Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “energy efficient materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Critical Analysis of Replacements for R-410A in Heat Pump Applications

Using low-GWP refrigerants can reduce the Green House Gas (GHG) emission of HVAC systems. Research has shown that using heat exchangers with small diameter tubes is a promising solution to meet the performance goals of heat pump using low-GWP refrigerants due to reduced refrigerant charge, reduced flammable impact and environmental impact. However, application of small diameter tube requires in-depth component design optimization to make the new system adapt to low-GWP refrigerants.In this paper, multi-objective optimizations using Particle Swarm Optimization (PSO) algorithm on a R-410A residential 5-ton air source heat pump is performed for improved system performance and reduced material cost. Five R-410A alternatives, i.e., R-32, R-454A, R-454B, R-454C and R-455A are investigated. R-455A and R-454C have GWP lower than 150. As a result of optimization, 12.4%-19.1% Energy Efficiency Ratio (EER) improvement and up to 71% HXs material cost saving is achieved. Life Cycle Climate Performance (LCCP) analysis shows that optimized systems reduce total CO2 emission by 13%-33% depending on the choice of refrigerant and climate zone.The optimal heat exchangers resulting from this research can fit into the original R-410A fan-coil units. The proposed heat pump design method establishes a production and installation path to produce cost-effective low-GWP heat pumps easily accepted by end users.

Li, Zhenning↗
DOE OSTI2024

Additive Manufacturing of Thermal Energy Storage Composites with Microencapsulated Phase Change Materials Supported in a Multi-Polymer Matrix

Advanced manufacturing techniques, such as additive manufacturing (AM), that can directly integrate phase change materials (PCMs) have garnered interest in recent years due to their potential for development of highly efficient thermal energy storage architectures. Complex, high surface area geometries embedded with PCMs that are only feasible with AM can improve thermal management with reduced material waste. Our work focuses on developing composite filaments with microencapsulated phase change materials (MEPCM) bound within a single or dual polymer matrix that can be processed through standard filament extruders and additively manufactured using off-the-shelf 3D printers. Polymer powders, rather than polymer pellets, were key to homogenously mixed filaments achieving high MEPCM loadings with no deterioration in thermal energy storage (TES) capability during extrusion. Composite filaments contain upwards of 60 wt% MEPCM and were printed without loss in feature resolution, print speed, or layer adhesion. Storage enthalpies of printed composites range from 100 - 130 kJ/kg, which were within 5% of the theoretical enthalpy based on weight fraction of MEPCM and maintained enthalpies within 1% over 500 thermal cycles. We can reliably manufacture low density, high surface area structures like 15% gyroid infill, along with dense, compact pucks at a 100% concentric infill. Prints were also scalable to a 900 cm3 honeycomb infill heat exchanger model that has an estimated energy storage capacity of 9 Wh.

3D printing↗
DOE OSTI2021

Effects of Hydrogen Redistribution at High Temperatures in Yttrium Hydride Moderator Material

We report advanced materials development, manufacturing, and modeling capabilities for innovative reactor designs support nuclear security and mission-focused science through enhanced technology for safer and more efficient and secure production of nuclear energy. The high temperature moderator material yttrium hydride poses a significant enhancement in small reactor design by thermalizing (slowing down) neutrons and decreasing the required fuel mass for a system. The research presented here supports understanding hydrogen distribution in yttrium hydride through: (1) the development of neutron-based hydrogen imaging and crystallographic characterization that allows us to understand fundamental diffraction behaviors and to observe changes in hydrogen distribution as a function of temperature and (2) subsequent neutron multiplication (reactivity) effects of changes in hydrogen distribution using measurement-based cross sections in a sample microreactor design. The main conclusions from the work are that: (1) hydrogen does not redistribute significantly below temperatures of 800°C in yttrium hydride and (2) hydrogen redistribution affects the reactivity slightly but not significantly.

