Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “finishing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

High level of integration of front-end imaging optics system for electron cyclotron emission imaging diagnostics on the DIII-D tokamak

The optics system of the Electron Cyclotron Emission Imaging (ECEI) diagnostics on the DIII-D tokamak has been developed and installed for high-resolution temperature fluctuations measurement in the previous decade. The System-on-Chip approach upgrade was finished in June 2019 with high integrated receiver array with 20 individual modules. In this paper, we design new optics with high-level integration. In the new optics system, there will be two mirrors from plasma to receiver array, including one replaceable curved mirror out of the vacuum and one fixed curved mirror in the vessel. There are two options with 1:1 and 1:2 magnifications for high poloidal resolution and larger poloidal window modes. Overall, the new optics system has multiple improvements, including lighter weight, smaller size, more flexible installation and alignment. The synthetic ECEI module is used to evaluate the new optics system.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Mechanical evaluation of WC-Co materials with varying microstructures

Tungsten carbide–cobalt materials are useful in a variety of extreme applications due to a desirable blend of properties, yet the technology has not significantly changed since their initial development in the 1920s. The mechanical properties of this class of materials is highly dependent on two variables, the size of the tungsten carbide grains, and the amount of binder phase present in the final body. In this study, the amount of binder phase is isolated across three commercial materials from the same manufacturer with three different grain sizes to investigate the effect on mechanical properties. The mechanical properties investigated are indentation hardness, flexure and tensile strength, as well as fracture toughness. In general, an increase in hardness and tensile strength with decreasing grain size was observed, while the fracture toughness showed the opposite trend with toughness increasing with increasing grain size. The flexure strength results did not show a correlation to grain size. Fractographic analysis identified the dominant strength-limiting flaw for each sample, which largely were in the form of porosity. Other flaws types, such as inclusions from the milling process, clusters of large grains, and machining cracks from the surface finishing process, were also identified. Finally, Weibull analysis was performed and deemed appropriate for analysis of these materials, but strength-size scaling was not conducted due to the variability in the strength-limiting feature between the different specimen geometries.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Water-induced surface ordering facilitating the microcutting of ductile metals

Metal cutting is a crucial process in modern manufacturing. Enhancing the machinability of metals can significantly improve their production efficiency and surface integrity. Coating surface-active media (SAM) on the free surface of the metals before cutting is an easy method to improve machinability, which usually pertains to the category of the renowned Rehbinder effect. However, the existing SAM is usually hazardous and complex materials. Besides, the effect of SAM on the local structure of the metal surface remains unclear. In this study, water is employed as a simple yet often overlooked SAM in the microcutting of copper. Using water as SAM also allows the employment of X-ray absorption fine structure spectroscopy (XAFS) to study the local structure of copper with and without water coating. Results show that water coating on the free surface of copper can significantly reduce the cutting force and chip thickness, and improve the surface finish. Interestingly, removing the water coating enables the recovery of the cutting force, demonstrating a reversible effect. Based on the XAFS results and molecular dynamics simulation, a water-induced surface ordering mechanism is proposed to explain the findings from the microcutting experiments. This mechanism suggests that water molecules can induce surface ordering in copper, resulting in reduced surface energy and fracture toughness of copper, thus enhancing machinability. In conclusion, this work provides valuable insights into the comprehension of the Rehbinder effect and shows that picometer-scale modifications of the surface atom arrangement can considerably alter the deformation mode of metals, paving the way for the development of new manufacturing processes.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Reactive flash sintering of TiZrN and TiAlN ternary metal nitrides

