SEARCH · Engineering Papers

Results for “functional and responsive materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 307 records · Page 17

All sources NASA NTRS DOE OSTI

NASA NTRS1980

Influence of stress interaction on the behavior of off-axis unidirectional composites

The yield function for plane stress of a transversely isotropic composite lamina consisting of stiff, linearly elastic fibers and a von Mises matrix material is formulated in terms of Hill's elastic stress concentration factors and a single plastic constraint parameter. The above are subsequently evaluated on the basis of observed average lamina and constituent response for the Avco 5505 boron epoxy system. It is shown that inclusion of residual stresses in the yield function together with the incorporation of Dubey and Hillier's concept of generalized yield stress for anisotropic media in the constitutive equation correctly predicts the trends observed in experiments. The incorporation of the strong axial stress interaction necessary to predict the correct trends in the shear response is directly traced to the high residual axial stresses in the matrix induced during fabrication of the composite.

Pindera, M. J.↗

DOE OSTI2022

Dynamic Response of an Electron Gas: Towards the Exact Exchange-Correlation Kernel

Precise calculations of dynamics in the homogeneous electron gas (jellium model) are of fundamental importance for design and characterization of new materials. In this work, we introduce a diagrammatic Monte Carlo technique based on algorithmic Matsubara integration that allows us to compute frequency and momentum resolved finite temperature response directly in the real frequency domain using series of connected Feynman diagrams. The data for charge response at moderate electron density are used to extract the frequency dependence of the exchange-correlation kernel at finite momenta and temperature. These results are as important for development of the time-dependent density functional theory for materials dynamics as ground state energies are for the density functional theory.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

NASA NTRS1983

Constitutive Models Based on Compressible Plastic Flows

The need for describing materials under time or cycle dependent loading conditions has been emphasized in recent years by several investigators. In response to the need, various constitutive models describing the nonlinear behavior of materials under creep, fatigue, or other complex loading conditions were developed. The developed models for describing the fully dense (non-porous) materials were mostly based on uncoupled plasticity theory. The improved characterization of materials provides a better understanding of the structual response under complex loading conditions. The pesent studies demonstrate that the rate or time dependency of the response of a porous aggregate can be incorporated into the nonlinear constitutive behavior of a porous solid by appropriately modeling the incompressible matrix behavior. It is also sown that the yield function which wads determined by a continuum mechanics approach must be verified by appropriate experiments on void containing sintered materials in order to obtain meaningful numbers for the constants that appear in the yield function.

Rajendran, A. M.↗

NASA NTRS1995

Sensitivity analysis of the non-linear dynamic viscoplastic response of 2-d structures with respect to material parameters

A computational procedure is presented for evaluating the sensitivity coefficients of the viscoplastic response of structures subjected to dynamic loading. A state of plane stress is assumed to exist in the structure, a velocity strain-Cauchy stress formulation is used, and the geometric non-linearities arising from large strains are incorporated. The Jaumann rate is used as a frame indifferent stress rate. The material model is chosen to be isothermal viscoplasticity, and an associated flow rule is used with a von Mises effective stress. The equations of motion emanating from a finite element semi-discretization are integrated using an explicit central difference scheme with an implicit stress update. The sensitivity coefficients are evaluated using a direct differentiation approach. Since the domain of integration is the current configuration, the sensitivity coefficients of the spatial derivatives of the shape functions must be included. Numerical results are presented for a thin plate with a central cutout subjected to an in-plane compressive loading. The sensitivity coefficients are generated by evaluating the derivatives of the response quantities with respect to Young's modulus, and two of the material parameters characterizing the viscoplastic response. Time histories of the response and sensitivity coefficients, and spatial distributions at selected times are presented.

