnitude and even greater depth than other methods, and can be performed in conventional machine shop environments on CNC machine tools. LPB provides a means to extend the fatigue lives of both new and legacy aircraft engines and ground-based turbines. Improving fatigue performance by introducing deep stable layers of compressive residual stress avoids the generally cost prohibitive alternative of modifying either material or design. The X-ray diffraction based background studies of thermal and mechanical stability of surface enhancement techniques are briefly reviewed, demonstrating the importance of minimizing cold work. The LPB process, tooling, and control systems are described. An overview of current research programs conducted for engine OEMs and the military to apply LPB to a variety of engine and aging aircraft components are presented. Fatigue performance and residual stress data developed to date for several case studies are presented including: * The effect of LPB on the fatigue performance of the nickel based super alloy IN718, showing fatigue benefit of thermal stability at engine temperatures. * An order of magnitude improvement in damage tolerance of LPB processed Ti-6-4 fan blade leading edges. * Elimination of the fretting fatigue debit for Ti-6-4 with prior LPB. * Corrosion fatigue mitigation with LPB in Carpenter 450 steel. *Damage tolerance improvement in 17-4PH steel. Where appropriate, the performance of LPB is compared to conventional shot peening after exposure to engine operating temperatures.

Prevey, Paul S.↗

DOE OSTI2024

Vadose zone flushing of fertilizer tracked by isotopes of water and nitrate

Abstract A substantial fraction of nitrogen (N) fertilizer applied in agricultural systems is not incorporated into crops and moves below the rooting zone as nitrate (NO 3 − ). Understanding mechanisms for soil N retention below the rooting zone and leaching to groundwater is essential for our ability to track the fate of added N. We used dual stable isotopes of nitrate (δ 15 N–NO 3 − and δ 18 O–NO 3 − ) and water (δ 18 O–H 2 O and δ 2 H–H 2 O) to understand the mechanisms driving nitrate leaching at three depths (0.8, 1.5, and 3.0 m) of an irrigated corn field sampled every 2 weeks from 2016 to 2020 in the southern Willamette Valley, Oregon, USA. Distinct periods of high nitrate concentrations with lower δ 15 N–NO 3 − values indicated that a portion of that nitrate was from recent fertilizer applications. We used a mixing model to quantify nitrate fluxes associated with recently added fertilizer N versus older, legacy soil N during these “fertilizer signal periods.” Nitrate leached below 3.0 m in these periods made up a larger proportion of the total N leached at that depth (∼52%) versus the two shallower depths (∼13%–16%), indicating preferential movement of recently applied fertilizer N through the deep soil into groundwater. Further, N associated with recent fertilizer additions leached more easily when compared to remobilized legacy N. A high volume of fall and winter precipitation may push residual fertilizer N to depth, potentially posing a larger threat to groundwater than legacy N. Optimizing fertilizer N additions could minimize fertilizer losses and reduce nitrate leaching to groundwater.

Agriculture↗

DOE OSTI2023

Molecular and Dual-Isotopic Profiling of the Microbial Controls on Nitrogen Leaching in Agricultural Soils under Managed Aquifer Recharge

Nitrate (NO 3 – ) leaching is a serious health and ecological concern in global agroecosystems, particularly those under the application of agricultural-managed aquifer recharge (Ag-MAR); however, there is an absence of information on microbial controls affecting NO 3 – leaching outcomes. We combine natural dual isotopes of NO 3 – ( 15 N/ 14 N and 18 O/ 16 O) with metagenomics, quantitative polymerase chain reaction (PCR), and a threshold indicator taxa analysis (TITAN) to investigate the activities, taxon profiles, and environmental controls of soil microbiome associated with NO 3 – leaching at different depths from Californian vineyards under Ag-MAR application. The isotopic signatures demonstrated a significant priming effect (P < 0.01) of Ag-MAR on denitrification activities in the topsoil (0–10 cm), with a 12–25-fold increase of 15 N–NO 3 – and 18 O–NO 3 – after the first 24 h of flooding, followed by a sharp decrease in the enrichment of both isotopes with ~80% decline in denitrification activities thereafter. In contrast, deeper soils (60–100 cm) showed minimal or no denitrification activities over the course of Ag-MAR application, thus resulting in 10–20-fold of residual NO 3 – being leached. Metagenomic profiling and laboratory microcosm demonstrated that both nitrifying and denitrifying groups, responsible for controlling NO 3 – leaching, decreased in abundance and potential activity rates with soil depth. TITAN suggested that Nitrosocosmicus and Bradyrhizobium, as the major nitrifier and denitrifier, had the highest and lowest tipping points with regard to the NO 3 – changes (P < 0.05), respectively. Overall, our study provides new insight into specific depth limitations of microbial controls on soil NO 3 – leaching in agroecosystems.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2020

