Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Al2O3”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

New oxidation features in NiCrAl-Zr revealed by an Auger microprobe

A NiCrAl-0.5 (wt %) Zr alloy, oxidized in air for 1 h at 1180 C was studied using a 30-nm resolution Auger microprobe. Depth analysis was achieved using crater edge profiling. This first application of AES to these alloys enabled several new observations of the chemical composition of microstructural features in the corrosion layer. The external oxide was rough, about 2-3 microns thick, and contained Ni, Cr, Al, and O. It was discovered that stoichiometric Al2O3 was restricted to a homogeneous layer about 300-nm thick between the oxide and the base metal. The metal immediately beneath this Al2O3 layer was found to be depleted in Al and roughly ten times richer in Zr than the bulk alloy. These observations are compared with the predictions of current models of the oxidation of MCrAl alloys.

Larson, L. A.↗
NASA NTRS1982

Work of fracture in aluminum metal-matrix composites

Mechanical tests were conducted on B/Al composites and, for comparison, FP-Al2O3/Al composites in the as-fabricated condition and following high-temperature isothermal exposure or thermal cycling. In B/Al (1100), isothermal exposure at 773 K for 125 hr reduced toughness, measured by the work of fracture, from 76 to 10 kJ/sq m, and a similar reduction was observed after equivalent thermal cycling. In B/Al (6061), the same isothermal exposure reduced toughness from 44.5 to 8 kJ/sq m, but the effect of thermal cycling was less detrimental. In FP-Al2O3/Al, the work of fracture was insensitive to either type of treatment. Experimental results are interpreted in terms of matrix softening, interface properties, and fiber notch sensitivity.

Skinner, A.↗
NASA NTRS1982

Meteorological assessment of SRM exhaust products' environmental impact

The environmental impact of solid rocket motor (SRM) exhaust products discharged into the free air stream upon the launching of space vehicles that depend upon SRM boosters to obtain large thrust was assessed. The emission of Al2O3 to the troposphere from the SRMs in each Shuttle launch is considered. The Al2O3 appears as particles suitable for heterogeneous nucleation of hydrochloric acid which under frequently occurring atmospheric conditions may form a highly acidic rain capable of damaging property and crops and of impacting upon the health of human and animal populations. The cloud processes leading to the formation of acid rain and the concentration of the acid that then reaches the ground, and the atmospheric situations that lead to the production of cloud and rain at and near a launch site, and the prediction of weather conditions that may permit or prohibit a launch operation are studied.

Dingle, A. N.↗
NASA NTRS1982

Oxidation of low cobalt alloys

Four high temperature alloys: U-700, Mar M-247, Waspaloy and PM/HIP U-700 were modified with various cobalt levels ranging from 0 percent to their nominal commercial levels. The alloys were then tested in cyclic oxidation in static air at temperatures ranging from 1000 to 1150 C at times from 500 to 100 1 hour cycles. Specific weight change with time and X-ray diffraction analyses of the oxidized samples were used to evaluate the alloys. The alloys tend to be either Al2O3/aluminate spinel or Cr2O3/chromite spinel formers depending on the Cr/Al ratio in the alloy. Waspaloy with a ratio of 15:1 is a strong Cr2O3 former while this U-700 with a ratio of 3.33:1 tends to form mostly Cr2O3 while Mar M-247 with a ratio of 1.53:1 is a strong Al2O3 former. The best cyclic oxidation resistance is associated with the Al2O3 formers. The cobalt levels appear to have little effect on the oxidation resistance of the Al2O3/aluminate spinel formers while any tendency to form Cr2O3 is accelerated with increased cobalt levels and leads to increased oxidation attack.

Barrett, C. A.↗
NASA NTRS1982

Molecular-orbital model for metal-sapphire interfacial strength

Self-consistent-field X-Alpha scattered-wave cluster molecular-orbital models have been constructed for transition and noble metals (Fe, Ni, Cu, and Ag) in contact with a sapphire (Al2O3) surface. It is found that a chemical bond is established between the metal d-orbital electrons and the nonbonding 2p-orbital electrons of the oxygen anions on the Al2O3 surface. An increasing number of occupied metal-sapphire antibonding molecular orbitals explains qualitatively the observed decrease of contact shear strength through the series Fe, Ni, Cu, and Ag.