36 MATERIALS SCIENCE↗
DOE OSTI2020

3D printing of metal-based materials for renewable energy applications

Large-scale renewable energy must overcome conversion and storage challenges before it can replace fossil fuels due to its intermittent nature. However, current sustainable energy devices still suffer from high cost, low efficiency, and poor service life problems. Recently, porous metal-based materials have been widely used as desirable cross-functional platforms for electrochemical and photochemical energy systems for their unique electrical conductivity, catalytic activity, and chemical stability. To tailor the porosity length scale, ordering, and compositions, 3D printing has been applied as a disruptive manufacturing revolution to create complex architected components by directly joining sequential layers into designed structures. In conclusion, this article intends to summarize cutting-edge advances of metal-based materials for renewable energy devices (e.g., fuel cells, solar cells, supercapacitors, and batteries) over the past decade.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Understanding and Manipulating Counterion Condensation within Charged Polymer Electrolytes for Selective and Low Resistant Membrane Separations

Polymeric ion-exchange membranes are found at the heart of numerous electrochemical systems spanning separations (electrodialysis and membrane capacitive deionization) and energy conversion and storage (flow batteries, fuel cells, and electrolyzers). The ion-exchange membrane separators need to be ion conducting but electron insulating, and in many scenarios selective for a particular ion to conduct. Because of their polymeric nature, the molecular architectures of ion-exchange membranes lack the molecular precision found in many inorganic materials. Plus, they contain numerous structural defects that impede ionic transport. As a result of their poor structure, it has been difficult to carefully probe the underlying physics that governs ion transport in ion-exchange membranes. We investigated counterion condensation phenomena in ion-exchange membranes and correlated it to bulk ionic charge transport and selectivity in precisely defined and long-range ordered materials afforded through the principles of directed self-assembly. A multi-faceted approach spanning i.) advanced metrology, two-dimensional atomic force microscopy, x-ray scattering, and ion-exchange equilibria, and ii.) molecular simulations (classical molecular dynamics and ab-inito molecular dynamics) that bridge multiple time and length scales, were employed to correlate the extent of counterion condensation to ionic conductivity and selectivity. After uncovering the extent of the condensation phenomena in this project, new macromolecular chemistries were employed to manipulate the ion pairing interactions of the condensed counterions to tethered ions on the polymer backbone so more facile and selective conduction rates can be attained. The research has aided in the rational design of polymeric ion-exchange membrane separators with high current density for electrochemical systems and subsequently better energy efficiency.

36 MATERIALS SCIENCE↗
DOE OSTI2022

2,3-Diphenylthieno[3,4-b]pyrazines as Hole-Transporting Materials for Stable, High-Performance Perovskite Solar Cells

High-performance and durable perovskite solar cells (PSCs) have advanced rapidly, enabled in part by the development of superior interfacial hole-transporting layers (HTLs). Here, in this study, a new series of 2,3-diphenylthieno[3,4-b]pyrazine (DPTP)-based small molecules containing bis- and tetrakis-triphenyl amino donors (1–3) was synthesized from simple, low-cost, and readily available starting materials. The matched energy levels, ideal surface topographies, high hole mobilities of 8.57 × 10 –4 cm 2 V –1 S –1 , and stable chemical structures of DPTP-4D (3) make it an effective hole-transporting material, delivering a PCE of 20.18% with high environmental, thermal, and light-soaking stability when compared to the reference HTL materials, doped Spiro-OMeTAD and PTAA in PSC n-i-p planar devices. Overall, these DPTP-based molecules are promising HTM candidates for the fabrication of stable PSCs.

14 SOLAR ENERGY↗
DOE OSTI2024

Industrial Assessment Center

Established in 1990, San Diego State University’s (SDSU) Industrial Assessment Center (IAC) is proud of its years of service. During this period, it has served over 620 small and medium-sized manufacturing plants in Southern California. SDSU/IAC’s efforts to transfer state-of-the-art technologies to industry have increased revenues, cultivated creativity, improved energy efficiencies, and benefited the environment. The Center has contributed to the region's economic growth and stability by assisting small and medium size companies to better compete in the global market. It has helped mitigate climate change by reducing greenhouse gas emissions. IAC activities have fostered productive relationships between the University and local industry, assisted industrial sectors to improve their energy efficiency and enhance their manufacturing productivity, in turn impacting the material and working conditions of their employees. In addition to financial savings and environmental benefits, we have trained tens of students who became energy specialists in various companies. Thus, a substantial benefit of the IAC has been the ongoing training of engineering faculty and students. All IAC graduates were offered jobs before or within weeks of their graduation. The activities of the SDSU/IAC have expanded the institutional expertise of the College and improved the knowledge base of the faculties involved leading to several related publications, master’s theses, and senior student projects. Significant number of peer-reviewed publications of the IAC director at SDSU have greatly benefitted from the experience of the Center. As a result of this extensive exposure to manufacturing processes, the SDSU/IAC has grown to be an integral component of SDSU’s engineering research and training. We have successfully built upon these established achievements and academic excellence. IAC service to industry is particularly vital in Southern California, a region with one of the highest manufacturing concentrations in the country. SDSU/IAC has understood and implemented the overall objectives of DOE’s IAC program and guidelines except for the pandemic years when the country’s manufacturing sector was put in dire stress. In addition to student training and service to industry, IAC’s contribution to state and local governments as well as utility companies to assess energy policies and design rebate and incentive strategies cannot be undermined.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2021