Challenges and Solutions in Operation and Lay-Up of the Modular Caustic- Side Solvent Extraction Unit - 20078

The Modular Caustic-Side Solvent Extraction (CSSX) Unit (MCU) was designed and constructed to provide interim salt waste processing so that the Liquid Waste Disposition Program (LWDP) could continue waste removal and tank closure until start-up of the Salt Waste Processing Facility (SWPF). MCU processes Clarified Salt Solution (CSS), or salt solution (SS) that has undergone actinide removal/filtration, to produce two waste streams: the cesium laden Strip Effluent (SE), which is incorporated into glass at the Defense Waste Processing Facility (DWPF), and the cesium depleted Decontaminated SS (DSS), which is incorporated into grout at the Saltstone Production Facility (SPF). MCU completed start-up in 2008 with an initial operating life of 3 years and design life of 5 years. Prior to reaching the end of the design life, multiple critical components were upgraded and/or replaced to mitigate risks associated with any delays in SWPF start-up. During the remainder of operation (until June 2019), MCU was challenged to maximize processing with minimal additional modifications to repair/improve aging infrastructure, while maintaining low levels of risk to workers and the environment. Notable challenges during the extended operating life of the facility involved both mechanical and operational issues. Two of the most significant issues were the increased frequency of Process Vessel Ventilation (PVV) High Efficiency Particulate Air (HEPA) filter change-outs and the biofouling of the SE coalescer (SEC). The major impacts of both issues were that replacement of these components 1) resulted in high exposure to workers, and 2) required substantial downtime, thus hindering achievement of processing goals. PVV HEPA filter replacements are required based on dose rate and differential pressure (dP) limits. After introducing a higher-curie feed to MCU, the operating time between change outs was reduced by approximately half. SEC replacements are required based on dP limits. After restarting from an extended outage, the operating life of the SEC was significantly reduced by more than half due to biofouling. As a result of extensive troubleshooting and process improvements, the facility was able to recover performance and extend the operating life of the PVV HEPA filters and the SEC media. Through troubleshooting both of these issues, the facility was also able to learn from prior experience and adapt in order to minimize down time and maintain throughput. Although the facility took advantage of short periods of downtime to perform nonintrusive troubleshooting and minor corrective/preventative maintenance activities, longer outages were periodically required for corrective maintenance involving process cell entry. During these outages, remote tools and specialized shield plates were employed to minimize dose to workers. Mock-ups of non-routine maintenance activities were critical to early identification of potential issues and improvements, which shortened outage duration. Consistent with the facility's operational strategy, evolutions needed for MCU layup were identified and sequenced to ensure safe conditions within the facility, meet pre-defined criteria for lay-up configuration, and protect workers, while minimizing the impact to SWPF integration. De-inventory and flushing of process areas was prioritized so that the total residual inventory was reduced as efficiently as possible. This paper discusses lessons learned and best practices from troubleshooting unique issues, performing complex maintenance activities, and implementing a layup strategy that best supports the overall system mission. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