Johnson, K. H.↗
NASA NTRS1983

The oxidation behavior of a model molybdenum/tungsten-containing alloy in air alone and in air with trace levels of NaCl(g)

Thermogravimetric, metallographic, and X-ray studies of a model alloy, Ni-(17 a/o)Al-(10 a/o)Mo+W, oxidized in dry air at 600-1200 C and in air with 10 ppm NaCl gas at 900 C, are reported. The alloy was melted under Ar and pretreated in flowing H2 for 24 h at 1300 C. Polished 1.3 x 1.3 x 0.2-cm specimens were washed and degreased prior to oxidation in a quartz tube within a furnace for up to 120 hr. The oxidation activation energy of the alloy is determined to be about 30 kcal/mole. The specimens oxidized at 900 C and hotter exhibited oxidized and nitrided phases covered by complex NiMoO4, NiWO4, and NiAl2O4 scales and a porous, nonprotective outer layer of NiO. The oxidation behavior is found to be determined by the formation and growth of the scale, especially the (Mo,W)O2 component. Al2O3 scale layers were not formed, and further runs with pure O2 or Ar-(20 percent)O2 ruled out an explanation of this phenomenon based on aluminum nitride formation. The oxidation was accelerated by the addition of NaCl gas, a finding attributed to the reaction of NaCl with external locally protective Al2O3 scales and with the internal(Mo, W)O2 layers.

Smeggil, J. G.↗
NASA NTRS1983

Low temperature hot corrosion

The reaction of Co-Cr, Ni-Cr, Co-Cr-Al, and Ni-Cr-Al alloys with Na2SO4 in the presence of SO3 at temperatures between 700 and 750 C leads to the formation of liquid CoSO4-Na2SO4 or NiSO4-Na2SO4 deposits on the alloy surface. The formation of Cr2O3 and/or Al2O3 below this deposit results in a locally low P(O2) and a higher P(S2) and P(SO2). It is noted that these conditions can prevent protective oxide formation either by sulfide formation in the alloy, which localizes the Cr and/or Al in discrete particles, or by acid fluxing involving a reaction between Al2O3 or Cr2O3 and SO2 to form a salt-soluble species and subsequent reprecipitation as porous oxides in regions of higher P(O2). These processes may occur simultaneously, although a given alloy generally exhibits features of predominantly one type. Here, the Ni-Cr and Ni-Cr-Al alloys, and to some extent the Co-Cr alloys, exhibit features indicative of the sulfidation mechanism, whereas the morphology for the Co-Cr-Al alloy is more consistent with a predominant acid fluxing mechanism.

Chiang, K. T.↗
NASA NTRS1983

Photodeposition of aluminum oxide and aluminum thin films

Uniform films of Al2O3 have been photodeposited using an excimer laser operating at 248 nm (KrF) or at 193 nm (ArF) and trimethylaluminum and N2O as the reactants. Deposition rates were typically 2000 A/min and the physical, chemical, and electrical properties of the photodeposited Al2O3 films are comparable to films deposited using conventional techniques. Properties of photodeposited aluminum films are also presented.

Solanki, R.↗
NASA NTRS1984

Material growth and characterization for solid state devices

During the reporting period, InGaAs was grown on Fe-doped (semi-insulating) (100) InP substrates by current controlled liquid phase epitaxy (CCLPE) at 640 C and current densities of 2.5A sq/cm to 5 A/sq cm for periods from 5 to 30 minutes. Special efforts were made to reduce the background carrier concentration in the grown layers as much as possible. The best layers exhibited carrier concentrations in the mid-10 to the 15th power/cu cm range and up to 10,900 sq cm/V-sec room temperature mobility. InGaAsP quaternary layers of energy gap corresponding to wavelengths of approximately 1.5 microns and 1.3 microns were grown on (100) InP substrates by CCLPE. In the device fabrication area, work was directed toward processing MISFET's using InGaAs. SiO2, Si3N4 and Al2O3 were deposited by ion beam sputtering, electron beam evaporation and chemical vapor reaction on Si, GaAs, and InGaAs substrates. SiO2 and Si3N4 sputtered layers were found to possess a high density of pinhole defects that precluded capacitance-voltage analysis. Chemical vapor deposited Al2O3 layers on Si, GaAs and InGaAs substrates also exhibited a large number of pinhole defects. This prevented achieving good MIS devices over most of the substrate surface area.