Thermally Stable Single-Atom Heterogeneous Catalysts

Single-atom catalysts (SACs) have attracted extensive attention in fields related to energy, environment, and material sciences because of the high atom efficiency and the unique properties of these materials. Many approaches have hitherto been successfully established to prepare SACs, including impregnation, pyrolysis-involved processes, atom trapping, and coprecipitation. However, under typical reaction conditions, single atoms on catalysts tend to migrate or agglomerate, forming nanoclusters or nanoparticles, which lowers their surface free energy. Efforts are required to develop strategies for improving the thermal stability of SACs while achieving excellent catalytic performance. Here in this Progress Report, recent advances in the development of thermally durable single-atom heterogeneous catalysts are discussed. Several important preparation approaches for thermally stable SACs are described in this article. Fundamental understanding of the coordination structures of thermally stable single atom prepared by these methods is discussed. Furthermore, the catalytic performances of these thermally stable SACs are reviewed, including their activity and stability. Finally, a perspective of this important and rapidly evolving research field is provided.

coordination structure↗
NASA NTRS2015

Scintillating Quantum Dots for Imaging X-rays (SQDIX) for Aircraft Inspection

Scintillation is the process currently employed by conventional x-ray detectors to create x-ray images. Scintillating quantum dots or nano-crystals (StQDs) are a novel, nanometer-scale material that upon excitation by x-rays, re-emit the absorbed energy as visible light. StQDs theoretically have higher output efficiency than conventional scintillating materials and are more environmental friendly. This paper will present the characterization of several critical elements in the use of StQDs that have been performed along a path to the use of this technology in wide spread x-ray imaging. Initial work on the SQDIX system has shown great promise to create state-of-the-art sensors using StQDs as a sensor material. In addition, this work also demonstrates a high degree of promise using StQDs in microstructured fiber optics. Using the microstructured fiber as a light guide could greatly increase the capture efficiency a StQDs based imaging sensor.

Burke, Eric↗
NASA NTRS2015

Scintillating Quantum Dots for Imaging X-Rays (SQDIX) for Aircraft Inspection

Scintillation is the process currently employed by conventional X-ray detectors to create X-ray images. Scintillating quantum dots (StQDs) or nano-crystals are novel, nanometer-scale materials that upon excitation by X-rays, re-emit the absorbed energy as visible light. StQDs theoretically have higher output efficiency than conventional scintillating materials and are more environmentally friendly. This paper will present the characterization of several critical elements in the use of StQDs that have been performed along a path to the use of this technology in wide spread X-ray imaging. Initial work on the scintillating quantum dots for imaging X-rays (SQDIX) system has shown great promise to create state-of-the-art sensors using StQDs as a sensor material. In addition, this work also demonstrates a high degree of promise using StQDs in microstructured fiber optics. Using the microstructured fiber as a light guide could greatly increase the capture efficiency of a StQDs based imaging sensor.

