Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Understanding of Ag Nanocatalysts for Electrocatalytic CO2 Conversion: Effects of Particle Size and Carbon Support

In this talk, we combined ultrahigh vacuum (UHV) surface science techniques, electrochemical measurements, and computational modeling to investigate Ag based electrocatalysts for CO2 reduction reaction (CO2RR). Our goal is to understand the critical characteristics governing the activity and selectivity of Ag electrocatalysts. Ag electrocatalysts were grown on highly oriented pyrolytic graphite (HOPG) in the UHV chamber, characterized with X-ray photoelectron spectroscopy (XPS) and scanning tunneling microscopy (STM), and then tested in a custom-built gastight H-cell. Supported by computational modeling based on density functional theory (DFT) calculations and microkinetic modeling (MKM), our studies revealed a strong size-dependent electrocatalytic CO2-to-CO conversion of the Ag nanoparticle electrocatalysts with average particle diameter between 2 to 6 nm. Smaller diameter (< 3 nm) particles favored H2 evolution reaction (HER) due to a high population of Ag edge sites, whereas larger diameter particles favored CO2RR as the population of Ag(100) surface sites grew. We further discovered that electronic interactions between small diameter Ag particles and highly defective carbon supports could break the size-dependent CO2RR reactivity, resulting in highly selective (CO Faradaic Efficiency > 90%) and active Ag nanoparticle electrocatalysts with sizes < 2 nm diameter. This knowledge is key to understand electrocatalysts performance and to ultimately guide electrocatalyst design

Ag nanoparticles↗
DOE OSTI2025

Optimization of Ag Electrocatalyst Performance for CO2 to CO Conversion: Pairing Atomic Simulations with Experiments

Density-functional theory- based calculations that complement our series of experimental efforts on optimizing Ag electrocatalyst performance for CO2 to CO conversion were presented. Three key findings are drawn out from the combined UHV surface science, STM and electrochemical measurements: (1) Using a series of Ag nanoparticles with 2-6 nm average diameters, CO2 reduction reaction (CO2RR) activity increases, with particle between 2 nm and ∼4 nm demonstrating the highest combination of activity and selectivity; (2) Electronic metal−support interactions (EMSIs) between Ag and C dramatically improve CO2RR performance as evidenced by a scaling relationship between particle size and the relative Ag−C EMSIs strength, which improves the CO2-to-CO Faradaic efficiency of sub-2 nm Ag particles from 2 to ∼100% and increases the CO turnover frequency ∼15-fold compared with similarly sized bare Ag particles; (3) The performance Ag electrocatalysts is improved when supported on S-doped C materials. Computational modeling of 1−10 nm Ag particles predicts a nearly identical size-dependent trend with maximum CO2RR activity predicted for 3.7nm particles. The calculations support the promotional effect of C materials, showing a large charge transfer of 1.02 e from Ag clusters to defective C and a 0.41 eV less endergonic step of forming COOH intermediate on Ag/defective-C compared to the Ag/C system. Calculations indicate a more favorable energetic pathway of CO2-to-CO at the C-S-Ag interface, consistent with experiments.

CO2 utilization↗
DOE OSTI2026

Microscopic Scattering Approach to In-Gap States

We develop a microscopic scattering formalism to describe Yu-Shiba-Rusinov (YSR) states due to a single Cr adatom on the Bi-terminated surface of beta Bi2Pd, by combining ab initio Wannier functions with a real-space Green's function approach in the Bogoliubov-de Gennes formalism[1]. Our framework reproduces key scanning tunneling spectroscopy features, including a single particle-hole asymmetric YSR peak and isotropic dIdV maps around the impurity. Decomposing the YSR states reveals contributions from four nearly degenerate C4v representations, with energy broadening masking their individual signatures. Spin-orbit coupling induces partial spin polarization, while the spatial asymmetry between particle and hole components arises from Cr d-Bi p hybridization. These results highlight the importance of realistic band structures and microscopic modeling for interpreting STM data for magnetic in-gap states on superconductors. Further advances examining layered 2D material surfaces, such as NbSe2, will be described[2]. For this system the superconducting properties are obtained from a full anisotropic Eliashberg calculation of the superconducting order parameter along with the charge density wave gap. Additional features associated with proposals to measure the dynamics of these individual YSR states will be presented. [1] arXiv:2507.08740 [2] arXiv:2507.11856

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Experimental Operation of a Prototype 750C Advanced Chloride Molten Salt Bellows Valve