Stefanakos, E. K.↗
NASA NTRS1983

Development of plane strain fracture toughness test for ceramics using Chevron notched specimens

Chevron-notched four-point-bend and short-bar specimens have been used to determine the fracture toughness of sintered aluminum oxide and hot-pressed silicon nitride ceramics. The fracture toughness for Si3N4 is found to be essentially independent of the specimen size and chevron notch configuration, with values ranging from 4.6 to 4.9 MNm exp -3/2. In contrast, significant specimen size and notch geometry effects have been observed for Al2O3, with the fracture toughness ranging from 3.1 to 4.7 MNm exp -3/2. These effects are attributed to a rising crack growth resistance curve for the Al2O3 tested.

Bubsey, R. T.↗
NASA NTRS1983

Compositional effects on Si3N4 fracture surfaces

Surface analysis techniques (X-ray, infrared reflection spectroscopy, Auger electron spectroscopy) applied to the same samples reveal that fracture surfaces of Si3N4 with Y2O3 densification aids possess a higher concentration of oxygen than the bulk. The oxide densification aids thus concentrate in the grain boundaries, and even low-temperature fracture is seen as occurring preferentially within the oxygen-enriched grain boundaries. It is found that increasing the concentrations of Y2O3 and Al2O3 increases the oxygen content of the fracture surface. A range of 13-15 percent Y2O3 + 6 percent Al2O3 gives an amorphous grain-boundary phase that is resistant to devitrification. Fracture occurs through the amorphous phase, and heat treatment at 1000 C has little effect on the amorphous phase.

Hench, L. L.↗
NASA NTRS1984

Observation of surface states on gold films by electron tunneling spectroscopy

It is pointed out that inelastic electron tunneling spectroscopy (IETS) is a useful technique for the study of vibrational modes of molecules adsorbed on the surface of the insulating layer in a metal-insulator-metal tunnel junction. A detailed study of electron tunneling in aluminum-aluminum oxide-gold (Al-Al2O3-Au) tunnel junctions has been conducted with an overall goal of exploring possible mechanisms in such a thin film device useful for chemical sensing. For an understanding of the electronic effects in the presence of chemicals in a junction, the electronic surface properties of the metallic films in a clean tunnel junction must be established. The present investigation is concerned with room temperature observations of electronic states on the surface of highly oriented gold film in Al-Al2O3-Au junctions.

Lambe, J.↗
NASA NTRS1984

Chemical and physical studies of type 3 chondrites. III Chondrules from the Dhajala H3.8 chondrite

Thermoluminescence (TL) properties have been measured in 58 chondrules separated from the Dhajala H3.8 chondrite. The pyrolytic chondrules are noted to have higher mass-normalized TL values than nonpyrolytic ones. Significant correlations are noted between log(TL) and the bulk CaO, Al2O3, and MnO content of the chondrules. These, together with correlations of log(TL) with the CaO, Al2O3, SiO2 and normative anorthite content of the chondrule glass, indicate an association of the TL and the abundance and position of mesostasis. It is suggested that the TL level in a given chondrule is governed by its bulk composition and metamorphism, and it is hypothesized that the devitrification resistance of unequilibrated chondrule mesostasis explains the unequilibration of certain chondrules in type 3 ordinary chondrites.

Sears, D. W. G.↗
NASA NTRS1985

Tensile test of pressureless-sintered silicon nitride at elevated temperature

Uniaxial tensile strength tests of pressureless sintered silicon nitride were carried out in air at temperatures ranging from room temperature up to 1600 C. Silicon nitrides containing Y2O3, Al2O3, Al2O3-MgO, or MgO-CeO2 additives were tested. The results show that the composition of the additive used influences the strength characteristics of the silicon nitride. The tensile strength rapidly decreased at temperatures above 1000 C for the materials containing MgO as the additive and above 1000 C for the material with Y2O3. When the temperature increased to as high as 1300 C, the strength decreased to about 10 percent of the room temperature strength in each case. Observations of the fracture origin and of the crack propagation on the fracture surfaces are discussed.