Kulkarni, Makarand↗

NASA NTRS2005

Subscale Test Methods for Combustion Devices

Stated goals for long-life LRE s have been between 100 and 500 cycles: 1) Inherent technical difficulty of accurately defining the transient and steady state thermochemical environments and structural response (strain); 2) Limited statistical basis on failure mechanisms and effects of design and operational variability; and 3) Very high test costs and budget-driven need to protect test hardware (aversion to test-to-failure). Ambitious goals will require development of new databases: a) Advanced materials, e.g., tailored composites with virtually unlimited property variations; b) Innovative functional designs to exploit full capabilities of advanced materials; and c) Different cycles/operations. Subscale testing is one way to address technical and budget challenges: 1) Prototype subscale combustors exposed to controlled simulated conditions; 2) Complementary to conventional laboratory specimen database development; 3) Instrumented with sensors to measure thermostructural response; and 4) Coupled with analysis

Anderson, W. E.↗

DOE OSTI2022

Thermal scattering law for structure-dependent-Doppler broadening in FLASSH

Traditional Doppler broadening methods assume that target nuclei velocities follow a Maxwell-Boltzmann distribution which inherently assumes that the atoms are a free gas or that their velocities are independent of each other. This approximation is reasonable at high target temperatures and high neutron energies. However, nuclei are not independent: the lattice temperature and chemical binding will define the atomic motion. The thermal scattering law (i.e., TSL or S(α,β)) is a material property which describes the chemical binding and temperature response in terms of available momentum and energy states. In the thermal energy range, this TSL will define the thermal scattering cross sections. In the resonance region, the TSL offers a first-principles description of the probability distribution function for the velocity of the target nuclei. Using the TSL in Doppler broadening captures the structure of the material consistently from the thermal range into the resonance cross sections. In this work, both traditional free-gas and precise TSL Doppler broadening methods for resonance cross section evaluation have been implemented within the Full Law Analysis Scattering System Hub (FLASSH). This framework provides a generalized formulation for evaluating low-lying resonance data and streamlines nuclear data processing methods. TSL data generated using ab initio lattice dynamics (AILD) can be used to broaden cross section libraries in ENDF format for high-fidelity input into reactor physics calculations. These capabilities are demonstrated for the lowest absorption resonances of {sup 238}U in UO{sub 2}, UC and UN. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2025

Odd-Parity Magnetism Driven by Antiferromagnetic Exchange

Realizing odd-parity, time-reversal-preserving, nonrelativistic spin splitting is a central goal for spintronics applications. We propose a group-theory-based microscopic framework to induce odd-parity spin splitting from coplanar antiferromagnetic (AFM) states without spin-orbit coupling (SOC). We develop phenomenological models for 421 conventional period-doubling AFM systems in nonsymmorphic space groups and construct minimal microscopic models for 119 of these. We find that these AFM states can attain three possible competing ground states. These ground states all break symmetries in addition to those broken by the usual AFM order. Specifically, they give rise to either odd-parity spin-splitting, nematic order, or scalar odd-parity order related to multiferroicity. Our microscopic theories reveal that the odd-parity spin-splitting energy scale is generically large and further reveal that the scalar odd-parity order gives a nonzero Berry curvature dipole without SOC. We identify 67 materials in the Magndata database for which our theory applies. We provide density-functional theory (DFT) calculations on Fe-based materials that reveal an ℎ-wave spin splitting consistent with our symmetry arguments and apply our microscopic model to determine the nonrelativistic Edelstein response for CeNiAsO.

Antiferromagnets↗

DOE OSTI2021

Dopamine-Mediated Polymer Coating Facilitates Area-Selective Atomic Layer Deposition

Area-selective atomic layer deposition (ALD) has the potential to significantly improve current fabrication approaches by introducing a bottom-up process in which robust and conformal thin films are selectively deposited onto patterned substrates. This bottom-up approach requires selective areas of the substrates to be masked to inhibit deposition. Spontaneous self-assembly and organization of a mask, incorporating adhesion and other functions, are particularly attractive for this role as they do not require a separate patterning step. In this work, we make use of the pH/light tunability of catechol adhesion to develop a catechol-functionalized polymer that exhibits tunable adhesion strengths on different materials based on their specific chemistry. Tunable selective deposition was shown between metal/metal oxide substrates by controlling the local pH. Moreover, by controlling the adhesion strength through UV light, the deposition of hafnium oxide (HfO 2 ) during ALD was successfully inhibited.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Measurements of nematic susceptibility with phase sensitive nuclear magnetic resonance in pulsed strain fields

