Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “shock sensitivity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

GALEX detection of shock breakout in type IIP supernova PS1-13arp: Implications for the progenitor STAR wind

We present the GALEX detection of a UV burst at the time of explosion of an optically normal supernova (SN) IIP (PS1-13arp) from the Pan-STARRS1 survey at z = 0.1665. The temperature and luminosity of the UV burst match the theoretical predictions for shock breakout in a red supergiant (RSG), but with a duration a factor of ∼50 longer than expected. We compare the NUV light curve of PS1-13arp to previous GALEX detections of SNe IIP and find clear distinctions that indicate that the UV emission is powered by shock breakout, and not by the subsequent cooling envelope emission previously detected in these systems. We interpret the ∼1 day duration of the UV signal with a shock breakout in the wind of an RSG with a pre-explosion mass-loss rate of ∼10{sup −3} M{sub ⊙} yr{sup −1}. This mass-loss rate is enough to prolong the duration of the shock breakout signal, but not enough to produce an excess in the optical plateau light curve or narrow emission lines powered by circumstellar interaction. This detection of non-standard, potentially episodic high mass loss in an RSG SN progenitor has favorable consequences for the prospects of future wide-field UV surveys to detect shock breakout directly in these systems, and provide a sensitive probe of the pre-explosion conditions of SN progenitors.

79 ASTRONOMY AND ASTROPHYSICS↗

Asperity generation and its relationship to seismicity on a planar fault: A laboratory simulation

Earthquake faults, and all frictional surfaces, establish contact through asperities. A detailed knowledge of how asperities form will enable a better understanding of the manner in which they communicate during foreshock failure sequences that are observed, leading to the larger main shock. We present results of experiments where a pressure sensitive film was used to map, size and measure the magnitudes of the normal stresses at asperities along a seismogenic section of a laboratory simulated fault. We measured seismicity acoustically and foreshocks were found to be the result of localized asperity failure during the nucleation phase of gross fault rupture. Since surface roughness plays an important role in how asperities are formed, two Hurst exponents were measured to characterize a highly worn interface using roughness profiles: (i) long wavelength estimates (H ~ 0.45) and (ii) short wavelength estimates (H ~ 0.8-1.2). The short wavelength roughness estimates were computed at the scale of single asperity junction points. Macroscopically, the number of asperities and real contact area increased with additional application of normal force while the mean normal stress remained constant. The ratio of real to nominal contact area was low - ranging from 0.02 < A r /A 0 < 0.05-predicting that the asperities should be elastically independent of each other. Results from the pressure sensitive film showed that asperities were closely spaced and could not be treated as mechanically independent. Larger asperities carried both higher levels of average normal stress and higher levels of normal stress heterogeneity than smaller ones. Using linear stability theorem, the critical slip distance on foreshocking asperities was estimated to be d 0 ~ 0.65-3 μm. The critical slip distance d 0 was ~1.8-11.5 per cent of the premonitory slip needed to initiate gross fault rupture of the interface (20-40 μm) and the overall slip necessary to initiate gross fault rupture was on the order of the average asperity diameter (52 μm). In conclusion, foreshocks may be due to a change in the critical slip distance, at localized sections of the fault, caused by the two distinct roughness profiles measured at short and long length scales.

58 GEOSCIENCES↗

Novel Hot-Spot Ignition Designs for Inertial Confinement Fusion with Liquid-Deuterium-Tritium Spheres

A new class of ignition designs is proposed for inertial confinement fusion (ICF) experiments. These designs are based on the hot-spot-ignition approach, but instead of conventional targets that comprise of spherical shells with thin frozen deuterium{tritium (DT) layers, homogeneous-density (solid or liquid) DT spheres are used where the lower-density central region and higher-density shell are created dynamically by appropriately shaping the laser pulse. These offer several advantages, including simplicity in target production and lower sensitivity to both laser imprint and physics uncertainty in shock interaction with the ice-vapor interface. The design evolution starts by launching an ~1-Mbar shock into a homogeneous DT sphere. After bouncing from the center, the reflected shock reaches the outer surface of the sphere and the shocked material starts to expand outward until its pressure drops below the ablation pressure. At this point, an adjustment shock is launched inward by supporting ablation pressure. This shock compresses the ablator and fuel, forming a shell. The shell is then accelerated and compressed by appropriately shaping the drive laser pulse, similar to the conventional thin-shell, hot-spot designs. Here, this paper demonstrates the feasibility of the new concept using hydrodynamic simulations and discusses the advantages and disadvantages of the concept compared with more-traditional ICF designs.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Highly linear, sensitive analog-to-digital converter

Analog-to-digital converter converts 10 volt full scale input signal into 13 bit digital output. Advantages include high sensitivity, linearity, low quantitizing error, high resistance to mechanical shock and vibration loads, and temporary data storage capabilities.