To achieve DOE 2030 SunShot targets that reduce the cost of liquid-based solar by an additional 40% to 70% beyond 2018 costs, a more reliable, highly manufacturable flow valve, capable of achieving operational temperatures of >700°C is required [1]. This paper investigates the development of an innovative high-temperature chloride molten salt valve, with operation up to 750°C. This valve is intended to be employed within Gen 3 CSP liquid-based thermal energy storage (TES) systems as well as Gen 4 modular salt reactor (MSR) technologies. This work details the general design and flow testing of a bellows-seal flow control valve (FCV). This design includes an integrated closed-loop thermal control system to ensure robust design for freeze-thaw cycles. The self-contained thermal management STM system, is unique in the salt valve industry since it is an integrated solution to provide a consistent, repeatable alternative to typical heat tracing. Additionally, the design includes the employment of a novel heat pipe valve stem to facilitate enhanced passive thermal management into the valve assembly. This valve stem heat pipe is designed to facilitate natural circulation within the bonnet to ensure robust operation, during both nominal and transient thermal operation. The valve body and trim will be designed using SS316H, consistent with Flowserve Corporation’s existing product base and is code qualified but will utilize clad material for materials corrosion, manufacturing cost reduction and compatibility to ensure design flexibility. A test campaign was performed in this investigation utilizing a novel 750°C ternary chloride (20%NaCl/40%MgCl2/40%KCl by mol. wt. %) molten salt flow loop. A discussion about the design and installation of the valves within this test bed is provided for this investigation. Valve test results from this study assessed Cv curves as well as multiple actuator cycles, under varying thermodynamic and operational mode conditions, which would be characteristic within a commercial molten salt facility. The results indicate nominal operation for the baseline design, though improved performance and reliability is expected with the full designed FCV.

Armijo, Kenneth (ORCID:0000000346832147)↗
DOE OSTI2021

Atomic-Scale Visualization of the Cuprate Pair Density Wave State

A recent discovery of the pair density wave (PDW) order creates a stir in understanding an underlying physics in the pseudogap states of the cuprate high temperature superconductors. Recent Spectroscopic Imaging Scanning Tunneling Microscopy (SI-STM) measurements on Bi 2 Sr 2 CaCu 2 O 8+δ identified that spatially uniform d-wave superconductivity (DSC), d-symmetry charge density wave (CDW), and the PDW play important roles in an intertwined fashion. In this paper, we discuss how these different electronic degrees of freedom emerges in electronic structures of the cuprate and discuss how they are related to each other.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1975

Mission Analysis Program for Solar Electric Propulsion (MAPSEP). Volume 2: User's manual for earth orbital MAPSEP

The trajectory simulation mode (SIMSEP) requires the namelist SIMSEP to follow TRAJ. The SIMSEP contains parameters which describe the scope of the simulation, expected dynamic errors, and cumulative statistics from previous SIMSEP runs. Following SIMSEP are a set of GUID namelists, one for each guidance correction maneuver. The GUID describes the strategy, knowledge or estimation uncertainties and cumulative statistics for that particular maneuver. The trajectory display mode (REFSEP) requires only the namelist TRAJ followed by scheduling cards, similar to those used in GODSEP. The fixed field schedule cards define: types of data displayed, span of interest, and frequency of printout. For those users who can vary the amount of blank common storage in their runs, a guideline to estimate the total MAPSEP core requirements is given. Blank common length is related directly to the dimension of the dynamic state (NDIM) used in transition matrix (STM) computation, and, the total augmented (knowledge) state (NAUG). The values of program and blank common must be added to compute the total decimal core for a CDC 6500. Other operating systems must scale these requirements appropriately.

Source record↗
NASA NTRS1986

Stirling engine external heat system design with heat pipe heater

This final report presents the conceptual design of a liquid fueled external heating system (EHS) and the preliminary design of a heat pipe heater for the STM-4120 Stirling cycle engine, to meet the Air Force mobile electric power (MEP) requirement for units in the range of 20 to 60 kW. The EHS design had the following constraints: (1) Packaging requirements limited the overall system dimensions to about 330 mm x 250 mm x 100 mm; (2) Heat flux to the sodium heat pipe evaporator was limited to an average of 100 kW/m and a maximum of 550 kW/m based on previous experience; and (3) The heat pipe operating temperature was specified to be 800 C based on heat input requirements of the STM4-120. An analysis code was developed to optimize the EHS performance parameters and an analytical development of the sodium heat pipe heater was performed; both are presented and discussed. In addition, construction techniques were evaluated and scale model heat pipe testing performed.