Here, we present nuclear magnetic resonance data in BaFe 2 As 2 in the presence of pulsed strain fields that are interleaved in time with the radio frequency excitation pulses. In this approach, the preceding nuclear magnetization acquires a phase shift that is proportional to the strain and pulse time. The sensitivity of this approach is limited by the homogeneous decoherence time, T 2 , rather than the inhomogeneous linewidth. We measure the nematic susceptibility as a function of temperature and demonstrate a three orders of magnitude improvement in sensitivity. This approach will enable studies of the strain response in a broad range of materials that previously were inaccessible due to inhomogeneous broadening.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Grain2Mesh: Mesh Generation for Grain-Scale Nonlinear Elasticity Modeling

The nonlinear hysteretic behavior of rocks under cyclic loading is a crucial area of study in geomechanics. The macroscopic response of a variety of materials has been found to be contingent upon the behavior of the micro-scale structure. This project aims to develop a functional and maintainable software package for generating a multi-phase numerical mesh and accompanying simulation files for finite element modeling used in computational mechanics solvers. Meshes generated from images often lack key preprocessing that reduces noise and prevents mesh element distortion that can increase computational cost. By incorporating user feedback throughout, grain2mesh ensures a high-fidelity mesh that can be used to model grain-scale interactions such as shearing, crack propagation, and interfacial material contrast. Scientific applications of this software include material fracturing, stress-strain analysis for natural and engineered materials, and nonlinear meso-scale analysis.

54 ENVIRONMENTAL SCIENCES↗

NASA NTRS1984

The role of water in slip casting

Slips and casting are considered in terms of physical and colloidal chemistry. Casting slips are polydisperse suspensions of lyophobic particles in water, whose degree of coagulation is controlled by interaction of flocculating and deflocculating agents. Slip casting rate and viscosity are functions of temperature. Slip rheology and response to deflocculating agents varies significantly as the kinds and amounts of colloid modifiers change. Water is considered as a raw material. Various concepts of water/clay interactions and structures are discussed. Casting is a de-watering operation in which water moves from slip to cast to mold in response to a potential energy termed moisture stress. Drying is an evaporative process from a free water surface.

Mccauley, R. A.↗

NASA NTRS2009

Cratering Equations for Zinc Orthotitanate Coated Aluminum

The final STS-125 servicing mission (SM4) to the Hubble Space Telescope (HST) in May of 2009 saw the return of the 2nd Wide Field Planetary Camera (WFPC2) aboard the shuttle Discovery. This hardware had been in service on HST since it was installed during the SM1 mission in December of 1993 yielding one of the longest low Earth orbit exposure times (15.4 years) of any returned space hardware. The WFPC2 is equipped with a 0.8 x 2.2 m radiator for thermal control of the camera electronics (Figure 1). The space facing surface of the 4.1 mm thick aluminum radiator is coated with Z93 zinc orthotitanate thermal control paint with a nominal thickness of 0.1 0.2 mm. Post flight inspections of the radiator panel revealed hundreds of micrometeoroid/orbital debris (MMOD) impact craters ranging in size from less than 300 to nearly 1000 microns in diameter. The Z93 paint exhibited large spall areas around the larger impact sites (Figure 2) and the craters observed in the 6061-T651 aluminum had a different shape than those observed in uncoated aluminum. Typical hypervelocity impact craters in aluminum have raised lips around the impact site. The craters in the HST radiator panel had suppressed crater lips, and in some cases multiple craters were present instead of a single individual crater. Humes and Kinard observed similar behavior after the WFPC1 post flight inspection and assumed the Z93 coating was acting like a bumper in a Whipple shield. Similar paint behavior (spall) was also observed by Bland2 during post flight inspection of the International Space Station (ISS) S-Band Antenna Structural Assembly (SASA) in 2008. The SASA, with similar Z93 coated aluminum, was inspected after nearly 4 years of exposure on the ISS. The multi-crater phenomena could be a function of the density, composition, or impact obliquity angle of the impacting particle. For instance, a micrometeoroid particle consisting of loosely bound grains of material could be responsible for creating the multiple craters. Samples were obtained from the HST largest craters for examination by electron microscope equipped with x-ray spectrometers to determine impactor source (micrometeoroid or orbital debris). In an attempt to estimate the MMOD particle diameters that produced these craters, this paper will present equations for spall diameter, crater depth and crater diameter in Z93 coated aluminum. The equations will be based on hypervelocity impact tests of Z93 painted aluminum at the NASA White Sands Test Facility. Equations inputs for velocities beyond the testable regime are expected from hydrocode simulations of Z93 coated aluminum using CTH and ANSYS AUTODYN.