Burke, E. R.↗
DOE OSTI2025

In situ synchrotron x-ray studies of epitaxial SrCoO x films during ionic liquid gating

The manipulation of ions in complex oxide materials can be used to mimic brain-like plasticity through changes to the resistivity of a neuromorphic device. Advances in the design of more energy efficient devices require improved understanding of how ions migrate within a material and across its interface. We investigate the exchange of oxygen and hydrogen in a model SrCoO x epitaxial film—a material that transitions between a ferromagnetic metal and antiferromagnetic insulator depending on the oxygen concentration. Changes to the film during ionic liquid gating were measured by in situ synchrotron x-ray techniques as a function of time and gate voltage, examining the reversibility of the oxide over one complete gating cycle. We find that the out-of-plane lattice constant and oxygen vacancy concentration of SrCoO x are largely reversible although changes were observed in the ordered vacancy structure. Our results provide much needed insight into electrolyte-gated phase behavior in the transition metal oxides.

Li, Yan [Argonne National Laboratory (ANL), Argonn↗
DOE OSTI2022

Chapter 10 - Thermal Energy Harvesting Using Thermomagnetic Effect

Low-grade thermal energy, either in the form of waste heat or nature heat, is available abundantly around us. Since Carnot efficiency reduces with decrease in operating temperature difference, there are very limited practical options for low-grade thermal energy conversion. Thermomagnetic effect is the effect of heat on magnetic properties of a material. This phenomenon can be used to generate electricity using either direct thermal to electrical energy conversion or indirect thermal to mechanical energy conversion. This chapter provides a broad overview of various aspects of thermomagnetic energy conversion. We first explain the working principle behind the thermomagnetic energy harvesting. We then formulate mathematical equations needed to calculate the work output and energy conversion efficiency of a thermomagnetic cycle. Based on this formulation, we provide a list of working materials that can be employed in the thermomagnetic harvesters. At last, we describe various thermomagnetic harvesters proposed in the literature.

ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATION↗
DOE OSTI2021

Polycrystalline SnSe with a thermoelectric figure of merit greater than the single crystal

Abstract Thermoelectric materials generate electric energy from waste heat, with conversion efficiency governed by the dimensionless figure of merit, ZT. Single-crystal tin selenide (SnSe) was discovered to exhibit a high ZT of roughly 2.2–2.6 at 913 K, but more practical and deployable polycrystal versions of the same compound suffer from much poorer overall ZT, thereby thwarting prospects for cost-effective lead-free thermoelectrics. The poor polycrystal bulk performance is attributed to traces of tin oxides covering the surface of SnSe powders, which increases thermal conductivity, reduces electrical conductivity and thereby reduces ZT. Here, we report that hole-doped SnSe polycrystalline samples with reagents carefully purified and tin oxides removed exhibit an ZT of roughly 3.1 at 783 K. Its lattice thermal conductivity is ultralow at roughly 0.07 W m –1 K –1 at 783 K, lower than the single crystals. The path to ultrahigh thermoelectric performance in polycrystalline samples is the proper removal of the deleterious thermally conductive oxides from the surface of SnSe grains. These results could open an era of high-performance practical thermoelectrics from this high-performance material.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Nanoengineering Porous Silica for Thermal Management

Thermal insulation of solid materials originates from the nanoscale porous architectures to regulate thermal management in energy-critical applications from energy-efficient buildings to heat-sensitive energy devices. Here, we show nanoengineering of porous silica materials to control the architecture transition from mesoporous to nanocage networks. A low thermal conductivity of such a porous silica network is achieved at 0.018 W/(m K) while exhibiting a porosity of 92.05%, specific surface area of 504 m 2 /g, and pore volume of 2.37 cm 3 /g after ambient pressure drying. Meanwhile, the crosslinking of the porous silica and ceramic fiber frameworks show a tensile Young’s modulus of 2.8 MPa while maintaining high thermal insulation, which provides an effective thermal runway mitigation strategy for rechargeable lithium-ion batteries. Furthermore, the nanoengineering strategy reported here would shed light on achieving superthermal insulation of nanostructures for energy-critical applications.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Synergistic cellulase–xylanase formulations for enhanced dewatering and fiber bonding toward energy-efficient and sustainable paper and packaging production