Here, this study demonstrated the reactive flash sintering (RFS) for two powder mixtures: TiN-ZrN (both conducting) and AlN-TiN (TiN conducting but AlN insulating), targeting ternary metal nitrides (TMN) of Ti 0.5 Zr 0.5 N and Ti 0.5 Al 0.5 N, respectively. A constant volage and pressure (e.g., 8 V DC, ∼15 MPa) at room temperature triggered the flash (current density up to 27 A/mm 2 ) without pre-heating, and the entire RFS process finished in a few minutes. For TiZrN, the flash was instantaneous whereas for TiAlN, there was a long incubation before the flash followed by a quick and dramatic flash. Both conventional ex situ XRD and in situ synchrotron study had been carried out. They showed a uniform Ti 0.57 Zr 0.43 N solution formed in RFS and persisted upon cooling, while (Ti, Al) N solid solution formed at high temperature was not stable and likely went through a very quick phase separation in the cooling process. The final products from RFS had been characterized using SEM/EDS for microstructure. Both TiZrN and TiAlN were dense. Distribution of Ti, Zr, and N was uniform for TiZrN; for TiAlN, Ti and N distribution was uniform, while association of Al with oxygen was observed. TGA-DSC revealed the onset oxidation temperature for TiZrN was comparable to TiN and ZrN, while it was higher by ∼200 °C for TiAlN, likely due to the formation of Al 2 O 3 . In terms of mechanical properties such as hardness or fracture toughness, forming a single-phase solid solution (like TiZrN) does not offer obvious benefits. while large grain size from RFS seemed to be unfavorable. Future optimization of RFS condition and in-depth study by both experiments and simulation are needed to fully understand the composition-processing-structure-property relationships for such TMN from the reactive flash sintering process.

Flash Sintering↗
DOE OSTI2023

Survey of the mechanical and physical behaviors of yttria-stabilized zirconia from multiple dental laboratories

Background: When selecting zirconia for a dental restoration, laboratory prescriptions often refer to high strength and high translucency. In this survey, zirconia specimens were ordered from various dental laboratories for posterior (high strength) and anterior (high translucency) clinical indications. The specimens were then tested and evaluated for their mechanical and physical behaviors. Methods: In a double-blinded manner, 9 laboratories provided 32 specimens from 17 different zirconia blanks, which were tested in the American Dental Association laboratory. Flexural strength tests were performed on standard specimens, and fracture surfaces were examined using both optical and scanning electron microscopy. Chemical composition, Vickers hardness, and absolute transmittance measurements were also performed. Results: A large scatter in the strength values was observed. The zirconia intended for posterior applications displayed strengths (SD) from 195 through 783 MPa (490 [183] MPa), which overlapped greatly with the strengths (SD) of the zirconia intended for anterior applications, 320 through 768 MPa (581 [136] MPa). However, when the strength values were recalculated on the basis of yttria content, the strengths (SD) were 584 (158) MPa for 3 mol% yttria and 373 (104) MPa for 5 mol% yttria. Conclusions: When a prescription was given to dental laboratories to request zirconia on the basis of clinical requirements, there was a large scatter and no consistency in the resulting strength values partly because of mixed use of 3 mol% and 5 mol% yttria zirconia. The 3 mol% materials had much higher strength when the strength values were grouped according to yttria content. Strength was also highly dependent on processing and finishing at the dental laboratories.

3 mol% yttria-tetragonal zirconia polycrystal (3Y-↗
DOE OSTI2020

Correlation approach for quality assurance of additive manufactured parts based on optical metrology

Surface topography and surface finish are two significant factors for evaluating the quality of products in additive manufacturing (AM). AM parts are fabricated layer by layer, which is quite different from traditional formative or subtractive methods. Despite rapid progress in additive manufacturing and associated optical metrology for quality control and in-situ monitoring, limited research has been conducted to investigate the reliability of 3D surface measurement data. The surface topologies scanned by multiple optical systems demonstrated significant differences due to varying sampling mechanisms, resolutions, system noises, etc. The 3D datasets should be trustworthy in order to extract parameters for quality assurance or feedback control from 3D surface measurements. In this paper, we set up new standards to evaluate the reliability of 3D surface measurement data and analyze the variation in the topographical profile. In this study, two non-contact optical methods based on Focus Variation Microscopy (FVM) and Structured Light System (SLS) were adopted to measure the surface topography of the target components. The two optical metrology systems generated two entirely different point cloud datasets. Statistical methods were applied to test the difference between the data obtained from the two systems. By using a data analytics approach for comparison, it was found that the surface roughness estimated from the point cloud data sets of FVM and SLS has no significant difference, though the point cloud data sets were completely different. This paper provides standard validation approach to evaluate the plausibility of metrology data from in-situ real-time surface analysis for process planning of AM.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Review of in situ process monitoring for metal hybrid directed energy deposition