Cox, J.↗

Evaluation of boundary layer transition criteria for space shuttle orbiter entry

A comparison was made of the effect of boundary layer transition on center-line heating in a conical and a normal-shock flow field. It was shown that the time of transition onset (and, hence, the heating parameter) is significantly influenced by the choice of transition criterion in the normal-shock flow but that this parameter is much less sensitive to the transition criterion in a conical flow field. An evaluation of the effects of boundary layer transition on center-line heating in the conical flow field has shown that the temperatures are less affected by the use of various transition crieria than are heat loads. This difference is due to the delay in the time of transition onset predicted by those criteria with high transition Reynolds numbers. The criteria which predict the most severe thermal environment are those of fully turbulent flow throughout the entry, because transition occurs early in the trajectory for each of these criteria, they tend to predict similar values of maximum temperature and total heat load especially at center-line locations aft of 0.6. Evaluation of center-line heating generated by various trajectory shaping approaches has shown that the maximum surface temperature distribution was not significantly affected by the shaping technique. However, the heat load distribution is influenced, particularly on the forward portion of the vehicle.

Helms, V. T., III↗

A high frequency silicon pressure sensor

Theoretical and design considerations as well as fabrication and experimental work involved in the development of high-frequency silicon pressure sensors with an ultra-small diaphragm are discussed. A sensor is presented with a rectangular diaphragm of 0.0127 cm x 0.0254 cm x 1.06 micron; the sensor has a natural frequency of 625 kHz and a sensitivity of 0.82 mv/v-psi. High-frequency results from shock tube testing and low-frequency (less than 50 kHz) comparison with microphones are given.

Kahng, S. K.↗

Thermoluminescence and the shock and reheating history of meteorites. III - The shergottites

Thermoluminescence (TL) measurements on Shergotty, ALHA 77005, Zagami, and EETA 79001 (lithology A) have been used to obtain further information on the shock history of these meteorites. The level of TL sensitivity in the shergottites varied by a factor of 10, but was always low, probably reflecting the amount of crystalline material in the maskelynite. There are trends in the TL peak temperature, peak width, and TL sensitivity which are believed to be associated with different proportions of feldspar in high- and low-temperature forms. This interpretation is consistent with the observed changes induced in the TL properties by annealing shergottites at 400-900 C. It is suggested that the observed trends were produced during postshock crystallization at a variety of cooling rates, the increasing order of cooling rate being EETA 79001, Zagami, ALHA 77005, and Shergotty, and that there is high-temperature feldspar present in all the samples. This implies a postshock temperature above 600 C, and a small (less than 10 m) size of the ejecta. Current theories are well able to explain how objects of this size could have been ejected from Mars.

Hasan, F. A.↗

Transportation monitoring unit qualification

Transportation monitoring unit (TMU) qualification testing was performed between 3 Mar. and 14 Dec. 1989. The purpose of the testing was to qualify the TMUs to monitor and store temperature and acceleration data on redesigned solid rocket motor segments and exit cones while they are being shipped from Utah's Thiokol Corporation, Space Operations, to Kennedy Space Center. TMUs were subjected to transportation tests that concerned the structural integrity of the TMUs only, and did not involve TMU measuring capability. This testing was terminated prior to completion due to mounting plate failures, high and low temperature shutdown failures, and data collection errors. Corrective actions taken by the vendor to eliminate high temperature shutdowns were ineffective. An evaluation was performed on the TMUs to determine the TMU vibration and temperature measuring accuracy at a variety of temperatures. This test demonstrated that TMU measured shock levels are high, and that TMUs are temperature sensitive because of decreased accuracy at high and low temperatures. It was determined that modifications to the current TMU system, such that it could be qualified for use, would require a complete redesign and remanufacture. Because the cost of redesigning and remanufacturing the present TMU system exceeds the cost of procuring a new system that could be qualified without modification, it is recommended that an alternate transportation monitoring system be qualified.