Godett, Ted M.↗
NASA NTRS1989

Historical perspective - Viking Mars Lander propulsion

This paper discusses the Viking 1 and 2 missions to Mars in 1975-1976 and describes the design evolution of the Viking Terminal Descent Rocket Engines responsible for decelerating the Viking Mars Landers during the final portion of their descent from orbit. The Viking Terminal Descent Rocket Engines have twice the thrust of the largest monopropellant hydrazine engine developed previously but weigh considerably less. The engine has 18 nozzles, the capability of 10:1 throttling, is totally sealed until fired, employs no organic unsealed materials, is 100 percent germ free, utilized hydrazine STM-20 as the propellant, and starts at a temperature more than 45 F below the propellant's freezing point.

Morrisey, Donald C.↗
NASA NTRS1990

Ballistic-Electron-Emission Microscope

Ballistic-electron-emission microscope (BEEM) employs scanning tunneling-microscopy (STM) methods for nondestructive, direct electrical investigation of buried interfaces, such as interface between semiconductor and thin metal film. In BEEM, there are at least three electrodes: emitting tip, biasing electrode, and collecting electrode, receiving current crossing interface under investigation. Signal-processing device amplifies electrode signals and converts them into form usable by computer. Produces spatial images of surface by scanning tip; in addition, provides high-resolution images of buried interface under investigation. Spectroscopic information extracted by measuring collecting-electrode current as function of one of interelectrode voltages.

Kaiser, William J.↗
NASA NTRS1988

Spatially resolved ballistic electron spectroscopy of subsurface interfaces

Buried interfaces have traditionally been inaccessible to direct investigation by surface-sensitive techniques. A unique and novel electronic probe, which is sensitive to subsurface electronic structure, has been utilized to probe Schottky barrier interfaces. The method, ballistic electron emission microscopy (BEEM), is based on scanning tunnelling microscopy (STM) techniques. A theoretical treatment has been developed to describe the ballistic electron spectra obtained by BEEM and this treatment is applied to data obtained on the Au-Si Schottky barrier interface system. Excellent agreement between experiment and theory is obtained. In addition, the treatment predicts nanometer spatial resolution for interface imaging by BEEM.

Bell, L. D.↗
NASA NTRS1992

X-ray scattering measurements from thin foil X-ray mirrors

Thin foil X-ray mirrors are to be used as the reflecting elements in the telescopes of the X-ray satellites Spectrum-X-Gamma (SRG) and ASTRO-D. High resolution X-ray scattering measurements from the Au coated and dip-lacquered Al foils are presented. These were obtained from SRG mirrors positioned in a test quadrant of the telescope structure and from ASTRO-D foils held in a simple fixture. The X-ray data is compared with laser data and other surface structure data such as STM, atomic force microscopy (AFM), TEM, and electron micrography. The data obtained at Cu K-alpha(1), (8.05 keV) from all the mirrors produced on Al foils shows a scatter which limits the obtainable half-power width to above 1.5 arcmin. Mirrors based on electroformed Ni foils, however, show local regions with a factor of 4 better performance, and they are being developed for future applications.

Christensen, F. E.↗
NASA NTRS1994

The effect of Low Earth Orbit exposure on some experimental fluorine and silicon-containing polymers

Several experimental fluorine and silicon-containing polymers in film form were exposed to low Earth orbit (LEO) on a Space Shuttle flight experiment (STS-46, Evaluation of Oxygen Interaction with Materials, EOIM-3). The environmental parameters of primary concern were atomic oxygen (AO) and ultraviolet (UV) radiation. The materials were exposed to 2.3 plus or minus 0.1 x 10(exp 20) oxygen atoms/sq cm and 30.6 UV sun hours during the flight. In some cases, the samples were exposed at ambient, 120 C and 200 C. The effects of exposure on these materials were assessed utilizing a variety of characterization techniques including optical, scanning electron (SEM) and scanning tunneling (STM) microscopy, UV-visible (UV-VIS) transmission, diffuse reflectance infrared (DR-FTIR), x-ray photoelectron (XPS) spectroscopy, and in a few cases, gel permeation chromatography (GPC). In addition, weight losses of the films, presumably due to AO erosion, were measured. The fluorine-containing polymers exhibited significant AO erosion and exposed films were diffuse or 'frosted' in appearance and consequently displayed dramatic reductions in optical transmission. The silicon-containing films exhibited minimum AO erosion and the optical transmission of exposed films was essentially unchanged. The silicon near the exposed surface in the films was converted to silicate/silicon oxide upon AO exposure which subsequently provided protection for the underlying material. The silicon-containing epoxies are potentially useful as AO resistant coatings and matrix resins as they are readily processed into carbon fiber reinforced composites and cured via electron radiation.