Hybrid manufacturing, or the combination of additive and subtractive manufacturing within a single build volume is transforming the way products are being fabricated. Additive manufacturing confers unprecedented freedom of design and reduced material usage while enabling serial customization. Subtractive manufacturing provides superior surface finish and improved dimensional accuracies. Interwoven, these two digital manufacturing paradigms are enabling the rapid manufacturing of complex, highly accurate, and customized geometries in a diversity of high-performance alloys. In situ monitoring, heavily relied upon in either additive or subtractive, becomes even more crucial with the interplay of the two processes in a single combined build sequence. Moreover, challenges that do not exist in either process alone can now have a dramatic impact on final part quality: (1) a large amount of heat is generated during additive manufacturing deposition, which is primarily dissipated into the machine tooling and impacts accuracy by deforming the material and causing misaligned machining; (2) microstructure, mechanical properties, and residual stresses are the result of the complex thermal histories generated by additive manufacturing and can impact subsequent cutting performance. This comprehensive review considers previous research in monitoring and providing closed-loop control in both additive and subtractive manufacturing separately and then considers the implications of the effectiveness of these monitoring techniques when additive and subtractive processes are integrated together.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Enhanced joining strength in additive-manufactured polylactic-acid structures fused by embedded heated metallic meshes

Additively manufactured thermoplastic polymers, such as polylactic acid (PLA), hold significant promise for sustainable engineering structures, including wind turbine blades. Upscaling these structures beyond the limitations of 3D printer build volumes is a challenge; fusion joining presents a potential solution. This paper introduces a displacement-controlled resistance welding process for PLA, as an alternative to the typical force-controlled methods. Here, we investigated the bonding quality of resistance-welded and adhesive-bonded PLA beams through three-point bending and measured the surface deformations using digital image correlation. Different metal meshes (30%/0.11 mm Ni—Cu, 34%/0.07 mm Ni—Cu, and 36%/0.25 mm Co—Ni) served as heating elements. The process parameters were varied for the 34%/0.07 mm Ni—Cu mesh to identify an optimum set of parameters. Results showed that this optimized displacement-controlled welding achieved 94% of the original strength of monolithic samples. This indicates that the new welding process not only ensures high-quality bonding and fine surface finishing but also promotes sustainability, recyclability, and economic efficiency in various polymer and composite structural applications.

Additive manufacturing↗
DOE OSTI2024

Microstructure analysis and machinability of additively manufactured A205 aluminum with heat treatments

A205 aluminum is one of the few high-strength aluminum alloys discovered for additive manufacturing (AM). The microstructure and heat treatment effects of AM A205 vary from those of its cast form, indicating possible differences in machinability during post-processing. Here, the objective of this research is to determine these variations of AM A205 and their effects on machinability using the cast condition as the baseline. As built and two heat-treated conditions (solution treatment and age hardening) were applied and compared in terms of their microstructures, micro-hardness, and machinability including vibration, specific cutting energy, chip morphology, and surface finish. The effects of print orientations on machinability were tested as well and found to be insignificant. AM as built had a higher hardness and slightly better machinability than its cast as built cast counterpart due to a smaller grain size (1 µm vs. 15 µm), eutectic θ-Al 2 Cu lattice and a fine, homogeneous TiB 2 distribution. The solution treatment dissolved this θ-Al 2 Cu lattice and increased the grain size (3 µm) which decreased the hardness, increased the ductility seen in the chips, and reduced the overall machinability. The presence of θ’-Al 2 Cu precipitates improved the machinability of aged AM A205. In addition, it was found that A205 exhibited both ductile and brittle behavior depending on the cutting speed, thus producing different machinability. The speed dependency is related to the material condition and heat treatment.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Formation of functionally graded steel by laser powder bed fusion via in-situ carbon doping

Additive Manufacturing (AM) enables functional integration by combining multiple components into a single part to shorten assembly time, reduce weight, and improve performance. Laser Powder Bed Fusion (LPBF) is an important AM method due to excellent spatial resolution, surface finish, and material properties without the need for extensive post-processing. Functional integration could be enhanced by spatial tuning of properties, but LPBF cannot readily vary material composition. Here, this paper addresses a method to add spatial composition control by printing small quantities of dopants via liquid carrier prior to laser fusion. The impact of carbon black suspension added to select regions of a Stainless Steel 316 L powder bed on melt pool dimension, hardness, and porosity is reported. The distribution of the carbon between the doped and plain layers and the resulting spatial variation in hardness is measured. Optical microscopy and composition analysis show that the carbon dispersed uniformly within the layer of deposition and diffused as little as 50 μm in the build direction. Keyhole conditions dramatically increase the inter-layer transport of the dopant. The added carbon increased hardness by >50 %. Porosity increased in doped regions but remained below 1.5 % for the best processing parameters. These results demonstrate that the composition of LPBF parts could be controlled in 3-dimensions using a dopant that is soluble in the melt pool. Additional work will be required to evaluate different dopant materials and optimize processing conditions for full density, but microalloying with soluble dopants appears to be a plausible solution to enhance functional integration with LPBF.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Process-level cost analysis of hybrid manufacturing pathways for aerospace structural components