Cook, M.↗

Charge transfer and X-ray emission from supernova remnants

The X-ray line emission excited by charge transfer between neutral hydrogen and the hydrogenic or fully stripped ions of heavy elements has been computed for a grid of nonequilibrium ionization models for supernova remnants. The effects of charge transfer excitation on the X-ray spectra of supernova remnants are discussed. The charge transfer process depends very sensitively upon the abundance of neutral hydrogen behind the shock. Consequently, a careful treatment of the ionization of hydrogen was required. The model line fluxes are compared with those excited by conventional collisional processes involving electrons. Results are presented in the form of contour plots for both the flux excited by charge transfer and the ratio of the charge transfer flux to that associated solely with collisional processes involving electrons. Charge transfer never contributes more than 10 percent of the flux of the strongest electron collisionally excited lines, and its contribution is typically 0.001 to 10 to the -5th for a shock moving into a medium composed of neutral hydrogen.

Wise, Michael W.↗

Hot film wall shear instrumentation for compressible boundary layer transition research

Experimental and analytical studies of hot film wall shear instrumentation were performed. A new hot film anemometer was developed and tested. The anemometer performance was not quite as good as that of commercial anemometers, but the cost was much less and testing flexibility was improved. The main focus of the project was a parametric study of the effect of sensor size and substrate material on the performance of hot film surface sensors. Both electronic and shock-induced flow experiments were performed to determine the sensitivity and frequency response of the sensors. The results are presented in Michael Moen's M.S. thesis, which is appended. A condensed form of the results was also submitted for publication.

Schneider, Steven P.↗

Examination of Mars2020 Shock-Layer Conditions via Infrared Laser Absorption Spectroscopy of CO2 and CO

Amid-infrared laser absorption diagnostic was deployed to study a simulated Mars2020 shock layer in the Electric Arc Shock Tube (EAST) facility at NASA’s Ames Research Center. Rapid RF-diplexing techniques enabled quantitative temperature and number density measurements of CO2 and CO with μs-resolution over an incident shock velocity range of 1.39 – 3.75 km/s. Two interband cascade lasers were utilized at 4.17 and 4.19 μm to resolve eight CO2 asymmetric stretch fundamental band (𝜈3) transitions from two different vibrational levels: 0000 (ground state) and 0110 (first excited bending mode). The probed rotational levels span across J” = 58 to J” = 140. Results are compared to DPLR simulations of the shock layer using kinetic mechanisms of Johnston et al. and Cruden et al. At shock velocities below 3.1 km/s, the agreement between the measurements and the Johnston mechanism is typically within 5% for temperature and within 10% for number density. At shock velocities above 3.1 km/s, the CO2 measurement becomes sensitive to a thin boundary layer and corrections of this effect are presented. On test cases with enough energy to dissociate CO2, a quantum cascade laser scanned the P(2, 20), P(0, 31), and P(3, 14) transitions of the CO fundamental band at 4.98 μm. CO formation rate is measured to be close to the Johnston kinetic mechanism at low velocities, and then trending towards the Cruden kinetic mechanism at high velocities. On a few low velocity test cases, rovibrational relaxation of the Martian atmosphere is probed with μs resolution.

Laser Absorption↗

Effect of Sandpaper and Grain Size on Non‐Shock Initiated Reactions in HMX

Abstract Three grades of HMX samples, coarse (A), coarse with a small amount of fines (B), and ultra‐fine (F), were tested for impact sensitivity by ERL drop hammer. The Type 12A test used sandpapers of three different compositions, 120‐, 180‐grit Si/C and 180‐grit garnet. Reaction was accounted for by operator observation and microphone. The results showed different sensitivity for each of the HMX types. The F‐HMX was the smallest in average particle size and was the least sensitive to impact. The A‐HMX was the next most stable and the B‐HMX was the most sensitive to impact. The spent samples from the drop hammer testing of B‐HMX and F‐HMX were further evaluated with optical imaging. Conditions were selected that were near the DH 50 values of the specific HMX. Previous literature has cited localized hot spot formation to be the probable cause of non‐shock initiated reactions leading to impact sensitivity. This study yielded a plethora of samples exhibiting hot spots for HMX materials, both without and with proximity to grit particles. Hot spots in the proximity of grit particles gave the most dramatic hot spots, but both types of hot spots were exhibited in samples considered reacted and non‐reacted. The F‐HMX, even though the most stable to impact sensitivity, exhibited the most and best resolved hot spots of all the samples and conditions. Foreign objects were also observed in some of the samples. Previous work has shown metal particles coming from wear of the anvils used in the drop hammer experiment can also form hot spots. However, none of the samples here with metal particles exhibited, in proximity, hot spot formation.