Connell, John W.↗
NASA NTRS1995

Semiempirical Analysis of Surface Alloy Formation

The BFS method for alloys is applied to the study of surface alloy formation. This method was previously used to examine the experimental STM observation of surface alloying of Au on Ni(110) for low Au coverages by means of a numerical simulation. In this work, we extend the study to include other cases of surface alloying for immiscible as well as miscible metals. All binary combinations of Ni, Au, Cu, and Al are considered and the simulation results are compared to experiment when data is available. The driving mechanisms of surface alloy formation are then discussed in terms of the BFS method and the available results.

Bozzolo, Guillermo↗
NASA NTRS1996

Electronic-To-Optical-To-Electronic Packet-Data Conversion

Space-time multiplexer (STM) cell-based communication system designed to take advantage of both high throughput attainable in optical transmission links and flexibility and functionality of electronic processing, storage, and switching. Long packets segmented and transmitted optically by wavelength-division multiplexing. Performs optoelectronic and protocol conversion between electronic "store-and-forward" protocols and optical "hot-potato" protocols.

Monacos, Steve↗
NASA NTRS1996

Alkali layered compounds interfaces for energy conversion and energy storage

During year one a new ultra-high vacuum, an Ar(+) ion sputterer, a low energy electron diffraction (LEED) system, an Auger electron spectrometer (AES), a work function measurement device with a Kelvin probe, and related accessories were used. The study found a focus in the adsorption of chalcogenides on Si and III-V compound semiconductors. In the second year, a scanning tunneling microscope was obtained along with a quadrapole mass spectrometer, power supplies, a computer, a chart recorder, etc. We started the systematic study on the adsorption of chalcogenides on the compound semiconductor surfaces. The third year saw the mounting of the scanning tunneling microscope (STM) on the existing UHV system. The investigation continued with the adsorption of Cs (alkali) on S-covered Si(100)2x1 surfaces. Then the adsorption of S on Cs-covered Si(100) surfaces was studied.

Papageorgopoulos, Chris A.↗
NASA NTRS2000

Reliable, Low-Cost, Low-Weight, Non-Hermetic Coating for MCM Applications

Through an Air Force Research Laboratory sponsored STM program, reliable, low-cost, low-weight, non-hermetic coatings for multi-chip-module(MCK applications were developed. Using the combination of Sandia Laboratory ATC-01 test chips, AvanTeco's moisture sensor chips(MSC's), and silicon slices, we have shown that organic and organic/inorganic overcoatings are reliable and practical non-hermetic moisture and oxidation barriers. The use of the MSC and unpassivated ATC-01 test chips provided rapid test results and comparison of moisture barrier quality of the overcoatings. The organic coatings studied were Parylene and Cyclotene. The inorganic coatings were Al2O3 and SiO2. The choice of coating(s) is dependent on the environment that the device(s) will be exposed to. We have defined four(4) classes of environments: Class I(moderate temperature/moderate humidity). Class H(high temperature/moderate humidity). Class III(moderate temperature/high humidity). Class IV(high temperature/high humidity). By subjecting the components to adhesion, FTIR, temperature-humidity(TH), pressure cooker(PCT), and electrical tests, we have determined that it is possible to reduce failures 50-70% for organic/inorganic coated components compared to organic coated components. All materials and equipment used are readily available commercially or are standard in most semiconductor fabrication lines. It is estimated that production cost for the developed technology would range from $1-10/module, compared to $20-200 for hermetically sealed packages.

Jones, Eric W.↗
NASA NTRS2001

Analysis of long-channel nanotube field-effect-transistors (NT FETs)

This viewgraph presentation provides an analysis of long-channel nanotube (NT) field effect transistors (FET) from NASA's Ames Research Center. The structure of such a transistor including the electrode contact, 1D junction, and the planar junction is outlined. Also mentioned are various characteristics of a nanotube tip-equipped scanning tunnel microscope (STM).

Toshishige, Yamada↗