NASA NTRS1998

Isothermal Fatigue, Damage Accumulation, and Life Prediction of a Woven PMC

This dissertation focuses on the characterization of the fully reversed fatigue behavior exhibited by a carbon fiber/polyimide resin, woven laminate at room and elevated temperatures. Nondestructive video edge view microscopy and destructive sectioning techniques were used to study the microscopic damage mechanisms that evolved. The residual elastic stiffness was monitored and recorded throughout the fatigue life of the coupon. In addition, residual compressive strength tests were conducted on fatigue coupons with various degrees of damage as quantified by stiffness reduction. Experimental results indicated that the monotonic tensile properties were only minimally influenced by temperature, while the monotonic compressive and fully reversed fatigue properties displayed noticeable reductions due to the elevated temperature. The stiffness degradation, as a function of cycles, consisted of three stages; a short-lived high degradation period, a constant degradation rate segment composing the majority of the life, and a final stage demonstrating an increasing rate of degradation up to failure. Concerning the residual compressive strength tests at room and elevated temperatures, the elevated temperature coupons appeared much more sensitive to damage. At elevated temperatures, coupons experienced a much larger loss in compressive strength when compared to room temperature coupons with equivalent damage. The fatigue damage accumulation law proposed for the model incorporates a scalar representation for damage, but admits a multiaxial, anisotropic evolutionary law. The model predicts the current damage (as quantified by residual stiffness) and remnant life of a composite that has undergone a known load at temperature. The damage/life model is dependent on the applied multiaxial stress state as well as temperature. Comparisons between the model and data showed good predictive capabilities concerning stiffness degradation and cycles to failure.

Gyekenyesi, Andrew L.↗

DOE OSTI2022

The WISE-2MASS Survey: Red Quasars Into the Radio Quiet Regime

We present a highly complete sample of broad-line (Type 1) QSOs out to z ~ 3 selected by their mid-infrared colors, a method that is minimally affected by dust reddening. We remove host-galaxy emission from the spectra and fit for excess reddening in the residual QSOs, resulting in a Gaussian distribution of colors for unreddened (blue) QSOs, with a tail extending toward heavily reddened (red) QSOs, defined as having E(B – V) > 0.25. This radio-independent selection method enables us to compare red and blue QSO radio properties in both the FIRST (1.4 GHz) and VLASS (2–4 GHz) surveys. Consistent with recent results from optically selected QSOs from SDSS, we find that red QSOs have a significantly higher detection fraction and a higher fraction of compact radio morphologies at both frequencies. We employ radio stacking to investigate the median radio properties of the QSOs including those that are undetected in FIRST and VLASS, finding that red QSOs have significantly brighter radio emission and steeper radio spectral slopes compared with blue QSOs. Finally, we find that the incidence of red QSOs is strongly luminosity dependent, where red QSOs make up >40% of all QSOs at the highest luminosities. Overall, red QSOs comprise ~40% of higher luminosity QSOs, dropping to only a few percent at lower luminosities. Furthermore, red QSOs make up a larger percentage of the radio-detected QSO population. We argue that dusty AGN-driven winds are responsible for both the obscuration as well as excess radio emission seen in red QSOs.

79 ASTRONOMY AND ASTROPHYSICS↗

NASA NTRS2003

Depth and Distribution of CO2 Snow on Mars

The dynamic role of volatiles on the surface of Mars has been a subject of longstanding interest. In the pre-Viking era, much of the debate was necessarily addressed by theoretical considerations. A particularly influential treatment by Leighton and Murray put forth a simple model relying on solar energy balance, and led to the conclusion that the most prominent volatile exchanging with the atmosphere over seasonal cycles is carbon dioxide. Their model suggested that due to this exchange, atmospheric CO2 partial pressure is regulated by polar ice. While current thinking attributes a larger role to H2O ice than did the occasional thin polar coating this model predicted, the CO2 cycle appears to be essentially correct. There are a number of observational constraints on the seasonal exchange of surface volatiles with the atmosphere. The growth and retreat of polar CO2 frost is visible from Earth-based telescopes and from spacecraft in Mars orbit, both at visible wavelengths and in thermal IR properties of the surface. Recently, variations in Gamma ray and neutron fluxes have also been used to infer integrated changes in CO2 mass on the surface. Measurements made by Viking's Mars Atmospheric Water Detector experiment were sensitive to atmospheric H2O vapor abundance. Surface condensates and their transient nature were detected by the Viking landers. The study here is motivated by recent data collected by the Mars Global Surveyor, affording the opportunity to not only detect the lateral distribution of volatiles, but also to constrain the variable volumes of the reservoirs. We elaborate on a technique first employed by Smith et al. By examining averages of a large number of topographic measurements collected by the Mars Orbiter Laser Altimeter (MOLA), that study showed that the zonal pattern of deposition and sublimation of CO2 can be determined. In their first approach, reference surfaces were fit to all measurements in narrow latitude annuli, and the time dependent variations about those mean surfaces were examined. In their second approach, height measurements from pairs of tracks that cross on the surface were interpolated and differenced, forming a set of crossover residuals. These residuals were then examined as a function of time and latitude. The initial studies averaged over longitude to maximize signal and minimize noise in order to isolate the expected small signal. In this follow-up study we now attempt to extract the elevation change pattern also as a function of longitude, and we focus on the crossover approach.