Reynolds, John G.↗

A REVERSE SHOCK IN GRB 130427A

We present extensive radio and millimeter observations of the unusually bright GRB 130427A at z = 0.340, spanning 0.67-12 days after the burst. We combine these data with detailed multi-band UV, optical, NIR, and Swift X-ray observations and find that the broadband afterglow emission is composed of distinct reverse shock and forward shock contributions. The reverse shock emission dominates in the radio/millimeter and at ∼< 0.1 days in the UV/optical/NIR, while the forward shock emission dominates in the X-rays and at ∼> 0.1 days in the UV/optical/NIR. We further find that the optical and X-ray data require a wind circumburst environment, pointing to a massive star progenitor. Using the combined forward and reverse shock emission, we find that the parameters of the burst include an isotropic kinetic energy of E{sub K,{sub iso}} ≈ 2 × 10{sup 53} erg, a mass loss rate of M-dot ∼3×10{sup -8} M{sub ☉} yr{sup –1} (for a wind velocity of 1000 km s{sup –1}), and a Lorentz factor at the deceleration time of Γ(200 s) ≈ 130. Due to the low density and large isotropic energy, the absence of a jet break to ≈15 days places only a weak constraint on the opening angle, θ{sub j} ∼> 2.°5, and therefore a total energy of E{sub γ} + E{sub K} ∼> 1.2 × 10{sup 51} erg, similar to other gamma-ray bursts (GRBs). The reverse shock emission is detectable in this burst due to the low circumburst density, which leads to a slow cooling shock. We speculate that this property is required for the detectability of reverse shocks in radio and millimeter bands. Following on GRB 130427A as a benchmark event, observations of future GRBs with the exquisite sensitivity of the Very Large Array and ALMA, coupled with detailed modeling of the reverse and forward shock contributions, will test this hypothesis.

79 ASTRONOMY AND ASTROPHYSICS↗

Experimental Evaluation of Fatigue Crack Initiation from Corroded Hemispherical Notches in Aerospace Structural Materials

A test program was developed and executed to evaluate the influence of corroded hemispherical notches on the fatigue crack initiation and propagation in aluminum 7075-T7351, 4340 steel, and D6AC steel. Surface enhancements such as shot peening and laser shock peening were also incorporated as part of the test effort with the intent of improving fatigue performance. In addition to the testing, fracture mechanics and endurance limit based analysis methods were evaluated to characterize the results with the objective of challenging typical assumptions used in modeling fatigue cracks from corrosion pits. The results specifically demonstrate that the aluminum and steel alloys behave differently with respect to fatigue crack initiation from hemispherical corrosion pits. The aluminum test results were bounded by the fracture mechanics and endurance limit models while exhibiting a general insensitivity to the residual stress field generated by shot peening. The steel specimens were better characterized by the endurance limit fatigue properties and did exhibit sensitivities to residual stresses from the shot peening and laser shock peening

Garcia, Daniel B.↗

High pressure shock tube ignition delay time measurements during oxy-methane combustion with high levels of CO 2 dilution

For this study, ignition delay times and methane species time-histories were measured for methane/O 2 mixtures in a high CO 2 diluted environment using shock tube and laser absorption spectroscopy. The experiments were performed between 1300 K and 2000 K at pressures between 6 and 31 atm. The test mixtures were at an equivalence ratio of 1 with CH 4 mole fractions ranging from 3.5% -5% and up to 85% CO 2 with a bath of argon gas as necessary. The ignition delay times and methane time histories were measured using pressure, emission, and laser diagnostics. Predictive ability of two literature kinetic mechanisms (GRI 3.0 and ARAMCO Mech 1.3) was tested against current data. In general, both mechanisms performed reasonably well against measured ignition delay time data. The methane time-histories showed good agreement with the mechanisms for most of the conditions measured. A correlation for ignition delay time was created taking into the different parameters showing that the ignition activation energy for the fuel to be 49.64 kcal/mol. Through a sensitivity analysis, CO 2 is shown to slow the overall reaction rate and increase the ignition delay time. To the best of our knowledge, we present the first shock tube data during ignition of methane/CO 2 /O 2 under these conditions. In conclusion, current data provides crucial validation data needed for development of future kinetic mechanisms.

