SEARCH · Engineering Papers

Results for “thermal diffusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

All sources NASA NTRS DOE OSTI

DOE OSTI2021

Direct numerical simulation of single-species and binary-species boundary layers at high pressure

Direct numerical simulations of single-species and binary-species temporal boundary layers at high pressure are performed. The main objective is to investigate flow physics in a binary-species boundary layer at high pressure, with special attention to mass diffusion. The working fluids are nitrogen in the single-species cases, and a mixture of nitrogen and methane in the binary-species cases. An investigation of mean profiles shows that velocity and temperature profiles have steep gradients near the wall, whereas the mass fraction profiles do not have a steep gradient. This result indicates that the similarity law between velocity, temperature and mass fraction does not hold true in the binary-species boundary layer. The comparison of turbulent fluctuations shows that the qualitative characteristics of velocity and temperature are similar to each other. In contrast, profiles of mass fraction fluctuations are largely different from those of velocity and temperature. This result indicates that mass diffusion is not similar to momentum and thermal diffusions in binary-species boundary layers.

Toki, Takahiko↗

NASA NTRS1986

Heat capacity, enthalpy of mixing, and thermal conductivity of Hg(1-x)Cd(x)Te pseudobinary melts

Heat capacity and enthalpy of mixing of Hg(1-x)Cd(x)Te pseudobinary melts were calculated assuming an associated solution model for the liquid phase. The thermal conductivity of the pseudobinary melts for x = 0, 0.05, 0.1, and 0.2 was then calculated from the heat capacity values and the experimental values of thermal diffusivity and density for these melts. The thermal conductivity for the pseudobinary solid solution is also discussed.

Su, Ching-Hua↗

DOE OSTI2021

A Computational Study of the Thermodynamic Conditions Leading to Autoignition in Nanosecond Pulsed Discharges

Nanosecond pulsed discharges have attracted the attention of engine manufacturers due to the possibility of attaining distributed ignition sites that accelerate burn rates while resulting in very little electrode erosion. Multidimensional modeling tools currently capture the electrical structure of such discharges accurately, but resolving the chemical structure remains a challenging problem owing to the disparity of time-scales in streamer propagation (nanoseconds) and ignition phenomena (microseconds). The purpose of this study is to extend multidimensional results toward resolving the chemical structure in the wake of streamers (or the afterglow) by using a batch reactor model (BRM). This can afford the use of very detailed chemical kinetic information. The full nonequilibrium nature of the electrons is taken into account, along with fast gas heating, shock wave propagation, and thermal diffusion. The results shed light on ignition phenomena brought about by such discharges.

42 ENGINEERING↗

NASA NTRS1990

Near-limit flame structures at low Lewis number

The characteristics of premixed gas flames in mixtures with low Lewis numbers near flammability limits were studied experimentally using a low-gravity environment to reduce buoyant convection. The behavior of such flames was found to be dominated by diffusive-thermal instabilities. For sufficiently reactive mixtures, cellular structures resulting from these instabilities were observed and found to spawn new cells in regular patterns. For less reactive mixtures, cells formed shortly after ignition but did not spawn new cells; instead these cells evolved into a flame structure composed of stationary, apparently stable spherical flamelets. Experimental observations are found to be in qualitative agreement with elementary analytical models based on the interaction of heat release due to chemical reaction, differential diffusion of thermal energy and mass, flame front curvature, and volumetric heat losses due to gas and/or soot radiation.

Ronney, Paul D.↗

NASA NTRS1989

A study of the propagation, dynamics, and extinguishment of cellular flames using microgravity techniques

The characteristics of premixed gas flames in mixtures with low Lewis numbers, free of natural convection effects, were investigated and found to be dominated by diffusive-thermal instabilities. For sufficiently reactive mixtures, cellular structures resulting from these instabilities were observed and found to spawn new cells in regular patterns. For less reactive mixtures, cells formed shortly after ignition but did not spawn new cells; instead these cells evolved into a flame structure composed of stationary, apparently stable spherical flamelets. As a result of these phenomena, well-defined flammability limits were not observed. The experimental results are found to be in qualitative agreement with a simple analytical model based on the interaction of heat release due to chemical reaction, differential diffusion of thermal energy and mass, flame front curvature, and heat losses due to gas radiation.