Aharonson, Oded↗

DOE OSTI2020

Irrigation, carbon amelioration, nitrogen, and stover removal effects on continuous corn

Corn (Zea mays L.) residue or stover is harvested as supplemental feed for livestock and is a potential feedstock for cellulosic biofuels. Limited information is available on corn stover removal effects on grain yield under different irrigation rates, nitrogen (N) fertilizer rates, and practices to maintain soil carbon (C) and minimize soil erosion. Here, we evaluated potential interactions between irrigation rate (full or limited), C amelioration practices (cover crop, surface-applied manure, or no amelioration practice), fertilizer N management (125 or 200 kg N ha –1 ), and stover removal (residue removal or no residue removal), on no-till continuous corn grain yield located on a silt loam soil in south-central Nebraska (2011–2018). Stover removal increased (P = .0017) grain yield by 1.02 Mg ha –1 and grain N uptake compared with no stover removal. Manure increased corn grain yield by 899 kg ha –1 compared to either the control or cover crop with stover removal while C amelioration practices did not affect grain yield under stover retention. Grain N concentration was higher (P < .0001) with stover removal (13.2 g kg –1 ) than residue retained (12.7 g kg –1 ). Partial factor productivity (grain yield/N rate) was highest for manure treatments with residue removal. The farmgate N balance (N applied – N removed) from stover removal was negative, yet grain yield was not affected after eight growing seasons. Grain yield increased with stover removal and manure application resulting in a cost-effective C amelioration practice whereas incorporating a winter cover crop resulted in similar grain yield as the control.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2022

Primary radiation damage in bone evolves via collagen destruction by photoelectrons and secondary emission self-absorption

X-rays are invaluable for imaging and sterilization of bones, yet the resulting ionization and primary radiation damage mechanisms are poorly understood. Here we monitor in-situ collagen backbone degradation in dry bones using second-harmonic-generation and X-ray diffraction. Collagen breaks down by cascades of photon-electron excitations, enhanced by the presence of mineral nanoparticles. We observe protein disintegration with increasing exposure, detected as residual strain relaxation in pre-stressed apatite nanocrystals. Damage rapidly grows from the onset of irradiation, suggesting that there is no minimal ‘safe’ dose that bone collagen can sustain. Ionization of calcium and phosphorous in the nanocrystals yields fluorescence and high energy electrons giving rise to structural damage that spreads beyond regions directly illuminated by the incident radiation. Our findings highlight photoelectrons as major agents of damage to bone collagen with implications to all situations where bones are irradiated by hard X-rays and in particular for small-beam mineralized collagen fiber investigations.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Data for Optimizing Chemical-Free Pretreatment for Maximizing Oil/Lipid Recovery from Transgenic Bioenergy Crops and its Rapid Analysis Using Time Domain-NMR

Transgenic bioenergy crops have shown the potential to produce vegetative oil by accumulating energy-rich triacylglyceride molecules that can be converted into biofuels (biodiesel and biojet). These transgenic crops cater to improved biofuel yield by providing lipids along with cellulosic sugars. Efficient bioprocessing technologies are needed to utilize these transgenic plants to their maximum potential. To this end, this study investigates a low- and high-severity chemical-free hydrothermal pretreatment of transgenic oilcane 1566 bagasse with in situ lipids to maximize the recovery of lipids for biodiesel and fermentable sugars for ethanol with minimal inhibitor generation. Hydrothermal pretreatment at 170°C recovered ∼25% of total lipids in the pretreatment liquor, leaving the remainder in bagasse residue for hexane recovery post fermentation. The recovery of lipids in pretreatment liquor remained constant beyond 170°C. Along with lipids, ∼35% w/w and ∼50% w/w fermentable sugars were recovered post saccharification from bagasse pretreated at 170°C and 210°C for 20 min, respectively. Hydrothermal pretreatment at 170°C for 20 min provided the optimum conditions for maximum recovery of lipids and cellulosic sugars that resulted in enhanced biofuel yield per unit biomass. High severity pretreatment increased the generation of inhibitors beyond the tolerance of fermentation microorganisms. In addition, the application of time-domain proton NMR spectroscopy was extended to bioprocessing. NMR technology facilitated the analysis of total lipids, the composition of fatty acids, and the characterization of free and bound lipids in untreated and pretreated oilcane 1566 bagasse subsequent to each step of biomass to biofuel conversion.