Hybrid manufacturing is a promising route for producing complex aerospace components, yet systematic cost benchmarking across multiple additive-subtractive pathways remains limited. This study presents a comprehensive process-based cost analysis of seven hybrid manufacturing routes, including laser powder bed fusion (L-PBF), powder- and wire-directed energy deposition (DED), wire arc additive manufacturing (WAAM), additive friction stir deposition (AFSD), metal binder jetting (MBJ), and agility forging, followed by scanning and finish machining. Parametric cost models incorporating direct material, labor, and energy costs were developed. L-PBF results are discussed in detail for a pickle fork component and directly compared with commercial pricing. Across all hybrid routes, labor emerged as the dominant cost driver, contributing more than 70% of total manufacturing cost in some cases. AFSD exhibited the lowest cost for aluminum components, with MBJ being its 316 L stainless steel counterpart, after accounting for geometric scaling. Benchmarking against industrial quotes suggests that hybrid manufacturing can achieve cost levels comparable to those of commercial services, although labor-intensive processes exhibit greater deviation. The analysis highlights automation of material handling, setup, and supervision as key opportunities for improving economic competitiveness. Overall, the proposed framework provides a quantitative basis for evaluating and optimizing hybrid manufacturing pathways for aerospace applications.

Baruah, Sweta [ORNL] (ORCID:0009000174256207)↗
DOE OSTI2026

Extended continuous cooling transformation diagram for 410 stainless steel encompassing δ → γ and γ → αʹ transformations determined by dilatometry

In this study, we use dilatometry to construct an extended Continuous Cooling Transformation (CCT) diagram for 410 stainless steel, capturing both δ → γ and γ → αʹ transformations specifically for directed energy deposition (DED) additive manufacturing (AM) applications. To ensure that the findings are representative of AM specific microstructures and compositions, dilatometry coupons were extracted from a wire arc DED wall, thereby preserving the inherent microstructural and compositional variability within the material. The on-heating phase transformations, including A c1 , A c3 , and γ → δ, were found to be essentially location independent, despite the typical heterogeneity associated with AM. Conversely, increasing cooling rates were observed to shift the start and finish temperatures of both δ → γ and γ → αʹ transformations to lower values. The resulting extended CCT diagram offers a more complete depiction of phase transformation behavior in the system, enabling accurate microstructure evolution modeling and residual stress predictions specifically for directed energy deposition additive manufacturing applications.

Additive manufacturing↗
DOE OSTI2022

Mechanical and Thermophysical properties of low enriched uranium-10wt% molybdenum rolled foils

In this study, low-enriched (~19.75% 235 U) U-10Mo(wt%) foils were evaluated for both mechanical and thermophysical properties to establish baseline characteristics prior to irradiation testing. Cast U-10Mo ingots were sequentially hot and cold rolled to two different final foil thicknesses, resulting in different levels of cold work being present in the finished foils. The mechanical response of the U-10Mo foils was evaluated in the temperature range of 293–623 K. Increasing test temperatures resulted in decreases of both yield and ultimate tensile strength. Comparison of results to earlier work performed on depleted U-10Mo rolled foils indicates that the material in this study has lower strength and increased ductility. However, a comparison of the two different foil thicknesses in this study found that they were nearly identical in yield and ultimate tensile strength, differing by only 10–20 MPa (<2%). Thermal conductivity was calculated from the measurements of specific heat, linear thermal expansion, and thermal diffusivity from 323 to 1273 K on both thicknesses of the foils. These data were approximately 5–10% lower than previously published data above 573 K and were similar to data for temperature ranges below 573 K. Differences are likely related to differences in grain size and/or impurity content and variation in fabrication history.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

Nanoindentation mapping defects filtration for heterogeneous materials using generative adversarial networks