Matsusue, K.↗
NASA NTRS1984

Advanced thin film thermocouples

The fabrication, materials characterization, and performance of thin film platinum rhodium thermocouples on gas turbine alloys was investigated. The materials chosen for the study were the turbine blade alloy systems MAR M200+Hf with NiCoCrAlY and FeCrAlY coatings, and vane alloy systems MAR M509 with FeCrAlY. Research was focussed on making improvements in the problem areas of coating substrate stability, adhesion, and insulation reliability and durability. Diffusion profiles between the substrate and coating with and without barrier coatings of Al2O3 are reported. The relationships between fabrication parameters of thermal oxidation and sputtering of the insulator and its characterization and performance are described. The best thin film thermocouples were fabricated with the NiCoCrAlY coatings which were thermally oxidized and sputter coated with Al2O3.

Kreider, K. G.↗
NASA NTRS1985

Size and shape dependence of CO adsorption sites on sapphire supported Fe microcrystals

The surface structure and stoichiometry of alumina substrates, as well as the size, growth characteristics, and shape of Fe deposits on sapphire substrates have been investigated by low energy electron diffraction (LEED), Auger electron spectroscopy, electron energy loss spectroscopy, and X-ray photoemission spectroscopy (XPS), as well as work function measurements, in conjunction with transition electron microscopy observations. The substrates used in this work were the following: (1) new, clean Al2O3; (2) same surface amorphized by Ar ion bombardment; (3) same surface regenerated by 650 C annealing; (4) amorphous alumina films on Ta slab; and (5) polycrystal alumina films, obtained by heating amorphous films to 600 C. Substrate cleaning was found to be most effective in producing a reproducible surface upon oxygen RF plasma treatment. The Fe nucleation and growth process was found to depend strongly on the type of substrate surface and deposition conditions. Ar ion bombardment under beam flooding, and subsequent annealing at 650 C was found an effective means to restore the original Al2O3 (1102) surface for renewed Fe deposition.

Papageorgopoulos, C.↗
NASA NTRS1984

Achondrite ALHA77005 - Alteration of chromite and olivine

The olivine crystals of the 77005 achondrite are brown except for colorless shock lamellae, mottled patches, and grains adjacent to pools of impact melt. Sporadic dark alteration patches in brown olivine and Cr-rich spinel gave the following average electron-microprobe analyses: (olivine) P2O5 0.9, SiO2 57.9, TiO2 0, Al2O3 0.7, Cr2O3 0.4, V2O3 0, Fe2O3 (assumed oxidation state) 17.0, MgO 1.6, CaO 0.2, Na2O 0, K2O 1.8, SO3 (assumed oxidation state) 9.2, Cl 0.1, sum 89.8 wt pct; (spinel) P2O5 3.5, SiO2 2.1, TiO2 2.2, Al2O3 2.1, Cr2O3 13.4, V2O3 0.8, Fe2O3 40.7, MgO 0.9, CaO 0.1, Na2O 0, K2O 2.0, SO3 11.1, Cl 0.1, sum 79.0 wt pct. Ion-microprobe analyses revealed H in both. Rare orange patches in brown olivine from another area gave SiO2 33-35, FeO 30-28, MgO 28-32, sum 93 wt pct. Thermal metamorphism under dry oxidizing conditions is discussed as a possible alternative to shock-induced oxidation for generation of the brown olivine (McSween and Stoeffler, 1980). Because alteration patches transgress shock lamellae, and because sulfatic alteration occurs in fusion crusts of Antarctic meteorites (Gibson et al., 1983), alteration of the 77005 achondrite at the Antarctic surface is preferred to a complex series of processes needed for preterrestrial alteration.

Smith, J. V.↗
NASA NTRS1985

Current viewpoints on oxide adherence mechanisms

Additional hot stage Auger experiments have provided surface segregation data for NiCrAl + or - Y or Zr alloys in agreement with other investigations. This data, combined with experimental and theoretical evidence of the Al2O3-metal bond strength, is presented in support of a chemical mechanism of Al2O3 scale adhesion. Both the detrimental effects of sulfur segregation and the beneficial effects of dopant segregation may be important. Chemical features of the dopants are compared in light of these proposed mechanisms, namely delta H sub f (sulfide), delta H sub f (oxide), electron orbital configuration, and insolubility in Ni.

Smialek, J. L.↗