Hyde, James↗

NASA NTRS2023

P-ACTIVE Project Report

The Phase change material-based actively-tunable filter (P-ACTIVE, Dr. Hyun Jung Kim, the Principal Investigator / PI) project is a NASA Langley Research Center (LaRC)-led research endeavor that began as a NASA CIF (Center Innovation Fund) project in 2019. The goal of P-ACTIVE is to develop all-solid-state tunable optical filters that can serve as low-Size, Weight, and Power (SWaP) replacements to the ubiquitous filter wheel technology current in use, and serve as a starting point for completely new optical component technologies. By using materials commonly used in electronic memory devices, namely chalcogenide phase-change materials (PCMs), in conjunction with nanostructured surfaces with exotic, tailored optical responses (“metasurfaces”), the P-ACTIVE filters are able to tune their optical transmission/reflection behavior in real-time. Because of this new functionality, P-ACTIVE filters are highlighted for NASA science and space programs such as next generation Lidar, landing system (SLS) thermal monitoring, thermal imaging, imaging spectroscopy, and disaster monitoring (e.g., volcanic eruption observations from SmallSats). This document intends to serve as a compendium of the P-ACTIVE project. We begin by describing the project from background science and assume no prior knowledge of the subject. We then address experimental and theoretical results of P-ACTIVE device performance, as well as recent results obtained from the MISSE-14 mission related to space qualification of P-ACTIVE devices and constituent materials. We conclude with a prospective view of the P-ACTIVE technology, and discuss the potential for these filters and other similar metasurface devices to serve NASA’s mission.

metamaterial↗

DOE OSTI2021

Control of polarization in bulk ferroelectrics by mechanical dislocation imprint

Defects are essential to engineering the properties of functional materials ranging from semiconductors and superconductors to ferroics. Whereas point defects have been widely exploited, dislocations are commonly viewed as problematic for functional materials and not as a microstructural tool. In this work, we developed a method for mechanically imprinting dislocation networks that favorably skew the domain structure in bulk ferroelectrics and thereby tame the large switching polarization and make it available for functional harvesting. The resulting microstructure yields a strong mechanical restoring force to revert electric field–induced domain wall displacement on the macroscopic level and high pinning force on the local level. This induces a giant increase of the dielectric and electromechanical response at intermediate electric fields in barium titanate [electric field–dependent permittivity (ε 33 ) ≈ 5800 and large-signal piezoelectric coefficient ( d 33 *) ≈ 1890 picometers/volt]. Dislocation-based anisotropy delivers a different suite of tools with which to tailor functional materials.

36 MATERIALS SCIENCE↗

DOE OSTI2021

The 3D printing and modeling of functionally graded Kelvin foams for controlling crushing performance

Mechanical impact protection is an important consideration in many applications, ranging from product transportation to sports. Cellular materials are typically used due to their desirable energy absorption properties and light weight. However, their large deformation and rate dependent responses (especially of polymer foams) are challenging to consider in design. Additionally, the use of foams with uniform properties, such as uniform density and uniform stiffness, often restricts the designed foams to only be suitable for a narrow range of mechanical impact conditions whereas real applications commonly face unpredictable situations. 3D printing offers fabrication flexibility and thus opens the door to create foams with tailored properties. In this work, we investigate the feasibility of using 3D printing for functionally graded foams (FGFs) that are optimal over a broad range of mechanical environments. The foams are fabricated by the recently developed grayscale digital light processing (g-DLP) method which can print parts with locally designed properties. These foams are tested under drop test conditions and with slower displacement control. We also model the large deformation behavior of FGFs using finite element analysis in which we account for the different viscoelastic behaviors of the distinct grayscale regions. We then use the model to examine the impact mitigation capabilities of FGFs in different loading scenarios. Finally, we show how FGFs can be used to satisfy real-world design goals using the case study of a motorcycle helmet. In contrast to prior work, we investigate continuous, functionally graded foams of a single density that differ in their viscoelastic responses. This work provides further insight into the benefits of viscoelastic properties and modulus graded foams and presents a manufacturing approach that can be used to produce the next generation of flexible lattice foams as mechanical absorbers.