Advanced composite materials with multiple phases and heterogeneous microstructure necessitate spatial mapping characterization of elastic modulus to develop constitutive relations and overall mechanical response. Such modulus mapping can be obtained using the nanoindentation technique, where the indenter tip raster over the selected microstructure region. Typically, a surface preparation procedure is done in the specimens to ensure proper contact between the indenter tip and sample surface. However, a near-perfect surface finish is unachievable in heterogeneous materials, primarily with ceramic reinforcements, due to the differential material removal rate during polishing. Thus, the nanoindenter records localized erroneous measurements due to differences in surface roughness and corresponding force response. This study establishes a novel deep learning-based strategy to rectify incorrect experimental spatial measurements acquire during nanoindentation modulus mapping. Here, the integrated bicubic interpolation and generative adversarial networks (GANs) model was trained using 14 ceramic and 18 metallic data sets, each comprising 65,536 measurements. The developed algorithm was validated against experimental measurements on four unknown specimens. The standard deviation in measured elastic modulus reduces by ~50% in ceramics and ~72% in metallic samples. This computational framework proposes a novel approach to reducing uncertainty in materials’ properties using state-of-the-art computer vision techniques.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Hybrid manufactured dynamometer for cutting force measurement

This paper describes a two-step (additive + subtractive) hybrid manufacturing approach for a laser powder bed fusion 316L stainless steel constrained-motion cutting force dynamometer (PBF CMD). The purpose of the research is to produce a near-net shape metallic dynamometer via additive manufacturing (AM) with post-processing by machining and wire-EDM to achieve the desired surface finish and performance. A cutting force comparison is presented with a commercially-available dynamometer.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Hybrid manufacturing of Invar mold for carbon fiber layup using structured light scanning

This paper describes coordinate system definition and transfer for five-axis machining of additively-manufactured preforms. In this method, a set of fiducials are attached to the temporarily attached to the part, and their location relative to the preform geometry is calibrated using a structured light scanner. Those fiducials can then be measured in the machine tool to determine the location and orientation of the part. The method is demonstrated by finish-machining a carbon fiber layup mold from an additively manufactured Invar preform. In addition to showing the coordinate transfer methods necessary to machine the part, several key challenges with machining additively-manufactured preforms are discussed and potential solutions are proposed. Unfortunately, the final part was ultimately unusable due to porosity inside the part left from the additive process. Future work will remanufacture this part while taking steps to avoid porosity and other challenges encountered.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A machining digital twin for hybrid manufacturing

Hybrid manufacturing consisting of metal additively manufactured preforms and computer numerical control (CNC) machining has been established to be an effective method for high material use rates. However, hybrid manufacturing introduces unique challenges. Near-net shape designs are typically selected, which result in a smaller margin for part placement within the stock and stringent requirements for work coordinate system identification. Additionally, less stock material reduces the preform stiffness, which limits the material removal rates during machining. This paper demonstrates a digital twin for CNC machining of a wire arc additively manufactured preform that implements: 1) structured light scanning for stock model identification and tool path generation; 2) a fused filament fabrication apparatus to attach temporary fiducials and scan targets to the preform that enable coordinate system definition for both the CAM and CNC machine; 3) preform and tool tip frequency response function measurements to enable stable milling parameter selection; and 4) post-manufacturing measurements of geometry, surface finish, and structural dynamics to confirm designer intent. These efforts define key components of the machining digital twin for hybrid manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Assessment of the grindability of robocast silicon carbide

The demand for high-performance lightweight optics has driven interest in silicon carbide (SiC) due to its exceptional thermal stability, hardness, and strength-to-weight ratio. This study investigates the potential of robocasting, an additive manufacturing process, as a viable method for producing lightweighted SiC components for optical applications. Four samples with varied starting powder phases (α and β) and sintering conditions were fabricated and evaluated. Post-sintering surface and form were assessed using coherence scanning interferometry (CSI) and coordinate measuring machine (CMM) techniques. A three-stage grinding process was applied to each sample, with surface roughness assessed at each stage. Results demonstrate that samples with predominantly α-phase SiC and smaller particle sizes achieved superior surface finish, particularly sample D2-α-2135 °C, which displayed the lowest post-grinding Sq value of 0.178 µm. The analysis also indicated no significant print-through effect from the lightweighting structure, or print artifacts, at this stage of grinding. However, β-phase samples showed poorer grindability, increased surface roughness, and pitting. These findings suggest that phase composition and particle size are critical for achieving the desired surface quality in robocast SiC optics. Future work will incorporate additional samples and finer grinding wheels to refine surface quality further, supporting the development of SiC for high-precision optical applications.

Barrett, Taylor [ORNL]↗