42 ENGINEERING↗

TURBULENT MAGNETIC FIELD AMPLIFICATION FROM SPIRAL SASI MODES: IMPLICATIONS FOR CORE-COLLAPSE SUPERNOVAE AND PROTO-NEUTRON STAR MAGNETIZATION

We extend our investigation of magnetic field evolution in three-dimensional flows driven by the stationary accretion shock instability (SASI) with a suite of higher-resolution idealized models of the post-bounce core-collapse supernova environment. Our magnetohydrodynamic simulations vary in initial magnetic field strength, rotation rate, and grid resolution. Vigorous SASI-driven turbulence inside the shock amplifies magnetic fields exponentially; but while the amplified fields reduce the kinetic energy of small-scale flows, they do not seem to affect the global shock dynamics. The growth rate and final magnitude of the magnetic energy are very sensitive to grid resolution, and both are underestimated by the simulations. Nevertheless, our simulations suggest that neutron star magnetic fields exceeding 10{sup 14} G can result from dynamics driven by the SASI, even for non-rotating progenitors.

79 ASTRONOMY AND ASTROPHYSICS↗

Novel fabrication tools for dynamic compression targets with engineered voids using photolithography methods

Mesoscale imperfections, such as pores and voids, can strongly modify the properties and the mechanical response of materials under extreme conditions. Tracking the material response and microstructure evolution during void collapse is crucial for understanding its performance. In particular, imperfections in the ablator materials, such as voids, can limit the efficiency of the fusion reaction and ultimately hinder ignition. To characterize how voids influence the response of materials during dynamic loading and seed hydrodynamic instabilities, we, in this paper, have developed a tailored fabrication procedure for designer targets with voids at specific locations. Our procedure uses SU-8 as a proxy for the ablator materials and hollow silica microspheres as a proxy for voids and pores. By using photolithography to design the targets’ geometry, we demonstrate precise and highly reproducible placement of a single void within the sample, which is key for a detailed understanding of its behavior under shock compression. This fabrication technique will benefit high-repetition rate experiments at x-ray and laser facilities. Insight from shock compression experiments will provide benchmarks for the next generation of microphysics modeling.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Compositional effects on the ignition of FACE gasolines [Compositional effects on the ignition of FACE gasoline fuels: experiments, surrogate fuel formulation, and chemical kinetic modeling]

As regulatory measures for improved fuel economy and decreased emissions are pushing gasoline engine combustion technologies towards extreme conditions (i.e., boosted and intercooled intake with exhaust gas recirculation), fuel ignition characteristics become increasingly important for enabling stable operation. Here, this study explores the effects of chemical composition on the fundamental ignition behavior of gasoline fuels. Two well-characterized, high-octane, non-oxygenated FACE (Fuels for Advanced Combustion Engines) gasolines, FACE F and FACE G, having similar antiknock indices but different octane sensitivities and chemical compositions are studied. Ignition experiments were conducted in shock tubes and a rapid compression machine (RCM) at nominal pressures of 20 and 40 atm, equivalence ratios of 0.5 and 1.0, and temperatures ranging from 650 to 1270 K. Results at temperatures above 900 K indicate that ignition delay time is similar for these fuels. However, RCM measurements below 900 K demonstrate a stronger negative temperature coefficient behavior for FACE F gasoline having lower octane sensitivity. In addition, RCM pressure profiles under two-stage ignition conditions illustrate that the magnitude of low-temperature heat release (LTHR) increases with decreasing fuel octane sensitivity. However, intermediate-temperature heat release is shown to increase as fuel octane sensitivity increases. Various surrogate fuel mixtures were formulated to conduct chemical kinetic modeling, and complex multicomponent surrogate mixtures were shown to reproduce experimentally observed trends better than simpler two- and three-component mixtures composed of n-heptane, iso-octane, and toluene. Measurements in a Cooperative Fuels Research (CFR) engine demonstrated that the multicomponent surrogates accurately captured the antiknock quality of the FACE gasolines. Simulations were performed using multicomponent surrogates for FACE F and G to reveal the underlying chemical kinetics linking fuel composition with ignition characteristics. Finally, a key discovery of this work is the kinetic coupling between aromatics and naphthenes, which affects the radical pool population and thereby controls ignition.

02 PETROLEUM↗