3D printing↗

DOE OSTI2025

Propulsion of synthetic protocells and coacervates driven by biochemical catalysis

An important area in the design of biomolecular materials is the mimicry of cellular function through the assembly of molecular components into synthetic cells, or protocells. Through compartmentalization and subsequent evolution, biological cells have achieved the goals of specificity, amplification, and response. By assembling cell-like structures that mimic the organization and size of a natural cell but that incorporate novel components and respond to synthetic triggers, we can extend their capabilities beyond what is currently achievable in biology. For applications in energy, these include the ability to convert chemical to mechanical energy, and to enable the response of sensors and responders once a threshold has been reached. This technical report summarizes progress made on this project as of Dec 31, 2023.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Applying Dynamic Strain on Thin Oxide Films Immobilized on a Pseudoelastic Nickel-Titanium Alloy

Direct alteration of materials structure/function through strain is a burgeoning area of research that has allowed for novel properties of materials to emerge. Tuning materials structure can be achieved by controlling an external force imposed on materials and inducing stress-strain responses (i.e., applying dynamic strain). Electroactive thin films are typically deposited on shape or volume tunable elastic substrates, where mechanical loading (i.e. compression or tension) can affect films structure and function through imposed strain. Here we summarize methods for straining n-type doped titanium dioxide (TiO2) films prepared by a thermal treatment of a pseudo-elastic nickel-titanium alloy. The main purpose of the described methods is to study how strain affects electrocatalytic activities of metal oxide, specifically hydrogen evolution and oxygen evolution reactions. The same system can be adapted to study the effect of strain more broadly. Strain engineering can be applied for optimization of a material function, as well as for design of adjustable, multifunctional (photo)electrocatalytic materials under external stress control.

92 SC - Basic Energy Sciences (BES) (SC-22)↗

NASA NTRS1997

Absolute Calibration of the AXAF Telescope Effective Area

The prelaunch calibration of AXAF encompasses many aspects of the telescope. In principle, all that is needed is the complete point response function. This is, however, a function of energy, off-axis angle of the source, and operating mode of the facility. No single measurement would yield the entire result. Also, any calibration made prior to launch will be affected by changes in conditions after launch, such as the change from one g to zero g. The reflectivity of the mirror and perhaps even the detectors can change as well, for example by addition or removal of small amounts of material deposited on their surfaces. In this paper, we give a broad view of the issues in performing such a calibration, and discuss how they are being addressed in prelaunch preparation of AXAF. As our title indicates, we concentrate here on the total throughput of the observatory. This can be thought of as the integral of the point response function, i.e. the encircled energy, out ot the largest practical solid angle for an observation. Since there is no standard x-ray source in the sky whose flux is known to the -1% accuracy we are trying to achieve, we must do this calibration on the ground. we also must provide a means for monitoring any possible changes in this calibration from pre-launch until on-orbit operation can transfer the calibration to a celestial x-ray source whose emission is stable. In this paper, we analyze the elements of the absolute throughput calibration, which we call Effective Area. We review the requirements for calibrations of components or subsystems of the AXAF facility, including mirror, detectors, and gratings. We show how it is necessary to calibrate this ground-based detection system at standard man-made x-ray sources, such as electron storage rings. We present the status of all these calibrations, with indications of the measurements remaining to be done, even though the measurements on the AXAF flight optics and detectors will have been completed by the time this paper is presented. We evaluate progress toward the goal of making 1% measurements of the absolute x-ray flux from astrophysical sources, so that comparisons can be made with their emission at other wavelengths, in support of observations such as the Sunyaev-Zeldovitch effect, which can give absolute distance measurements independent of the traditional distance measuring techniques in astronomy.

Kellogg, E.↗