A mechanistic understanding of the synergistic effects of enzymes on cellulosic fibers dewatering and fiber bonding is essential for advancing energy-efficiency and lightweight production of paper and packaging materials. This study investigates the impact of varying cellulase and xylanase formulations on equilibrium moisture content (EMC) after pressing and tensile strength of cellulosic fiber webs using a factorial experimental design. Nine custom enzyme formulations were evaluated at controlled dosages ranging from ∼20 to 76 FPU/mL cellulase and ∼500–1130 IU/mL xylanase. Response surface modeling revealed a significant synergy, particularly at 20–40 FPU/mL cellulase combined with ≥ 1000 IU/mL xylanase. Under these conditions, EMC decreased by up to 3.6% compared with the untreated refined control, while tensile index gains of up to 16% were statistically significant for optimized blends (p < 0.05). The interaction between cellulase and xylanase was also significant for the tensile response (p = 0.010). Protein efficiency analysis showed that optimized formulations containing 30–40% less protein outperformed the commercial benchmark. The nonlinear synergy between cellulase and xylanase is attributed to their complementary substrate specificities. Endoglucanase- and β‑glucosidase‑rich cellulases hydrolyze internal β‑1,4‑glycosidic bonds in amorphous cellulose, loosening fiber walls and increasing flexibility, while xylanases target hemicellulose, primarily xylan-rich domains, enhancing porosity and improve cellulase accessibility. Tailoring enzyme formulations at low loadings overcomes traditional trade-offs between strength and dewatering, enabling cost-effective, energy-efficient, low-carbon solutions for sustainable packaging and hygiene products.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Colossal switchable photocurrents in topological Janus transition metal dichalcogenides

Nonlinear optical properties, such as bulk photovoltaic effects, possess great potential in energy harvesting, photodetection, rectification, etc. To enable efficient light–current conversion, materials with strong photo-responsivity are highly desirable. In this work, we predict that monolayer Janus transition metal dichalcogenides (JTMDs) in the 1T' phase possess colossal nonlinear photoconductivity owing to their topological band mixing, strong inversion symmetry breaking, and small electronic bandgap. 1T'JTMDs have inverted bandgaps on the order of 10 meV and are exceptionally responsive to light in the terahertz (THz) range. By first-principles calculations, we reveal that 1T' JTMDs possess shift current (SC) conductivity as large as 2300 nm μA V -2 , equivalent to a photo-responsivity of 2800 mA/W. The circular current (CC) conductivity of 1T' JTMDs is as large as ~10 4 nm μA V -2 . These remarkable photo-responsivities indicate that the 1T' JTMDs can serve as efficient photodetectors in the THz range. We also find that external stimuli such as the in-plane strain and out-of-plane electric field can induce topological phase transitions in 1T' JTMDs and that the SC can abruptly flip their directions. The abrupt change of the nonlinear photocurrent can be used to characterize the topological transition and has potential applications in 2D optomechanics and nonlinear optoelectronics.

Chemistry↗
DOE OSTI2025

Tailoring Nitinol for elastocaloric application

This study focuses on tailoring commercial Nitinol, the most commonly used elastocaloric material, for near-room-temperature cooling applications. Short heat treatments near 500 °C were used to fine-tune the material’s transition temperature, resulting in austenite finish temperatures ranging from 6.0 to 25.5°C and altered superelastic and elastocaloric properties. Plateau stresses decreased while temperature changes rose from 21.5°C up to 27.9°C at 6% strain. Significant variability in the Nitinol response when testing below its austenite finish temperature was observed. In conclusion, the effect of mechanical cycling on transition temperatures was also evaluated, demonstrating an increase for all the samples.

Efficiency↗
DOE OSTI2021

Increasing melt efficiency and secondary alloy usage in aluminum die casting

In this project, the focus was to develop thermodynamic and kinetic models for the aluminum melting process involving secondary alloys, refractory materials and flux materials. The major research outcome of this study is 1) the refractory composition of CaO (8-12%), microsilica (1-3%), BaSO 4 and/or BaO (no more than 5%), B 2 O 3 (5%) and Al 2 O 3 (balance) effectively reduced the reactions with liquid Al and alloying/impurity elements and heat transfer during melting and holding process. 2) a flux composition of NaCl-KCl-(1-10%)KAlF 4 exhibited an effective covering effect and prevented the dross formation during melting of Al process. 3) A high Fe (0.44%) content recycled Al alloy with compatible mechanical properties was developed based on the impurities control methods, which provides great potential to replace the commercial structural alloys from primary Al and increase the usage of secondary alloys.

36 MATERIALS SCIENCE↗