Ronney, Paul D.↗

DOE OSTI2022

Towards performing high-resolution inelastic X-ray scattering measurements at hard X-ray free-electron lasers coupled with energetic laser drivers

High-resolution inelastic X-ray scattering is an established technique in the synchrotron community, used to investigate collective low-frequency responses of materials. When fielded at hard X-ray free-electron lasers (XFELs) and combined with high-intensity laser drivers, it becomes a promising technique for investigating matter at high temperatures and high pressures. This technique gives access to important thermodynamic properties of matter at extreme conditions, such as temperature, material sound speed, and viscosity. The successful realization of this method requires the acquisition of many identical laser-pump/X-ray-probe shots, allowing the collection of a sufficient number of photons necessary to perform quantitative analyses. Here, a 2.5-fold improvement in the energy resolution of the instrument relative to previous works at the Matter in Extreme Conditions (MEC) endstation, Linac Coherent Light Source (LCLS), and the High Energy Density (HED) instrument, European XFEL, is presented. Some aspects of the experimental design that are essential for improving the number of photons detected in each X-ray shot, making such measurements feasible, are discussed. A careful choice of the energy resolution, the X-ray beam mode provided by the XFEL, and the position of the analysers used in such experiments can provide a more than ten-fold improvement in the photometrics. The discussion is supported by experimental data on 10 µm-thick iron and 50 nm-thick gold samples collected at the MEC endstation at the LCLS, and by complementary ray-tracing simulations coupled with thermal diffuse scattering calculations.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Faster ablative Kelvin–Helmholtz instability growth in a magnetic field

Shear flows along a plasma interface will quickly grow unstable due to the Kelvin–Helmholtz instability. If there is a concurrent temperature gradient across the interface, higher modes are stabilized by the thermal diffusion. These ablative effects must be considered in, for example, jet features in inertial confinement fusion hot-spots, or plasma plumes in young supernovae. We show that magnetization of the plasma can greatly affect the instability, even if magnetic pressure is small. This is because electrons are localized by their gyromotion, reducing the heat flux and material ablation. We use a two-dimensional numerical extended-magnetohydrodynamics approach to assess this effect for dense fusion conditions. In comparison with the unmagnetized case, self-generated Biermann fields make only a minor difference to growth rates. However, simulations with a large 50 kT external field found that the growth rate of the least stable mode increased by 40%. In conclusion, this has implications for mix processes in Z-pinches and magnetized inertial confinement fusion concepts.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2020

Preliminary Reporting of Thermophysical Property Measurements for the Ghareb Formation

Accurate knowledge of thermophysical properties of rock is vital to develop meaningful models of high level nuclear waste emplacement scenarios. The Israel Atomic Energy Commission is considering storing high level nuclear waste in the Ghareb formation, a porous kerogen bearing chalk. Sandia is supporting this effort with an evolving lab- based geomechanics testing program. We have completed measurements of thermal properties up to 275C and room temperature hydrostatic compaction measurements. We report thermal conductivity, thermal diffusivity, specific heat, and mass loss from our thermal measurements, and we report bulk moduli and porosity loss from our compaction measurements. These values are crucial for the numerical models to simulate heat transfer and formation compressibility around a heat generating repository.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2021

Mechanical and Thermophysical Properties of 3D-Printed SiC before and after Neutron Irradiation – FY21

This report presents the mechanical and thermophysical properties of 3D-printed SiC before and after neutron irradiation that have been evaluated to assess the fuel matrix material for the Transformational Challenge Reactor (TCR). The TCR fuel form consists of an additively-manufactured silicon carbide (SiC) matrix and uranium nitride tristructural isotropic (UN TRISO) fuel particles, which is manufactured through a newly developed processing route combining binderjet 3D printing, TRISO fuel particle loading, and chemical vapor infiltration (CVI). Because the fuel matrix is a primary component of the TCR core and its response to mechanical and thermal loads during operation is one of the most influential factors on the integrity of TCR core, testing and evaluation have focused on producing mechanical and thermophysical properties data for the binderjet/CVI SiC. Baseline mechanical and thermophysical properties were measured from the disk specimens printed for different and sizes orientations, which included equibiaxial flexural failure strength, elastic constants, thermal diffusivity and conductivity, density, and the coefficient of thermal expansion. Flexural failure strength datasets showed similar Weibull distributions regardless of sample variants including different orientations. The mean failure strengths of the 3D-printed SiC variants were in the range of 280–310 MPa, which are slightly lower than that of the chemical vapor deposition (CVD) SiC. Thermophysical test results showed that specific heat and thermal expansion are not sensitive to the build direction of SiC samples, while thermal conductivity is highly dependent on the build direction and can be correlated to the anisotropic character of the 3D-printed SiC. Neutron irradiation tests were carried out on the 3D-printed 6-mm diameter SiC disk specimens. Irradiation was carried to 2.3 dpa over a temperature range of 360–880°C. No significant degradation in strength was observed in SiC after irradiations in various conditions and with different orientations. Anisotropy that had been observed in the thermal conductivity of 3D-printed SiC prior to irradiation vanished after irradiation as the irradiation defect thermal resistivity accumulated in the material. Electron microscopy of the microstructure after neutron irradiation showed distinct defect morphologies in the heterogenous material, but no evidence for irradiation-induced cracking or degradation in the microstructure was observed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

NASA NTRS1972

Method of simultaneous measurement of radiative and lattice thermal conductivity.