Conversion↗

DOE OSTI2024

Bioblendstocks to Optimize Mixing Controlled Compression Ignition (MCCI) Engines

In this project, a team of researchers from the University of Massachusetts Lowell, the University of Maine, and Mainstream Engineering developed an integrated process for the product of bioblendstocks to optimize mixing controlled compression ignition (MCCI) engines. The objective was to improve the energy density, sooting propensity, and cetane number of base diesel fuel while maintaining cold weather behavior. The process converts woody biomass (e.g. sawmill residues) into bio-oil through selective fast pyrolysis; the bio-oil is then selectively upgraded to form selectively oxygenated, minimally-branched hydrocarbons using non-noble metal catalysts in combination with metal-catalyzed hydrogenation. Advanced predictive models, in conjunction with existing property databases, and experimental testing are used to evaluate overall bioblendstock properties and their impact on base diesel fuel. An iterative, targeted upgrading approach was implemented to optimize the proposed bioblendstock’s properties. Assessment methodologies included techno-economic analysis, life-cycle assessment, property testing, and engine testing. Ultimately, the project team successfully produced a viable bioblendstock while identifying critical process points related to scale-up efforts. It was found that producing pyrolysis oils at 500 degrees C and with pine particle sizes of 1-2 mm led to bio-oil with a higher yield (of approximately 45 wt%) and rich amounts of aromatic alcohols. The resultant pyrolysis oil was then upgraded using a sequence of mild hydrotreating, followed by catalytic etherification and esterification, followed by another final mild hydrotreating to produce a blendstock containing saturated species with a limited, but non-zero, amount of oxygen. The aromatic alcohols produced by pyrolysis were especially helpful in this regard, as the resulting bicycloethers and derivatives exhibited high cetane numbers. While most bulk properties of the bioblendstock met or exceeded targeted thresholds, viscosity and cloud point notably fell outside the expected range; this could be addressed by blending limits and/or through the use of additives that are commonplace in current refinding practices. Identification of a bioblendstock that can be produced economically at scale while improving the performance and emissions characteristics of internal combustion engines positively affects the economy by boosting domestic fuel production and the environment by decreasing harmful emissions and increasing efficiency.

09 BIOMASS FUELS↗

NASA NTRS1987

Modified independent modal space control method for active control of flexible systems

A modified independent modal space control (MIMSC) method is developed for designing active vibration control systems for large flexible structures. The method accounts for the interaction between the controlled and residual modes. It incorporates also optimal placement procedures for selecting the optimal locations of the actuators in the structure in order to minimize the structural vibrations as well as the actuation energy. The MIMSC method relies on an important feature which is based on time sharing of a small number of actuators, in the modal space, to control effectively a large number of modes. Numerical examples are presented to illustrate the application of the method to generic flexible systems. The results obtained suggest the potential of the devised method in designing efficient active control systems for large flexible structures.

Baz, A.↗

NASA NTRS1988

Modified independent modal space control method for active control of flexible systems

Baz, A.↗

NASA NTRS1989

Modified independent modal space control method for active control of flexible systems

Baz, A.↗

NASA NTRS1993

A multi-zone muffle furnace design

A Multi-Zone Muffle-Tube Furnace was designed, built, and tested for the purpose of providing an in-house experience base with tubular furnaces for materials processing in microgravity. As such, it must not only provide the desired temperatures and controlled thermal gradients at several discrete zones along its length but must also be capable of sustaining the rigors of a Space Shuttle launch. The furnace is insulated to minimize radial and axial heat losses. It is contained in a water-cooled enclosure for purposes of dissipating un-wanted residual heat, keeping the outer surfaces of the furnace at a 'touch-safe' temperature, and providing a rugged housing. This report describes the salient features of the furnace, testing procedures and results, and concluding remarks evaluating the overall design.

Rowe, Neil D.↗