A new technique of high-temperature thermal-conductivity measurement is described. A CO2 gas laser is used to generate a low-frequency temperature wave at one face of a small disk-shaped sample, and an infrared detector views the opposite face to detect the phase of the emerging radiation. A mathematical expression is derived which enables phase data at several frequencies to be used for the simultaneous determination of thermal diffusivity and mean extinction coefficient. Lattice and radiative thermal conductivities are then calculated. Test results for sintered aluminum oxide at temperatures from 530 to 1924 K are within the range of error of previously existing data.

Schatz, J. F.↗

NASA NTRS1995

Finite Element Analysis of Poroelastic Composites Undergoing Thermal and Gas Diffusion

A theory for time-dependent thermal and gas diffusion in mechanically time-rate-independent anisotropic poroelastic composites has been developed. This theory advances previous work by the latter two authors by providing for critical transverse shear through a three-dimensional axisymmetric formulation and using it in a new hypothesis for determining the Biot fluid pressure-solid stress coupling factor. The derived governing equations couple material deformation with temperature and internal pore pressure and more strongly couple gas diffusion and heat transfer than the previous theory. Hence the theory accounts for the interactions between conductive heat transfer in the porous body and convective heat carried by the mass flux through the pores. The Bubnov Galerkin finite element method is applied to the governing equations to transform them into a semidiscrete finite element system. A numerical procedure is developed to solve the coupled equations in the space and time domains. The method is used to simulate two high temperature tests involving thermal-chemical decomposition of carbon-phenolic composites. In comparison with measured data, the results are accurate. Moreover unlike previous work, for a single set of poroelastic parameters, they are consistent with two measurements in a restrained thermal growth test.

Salamon, N. J.↗

NASA NTRS1972

Transport properties of gases and binary liquids near the critical point

A status report is presented on the anomalies observed in the behavior of transport properties near the critical point of gases and binary liquids. The shear viscosity exhibits a weak singularity near the critical point. An analysis is made of the experimental data for those transport properties, thermal conductivity and thermal diffusivity near the gas-liquid critical point and binary diffusion coefficient near the critical mixing point, that determine the critical slowing down of the thermodynamic fluctuations in the order parameter. The asymptotic behavior of the thermal conductivity appears to be closely related to the asymptotic behavior of the correlation length. The experimental data for the thermal conductivity and diffusivity are shown to be in substantial agreement with current theoretical predictions.

Sengers, J. V.↗

NASA NTRS1989

Accurate determination of specific heat at high temperatures using the flash diffusivity method

The flash diffusivity method of Parker et al. (1961) was used to measure accurately the specific heat of test samples simultaneously with thermal diffusivity, thus obtaining the thermal conductivity of these materials directly. The accuracy of data obtained on two types of materials (n-type silicon-germanium alloys and niobium), was + or - 3 percent. It is shown that the method is applicable up to at least 1300 K.

Vandersande, J. W.↗

DOE OSTI2021

Projecting Permafrost Thaw of Sub-Arctic Tundra With a Thermodynamic Model Calibrated to Site Measurements

Northern circumpolar permafrost thaw affects global carbon cycling, as large amounts of stored soil carbon becomes accessible to microbial breakdown under a warming climate. The magnitude of carbon release is linked to the extent of permafrost thaw, which is locally variable and controlled by soil thermodynamics. Soil thermodynamic properties, such as thermal diffusivity, govern the reactivity of the soil-atmosphere thermal gradient, and are controlled by soil composition and drainage. In order to project permafrost thaw for an Alaskan tundra experimental site, we used seven years of site data to calibrate a soil thermodynamic model using a data assimilation technique. The model reproduced seasonal and interannual temperature dynamics for shallow (5–40 cm) and deep soil layers (2–4 m), and simulations of seasonal thaw depth closely matched observed data. The model was then used to project permafrost thaw at the site to the year 2100 using climate forcing data for three future climate scenarios (RCP 4.5, 6.0, and 8.5). Minimal permafrost thawing occurred until mean annual air temperatures rose above the freezing point, after which we measured over a 1 m increase in thaw depth for every 1 °C rise in mean annual air temperature. Under no projected warming scenario was permafrost remaining in the upper 3 m of soil by 2100. We demonstrated an effective data assimilation method that optimizes parameterization of a soil thermodynamic model. The sensitivity of local permafrost to climate warming illustrates the vulnerability of sub-Arctic tundra ecosystems to significant and rapid soil thawing.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2020

Tape casting and characterizations of MgO ceramics

Herein we report a high density MgO ceramic substrate produced by the tape casting technology. The tape casting formulation and process produced a uniform tape free of cracking. Y 2 O 3 and SiO 2 were used as the sintering aid for the pressureless sintering of the green tape. X-ray diffraction phase identification indicates that MgO is the main phase, while both Y 2 O 3 and SiO 2 sintering aids react with MgO to form MgY 4 Si 3 O 13 as the second phase. Liquid phase sintering occurs in the temperature range from 1030°C to ~1500°C, which is confirmed by the simultaneous Thermal Gravitation Analysis/ Differential Scanning Calorimeter (TGA/DSC) and the percent linear shrinkage and densification. A 96.5% theoretical density was achieved by presureless sintering at 1650°C for 2 hours, which was further increased to a fully dense structure using hotisostatic- pressing(HIP) at 1650°C and 207 MPa in argon. Scanning electron microscopy (SEM) and energy dispersive(EDS) spectroscopic analysis on the HIP’ed sample show that MgY 4 Si 3 O 13 is located at the MgO grain boundary and the sample has a fully dense structure. The refractive indices and extinction coefficient were measured on the HIP’ed sample along with thermal properties and dielectric properties. Thermal diffusivity and heat capacity were measured to calculate the thermal conductivity.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Infrared thermography NDT for in-situ defect detection in sandwich composite panel manufacturing

Composite manufacturing presents numerous challenges, as defects can arise from various sources throughout the process. In sandwich composite structures, the integration of a foam core introduces additional complexity and increases the likelihood of defect formation like delamination. To mitigate these issues and reduce the risk of future structural failures, in-situ monitoring during manufacturing is essential. This study investigates infrared (IR) thermography as a non-destructive technique for detecting manufacturing defects in foam-core sandwich composite panels under thermally excited conditions representative of in-situ processing. A stationary FLIR A8590 IR camera (640 × 512 pixels, 30Hz, 17mm lens, 9 ft stand-off distance) was used to monitor prefabricated panels subjected to controlled external heating simulating compression molding and resin cure exotherm. Interlaminar delamination defects with characteristic sizes ranging from 0.25 × 0.25in² to 5 × 5in² produced measurable surface temperature depressions of approximately 4–10°C during transient cooling, exceeding the effective noise floor of the camera by more than two standard deviations. Thicker laminates exhibited prolonged defect detectability windows due to increased thermal diffusion time. In contrast, embedded Teflon inclusions generated weak thermal contrasts of ≤ 3°C, approaching the measurement noise floor, due to limited thermal property contrast with the surrounding glass fiber composite. These results establish quantitative detectability limits for stationary thermographic inspection of sandwich composite panels under manufacturing-representative thermal cycles.

Barakat, Abdallah [ORNL] (ORCID:0000000296141398)↗

DOE OSTI2024

Investigation of core transport changes in DIII-D discharges with off-axis T e profile peaks

Abstract DIII-D discharges that transition to H-mode solely with off-axis electron cyclotron heating (ECH) often exhibit strong off-axis peaking of electron temperature profiles at the heating location. Electron heat transport properties near these off-axis temperature peaks have been studied using modulated ECH. The Fourier analyzed electron temperature data have been used to infer electron thermal diffusivity. Comparisons with numerical solutions of the time-dependent electron thermal equation find that the data are consistent with a narrow region with electron diffusivity χ e an order of magnitude lower than the average value across the plasma, suggesting an electron internal transport barrier (ITB) near the ECH heating location. Detailed profile analysis and equilibrium reconstructions suggest that the formation of these ITBs are correlated with off-axis values of the safety factor q being near 1. Furthermore, the ECH driven H-mode discharges demonstrate more rapid electron heating rate near the ECH deposition location than L-mode discharges with higher auxiliary ECH heating power. Additional modeling attributes this difference to the modification of electron heat transport in the core at the L-H transition, which also sustains the off-axis electron temperature peaks.

Physics↗

NASA NTRS1990

Collision integrals and high temperature transport properties for N-N, O-O, and N-O

Accurate collision integrals for the interactions of N(4S0) + N(4S0), O(3P) + O(3P), and N(4S0) + O(3P) are reported. These are computed from a semiclassical formulation of the scattering using the best available representations of all of the potential energy curves needed to describe the collisions. Spectroscopic curves and other accurate measured data are used where available; the results of accurate ab initio electronic structure calculations are used to determine the remaining potential curves. The high-lying states are found to give the largest contributions to the collision cross sections. The nine collision integrals needed to determine transport properties to second order are tabulated for translational temperatures in the range 250-100,000 K. The viscosity, thermal conductivity, diffusion coefficient, and thermal diffusion factor for a gas composed of nitrogen and oxygen atoms in thermal equilibrium have been calculated. It is found that the second-order contribution to the transport properties is small. Graphs of these transport properties for various mixture ratios are presented for temperatures in the range 5000-15,000 K.

Levin, E.↗